Enhp4 - SFW5 - Business Fn activated but error in the job

Hello,
We installeld EHp4 successfully on our ERP 6.0 system . Business functions were activated using SFw5 and the activation job also completed succesfully.
In the job , I am seeing the following errors and no users reported for any issues so far.
Do we really need to concern about this error in the job
error:
Error Building the ENH TreeObject TYpe:XHObject Name VF_SFwS_SC_LV80CO01
Same error for few other objects as well
I saw this note 1162717 but not for Enhp4 and it says to ignore this error.
Any thoughts ?
Thanks !

> I saw this note 1162717 but not for Enhp4 and it says to ignore this error.
That note is valid for EHP4.
EHP4 includes Netweaver 7.01 - so that note is valid.
Markus

Similar Messages

My ipod touch has an "activation required" error and the slider won`t work

I have an itouch that is only 2.5yrs old and only gets occassional use. A week ago the slider wouldn't work; power switch didn't work; I reset and then tried (unsuccessfully) to restore to factory settings through itunes but encountered an error. At that point it appeared to be restored and I had use of original feature (clock, settings, etc) but I could not connect to WiFi and when I tried to connect to itunes again it did not recognize my device and now my Windows does not recognize my device. It tried to reset again but now I get an "activation required" error and the slider won`t work again.
I have read of other with the same problem but found no solution
Any help is greatly appreciated,
Thanks

Next try thge remaining items of
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

I replaced my Harddrive, Adobe CS2 askes for activation, but error code 24:24 comes up

After replacing my Harddrive, Adobe CS2 wants to by reactivated, by activating error code 24:24 is showing,
I was asked for phone activation, but several try´s I was told phonactivation is not supported anymore.
Can someone help me?

See the following for getting CS2 installed...
CS2: Error: Activation Server Unavailable | CS2, Acrobat 7, Audition 3 -
http://helpx.adobe.com/x-productkb/policy-pricing/creative-suite-2-activation-end-life.htm l

TS1292 My itunes card has been activated but when entering the code it is telling me it is not active

My itunes card has been activated but when I enter the code it says it isn't activated???

Hi ExtremeGamer1112,
Welcome to the Support Communities!
You are referencing the correct article to address this issue:
iTunes Store: Invalid, inactive, or illegible codes
http://support.apple.com/kb/TS1292
If you're still unable to redeem your code after verifying the characters in the code, you'll need to contact iTunes Store Support for help. You'll need to provide a digital image of the front and back of the gift card as well as the sales receipt for the purchase of the gift card.
Contacting iTunes Store Support
Go to the iTunes support page and select your iTunes country.
From the iTunes support page, choose Contact Support on the lower-left side of the page.
Follow the instructions to get iTunes Store support assistance.
Cheers,
Judy

Keep Program Active But Not on the Dock

I know that Skype is not an Apple program, but it, and other items (sometimes an Apple product) will become inactive when removed from the Dock. Can Skype, or other programs, remain active but not stay on the Dock, so that the visible (and active) icons that remain on a Dock are more manageable in their overall length?

hi,
today itself i faced the problem like this.
and my solution is .
i forgot to transport 1 previous request from quality to production.
thats shy my program running coorectly on quality but not on production and it is showing previous version as a active version.
just check for this scenario, or else retransport all request in a sequence. and then check it

SXI_CACHE throws error while activating; but error does not exist anymore

Hi everybody,
when I try to activate a BPM in sxi_cache. sxi_cache throws an error due to a step that does not exist anymore.
What can I do?
Thanks a lot
Regards Mario

Hello,
I am still getting the error . Plz suggest.
D:\psoft\PT8.52\setup>CBLBLD.BAT C: C:\TEMP
ASCII Cobol Compilations Proceeding
Creating Directory C:C:\TEMP
The filename, directory name, or volume label syntax is incorrect.
The filename, directory name, or volume label syntax is incorrect.
ERROR! Could not create compile directory(C:\TEMP)!
D:\psoft\PT8.52\setup>

Active Directory error message "the following object is not from a domain listed in the Select location forestB\username

Hello Community
    "forestA" is my forest it is a Windows 2008 Server Enterprise Edition
domain controller using Active Directory and the UI.
    In my forest ("forestA") trust relationship I created a "One-Way, Out-going"
forest trust with Forest-Wide authentication so that a different forest user(s) or
group(s) with a different admin in a forest named “forestB” can access the resources in my “forestA”
    But also forestB needs to create a "One-way, Incoming" forest trust so that
I can either add the user(s) or group(s) from “forestB” into to a "Global Security - Group"
in my "forestA" or I can
add user(s) as "domain user(s)" from “forestB” into my "forestA".
    The problem is that when I right click the global group in my forestA and then
properties, when I click "Members" and then the "Add" button when I type
"forestB\username" I get an error message from Active Directory stating:
    "the following object is not from a domain listed in the Select location
dialog box, and is therefore not valid: forestB\username".
    Am I doing something wrong when creating the one-way trust in my
“forestA” or is the one-way trust being created wrong by the other domain admin in the other “forestB”?
    Or could I possibly need to select "Change Domain" or "Change Domain Controller"
before adding the users or Groups to my forestA from forestB?
    That is why I am asking
how do you add an Active Directory user from one forest into another forest?
    Thank you
    Shabeaut

