Encore Quit working, now I cannot reinstall it

While exporting a dvd from premiere pro cs3 to encore, encore tried to start up and BINGO! wouldnt start up, gave me an error!
So I attempted to uninstall encore...fine...but now I cannot reinstall encore. It stops while trying to work with components. "component install failed"
Running xp-pro. Does anyone have suggestions? I am in a wee bit of a pickle.

download and run this to remove Final Cut:
FCS Remover

Similar Messages

Why do I keep getting the message that iTunes is quitting working? I have reinstalled iTunes and I have checked the WiFi twice. I have even put the internet cable directly into the laptop and still I cannot connect to the iTunes. Offers no solutions.

Why do I keep getting the message that iTunes is quitting working? I have reinstalled iTunes and I have checked the wifi twice. I have even put the internet access cable directly into the laptop. The message says that windows will look for a solution but never offers any solution.

Try disconnect your internet, then launch iTunes.
Connect your device, then reconnect your internet.
See if this resolves the issue.

My motherboard "fried" on my computer when the fan quit working. I cannot access my hard drive on my old computer. I just downloaded ITunes on my new computer; assumed it would pull all my playlists in under my Apple ID and password-no such luck. Help?

My motherboard "fried" on my computer when the fan quit working. I cannot access my hard drive on my old computer. I just downloaded ITunes on my new computer; assumed it would pull all my playlists in under my Apple ID and password-no such luck. Help Please?

If your external drive does not have an independent power supply, you may wish to consider a couple of lower-cost options before tossing the drive. Bus-powered drives have no external power source and must get all their power from the computer. They can exceed the computer's USB energy budget.
Cheapest option:
1 Meter USB 2.0 A to 5 Pin Mini B Cable - Auxiliary USB "Y" Power Design for external hard drives.
This gets power from two of the computers USB porst sna can provide enough power to wake up an under-performaing bus-powered drive.
If you don't have enough ports to use this, try the next cheapest option:
Newer Technology 7 Port Hi-Speed USB 2.0 Hub with Power Adapter for Mac & PC
Such a hub has a an independent power supply to make up for wahat the comptuer fails to provide.

I uninstalled Adobe Air and Adobe Reader and now I cannot reinstall them on the Adobe web site. I go thru the steps on Adobe site and never get a popup to RUN any programs.

I uninstalled Adobe Air and Adobe Reader and now I cannot reinstall them on the Adobe web site. I go thru the steps on Adobe site and never get a popup to RUN any programs.

Then there is something seriously wrong with either your
browser
Windows
Internet connection
I have just downloaded that installer (on Windows 7, using Pale Moon), and the download completed within less than 10 seconds. And I am some 10,000km away from the Adobe download servers.
Can you try a different browser?
Can you download anything to your computer, e.g. from Microsoft?

Had itunes then one day it quit working, now all i get when i open is this:itunes has quit working box

My son received a laptop for christmas last december..Itunes has worked on it up until about a month ago. Now the program states this: Itunes has quit working- we have uninstalled and reinstalled earlier verions as well as the new version. they all go through the process but when it finalizes and we open it says the same thing. under the details of the error we get all this stuff:
Problem signature:
problem Event Name:
APPCRASH
Application Name:itunes.exe
Application Version: 10.6.3.25
It goes on forever with a list of code. We have even tried to the the winsock reset and nothing. Does anyone have any suggestions as to what we need to do? We have done everything the apple support site has stated but nothing seems to work. I hate to think we has lost all his purchased music etc over this. HELP!

'''Try Firefox Safe Mode''' to see if the problem goes away. Safe Mode is a troubleshooting mode, which disables most add-ons.
''(If you're not using it, switch to the Default theme.)''
* On Windows you can open Firefox 4.0+ in Safe Mode by holding the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
* On Mac you can open Firefox 4.0+ in Safe Mode by holding the '''option''' key while starting Firefox.
* On Linux you can open Firefox 4.0+ in Safe Mode by quitting Firefox and then going to your Terminal and running: firefox -safe-mode (you may need to specify the Firefox installation path e.g. /usr/lib/firefox)
* Or open the Help menu and click on the '''Restart with Add-ons Disabled...''' menu item while Firefox is running.
[[Image:FirefoxSafeMode|width=520]]
''Once you get the pop-up, just select "'Start in Safe Mode"''
[[Image:Safe Mode Fx 15 - Win]]
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshooting extensions and themes]] article for that.
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
''When you figure out what's causing your issues, please let us know. It might help other users who have the same problem.''
Please report back soon.

I installed Adobe CC months ago. uninstalled it.. said "with errors" now I cannot reinstall Adobe CC... can anyone tell me what happened so that my money doesn't go to waste?

