Enterprise DNS servers are not responding when using Windows NLB with Direct Access 2012

Hi
We have installed Direct Access 2012 as one server installation:
- Two network cards. First one in DMZ and second one in internal network
- Two consecutive IP addresses configured in DMZ because of Teredo
- PKI because of Win7 Clients IPSec
- Our corporate network is native IPv4 so we use DNS64/NAT64 and DA-server is configured as DNS
- DA-servers are VMWare virtual machines
One server installation works fine and now we want to use Windows NLB as load balancing. NLB installation goes fine too,
but problem is DNS. If we still try to use DA-server as DNS there comes error message below
None of the enterprise DNS servers 2002:xxxx:xxxx:3333::1 used by DirectAccess clients for name resolution are responding. This might affect DirectAccess client connectivity to corporate resources.
When trying to configure DNS using Infrastructure access setup, DNS cannot be validated when using DA-servers DIP or cluster VIP. Only domain local DNS looks to be ok but those have no IPv6 addressess. So how DNS should be configured when using multicast
NLB?
Tried to remove name suffix then adding again => Detect DNS server => DA-server IPv6 address found => validate => The specified DNS server is not responding...
Then tried to ping detected address => General failure
NLB clusters are configured as multicast and static ARPs are configured too. Both clusters can be connected from those subnets as they should be.
Any clues how to fix this?
~ Jukka ~

Hi,
Your question falls into the paid support category which requires a more in-depth level of support. Please visit the below link to see the various
paid support options that are available to better meet your needs.
http://support.microsoft.com/default.aspx?id=fh;en-us;offerprophone
Regards,
Mike
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Similar Messages

Help topics are not displaying when using Windows 8/IE 10

I have a WebHelp system created in RoboHelp 7. When opening that Help from our application using Windows 8 with Internet Explorer 10 and allowing blocked content, the Help topics do not display in the right pane when clicking a topic from the Contents in the left pane. Below are the steps:
1. Open the Help system from the Help menu within the application.
2. The Allow Blocked Content displays and I allow it.
3. The Help opens and if I click a topic from the TOC in the left pane, the topic doesn't display in the right pane.
A workaround we found was to widen the left pane and the topic then displays. Also, if you don't allow blocked content, this issue doesn't happen. However, I need to allow blocked content in order for PDFs within the Help to open properly and also because the Search doesn't display without allowing blocked content.
We also tested this with a Help system that was created using Robohelp 9 and have the same issue. I'm wondering if RoboHelp 10 would solve this problem.
Does anyone know if IE 10 requires Help systems to be created in RoboHelp 10 to work properly, at least when allowing blocked content?

It seems to be time for the old divide and conquer approach.
Zip up the project so you have a copy that cannot accidentally be opened and worked on. That gives you a copy that you can safely revert to later if needed. Save the zip file somewhere safe.
Then create another copy of the project so that you have two copies that can be worked on.
Open Copy 1 and delete half the topics. Ignore any broken links reported. Generate the help from that copy.
Open Copy 2 and delete the other half of the topics. Generate the help from that copy.
It should be the case that one copy is now OK and one still has the problem.
Trash the good copy and then create a second copy of the copy with the problem.
Repeat the process until you have located whatever is causing the problem.
The process takes less time than you might think.
See www.grainge.org for RoboHelp and Authoring tips
@petergrainge

Help topics are not displaying when using Windows 7 / IE 9 / RH10

We recently upgraded our library from RH8 to RH10. Also used a trial version of RH9 in this process. Now when we compile several of the projects have issues where help topics do not display when selected in the TOC or when a link to the topic is clicked within another internal topic. It is in a continous loop in the browser (like it is trying to load). If you right-click on the topic it displays (we are currently using this as the work-around). Anyone else having this problem?? I saw something similiar for Windows8/IE10, but the fix does not apply here (http://forums.adobe.com/message/5138909#5138909#5138909).

