Encoding way higher than I set

I have my fme set to 320x240, 200kbps and 25 fps ( yes I know its low) what I start the encoder it try's to uncode 400 or 500 fps and bit rate of 2000 to 3000 kbps, it worked when I first got it then had this problem, after waiting a few months it worked again in limiting to my settings, then all the sudden it's back to this problem, it's not cpu, i've check and even used cmd to run it. I'm lost, it doesn't matter what I try to stream or from what program, even a black pic still encodes this high.
Intel core i7 920 2.67 GHz
3gb memory
Vista Home Premium 64 bit

Looks like device is not behaving properly. it's not providing correct input? Are you using screen capture device?
Please share FMLE settings and try same thing with using VP6 codec.

Similar Messages

  • The bottom list of apps on my ipod touch screen is way higher than its suppose to be

    hi i have an ipod touch 2nd generation i dont update it to often cause i have very very slow iternet and it can take up to 4 hours and i dont have the time to update it but the bottom list of apps i dont know what its called but i think its the app bar is way higher than normal i dont know why the only app i really use is pandora i dont know if that helps

    HI,
    Try a Reset of your Device... You will not lose any data 
    Turn iPod touch off and turn it on again.
    Press and hold the Sleep/Wake button on top of iPod touch for a few seconds until a red slider appears, and then slide the slider.
    Then press and hold the Sleep/Wake button until the Apple logo appears.
    From Here   http://support.apple.com/kb/ts2771

  • Billing higher than amount setting in FD32

    Hello!
    We define the credit limit of 94852.57 for a client. However, the Sales Depart got 118,251.71 billing . It is an amount 23399.15 higher from our limit. The SAP should not allow only the resource allocation of sales orders and invoicing to the value set in FD32? Is there a setting of tolerance? The balance of down payments can influence this calculation?
    Thank you in advance.

    - Check Seasonal factor in % in OVA8
    It specifies a percentage tolerance limit up to which a customer's credit limit may be temporarily extended or reduced.
    If you enter 5% in this field and select the <Minus field, a customer's usual credit limit of 10,000 USD is extended by a further 500 USD.
    - If you have some specific condition, then you can also go for "No credit check". Number of the routine used for copying checks a requirement at a specific time. So, here you can specify a routine number that contains conditions for when a credit limit check should take place.
    - Credit check: Deviation of document value by x %. It specifies a deviation factor for documents that have already been approved for credit. Example-You set the deviation factor at 10%. An order for 10 boxes of a material (price = 100 USD per box) has a total value of 1,000 USD and is approved for credit. The customer then calls and wants to add additional boxes to the order. If this causes the deviation factor to exceed 10%, the system carries out another credit check. So, enter a percentage.
    Hope it can assist you.
    Thanks & Regards
    JP

  • Localization in OBIEE 10g(Error "start row is set higher than the row count

    Hi All,
    I m Working on Localization.
    I have used exteranize string and saved excel file and added language column and inserted data en and fr and loaded the file into the database.
    then i have created 2 variables
    one is for weblanguage SELECT 'VALUEOF(NQ_SESSION.WEBLANGUAGE)' FROM DUAL
    second is SELECT SESSION_VARIABLE, TRANSLATION FROM TAB_EXTERNAL WHERE LANGUAGE = 'VALUEOF(NQ_SESSION.LOCALE)' when i click on Test for the second variable it showing error
    "start row is set higher than the row count"
    i have seleted start row =10 and show some 10.then also it is showing same error.
    Please send me the solution ASAP.
    Thanks and Regards
    Kiran Kumar

    Hi Kiran,
    I am working in OBIEE localization. I created two variables and when press test i am getting vaules successfully. But in OBIEE application i am getting columns in english only. It seems there is some problem with values in DUAL table. It contains only 1 column called 'DUMMY' and value as 'X'.
    Please give me complete configuration steps to setup localization OBIEE 10g. Please drop me a mail to [email protected] if u have steps. I will call u if u provide contact number.

  • HT4623 Is there any way to update iphone 3G higher than 4.2.1

    Is there any way to update iphone 3G higher than 4.2.1

    thanks for the info.. i guess i need to throw this thing to the far far away its make to much headache ^_^ anyway thanks guys...

