Enlightenment Problem

I am new to Arch, and DEs in general, and I have having a problem starting Enlightenment.  I have installed X as per the beginner's guide, and I have got it to work.  But when I try to start Enlightenment, I get an Enlightenment Error:
Enlightenment cannot initialize the FDO desktop system.  Perhaps you are out of memory?
I know that my laptop (Sony Vaio VGN-Z530N) meets all the necessary requirements to run it, so it can't truly be a lack of RAM.
~/.xinitrc: http://paste.pocoo.org/show/325700
/var/log/Xorg.0.log: http://paste.pocoo.org/show/325699
/var/log/Xorg.0.log.old: http://paste.pocoo.org/show/325695
For some reason, I don't have /etc/X11/xorg.conf, which might be the cause of my problems.  But I can start X and view the twm DE no problem by commenting out the appropriate lines in the .xinitrc file.  Where should I go from here?

I appreciate the help, but I am still having problems. 
If I edit ~/.xinitrc to be like this: http://paste.pocoo.org/show/326394 then I get the same 'Enlightenment cannot initialize the FDO desktop system.' error.
If I edit ~/.xinitrc to be like this: http://paste.pocoo.org/show/326395 then something is displayed, but it looks almost exactly like twm, except there aren't blue-green top borders to the windows.  And if I try to copy an Enlightenment theme (a .edj file got from the the e17-themes in the AUR) to the ~/.e/e/themes folder, nothing changes.
Finally, If I edit ~/.xinitrc to be like this: http://paste.pocoo.org/show/326399 then I get the same 'Enlightenment cannot initialize the FDO desktop system.' error.
Could it that I created my .xinitrc file incorrectly?  After I installed xorg with pacman, there was no .xinitrc file in my home directory.  I copied (and renamed) the /etc/X11/xinit/xinitrc file to my home directory.  That didn't seem right, but I couldn't think of anything else to do.

Similar Messages

  • [Enlightenment E17] Problems with EFM after last Update [solved]

    Hello Folks!
    I'm having some very ugly problems with my Enlightenment E17 Desktop after the last full system upgrade. This problem has already been reported to the German Arch Linux community, but no response yet, but I can't figure out that nobody else troubles the same probs.
    This is the following what I get when running pacman -Ss e17-svn
    community/e-svn 42849-1 (e17-svn)
    Enlightenment window manager DR17 (aka e17)
    community/e_dbus-svn 42682-1 (e17-libs-svn e17-svn)
    dbus abstraction layer for e17
    community/ecore-svn 42854-1 (e17-libs-svn e17-svn)
    Ecore is an abstraction layer for e17
    community/edje-svn 42794-1 (e17-libs-svn e17-svn)
    A graphical design and layout library based on Evas
    community/eet-svn 42851-1 (e17-libs-svn e17-svn)
    A data storage and compression library
    community/efreet-svn 42759-1 (e17-libs-svn e17-svn)
    freedesktop.org specifications for e17
    community/eina-svn 42822-1 (e17-libs-svn e17-svn)
    E17 file chunk reading/writing library
    community/embryo-svn 42739-1 (e17-libs-svn e17-svn)
    implementation of a C like scripting language for e17
    community/evas-svn 42855-1 (e17-libs-svn e17-svn)
    A hardware-accelerated canvas API for X-Windows
    The problems that occur to me are following: I'm using EFM as file manager. It's not the best one, but it fits into the E17 concept - simple, lightweight, fast - and thats what I like. But, after the latest update, when I click a folder on my desktop, EFM now comes up in a stupid very tiny window. The window is so small, that I need to resize it every time to see any content. Before the update, everything worked fine, the EFM windows came up as they should.
    Another problem I'm having with some applications, e.g. the Okular-Viewer, is that I'm not able to size down the window - it is always in full screen, and there's no chance to move it up (even not on the desktop preview widget) to move it down. Okular is always 100% filling my screen (over the height, only), and I'm not able to size it down. In the previous version, I didn't got this problems.
    My question is now: is there any way to install the previous Enlightenment E17 packages? They where much better that this one... or will another update come out soon??
    Thanks in advance for any help, any help is appreciated!
    beachcoder
    Last edited by beachcoder (2009-10-09 09:04:21)