Hello Denis Cooper
    That is the end result.
    What I was trying to do was that I was trying to
bring in the user(s) and group(s) from “forestB” into
my “forestA” Global group.
    Later on I was going to add the user(s) or Global groups(s) that I brought into my dc in my forestA
into the domain local groups on my member servers in my forestA.
    So since the error message is:
"the following object is not from a domain listed in the Select location dialog box, and is therefore not valid: forestB\username".
Does your response
mean only Global group(s) from forestB not domain user(s) from forestB have
to been added to domain local groups in forestA?
Or is it also possible to add Global group(s) from “forestB” to Global group(s) in my “forestA” and if so
how without getting the above error message?
Thank you
    Shabeaut

My iMessage says it needs to be activated but i clicked the link and it already says its been activated...how do i get my imessage to turn on?

I just updated my 3GS to the 6 and everything has turned out well, but when i started signing up for the imessage i ran into some problems. I went through each step as it asked and then it sent a verification link to my email and thats where im lost at. I went to my email and clicked on the link and it says my account has already been verified. When i go back to settings and down to messages where you turn on imessage it says "waiting for activation. What is going on? thanks in advance

First thing to try is to reset your device. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider should one appear until the Apple logo appears. Let go of the buttons and let the device restart. See if that fixes your problem.

I have a Mac OS X 10.6.7 and Firefox 4. Other browser are easily connecting to the net but Firefox. It keep trying to connect to my wireless network but not doing the job. Please give some advice..

This happens when I first start the computer. Sometimes it connects to the wireless network, and during the day is fine.

user8744713 wrote:
I have downloaded Instant Client libraries (basic, SDK and SQL files, named instantclient-basic-10.2.0.4.0-macosx-x64.zip , instantclient-sqlplus-10.2.0.4.0-macosx-x64.zip and instantclient-sqlplus-10.2.0.4.0-macosx-x64.zip ) to Mac OS X 10.6.2 server and unzipped them as instructed in the manual here: http://download.oracle.com/docs/cd/B19306_01/install.102/e12121/inst_task.htm#BABJGGJH
Manual then instructs to run runInstaller command. This command however is not being recognized by the system (' No such file or directory' error is thrown) which to my opinion means one of two things: either command is misspelled in the manual or the command file that runs it is missing. I tried it with or without a dot and slash and in small case letters, nothing works.
When I installed similar libraries on Linux I had no problems but all was required there was to place libraries in the proper directory, no command was required.
Maybe same can be done here as well but I am not sure where to place some of the files. I see .h files that should go to /usr/include but see no .so files that on Linux go to /usr/lib. There are some files with .dylib and other .*lib extensions but I'm not sure if they should be copied to /usr/lib or not. And then there are some other files I have no idea what to do with.
Please help!!!No, you can't just drop a few files into a directory and have a working installation (well, I guess technically you could. But technically you could bail all the water out of Lake Superior with a teacup ...)
Sounds like you've covered PATH and current directory issues. What about permissions? What OS account are you using for this installation? (you should have created an account called "oracle" and made it's primary group "dba"). Does that account have execute permissions?
>
Thanks in advance!
Edited by: user8744713 on Mar 26, 2010 10:17 AM

Error In the activation process of DSO

Hi,
I am working with BI7, when i was activating data in DSO i got an error.The data has been loaded upto PSA and new table of DSO successfully but it is not loaded to active table at that time it is giving an error.
Please provide the solution for this.
Thanks,
Sarau.

Hi,
There are a couple of places where you can see the activation progress.
1) To start with SM37 job log > (give BI_PROCESS_ODSACTIVAT or BI_ODSA*)
and it should give you the details about the activation job. If its active make sure that the job log is getting updated at frequent intervals. If its completed check the log for ODS activation.
2) For very huge number of records SM37 job log may not get update frequently. In that case you have a workaround.
Go to contents > Active Data table > No. of entries > This will keep on increasing at frequent intervals.
3) SM66 > Get the job details (server name PID etc from SM37) and see in SM66 if the job is running or not. See if its accessing/updating some tables or is not doing anything at all.
4) Go to Activate button in Target > Request tab. Inside you can see a job log button. It will also show some log regarding the last activation.
5) If the Reporting icon has appeared near the request id in ODS. If it appears that may indicate that request is available for reporting
6) Check the request status in these tables.
Table RSICCONT table contains the requests that are actually loaded in a target.
Table RSMONICDP contains the request id of the fact table.
Table RSODSACTREQ contains information if an ODS is available for reporting/deleting inactive requests also possible.
Table RSODSACTUPDTYPE.
Thanks,
JituK

Why is there an error when activating custom wsp's (timer job) via SharePointUI?