Uninstalll error. Cannot reinstall. what happened here and how do I fix this?

No one can tell you anything about what happened until you give complete details.
Maybe someone could help you fix your issue.
BOILERPLATE TEXT:
Note that this is boilerplate text.
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
etc.,
someone may be able to help you (not necessarily this poster).
a screen shot of your settings or of the image could be very helpful too.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

Itunes quit working, I uninstalled and reinstalled and it still will not load

Itunes worked great for about a year, Then all of a sudden it quit working (update maybe?)
when I hit the icon it swirls for a second then nothing I uninstalled it and then reinstalled it and still nothing
Ideas

Reapir your QuickTime.
Control Panel > Programs n Features > highlight QuickTime, click CHANGE then REPAIR.

Itunes worked for about 30min. and then quit working, now it says there is a problem and shuts down. TGried uninstal and reinstall but it does the same thing. Will not run.

I am running Windows 8.1 and installed itunes and it worked fine for about 30min. and then icloud started and the itunes and icloud just quit. Tried to run itunes again but got a message "a problem occured and needs to shut down" then it shuts down. I have tried reinstalling but get the same problem. Tried uninstalling and reinstlling but it does the same thing.

I am running Windows 8.1 and installed itunes and it worked fine for about 30min. and then icloud started and the itunes and icloud just quit. Tried to run itunes again but got a message "a problem occured and needs to shut down" then it shuts down. I have tried reinstalling but get the same problem. Tried uninstalling and reinstlling but it does the same thing.

Native apps not working on Yosemite/ Cannot reinstall

After the Yosemite update virtually none of the native apps on my MacBook (mid 2010) launch. ITunes does, but not AppStore, Safari or even 'About this Mac' option. The icons in the dock bounce once and then nothing happens.
Moreover, when trying to reinstall OS using OS X Utilities (command + R when booting) the 'continue' button cannot be clicked: the mouse pointer works ok, but the options in the top left corner like ‘file’, ‘edit’ etc. do not (I can only navigate between the four options by arrow buttons, use ‘ctrl+q’ to quit and that’s just about it). Trying to install OS X from a CD (‘c’ while restarting) I face the same problem, where it lets me choose the language at the beginning but then won’t proceed as the ‘continue’ button does not respond likewise.
Is there any way to restore or reinstall the system? Please, help!

Reinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Also see:
Reinstall OS X Without Erasing the Drive
OS X Yosemite- Reinstall OS X
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
OS X Lion- Reinstall Mac OS X
     Note: You will need an active Internet connection. I suggest using Ethernet
                 if possible because it isthree times faster than wireless.
If you have to install from scratch, then you must first install Snow Leopard using the Installer disc that came with your computer when it was new:
Clean Install of Snow Leopard
Be sure to make a backup first because the following procedure will erase
the drive and everything on it.
     1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
         with your computer. Insert the disc into the optical drive and restart the computer.
         After the chime press and hold down the "C" key. Release the key when you see
         a small spinning gear appear below the dark gray Apple logo.
     2. After the installer loads select your language and click on the Continue
         button. When the menu bar appears select Disk Utility from the Utilities menu.
         After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
         size.) Click on the Partition tab in the DU main window. Set the number of
         partitions to one (1) from the Partitions drop down menu, click on Options button
         and select GUID, click on OK, then set the format type to MacOS Extended
         (Journaled, if supported), then click on the Apply button.
     3. When the formatting has completed quit DU and return to the installer. Proceed
         with the OS X installation and follow the directions included with the installer.
     4. When the installation has completed your computer will Restart into the Setup
         Assistant. Be sure you configure your initial admin account with the exact same
         username and password that you used on your old drive. After you finish Setup
         Assistant will complete the installation after which you will be running a fresh
         install of OS X. You can now begin the update process by opening Software
         Update and installing all recommended updates to bring your installation current.
Download and install Mac OS X 10.6.8 Update Combo v1.1.

Force Quit iWeb now website cannot be found in browser

I force quit iWeb after it taking 10 minutes to publish a photo page. I was playing around with slide shows and dragged and dropped an event onto the page. The event actually had a video clip along with the other pictures and I have a feeling this large file is what was taking so long to publish. I relaunched iWeb and published and now the site cannot be found. What have I done??? :o(

have you tried republishing? also check to see if your logged in to your idisk/mobileme idisk with the account that you want to publish with, to check go to system preferences>mobile me, then sign in.

Lost CS3 serial number and email I used from that purchase is no longer valid, now I cannot reinstall my CS5 after wiping my hard drive clean from a computer problem.