    Have you tried starting with a clean config and the default theme, it helps sometimes after big code changes?
    If that doesn't help...
    beachcoder wrote:My question is now: is there any way to install the previous Enlightenment E17 packages? They where much better that this one... or will another update come out soon??
    If you find some mirror which keeps outdated packages that should not be a problem. Be sure to downgrade all of e17 packages (also some packages were deprecated and thus removed from the server during the last upgrade so you'd need to have those as well. You may still have those on your system though)
    About a quick update, depends if Ican replicate it and if there is an easy fix. These things happen now and then with pre-alpha software when they do make major code changes.  I try to test every update locally before putting it live but I of course can't test every single feature.
    Last edited by pressh (2009-10-09 06:03:31)

  • Newbie problem - enlightenment: No such file or directory

    Hi, I'm new in Archlinux and I've found a ridiculous problem after install enlightenment.
    I have put:
    exec /opt/e17/bin/enlightenment_start
    on ~/.xinitrc, but drops the error:
    -bash: /opt/e17/bin/enlightenment_start: No such file or directory
    but the file IS there!! I can see it in the directory, and I can tab the command, but bash don't found it...
    I tryed others binaries in the directory and works, but only the *-config, the others don't work, no one.
    Please, anyone know why can happen this?? I'm getting mad trying to find a solution...
    PD.: Sorry for my poor english ^_^

    Sorry for the mistake
    [terseus@terseus-pc ~] ls -l /opt/e17/bin/enlightenment_start
    -rwxr-xr-x 1 root root 8908 Mar 11 14:55 /opt/e17/bin/enlightenment_start
    I think the permissions are right, I tryed with root but doesn't work.
    PD.: The webpage of Archlinux is really great! The site and the forum work perfectly even from links

  • Enlightenment 0.18.2-1 problems

    After upgrading from e17 to enlightenment-0.18.2-1 there are few problems:
    1. Icons from systray have disappeared. There are no more pidgin and gnubiff icons.
    2. There was disabled composit mode and after upgrade fullscreen xterm becomes non-fulscreen after switching desktops. I have to switch on some animation to stay in fullscreen xterm after desktop switching.
    Is any way to fix this behavior ?
    B.t.w. Does enlightenment have an mail-check aplet the same with gnubiff (imap with ssl and IDLE or NOTIFY support) ? I need something like gnubiff but workable. Gnubiff seems to be dead project:-(.

    Scimmia wrote:
    1. Right click on the systray, go to Systray | Settings and enable xembed.
    2. Not sure what you mean by "there was disabled composit mode". I'm in E19 with a compositor rewrite, so I can't test, maybe someone else can help more with this one?
    There is a mail module as part of the e-extra-modules, but I've never used it. Worth a try.
    1. Oh... You have save me a lot of time with "xembed" check-box. Thanks. Now gnubiff seems works more stable then before I switched xembed on.
    2. I'm also not shure about it because I've translate it back to english from russian :-). So it can be composition mode or compositor mode or ... It is something like this: settingd -> screen -> virtual work places and here there is animation of <something (switching between work places)>. There are Blend, Diagonal, Grow, Pane and other variants. When I choose "Disable" then my fullscreen xterm becomes non-fulscreen when I switch back to work place with this fullscreened xterm -- it is annoying ...
    Where can I find e-extra-modules ? There is no such package in AUR.

  • Problems with Enlightenment

    Hey,
    I'm a newbie to Arch Linux but it sounded cool and like something I wanted to try.
    It took me a little to get some things figured out, but I got my Arch Linux somewhat working and Enlightenment installed as my WM.  However when I try and lauch a lot of the programs that came with the WM I get an error message saying:
    Application run error
    Enlightenment was unable to run the application:
    xterm
    The application failed to start.
    Also, an unrelated question, I installed firefox using pacman from a virtual console, but all the tabs and menu bar look super ugly like windows 98 or something.. why?
    Thanks

    I don't think that is my problem.  My problem is that when I try and run most of the applications that came with E17 I get that error.  I was using the application xterm as an example, its listed under the applications > system > XTerm (Terminal). 
    The applications that don't work are the Avahi SSH and VNC Server Browsers, MPlayer, Avahi Zeroconf Browser, and XTerm. 
    The only ones that do seem to work are the Elementary Test application and the Enlightenment File Manager.