We have created a Timer Job Project.
Before packaging wsp and deploying via PowerShell:-
1. If I set scope to Web and go to site features then I hit on Activate it gives error
(sayin to enable debug for error msg in web.config).
2. Similarly, if I set scope to Site, then if I go into site collection features and activate,
it give same error.
3. If scope is set to Web Application then the feature is activated by default (under
web app features), but cannot see the job under job definitions.
4. If scope is set to farm, then (under farm features) similar to above point no. 3
There is also error when deactivating features which are already activated when a package
is deployed. for example: web applicaiton feature.
Further, I cannot see the timer job under job defn unless it is scoped to SITE..
Why is this?
I donot get the issues when activating the features via PowerShell. Why is this?

Hi Nachiket Kamat,
When you are using web scoped or site scoped features to install the timer jobs, the account that does the scheduling must have write permissions to the configuration database of the server farm, usually, the identity of the application pool that is hosting
the SharePoint site does not have permissions on the configuration database, this is the account that is used when you activate the feature through the browser interface, this may cause the feature activated failed.
Another scenario that you met when you change the feature scope to web application, job definition cannot be seen, this may be caused by the feature receiver code, like if scope to web application, then get the web application from properties.Feature.Parent
as SPWebApplication, if you change the feature scope, then this also need to change to get the proper object.
Thanks,
Qiao Wei
TechNet Community Support

Error 13641 - The Subnet prefix must be between the starting and ending values

Hi All,
I can honestly say hand on heart that this is the first time I have ever asked for help in a forum in over 15 years but this is doing my head in..
I have a Sys Center 2012 R2 deployment.. VMM R2 up to RU3, Edge Cluster (2 hosts), Management Cluster (2 hosts), 2 x Production Compute Clusters (total of 20 hosts). I have a HA Network Virt Gateway deployed on the edge cluster.
All Hosts have the new DHCP install done and the RU3 SQL patch is completed as outlined in deployment manual.
Everything had been running fine for some time after RU3 update... I am experiencing an issue whereby I get the following error anytime I try and attach a NVGRE VM network to a VM, or when I try and migrate a VM with a NVGRE network attached to another
host.
Error (13641)
The specified subnet prefix must be between the starting and ending values for the range.
Starting value: 4
Ending value: 30
Recommended Action
Specify a suitable subnet prefix.
All subnets in the entire network are /24's so prefix isn't an issue.
I can successfully attach a standard vm network but get the above error when working with NVRGE networks..
Further to this, if I restart VMM the DHCP function to VM's with NVGRE networks doesn't get picked up until I trigger a change in config on the VM, then it will get IP and function as expected.
I have checked all logs, there aren't any errors that I can see.
get-netvirtualizationlookuprecord throws out VM's and PA's as expected, but again not until I manually interfere with the VM in question.
Have any of you come across this before?? I want to check before I go rebuilding the PA network entirely and having to cleanup all existing VM networks to do it..
Any help or guidance would be appreciated..
Cheers
Nathan

I have seen this message before, "specify a suitable subnet prefix".
In my case, the NVGRE policies were out of sync due to HW issues on several hosts.
Here's some steps in order to troubleshoot/fix:
run the following cmdlet: Get-SCVMHost | Read-SCVMhost -RunAsynchronously
Check for any errors in the job log that refers to "Network Virtualization".
If this doesn't help, a recycle of the VMM Management server should do a "hard refresh" of the NVGRE policies, and it might include a reboot of the nvgre hosts too.
This solved the case in my situation.
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )

Error message when deleting Business transaction: Activity in CRM

Hi All,
I am trying to delete a couple of Activities from CRM (Production system) and encounter two error message: "Enter a Business Partner" and "Administration header not found."
I have tried three ways to delete/archive the activity numbers in the system:
1) Using T code: CRMD_ORDER and then while in change mode - trying to delete the activities. When I tried this I get a warning message: "Enter a Business Partner" after I hit enter the warning: "Administration header not found." comes up and then takes you to the Easy access Menu after hitting enter.
2) I used T code SE38 to open program: "CRM_Order_Delete", here I entered the activity #s that I want to delete, the Activity Transaction type, select check box "Parallel" and then execute. I see a job log which says "Number of archived records = 3", the log shows that no records were deleted.
3) I have also tried archiving using T code SARA. But this also didn't seem to work. Here, I entered the Archiving object: CRM ACTON, then click on Preprocessing. I created a variant with the transaction type and activity numbers then set the start time to immediate and executed (F8) it. Even then I was not able to archive these activities. I did set the activities to status Complete.
Am I missing something? Appreciate your help.
Regards,
Ramesh
Edited by: Ramesh Nallabelli on Oct 9, 2008 9:55 AM