  • Table creation Error "Ref Count for this object is higher than 0"

    Hi All
    I have a problem in creation of table using SDK on a button event.  I have a procedure to create tables and fields. If I call this procedure on a menu Event than it works fine but If I call this procedure on a button event than It gives error "Ref count for this object is higher than 0" . I know this error occur When an object does not release after creating a table. but this error occur at when first table is created. My code it given below. plz see and give me your valuable suggestions.
      Dim oUserTablesMD As SAPbobsCOM.UserTablesMD
                Try
                    oUserTablesMD = B1Connections.diCompany.GetBusinessObject(SAPbobsCOM.BoObjectTypes.oUserTables)
                    oUserTablesMD.TableName = "AM_OBIN"
                    oUserTablesMD.TableDescription = "PutAway Table"
                    oUserTablesMD.TableType = BoUTBTableType.bott_Document
                    lRetCode = oUserTablesMD.Add
                    '// check for errors in the process
                    If lRetCode <> 0 Then
                        B1Connections.diCompany.GetLastError(lRetCode, sErrMsg)
                        MsgBox(sErrMsg)
                    Else
                        B1Connections.theAppl.StatusBar.SetText("Table: " & oUserTablesMD.TableName & " was added successfully", BoMessageTime.bmt_Short, BoStatusBarMessageType.smt_Success)
                    End If
                    System.Runtime.InteropServices.Marshal.ReleaseComObject(oUserTablesMD)
                    oUserTablesMD = Nothing
                    GC.Collect()
                    oUserTablesMD = B1Connections.diCompany.GetBusinessObject(SAPbobsCOM.BoObjectTypes.oUserTables)
                    oUserTablesMD.TableName = "AM_BIN1"
                    oUserTablesMD.TableDescription = "PutAway Upper Grid"
                    oUserTablesMD.TableType = BoUTBTableType.bott_DocumentLines
                    lRetCode = oUserTablesMD.Add
                    '// check for errors in the process
                    If lRetCode <> 0 Then
                        If lRetCode = -1 Then
                        Else
                            B1Connections.diCompany.GetLastError(lRetCode, sErrMsg)
                            MsgBox(sErrMsg)
                        End If
                    Else
                        B1Connections.theAppl.StatusBar.SetText("Table: " & oUserTablesMD.TableName & " was added successfully", BoMessageTime.bmt_Short, BoStatusBarMessageType.smt_Success)
                    End If
                    System.Runtime.InteropServices.Marshal.ReleaseComObject(oUserTablesMD)
                    oUserTablesMD = Nothing
                    GC.Collect()
                Catch ex As Exception
                    MsgBox(ex.Message)
                End Try
    Thanks
    Regards
    Gorge

    Hi Gorge,
    The "Ref count error..." usually occurs in case of Meta Data objects not being properly cleared.  And yes, you have got the error in the right place, generally while creating tables / fields / UDOs.  For this, you just need to clear the Meta Data object (At times even DI objects like Record Set) once they are used.
    Eg: Release these objects in the below way in a Finally Block.
    System.Runtime.InteropServices.Marshal.ReleaseComObject(oRecordSet);
    Hope this helps.
    Regards,
    Satish

  • Create variant for VL10b for max delivery date higher than 30 days

    Hi expert,
    I want to create a variant for the transaction VL10b with a max delivery date higher than 30 days.
    The standard transaction make 30 days as default.
    How can a proceed?
    Thanks for your help.
    Regards,
    Haja

    Hi Haja,
    From the moment you run your variant via transaction VL10B, the delivery creation date
    range will get the values saved in your variant. In a second step, when you click
    on "Purchase Order" Tab, the system will re-determine the Delivery creation date
    range taken into account the fact that field CalcRuleDefltDlvCrDt is empty and that
    MaxDelivCreateDate (visible in the variant) is equal to 30.
    Please note, the date calculation is being influenced by 2 factors :
    -The MaxDelivCreateDate field whose default value can be modified in 2 different ways:
      a) either in customizing via transaction VL10CUC
           or
      b) manually, after unchecking the "Use list profile" check box in the user role of VL10.
          By doing this, the field will be made visible and can then be manually modified.
    Afterwards, the date calculation is also controlled by the rule defined in CalcRuleDefltDlvCrDt field. You can then possibly also set this field to blank or define your own calculation rule via an
    user-exit (include V50R_USEREXIT_PREPARE). If the rule is set to 2, then regardless of the
    value stored in MaxDelivCreateDate, the date range will only cover today and tomorrow.
    These are the only 2 influencing factors for the program (not the variable type in the variant). Please try any combination you may need and this should suit your needs.
    BR,
    Enrique

  • Scxi 1112 can not acquire correct data at high temperature(higher than 700C)

    A scxi-1112 module in scxi-1001 chassis is used to acquire oven Temperature. Software is LabView 8.5. when oven is ramping higher than 700C, the module gets wrong data, the data acquisition VI shows random values around 700C.It seems the scxi-1112 module "reaches" its maximum setting, which actually is 1000C. Can Anybody explain what's happening to me? Thanks.

