Encore WT8-A - External monitor doesn't not work

Hi all,
I have problem, when I connect an external monitor to Toshiba Encore WT8-A with an HDMI cable, Windows does not recognize it. I tried to use monitors from Samsung, Philips and LG.I use a standard HDMI cable. The cable is OK tested on other devices.
win 8.1 (all updates)
bios 1.6
All the drivers used from the Toshiba Service Station
Thank you for help.
RM

Hello gaizkot,
We've an article that can help get your MacBook Air and your display working together.
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/HT1573
Cheers,
Allen

Similar Messages

External monitor Syncmaster 2494SW not working after 10.6.7 update

External monitor Samsung Syncmaster 2494 SW stopped working after 10.6.7 update on 2011 MacBook Pro. I'm using miniDP-DVI adapter. The monitor shown correctly in Display Properties with right modes and name. MackBook recognizes connection but the monitor goes to PowerSave mode (LED indicator blinks).
Safemode boot, SMC reset, PRAM reset did not help.
Exactly the same setup works perfectly under 10.6.6.

HERE IS THE EASY FIX SOLUTION FOR THIS PROBLEM GUYS:
I have an 15inch MacBook Pro that I've just installed Snow Leopard 10.6.3 on.
Prior to this install, I've had it hooked up to my Samsung SyncMaster 2243 via an Apple MDP/VGA adapter and a third party VGA cable. It has been flashing on and off a black screen every now and then for the past 2 years and I googled that it was just a crappy communication between the MBP and the Samsung... but now since installing 10.6.3, the Samsung display just flashes the desktop for a second then turns black for good - occationally flashing analogue/digtal prompt display. Tried everything for hours. Nothing worked, thought I was gonna have to buy a new all Apple VGA lead then came across Michael's above solution. Tried it and it worked IMMEDIATLY!!! And the monitor doesn't flash black anymore AT ALL!! Whoo-hoo!! Thanks heaps.
WHAT TO DO TO FIX:
Go to => System Preferences => Energy Saver => change graphic settings to Higher Performace.
Cheers!!

Encore WT8 - screen Mirroring on TV does not work

Hello,
I have a KDL42-W653A television which supports screen mirroring over WiFi.
However, I cannot get it to work with the Toshiba Encore W8 tablet.
The tablet detects the television, I enter the number, but the television never shows the tablet's screen.
Both the television and the tablet are on the latest firmware.
Another thread indicates there is an update for HDMI in January. I hope that covers this too.
Anwar

Hi
> I have a KDL42-W653A television which supports screen mirroring over WiFi.
By mirroring over WiFi what technology you mean exactly?
Miracast, Intel WiDi, DisplayLink?
Toshiba Encore supports *Miracast*
To use Miracase both devices needs to support this technology.
Then you can connect to external display very easy:
Tab Settings -> Change PC settings -> PC and devices -> Devices
Here you have to Add a device and you tablet will start searching for a Miracast devices
After the connection has been established, the name of the Miracast device will appear under Projectors
Did you test the video output connecting the table to the TV with an micro-HDMI cable?
Does it work?
Here is also an nice youtube video about the Toshiba Encore WT8 screen output options
http://www.youtube.com/watch?v=kBmInOnrS2U

External monitor with imac not working

Hello.I have problem with external monitor connected to my imac 27 via mini display port to vga connector. It was working perfectly but around month ago it suddenly stopped. It looks like my monitor doesn`t get any signal from imac, at least that`s what is says on external monitor.. also, when monitor is connected my mouse is jumping all over the place. I`ve been looking everywhere but i couldn`t find solution to this problem and i know there are many people having the same issue. Did anyone find solution?

I have my 24" connected to a 32" TV via DVI and have had no problems thus far.
When you open display preferences is the external display detected? If so, try switching between mirror and extended to see if it comes on.
The only other thing I could suggest is to try another VGA connector and/or cable. The fact the mouse goes erratic sort of points to there being the problem somewhere in the connection. You might want to try DVI if your monitor supports it.