Received response from SAP support partner:
Please verify first if the issue is caused by badi implementation
of ORDER_SAVE badi. Please check method prepare and check_before_save.
Maybe inside your implementation the function crm_order_read is called
but that is not possible in case of deleting a document as document is
not available anymore.
If that doesn't work try this one:
Please check to see if you have a badi ORDER_SAVE method
CHANGE_BEFORE_UPDATE. Please deactiviate the ORDER_SAVE Badi and retestthe deletion.
This is how we resovled our issue - hope this helps someone else:
Check using T Code: SE80 to look for a BADI implementation which used BADI: ORDER_SAVE:
SE80-> Package: Z* (look for custom packages) -> Look under enhancements for any BADI Implementations which have used ORDER_SAVE (double click implementation and in the right pane look under Definition name).
Click 'Change' and deactivate this implementaiton. Now try to delete the CRM transaction. The error msg should not pop up now. Once deletion is completed reactivate this implementation.
This is just a work around. The problem lies in the code and the code within the implementation should be debugged and fixed so that this error message does not come up again.

Business Content Activation - run time error

Hi guys,
We were at plugin 2002.1. We installed PI 2002.2 and PI 2003.1 on top of it.
After the plug-in upgrade, we are at support pack 9 for SAP-BW and 13 for BI-Content. For aba and basis, we are at 620 and support pack 32.
As part of the regression testing after the 2003.1 plugin upgrade, we found out that the business content activation abends with the following run time error.
Runtime Errors SAPSQL_ARRAY_INSERT_DUPREC
Exception CX_SY_OPEN_SQL_DB
Looks like it is trying to insert into table RSOLTPSOURCEFIET and the row already is existing. I thought the activation process is supposed to update something if it is already out there.
If we just select the 'only necessary', the activation goes through ok, but if we select 'before and after in the data flow', we get this abend.
Any clues???
Best regards,
makaleem

Hi Seow,
This is how I resolved it. I looked at the ST22 closely and one of the messages indicated that the number range is missing in tran SNRO for an infoObject. I created an entry for that infoobject using SNRO and tried activation and it worked.
When we created an OSS for SAP to look into it, they recommended the following two things. I tried these two but it did not work. I am mentioning them below just in case they may help you.
1) Sometimes there is inconsistency in the content cache when trying to activate objects and we have to delete the repository cache. To delete the repository cache, go to RSA1 ---> Business Content -
> Extras ---> Delete Rep Cache
2) Execute SAP_DROP_TMPTABLES program for types 1,2,3 and 6.
If this helps, don't forget to assign points.
Abdul

BI Business content activation error

Dear Gurus,
I tried installing the business content InfoObject catalogs:
0FIGL_CHA01 (FIGL: Characteristics)
0FIGL_KYF01 (FIGL: Key Figures)
But the job is cancelled and the message is 'Transfer structure 0COMPANY_TEXT_BA does not exist'.I'm able to see all
the infoobjects in the InfoObject catalog 0FIGL_CHA01 are existing active. But few transfer rules are inactive and
I tried activating the transfer rules and getting the same error meassge 'Transfer structure 0COMPANY_TEXT_BA does not exist'. I tried as mentioned in the note:1077655 and still not able to fix the issue
Can you please help? I give full points.
Note: I did replication of the following before activating BI content on BI side:
0BUS_AREA_ATTR           (no issue with this)
0BUS_AREA_TEXT          (no issue with this)
0CHRT_ACCTS_ATTR     (no issue with this)
0CHRT_ACCTS_TEXT     (no issue with this)
0COMPANY_TEXT          (inactive transfer rules)
0COMP_CODE_ATTR          (inactive transfer rules)
0COMP_CODE_TEXT          (inactive transfer rules)
0GL_ACCOUNT_ATTR     (inactive transfer rules)
0GL_ACCOUNT_T011_HIER     (inactive transfer rules)
0GL_ACCOUNT_TEXT      (inactive transfer rules)
Thanks in advance
Seenu

One reason for you Inactive Transfer structures could be because some of the Objects in BW are inactive or not installed.
There are programs in SE38 which re-activate InfoObjects/ InfoSources/ Update Rules etc in Mass put in ACTIVATE
Also when you did a replication on the Source System to pull the datasources check that the Datasource is there. You need a datasource in order to have an InfoSource attached to it.

Enhp4 - SFW5 - Business Fn activated but error in the job

Similar Messages

Maybe you are looking for