    Hi gq,
    Could you please provide a screenshot of the
    way you are configuring the task, as well as what the data looks like
    that you are seeing when it behaves incorrectly? If you just perform a
    voltage reading (instead of a temperature task), what values are
    returned, and does it show the same behavior of reaching a certain
    voltage and not ramping any higher? Also, how do you have your
    thermocouple attached to your oven; is there any possibility that the
    connection is conducting at that temperature? Also, regarding the use of different measurements in the task, are you using different modules in your system or are the measurements being done on the same 1112 module? Additionally, have you tried other channels and received the same problem? I look forward to reading your response.
    Regards, 
    Daniel S.
    National Instruments

  • High than 16 MIDI channels.

    Hello,
    I have created several orchestra files in Finale which allow up to 128 MIDI channels. I'm only using and hoping to use 32. I realize the original MIDI specs allow for only 16, BUT
    but Finale, and Home Concert Extreme allow for more using A and B or other multiple sets of 16 structure.
    QUESTION: In there any way to Assign a higher-than-16 midi channel to a Region or Track in Logic Pro? Kind of like a Maximum number of x. parameter, only for MIDI channels.
    I have two applications ready and willing to open, understand and correctly channel these higher-than 16 channels embed files.
    Please help if possible.

    Gentleman, thank you for all the help.
    Here is my studio configuration.
    I am Using Home Concert Extreme ( a change of tempo following software) to Play (meaning read without editing ) an underling MIDI file. These underlying MIDI files are created by FINALE can have 32 channels ( i think), or they may just have 2 separate tracks per channel. And some are created by Logic. It doesn't really matter.
    WHen I "open" these files in Home Concert Extreme, I have to re-channelize half the tracks form MIDI A to MIDI B. Kind of like separating conjoined twins.. 2 come in together.. but then are re-directed to live separate lives.)
    ANYWAY... Here is the BUG. I am trying to play these in software HomeConcertExtreme BUT use the SOUNDS (virtual instrument settings) in Logic Pro which are infinitely superior to the default of QuickTime GM Synth sounds.
    So... got some advice to use the IAC Driver.. did.
    I got some advice to check "Auto demix by channel if multitrack recording." Under Settings> Recording.. Did that too. Works perfectly for fewer than 17 channels.
    So am not using an external sound card, nor am I using an external MIDI interface to play back.
    Its going from HCX to IAC Drive to Logic all in the computer.
    Here is how logic is responding:
    I have 2 different channel 12's set up in HCX
    A-12 is for Piano LH
    B-12 is for Violin
    in Logic I have
    Instrument 12 channel 12 all laid out nice in anticipation for the piano notes, and
    Instr. 28 channel 12 all laid out for the violin notes.
    Unfortunately Here is what I get.
    If both tracks are record enabled in usually de-mixes properly.
    But if the piano is not enabled both the piano notes and violin notes sound like Violin.
    if the violin is not record enables both the piano notes and violin notes sound like a piano.
    Is this going to happen CONSISTENTLY as a rule?
    Just for kicks, in the environment, I change the track that I laid out for the piano in Logic (instr 12 channel 12
    to instrument 12 channel 13 and it still played the piano notes but on a different sound -
    organ.
    Just for kicks I then changed the piano track to instrument 16 channel 16 and the piano notes still followed me.
    Where are the rules?
    How does it channelize?
    Does each in coming channel just look for the first available (record enabled) channel and jump on it; like the characters of Space Balls jumping in emergency escape pods.
    How can I count on a 24 channel orchestra to all find their instruments???????
    please help.
    -Curtis

  • Tv@nywhere Master - Cant capture higher than 352X288

    Hi
    I have a Tv@nywhere Master and i cant capture any higher that 352x288 resolution.
    I tryed VirtualDub and Adobe Premier . They both say : Unsuported Video Format when i try to select 640x480 or 720x576 . (PAL mode)
    The original software (MSIPVS) lets me choose the format and resolution but i dont want to use it because it offers poor quality.
    I am capturing from VHS at maximum quality possible and storing it in AVI uncompressed and then use TMPEGenc to SVCD.
    Can anyone comment on this ?
    Doesnt this board capture higher than 352x288 ???
    Thank you
    Filipe

    I use it in 768x576 without any problems
    you just have to look for a   Use Smart Tee Filter  setting because the card can`t both capture and preview over 288 so you`ll need to split the data on the Capture pin in order to provide preview over 288 lines.

  • Is it possible to raise the bit rate of songs higher than 256 on iTunes? If not what should i use or do to raise the bit rate of songs?

    Is it possible to raise the bit rate of songs higher than 256 on iTunes? If not what should i use or do to raise the bit rate of songs?