  • RH6/O8i install problem? Enlightenment patch.

    http://www.redhat.com/corp/support/errata/rh60-errata-
    general.html#enlightenment
    null

    Cliff Kotnik (guest) wrote:
    : Scott Fraser (guest) wrote:
    : : When applying the patch on a fresh EE install on Redhat 6 I
    am
    : : getting a link error at the end that says it can't find the
    : : ordsdo8 library:
    : : >>
    : : /usr/bin/ld: cannot open -lordsdo8: No such file or directory
    : : <<
    : Yes I get that also. Here is the full list of warnings/errors
    I
    : get from the patch:
    : mv: /opt/oracle/product/8.1.5/bin/names: No such file or
    : directory
    : gmake: [inames] Error 1 (ignored)
    : mv: /opt/oracle/product/8.1.5/bin/namesctl: No such file or
    : directory
    : gmake: [inamesctl] Error 1 (ignored)
    : mv: /opt/oracle/product/8.1.5/bin/tnslsnr: No such file or
    : directory
    : gmake: [itnslsnr] Error 1 (ignored)
    : mv: /opt/oracle/product/8.1.5/bin/lsnrctl: No such file or
    : directory
    : gmake: [ilsnrctl] Error 1 (ignored)
    : /usr/bin/ld: warning: type and size of dynamic symbol
    `sskgslgf'
    : are not defined
    : /usr/bin/ld: cannot open -lordsdo8: No such file or directory
    : collect2: ld returned 1 exit status
    : gmake: *** [opt/oracle/product/8.1.5/rdbms/lib/oracle] Error 1
    The same. And i solved it moving to SuSe 6.2 with their patch
    file. But it seems that RedHat 6.1 is able to solve that
    problem. Don't know. Never tried.
    Surely you can do nothing to overcame that errors with RH6
    -Stefano
    null

  • [SOLVED] AUR's enlightenment-git installation problem

    Hello
    I was attempting to install enlightenment-git from AUR, but I get an error during efl-git. I made a system update before, so I had the latest base-devel tools. Any thoughts?
    CC modules/ecore_evas/engines/wayland/modules_ecore_evas_engines_wayland_module_la-ecore_evas_wayland_common.lo
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c: In function '_ecore_evas_wl_common_cb_window_configure':
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:309:20: error: 'fw' undeclared (first use in this function)
    nw -= fw;
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:309:20: note: each undeclared identifier is reported only once for each function it appears in
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:310:20: error: 'fh' undeclared (first use in this function)
    nh -= fh;
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:191:24: warning: variable 'prev_full' set but not used [-Wunused-but-set-variable]
    Eina_Bool prev_max, prev_full;
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:191:14: warning: variable 'prev_max' set but not used [-Wunused-but-set-variable]
    Eina_Bool prev_max, prev_full;
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:190:20: warning: variable 'orig_h' set but not used [-Wunused-but-set-variable]
    int orig_w = 0, orig_h = 0;
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:190:8: warning: variable 'orig_w' set but not used [-Wunused-but-set-variable]
    int orig_w = 0, orig_h = 0;
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c: At top level:
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:319:4: error: expected identifier or '(' before 'if'
    if (prev_full != ee->prop.fullscreen)
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:322:4: error: expected identifier or '(' before 'if'
    if (ee->prop.fullscreen)
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:333:4: error: expected identifier or '(' before 'if'
    if ((ee->x != ev->x) || (ee->y != ev->y))
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:336:4: error: expected identifier or '(' before 'if'
    if ((ee->req.w != orig_w) || (ee->req.h != orig_h))
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:339:4: error: expected identifier or '(' before 'if'
    if ((prev_max != ee->prop.maximized) ||
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:343:4: error: expected identifier or '(' before 'return'
    return ECORE_CALLBACK_PASS_ON;
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:344:1: error: expected identifier or '(' before '}' token
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:1526:1: warning: '_ecore_evas_wayland_resize_edge_set' defined but not used [-Wunused-function]
    _ecore_evas_wayland_resize_edge_set(Ecore_Evas *ee, int edge)
    ^
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c: In function '_ecore_evas_wl_common_cb_window_configure':
    modules/ecore_evas/engines/wayland/ecore_evas_wayland_common.c:317:6: warning: control reaches end of non-void function [-Wreturn-type]
    ^
    Makefile:20441: recipe for target 'modules/ecore_evas/engines/wayland/modules_ecore_evas_engines_wayland_module_la-ecore_evas_wayland_common.lo' failed
    make[4]: *** [modules/ecore_evas/engines/wayland/modules_ecore_evas_engines_wayland_module_la-ecore_evas_wayland_common.lo] Error 1
    Makefile:25586: recipe for target 'all-recursive' failed
    make[3]: *** [all-recursive] Error 1
    Makefile:9090: recipe for target 'all' failed
    make[2]: *** [all] Error 2
    Makefile:1728: recipe for target 'all-recursive' failed
    make[1]: *** [all-recursive] Error 1
    Makefile:1230: recipe for target 'all' failed
    make: *** [all] Error 2
    Last edited by Linoman (2014-01-20 09:22:00)