External monitor for laptop not working

I just purchased this laptop and am trying to hook up an additional monitor. When I install the HDMI cable laptop screen goes dark and monitor screen remains dark. If I unplug the HDMI cable the laptop screen comes back. If i try to "adjust" the display in control panel i can only see the laptop screen. If I turn off external monitor and turn back on a message saying cable not attached is displayed before screen goes dark. I'm really in dark - need help. Thanks

The F4 was the solution for getting the laptop screen back, but i'm still unable to see anything on the external monitor. I have it recognized in the Control panel and all connections are correct. Could it be a setting with my NVIDIA GTX 950M video card? If so how do i change. By the way i checked the drivers for this and they are up to date. Now only half in the dark! LC

Using Mac OS on multiple monitor is great, but after removing external monitor (2nd monitor) usually windows position originally on the external monitor doesn't get re-positioned to default monitor. Is there any shortcut key or utilities that can reset wi

Using Mac OS on multiple monitor is great, but after removing external monitor (2nd monitor) usually windows position originally on the external monitor doesn't get re-positioned to default monitor. Is there any shortcut key or utilities that can reset wi

Got the "apple firewire ntsc" choice to show up even if grayed out and "missing" under "audio/visual" menus by recreating choices in Easy Setup under "final cut pro" MENU thank GOODNESS because I was reading horror stories on here about this under another thread with someone trashing preferences, reinstalling and the works and still not getting it to show up...on my search now for an analog/digital converter up at b&h...find it odd that the s video connector wouldn't show the crt monitor when I put both displays through the 3870...I switched it back to see if it worked again when only the one dell monitor display was there and there it is again mirroring the screen display on my desktop...just can't be seen as an "external monitor" in fcp...couldn't find anything specific in the shane ross threads to this. I'm sad the program doesn't just see the s video connection though the 3870 though my computer does fine and will query up at b&h in regard to what might be affordable as far as a digital/analog converter. It's also weird in itself that when I put the two dell monitors on the one card my computer no longer could see the s video crt connection...makes no sense. Will report in later as to what I discover up at b&h as I'm sure there's a world of people out there using this sony crt monitor still even into the upgrades with computers and software so I imagine therein lies the solution. Thanks again and I'll report in as to what hardware might be suggested for me.

External Monitors Dual Displays not supported

External Monitors Dual Displays not supported!
Yikes!
Why do I download BUGGY BETA OS? When will I learn ? DON't DO IT!
(sorry for shouting...)
There are no short cuts, no work arounds, no simple solutions...only updates
Please Apple code monkeys ..tear down this problem.
Thanks.
I feel better already .
--Marconi

Try this: Use the [√]Mirror displays oprions, choose your resolution, then desect the [ ]Mirror displays.
It shouldn't supossed to be like this, but until they send an update, this workarround will work.

How can I deactivate Adobe Acrobat 8 on a laptop with a monitor that does not work?

Or is there some work-around I can use? I got a new laptop and have reinstalled the program but I keep getting a pop-up that wants me to register it again. I have but it keeps popping up. I read in the user's guide for this version that "Note: If you want to install the software on a different computer, you must first deactivate the software on your computer: Choose Help > Activation > Deactivate." I figure that that is what the problem is. So now what do I do? It is a little hard to "choose" when the monitor is black.
As an added complication I am now getting an error message on the pop-up that tell me "A problem was encountered while trying to send information over the Internet." Help!!!
I am currently using a Sony Vaio T Series Ultrabook now with Windows 8. My old laptop was a Compaq and was using Windows XP Home Edition. It was about 10 years old.
Thanks in advance for your help.
Aimee

Can you plug in a remote monitor? You may have to use the Fn key with the screen icon typically along the function keys to change to the external monitor. If that works, then do what you need. You might also try putting the HD in another machine and see if it works there.

External USB HD does not work with HAL:

External USB HD does not work with HAL:
From the last 10 days the HAL auto-mount with ntfs-3g file system of my external hard drive does not woks.
But the manual mount procedure with the command mount -t ntfs-3g /dev/sdb* /mnt/XYZ works.
I've followed the instructions in the wiki: http://wiki.archlinux.org/index.php/HAL and the system has worked up to the last kernel or HAL update.
My fat32 usb-stick works without any problem.
If I try to open the device with KDE it appears an error popup wit this message:
TODO: have to rethink extra options
Error: kio_media_mount_helper
The log from the kernel.log is
Nov 6 22:03:16 myhost usb 5-1: new high speed USB device using ehci_hcd and address 4
Nov 6 22:03:16 myhost usb 5-1: configuration #1 chosen from 1 choice
Nov 6 22:03:17 myhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Nov 6 22:03:17 myhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 6 22:03:17 myhost Initializing USB Mass Storage driver...
Nov 6 22:03:17 myhost scsi6 : SCSI emulation for USB Mass Storage devices
Nov 6 22:03:17 myhost usb-storage: device found at 4
Nov 6 22:03:17 myhost usb-storage: waiting for device to settle before scanning
Nov 6 22:03:17 myhost usbcore: registered new interface driver usb-storage
Nov 6 22:03:17 myhost USB Mass Storage support registered.
Nov 6 22:03:22 myhost scsi 6:0:0:0: Direct-Access WDC WD32 00JB-00KFA0 0811 PQ: 0 ANSI: 0
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sdb: sdb1
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Attached SCSI disk
Nov 6 22:03:22 myhost sd 6:0:0:0: Attached scsi generic sg2 type 0
Nov 6 22:03:22 myhost usb-storage: device scan complete
and the error.log is
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Do you have some idea ....
Bye.