    Songs you rip from CD can have their bitrate increased to a maximum of 320Kbps from the iTunes preferences; alternatively, the default encoder can be changed to a lossless one. Songs from other sources have a fixed maximum bitrate.
    (67928)

  • I received my new Verizon Edge bill in the mail and it is $80 higher than my old plan.  I have been so unhappy with this change over.  Went through hell getting our second phone activated because of a weird computer glitch and when we asked if we would re

    I received my new Verizon Edge bill in the mail and it is $80 higher than my old plan.  I have been so unhappy with this change over.  Went through hell getting our second phone activated because of a weird computer glitch and when we asked if we would receive any consideration for the time, travel, and money we put into getting the phones the way they were supposed to be, we were told to wait until the bill came and then they could make adjustments.  Now I have the bill and have no idea "who" the we would be that could make adjustments.  To top it off, the only way I know my account will get any attention is to post this in chat.  I am so disappointed and will be counting the months until our phones are paid off and we can change companies.

    Call 800-922-0204
    I just purchased a new device using Verizon Edge. Why does my bill look higher than normal?
    There’s two reasons why your first bill after signing up for Edge might be higher than normal:
    Prorate Charges – If you upgraded an existing line and did a price plan change, you may have price plan charges and credits that went into effect the day you upgraded.
    Sales Tax – Most states require sales tax on the full retail price paid by the customer, which in most instances will be charged at the time of the first invoice.
    Note: Customers who purchased devices in AL, AZ, CO, IL, NM, ND or SD will be billed taxes and surcharges monthly as payments are made.
    Your bill will normally include:
    Your last Edge installment payment
    The next Edge installment charge
    If you are on a MORE Everything Plan, a monthly access discount for each qualifying line.
    The details of Edge installments and discounts can be viewed at the line level portion of your bill under Monthly Charges and Equipment Charges, or in My Verizon, My Bill then Charges By Line.

  • Has anyone had any luck compressing videos with resolutions higher than 1080?

    Everytime I try, it fails instantly.  Is this not allowed in Compressor 4?  It was possible in Compressor 3.

    I have a 4K video that I'd like to compress using H.264 or X.264 and restrict the data rate.
    Here are some details of the video (created in Motion) I am trying to compress:
    DIMENSIONS: 4096 x 2048
    FORMAT: H.264
    FPS: 24
    DATA SIZE: 53.2 MB
    DATA RATE: 52.03 MB
    and here are settings that I would like to compress it with using Compressor 4.0.4:
    CODEC: H.264 or X.264 (both fail)
    FRAME RATE: current
    KEY FRAMES: Automatic
    DATA RATE: Restricted to 7000 kbits/sec (setting it to automatic or any other data rate also fails)
    QUALITY: Best
    HEIGHT AND WIDTH: 100% of source
    I have been able to get a successful compression with this 4K video file using ProRes 422, so that leads me to think this is a codec problem, not a Compressor application problem. Furthermore, I have had the same problem just using Quicktime 7 to export a video with these settings, I get the same failed results.
    In Compressor it gives me the message Failed: Quicktime Error: -108
    and in Quicktime 7 it gives me the message Failed: qKitErrorCatchAll (-6662)
    So, if you had any suggestions about a better codec to use, one that allows me to restrict the data rate on higher than 1080 video files, it would be much appreciated.
    Thanks
    Evan

  • Edit catt script for changes in in web appl server higher than 6.4 release

    Hello Guru’s,
    Will you help me in editing the CATT script for changes in Web application server release higher than 6.4 release, when I look for edit mode it was showing the following message. will anyone suggest me is there any way to make changes.
    “While I was choosing change mode it was displaying the above message ( Message No:TT005)”
    Full points for the answer

    It seems there there is no problem with my FireFox 7.0.1 on my Mac OSX 10.7.2. So, maybe you can solve the problem by updating your OS. The only minor problem here is that Firefox doesn't display in the Tibetan fonts that you choose, it always display in Kailas font for Tibetan.

  • GR Quantity Higher than PO Quantity

    Dear SAP Guru,
    Pl suggest,
    GR Qunatity is higher than PO Qunatity. PO Qunatity is 40, GR is to be done twice, 1st time 22.5 and next time 20, but system not allowing to do this.
    Pl suggest if nay way if have.
    Regards,
    Jyoti

    Hi Anjali ,
    I have done all 3 points out of 4 . last one PO creation I have not doen and tested in dev.
    Ticked on Unlimited button and also also given 50% over delev tolarence. then doing GR, system giving a message
    PU Ordered quantity exceeded by 5 TO : RAW01 1000 RAW
    Pl suggest.
    Regards,
    Jyoti

Maybe you are looking for