    Assuming you don't need wayland, you could try and comment/delete those lines in PKGBUILD:
    --enable-wayland-clients \
    --enable-wayland-egl

  • LG Enlighten - Backup Assistant Problems?

    Every night when my LG Enlighten's Backup Assistant does it's scheduled backup, my phone doesn't lock up when I press the sleep button and every time I hit the "home" button, it doesn't work (it just stays on whatever screen it was on). The only way to get off the screen is by hitting the back button. 
    This has happened every night for awhile now and the only way to fix it is to shut down the phone and turn in back on.
    Is there any possible way to fix this without having to restart my phone every time?

    @Rainseclipse that’s not good about your phone. I can help to get this resolved. First, with the phone not locking up, does this only happen when Backup Assistant is backing up? Second, the home button issue, does that happen all the time or only when backing up? Do you have a lot of 3rd party apps on the phone? Have you tried to delete some apps from the phone? Sometimes 3rd party apps can cause adverse functionality on the phone. Please answer these questions so I can help you get this issue resolved. Thanks.
    SammuelP_VZW
    VZW Support
    Follow us on Twitter @VZWSupport

  • SB X-Fi Extreme music problems, enlighten me please!

    Hello to all! I'm a Creative sound cards user since 90's. Satisfied yes,but i would ask for a little help over here now.
    I have the extreme music pci, not much of a new card i know, but i like the way it sounds through my marantz av amplifier very much. I have used that card with my previous 2 pcs without any issues. Last year i bought an asus p7h55d-m evo motherboard, intel core i5 66 dual core cpu, 2 corsair memory (i can't recall the model right now) sticks each one of 2 gb ram, amd 5770 with GB graphics card, TB WD 00fals hard disk dri've and put them together in Thermaltake HTPC case with a vfd display (imon). I have other devices too but i don't know if it would do any difference to mention.
    Motherboard has onboard integrated sound chipset which is disabled (though it should not be a problem enabled), graphics card too (through hdmi). I have ONLY PCI slot where i installed the extreme music. My problem is that even if the latest creative driver for win7 64 bit is succesfully installed and everything looks just fine (no conflicts, resources are ok) i here a very low volume sound output from my speakers. I need to raise the volume to 80% to barely listen to what's played from the x-fi. Before some months the first time i installed the card it worked. Looks like something changed in win7 and doesn't let the card to function correctly. I need your help here as this might be my last chance to figure out the problem before i quit trying with that card. I may buy a new model but i'm not sure what's wrong and if the new one will work.

    Maybe you plugged the cables too slacky, reconnect the cables that connect the hardware. Alternati'vely click on the volume in the windows tasklist on the right and select the mixer ... raise everything there.. The output should be enormeus. (sorry for my bad english)
    too late but better than nothing.

  • HT201272 hi all, I am having trouble downloading 2 music videos. I keep getting the download error 8008. Can anyone enlighten me on how to work around the problem.

    Hi guys, I'm havinh trouble downloading 2 music videos. The download starts then stops before it gets going and gives me an error code, 8008. Can anyone help please.