I have done the following:
Downloaded the patched hal version.
used makepkg in /abs/local/trunk/ to create a pkg for pacman
used sudo pacman -U pkgname to install it.
used sudo nano /etc/hal/fdi/policy/preferences.fdi to create the fdi file with the following content:
saved the file and removed my ntfs entryes from fstab and rebooted. and still there is no automount off ntfs partitions.
have i done something wrong?
br fjodork
WARNING: what follows is a guide of what did work for me, I'm still in an early stage of learning linux, so please correct me if anything of what follows is wrong/dangerous/stupid. As I said, this worked for me, it's not pretty, since I was learning each step on the fly and I'm sure there are better ways to do this.
So fjodork, you seem to have done the the necessary steps, though i couldn't get it to work until i first removed hal without dependencies
pacman -Rd hal
it will give you some warning about the dependencies, ignore it since we are reinstalling hal in a few steps.
First i tried to follow Raymano's link, obviously it showed me nothing in the browser so I thought it might be a broken link.
So I downloaded the source tarball from here http://hal.freedesktop.org/releases/hal-0.5.10.tar.gz
unpacked it changed the /tools/hal-storage-mount.c as per Milfadoodle's instructions.
at first I tried to compile directly from source, the process would finish without a glitch though after reboot nothing changed, as if hal weren't
installed, i guess there were issues with paths. anyway read on
Then repacked the source in tarball, copied it to /var/abs/extra/system/hal and modified the PKGBUILD as follows
makedepends=('pkgconfig' 'gperf')
options=('!libtool')
install=hal.install
source=(${pkgname}-${pkgver}.tar.gz #removed url so makepkg looks in the current directory for the tarball
hal
hal-policy.patch
cryptsetup_location.patch
hal-0.5.9-hide-diagnostic.patch
ntfs3g-valid-options.patch)
md5sums=('6641c30a27c00485c6accac5110ff911' # replace with md5sum of your package's sourceball (run md5sum filename)
'882f67668cb14a0a9e4a27ef22278027'
'5ba8b610aa9763a5f42b9f7cbd7a86ad'
then makepkg (i had to add --asroot, don't ask why
and finally pacman -U hal-0.5.10-1-i686.pkg
another reboot and everything worked without a glitch!:D (yeah i know i still haven't got rid of the reboot mentality )
I have also put the policy files as per the wiki instructions.
PS: I know this is a dirty way to getting things done but as i said, I'm just starting
If anyone could comment/correct/explain this post I'd be more than happy, the automount issue was bothering me for about a month now (you'll say why do I need ntfs in the first place? well, I only recently switched for Linux as my primary OS, these are some relics of the M$ era

External USB keyboard does not work with T60 after BIOS upgrade

External USB keyboard does not work properly with T60 after 2.26-1.07 BIOS upgrade.
It does the same with or without the docking station.
Anyone else bumped into this problem yet?
Has someone found any fixes for this?
t

Hi and welcome the forum!
Try uninstalling all USB hub devices from the device manager and reinstalling them again, particularly the keyboard's.
v2.26 is supposed to fix the issue according to lenovo:- http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-63024
Hope it helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

MY EXTERNAL SPEAKER PORT IS NOT WORKING for hp envy

MY EXTERNAL SPEAKER PORT IS NOT WORKING .WHEN I CONNECTED TO A EXTERNAL SPEAKER ,THERE WERE NO SOUND AUDIBLE.SO WHEN I DISCONNECTED THE CABLE FROM PORT,I WAS ABLE TO HEAR WITH THE IN BUILT SPEAKERS.EXTERNAL SPEAKER IS I GOOD CONDITION.I CHEKED WITH MY HEAD SET ALSO.IT WAS NOT AUDIBLE.MY LAP IS HP ENVY .KINDLY HELP

Hi ano87, welcome to the HP Forums. What is the model or product number? What version of Windows is installed?
Guide to finding your product number
Which Windows operating system am I running?
TwoPointOh
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

External hard drive is not working on airport time capsule even after 7.7.2 firmware update.