Bought CS3 about 7 years ago under an email address that's been closed for many years and I lost the serial number from that old CS3 and now after doing a clean wipe of my hard drive after some computer glitches, I can no longer install CS5 upgrade as I cannot produce the CS3 serial number. No monkey business, I've been using CS5 since 2011 when I bought it directly from Adobe. What are my options?

Is it possible for you to log in to your OLD Adobe account using that email address to check your history?
https://www.adobe.com/account.html for serial numbers or subscriptions on your Adobe page
If not, you MAY be able to have an employee look up the information linked to that old email address
Adobe contact information - http://helpx.adobe.com/contact.html may help
-Select your product and what you need help with
-Click on the blue box "Still need help? Contact us"
If that doesn't work, you are going to have to buy new... either a subscription or Creative Suite 6

I have an hp dv6910us and the system speakers have stopped working. I cannot reinstall the driver.

I have an hp pavilion dv6910us and the speakers have stopped working and no longer show as installed as a device. I have tried reinstalling the audio device driver, but the hp website does not list a driver for my specific laptop.
Right now it shows that I have a bluetooth audio device installed. I have never installed this device and don't know where it came from.

I had the exact same problem, updating updating the Mbox 2 drivers on the Avid website has fixed the problem.
http://avid.force.com/pkb/articles/en_US/Download/Mbox-2-Drivers?retURL=%2Fpkb%2 Farticles%2Fen_US%2FDownload%2FMbox-2-Drivers&popup=true

TS3992 my wifi quit working and i cannot backup how do you get it to back up?

the wifi does not work for my device and cannot get it to back up now. is there a way to do a backup into icloud without wifi working?

You'll have to back up to itunes. In what way does wifi not work? Can't find a router, can't log in successfully, doesn't stay active once connected?

We had to force quite iMovie, now we cannot get it to open. It keeps saying it is not responding. Any tips?

We were building a video in imovie when it stopped responding. We had to force quite the program. Now when we cannot get imovie to open.
Any tips?

The Problem is resolved by :
Click on the "Start" button. Click "Run." Type the word "cmd" in the open box. When the DOS screen comes up, type "netsh winsock reset." Press "Enter." Type "exit" to close the DOS window and go back to Windows.
Restart the computer.
Thanks to my friend Sunil.
Read more: http://www.ehow.com/how_2125133_do-winsock-reset.html#ixzz2kyccghec

I reformatted iBook G4 - now I cannot reinstall from system restore CDs

I am trying to repair my husband's iBook G4. It would not start up at all, so I mounted it as a Target Disk from my MacBook (2.2 Intel Core Duo, 10.5.6), and saved his important data to an external drive. Then I reformatted the iBook (from my MacBook) and ran Disk Utility on it. It got a clean bill of health. Then I tried to reinstall the OS from the original restore CDs (the 3 gray CDs which came with it.)
It gets as far as the gray Apple screen, then hangs and freezes (the little 'gear' stops spinning). I thought I might be able to install the OS from my MacBook via Target Disk, but whether the disk is in the iBook or the MacBook, it says that 'it cannot install this OS on this computer' - meaning the MacBook. But I don't want to install it on the MacBook! I thought I could install the OS via Firewire, but - apparently not!
Anything I'm missing here? These ARE the original iBook G4 10.3 install disks, and the disk itself seems fine - no weird noises or other indications that it's getting ready to take a dive.
I told him he really needs a newer laptop anyway, and am resigned to replacing it, but I'd like to be able to at least get it going while I look around for another laptop.
Can this iBook be saved? TIA, Alicia

Thanks so much for your quick response, Limnos.
I see what you're saying about TDM - I didn't know it couldn't see the other computer at that stage.
+You should try starting the G4 itself from the CDs so you can install. Insert the CD in the G4 and start up while holding down the C key so it boots from the CD.+
I did that:
+Then I tried to reinstall the OS from the original restore CDs (the 3 gray CDs which came with it.)+
+It gets as far as the gray Apple screen, then hangs and freezes (the little 'gear' stops spinning).+
That is why I tried to get it going another way. The CD drive is not broken, but G4 will not install the OS when I use the original system restore CDs which came with the G4 (or Disk Warrior, for that matter.) I've tried formatting it and partitioning it with Disk Utility, using both GUID and Apple Partition Map. But it still only gets to the gray Apple screen, and the little gear stops spinning and there it freezes.
But it doesn't seem like a complete brick, as it works well enough to start up, chime, recognize the System Folder in the installation disk or Disk Warrior, and be accessed as a Target Disk, so I didn't think I should give up on it entirely before chucking it.
Anything else I should try on that front?

Encore Quit working, now I cannot reinstall it

Similar Messages

Maybe you are looking for