    Try the troubleshooting for that error number on this page : http://support.apple.com/kb/TS3297
    "Error -50," "-5000," "8003," "8008," or "-42023"
    These alerts occur due to timeouts or conflicts trying to write a file during download.
    If you encounter this issue while accessing iTunes Store:
    See iTunes 9: "One Moment Please" or "Error (-50)" message when accessing iTunes Store
    If you encounter this issue while while downloading something from the iTunes Store:
    Delete your iTunes Downloads folder, located in:
    Mac OS X:
  ~/Music/iTunes/iTunes Media/Downloads   Note: "iTunes Media" may appear as "iTunes Music. Also, the tilde (~) refers to your Home directory.
    Windows Vista:
  \Users\username\Music\iTunes\iTunes Media\Downloads\
    Windows 7:
  \Users\username\My Music\iTunes\iTunes Media\Downloads\
    Windows XP:
  \Documents and Settings\username\My Documents\My Music\iTunes\iTunes Media\Downloads\
    After locating your iTunes Downloads folder:
    Quit iTunes.
    Delete the Downloads folder on your computer.
    Open iTunes.
    Choose Store > Check for Available Downloads.
    Enter your account name and password.
    If you encounter this issue while while downloading Digital Copies using Windows:
    Use MSCONFIG (directions for Windows XP and Windows Vista/Windows 7) to disable conflicting software.
    If using MSCONFIG steps resolves the issue, you may want to use the System Configuration Utility to turn on the third-party System Services and Startup Items one at a time (restarting your computer after turning on the item or items) to identify which System Service or Startup Item is causing the conflict.
    You can turn all of them back on by selecting the Normal Startup option under the General tab of the System Configuration Utility window, but please note that this may cause the issue to reoccur.
    If you are able to isolate the issue to a particular third-party software, you may wish to contact them to let them know of the conflict.

  • Problem with JPanel and/or Thread

    Hello all,
    I have the following problem.
    I have a JFrame containing to JPanels. The JPanels are placed
    via BorderLayout.
    JPanel #1 is for moving a little rectangle (setDoubleBufferd), it is
    a self defined object extending JPanel.
    The paint methon in JPanel #1 has been overwritten to do the drawings.
    JPanel #2 contains 4 JButtons, but they have no effect at the
    moment. It is an "original" JPanel.
    The class extending JFrame implemented the interface Runnable and
    is started in its own thread.
    After starting the programm everthing looks fine.
    But if I press a Button in the second JPanel this button is painted in
    the top left corner of my frame. It changes if I press another button.
    Any help would be appreciated.
    Thanks.
    Ralf

    I have a JFrame containing to JPanels. The JPanels are
    placed
    via BorderLayout.The type of Layout does not seem to be relevant
    >
    JPanel #1 is for moving a little rectangle
    (setDoubleBufferd), it is
    a self defined object extending JPanel.
    The paint methon in JPanel #1 has been overwritten to
    do the drawings.
    JPanel #2 contains 4 JButtons, but they have no effect
    at the
    moment. It is an "original" JPanel.
    The class extending JFrame implemented the interface
    Runnable and
    is started in its own thread.
    After starting the programm everthing looks fine.
    But if I press a Button in the second JPanel this
    button is painted in
    the top left corner of my frame. It changes if I press
    another button.
    I noticed you solved this by painting the whole JFrame.
    Yeh Form time to time I get this problem too......
    Especially if the screen has gone blank - by going and having a cup of tea etc -
    Text from one Panel would be drawn in another.. annoying
    At first it was because I changed the state of some Swing Components
    not from the Event Thread.
    So make sure that your new Thread doesn't just blithely call repaint() or such like cos that leads to problems
    but rather something like
    SwingUtilities.invokeLater( new Runnable()
       public void run()
          MyComponent.repaint();
    });However I still get this problem using JScrollPanes, and was able to fix it by using the slower backing store method for the JScrollPane
    I could not see from my code how something on one JPanel can get drawn on another JPanel but it was happening.
    Anyone who could totally enlighten me on this?