External hard drive is not working on airport time capsule even after 7.7.2 firmware update.
I have the latest Airpor Time capsule 2gb. I specifically bought it so that I could have an external hardrive set up to wirelessly house my itunes library and movies. When i connect the drive, all i get is that the disk needs to be repaired.
the drive can works fine when connected to the macbook pro and I have run the verify and repair features in disk utility. I have also reset the airport timecapsule as well following these changes and still no change.
The 7.7.2 update says that it addressed the usb issue of not showing the drives but there are still problems as I cannot get it to appear.
Please help.
Thanks

How is the hard drive formatted?
Have you tried using a powered USB hub with the drive when it is connected to the Time Capsule?
(The USB port on the Time Capsule is borderline as far as power is concerned....you may need to use a powered hub.....even if the hard drive has its own power supply)
If the drive is formatted correctly....and....it has ample power, it will "show up" when you open AirPort Utility, click Edit, then click the Disks tab at the top of the next window.
In the example below, my Time Capsule drive is named "Backups" and another drive named "WD Drive" is connected to the USB port on the Time Capsule.
You should see the name of your Time Capsule drive (named "Data" unless you have changed the name) and the name of the USB drive if you perform the same check.
What do you see?

External Hard Drive does not work with Lion

Hi
My External Hard Drive does not work with Lion this message appears:
NTFS-3G could not mount /dev/disk1s1
at /Volumes/My Passport because the following problem occurred:
/Library/Filesystems/fusefs.fs/Support/fusefs.kext failed to load - (libkern/kext) link error; check the system/kernel logs for errors or try kextutil(8).
the MacFUSE file system is not available (71)
can anyone help?

Hi,
See this Discussion:
https://discussions.apple.com/thread/3191198?start=0&tstart=0
Cheers,

IPS event monitor and reports not working

Dear after upgrading my IPS from E3 to E4  the event monitor and reports not working, can you please advice my to solve this issues

Hi All,
Filter settings below:
The filter works partially as I don't get alerts on the IPS itself.
Firewall LOG:
4          Feb 14 2014          15:33:22                              39715                    514          IPS requested to drop UDP packet from SOURCE_VLAN_NUMBER:/39715 to DESTINATION_VLAN_NUMBER:/514
IPS LOG (when enabled):
evIdsAlert: eventId=1352793300955167909 vendor=Cisco severity=low
originator:
    hostId: SSM02
    appName: sensorApp
    appInstanceId: 1192
time: Feb 14, 2014 15:33:22 UTC offset=0 timeZone=GMT00:00
signature:   description=IP Fragment Too Small id=1206 version=S212 type=anomaly created=20030801
    subsigId: 0
    sigDetails: Too many small IP fragments in datagram
interfaceGroup: vs0
vlan: 0
participants:
    attacker:
      addr: 172.x.x.x locality=OUT
      port: 39715
    target:
      addr: x.x.x.x locality=OUT
      port: 514
      os:   idSource=unknown type=unknown relevance=relevant
alertDetails: InterfaceAttributes: context="single_vf" physical="Unknown" backplane="GigabitEthernet0/1" ;
riskRatingValue: 50 targetValueRating=medium attackRelevanceRating=relevant
threatRatingValue: 50
interface: GigabitEthernet0/1 context=single_vf physical=Unknown backplane=GigabitEthernet0/1
protocol: udp
Our next step is to make a service policy exception on the firewall itself. We are also considering reloading the IPS device or at least the analysis engine.
Thanks for all your help so far. Any more suggestions are most welcome. I'll keep you up to date.
Regards
Mariusz

I am about to buy and iphone 4, its second hand and is in amazing condition. The only problem is that the 'wi-fi' button doesn't not work. I tried to click on it but nothing responds. Can this be fixed? Should i still purchase it?

I am about to buy and iphone 4, its second hand and is in amazing condition. The only problem is that the 'wi-fi' button doesn't not work. I tried to click on it but nothing responds. Can this be fixed? Should i still purchase it?

while you are with the person selling it to you, ask if you can do a complete restore of the software settings->general->reset->reset all
reboot the phone to factory settings and see if that fixes the problem. if not, i wouldn't buy it unless they are selling it to you for less than $50. wifi is crucial for keeping data low and using features like facetime

Encore WT8-A - External monitor doesn't not work

Similar Messages

Maybe you are looking for