  • Transition Problems in Full Screen View

    Hi.
    I've created a Powerpoint presentation on the Bayeux Tapestry which I now want to convert to a PDF document so that I can add multimedia.
    My Powerpoint presentation features photographs of a section the tapestry with each photograph placed on a separate slide. I've used the Powerpoint 'push left' transition to create a panoramic effect which creates the illusion that the tapestry is being scrolled from right to left  as the viewer clicks through the presentation. It all works very well in Powerpoint as the slides butt up against each other in transition without any 'seam' between them.
    I thought I could simply replicate the effect in Acrobat 9 by converting the presentation to PDF and selecting the 'push left' transition from Advance/Document Processing options then launching the document in full screen view. However, I've found that using a push left transition in Acrobat creates wacking great gaps between the pages as they scroll right to left: this absolutely ruins the whole effect.
    As you can probably tell, I'm pretty much a newbie with Acrobat 9 (but not with other Adobe applications) and I can't work out for the life of me how to get around this problem. Is there someting simple that I'm overlooking on the full screen view options or perhaps in the Powerpoint conversion settings or do I have to start adjusting resolutions etc? Or maybe it's just the nature ofthe beast (do hope not)?
    I'd be very grateful for any enlightenment or advice.
    PS: Forgot to mention the Powerpoint was created in default landscape layout and hence so is the PDF.

    Do you have the PDF version to fill the full screen and not leave borders? If you print to PDF (not create PDF), then a margin is added by default (as when you print to paper). The border can be reduced to 0, but that is an extra step with the print. As I recall, the PDF Maker (create PDF) does not include the margins. Thus the whole margin bit may be the issue.

  • Wierd problem regarding JInternalFrames and OUTLINE_DRAG_MODE

    Hi there,
    I'm currently experiencing a strange problem regarding the use of a JDesktopPane and JInternalFrames.
    Code may look as this, its a random Example as I encounter the same results no matter how I construct the Frame and so on:
    public class Example extends JFrame{
        public Example() {
            this.setTitle("Example");
            this.setPreferredSize(new Dimension(800,800));
            this.setLocationRelativeTo(null);
            this.setDefaultCloseOperation(EXIT_ON_CLOSE);
            JPanel contentPane = (JPanel) this.getContentPane();
            contentPane.setLayout(new BorderLayout());
            JDesktopPane dp = new JDesktopPane();
            dp.setDragMode(JDesktopPane.OUTLINE_DRAG_MODE);
            contentPane.add(dp, BorderLayout.CENTER);
            this.setVisible(true);
            JInternalFrame f = new JInternalFrame("not so cool", true);
            f.setPreferredSize(new Dimension(400,400));
            f.pack();
            dp.add(f);
            f.setVisible(true);
        public static void main(String args[]){
            Example ex = new Example();
    }So, I'm currently using Netbeans and when I'm running any application/project with those settings from inside the IDE
    theres absolutley no problem. As soon as I'm running the Jar file, the drawing of the "outlines" while resizing the InternalFrame
    is kinda laggy and choppy as hell. I spent 2 hours of googling now and I still got no idea why thats the case, so I hope anyone
    here can enlighten me.
    The Java version installed is 1.6.0_10
    regards, me

    AndrewThompson64 wrote:
    (shrugs) Maybe the IDE is using -Dsun.java2d.d3d=false? In any case, very few people around here provide support* for IDEs.
    * Read that as 'speculate on why an IDE does it different - why it works in an IDE'Sir, seems like you got the point, I wasnt familiar with those command line options for the VM before, regarding Graphics options.
    Working fine as soon as I disable D3D. Should've come to that myself but oh well -.-.
    Thanks guys!

  • Active Directory Server Problem

    Hi All,
    This mail Seeks to get help from people who have worked with Active Directory Server.
    The following is our Current scenario.
    We are in the process of establishing an SSL connection to Active Directory Server from java environment(a standalone class) in Windows 2000.
    1.Active Directory Server is installed in an independent Win 2k machine.
    2.SSL is enabled in the Active Directory Server Machine by installing the Enterprise Root Certificate.
    3.Microsoft High Encryption pack is installed in both the client and the Server(AD)
    4.The .cer file from the AD machine is imported in to the Client's keystore(cacerts) using the keytool utility.
    5.The AD m/c is part of a domain named "rsa" and client m/c is part of the domain named "cts"
    With the above setup,The following code tries to Establish an SSL context to the AD through JNDI.
    Hashtable env = new Hashtable();
    env.put(Context.INITIAL_CONTEXT_FACTORY,"com.sun.jndi.ldap.LdapCtxFactory");
    env.put(Context.PROVIDER_URL,"ldap://blr03srv1.rsa.com:636");
    env.put(Context.SECURITY_PROTOCOL, "ssl");
    env.put(Context.SECURITY_AUTHENTICATION, "simple");
    env.put(Context.SECURITY_PRINCIPAL,"CN=Administrator,CN=Users,DC=rsa,DC=com");
    env.put(Context.SECURITY_CREDENTIALS,"password");
    try{
         DirContext ctx = new InitialDirContext(env);
         ctx.close();
    }catch (Exception e){
         e.printStackTrace();
    When we try to run this Client we are facing a SSLHandShakeException with a message saying "No trusted certificate found".
    As far as we know the .cer file is successfully imported in to the cacerts which is used by the J2SE as the default keystore.
    Hence we ran out of ideas,as we think that there could be some other issue which is causing this problem.
    We are looking forward to get inputs from AD enlightened people to Solve this issue
    Thanks in Advance,
    Manivannan.A

    I had problem the same and still I did not obtain to decide it, if for perhaps obtaining he passes me the solution.
    thank's
    Fernando Queiroz Fonseca
    Graduando em Engenharia El�trica
    Universidade Federal de Uberl�ndia
    http://www.fernandoqueiroz.com.br
    email : [email protected]

  • Weird Problem -- Mouse Freezes when I plug in my camera

    Hey guys,
    I've been combing the forums and have found some similar issues reported but no solutions to speak of.
    Here's the deal:
    My camera -- Minolta Dimage A200 -- I've had it for 2 months now and have connected it to my iMac G4 800 mhz dozens of times without incident.
    Now..about 1 week ago I upgraded to Tiger. Two days ago my wife connected the camera and uploaded a few pictures without having any issues. Although, I'm more than certain that she wouldn't have ejected the camera properly.
    Yesterday I tried to connect the camera and this is what happened:
    As soon as I connect the usb cable with the camera attached to it my keyboard and mouse go dead. It doesn't matter what port I use...the same thing happens. If I unplug the camera and then unplug and replug the keyboard and mouse they spring back to life. If I plug in just the usb cable everything is fine. If the camera is attached(on or off) the keyboard/mouse go dead.
    I read some speculation about the port not having enough power so I tried to plug the camera into my Powered usb hub. This didn't work either. My mouse didn't go dead but the light at the port I plugged into went dark and the computer was none the wiser as to the camera's presence...not good.
    I have to believe that my problem has something to do with:
    1. Upgrading to Tiger
    and
    2. Not ejecting the camera properly on first use with tiger.
    Any help would be appreciated.
    BTW...I also tried formatting my memory card on the camera.

    Hmmm...
    A bit disappointed that no one has come to my rescue.
    I went out and bought a CF media reader today and it circumvents the problem nicely...for $29.99 Canadian.
    It's actually nice to use the reader and not have to worry about the camera and cables and what not.
    Still...I want to know what the problem is.
    I'll keep checking the thread in hopes of enlightenment.

Maybe you are looking for

  • How do I implement Drill UP functionality in my Request

    Currently when I Drill-down from parent ( Hierarchy1_id) , request shows up all its childrens ( Hierarchy2_id). How do I rollup to parent again ?

  • Edit Multiple Images in photoshop cs5

    I am trying to apply the same affects thru a action to about 50 some odd photos. I don't want to go thru them individually so how do you do them all at once? Can you convert them to smart objects then apply the action? I tried this but once i want to

  • How do i get app w/o using credit card?

    I would like to know how to get apps without using a credit card.  I do not use credit cards on mobile devices and I wouldn't want to charge $0.99. Can they be billed to your phone bill some how or some other thing set up?

  • Need a FM which returns the last modified date& time

    Hi, Kindly Suggest me if any Function Module is there which returns the last modified date& time for tables HRP1000 and HRP1001. Rgds Kishor.C

  • Downloading Purchased Products

    I purchased Adobe Photoshop Elements 10 and Adobe Premiere Elements 10 6 months ago and am trying to download it in my new computer that does not have a disc drive.  I can't believe it is so hard to figure out how to get this done!  Can anyone help?