Hi,
I (April) apologize I have been OOO and have not been able to respond to your replies.
Let’s start over.
We have an issue where help topics do not display when selected in the TOC or when a link to the topic is clicked within another internal topic. It is in a continous loop in the browser (flickering like it is trying to load). If you right-click on the topic it displays (we are currently using this as the work-around).
We use Windows 7, IE9 and RH10 for all our projects. (Recently upgraded from RH8 to RH10)
Turns out the problem is not isolated. I have run across it in at least one other project, which leads me to think it also occurs in others.
"Does this only occur when the help is called from your software? Is it OK if you double click the start page?"
          No. I it ALSO occurs when launched from the start page.
Have you tried deleting the CPD file and reopening Rh and the project?
          Yes, without success.
Are you using any redirects?
          Per (Adrienne), “I am not using any redirects. I encounter this issue only in IE. If I paste the .htm into a Firefox browser, the help displays as it should.”
          I will add that the project also displays incorrectly in Google Chrome.
Thanks April

The volume up and down controls on my wireless keyboard show a no entry sign and do not respond when used...please help?

The volume up and down controls on my wireless keyboard show a no entry sign and do not respond when used...please help?

If you want to get a little more "exotic" you can try remapping the function keys. I did a little google searching and the hits that looked promising are,
Mapping volume and eject keys to 3rd-party keyboard Other Hardware
Spark
Spark is a powerful, and easy Shortcuts manager. With Spark you can create Hot Keys to launch applications and documents, execute AppleScript, control iTunes, and more...
You can also export and import your Hot Keys library, or save it in HTML format to print it.
Spark is free, so use it without moderation!

How can i set songs within a playlist, or an entire playlist, so that they are not included when using the shuffle function on IPOD Classic? Is this possible?

How can i set songs within a playlist, or an entire playlist, so that they are not included when using the shuffle function on IPOD Classic?
Is this possible?

You can set any song to Skip when shuffling.
In your iTunes Library, highlight the song and right-click/Get Info. On the Options tab is the Skip when shuffling box. Select that and then Sync the iPod with your Library.

All applications are not responding when wake from sleep.

All applications are not responding when Macbook pro wake from sleep,
the keyboard and touch pad are okay.
Why?
Thanks a lot.

I want to see if there's a service that may be preventing it from working properly when waking from sleep. To test this, we'll need to Disable all non-system-critical services to see if the issue occurs.
If it does not, that means one of those services that was disabled, is causing the issue.
If the touchscreen is still unresponsive after sleep with all of those non-critical services disabled, then it may be something with the registry or the hardware.
Here are the steps to disable non-critical services:
Windows + Q to bring up Search
Type 'msconfig' and press Enter
Click the Services Tab
Check the Hide All Microsoft Services box
Click the Disable All button
Click Apply and Restart
Once it restarts let it go into sleep mode and then wake it back up from sleep mode and test the touchscreen. Do this a couple of times, if you have time. (When you're done troubleshooting, you'll have to go back into msconfig and re-enable all of those non-critical services, apply and restart.)
Let me know the results when you get a chance, please

Cs12 trial not responding when installed, windows 7 64bit...how to fix??

cs12 trial not responding when installed, windows 7 64bit...how to fix??
Not a very good recommendation for buying the app!!!!
Does anyone at Adobe follow these questions??? If so please respond (your app will not!!)

Hi wcarlstrom,
Adobe CS12 is unheard of. Adobe Creative Suite's latest version is CS6.
Please be specific as to what software you are trying to install, OS version etc so that I may be able to help you.

My Elements 9 is not responding when started Windows

My Elements 9 is not responding when started Windows.

Without proper system information and otehr details such as the crash log from the Event Viewer nobody can say much.
Mylenium

Windows 10 - Skype not respond when I change language with Grave accent

Windows 10 - Skype not respond when I change language with Grave accent

Switching languages quickly in Windows 10 with the current version of Skype is a known issue. Hopefully a future update will address the problem.

Internet Explorer 9 not showing as not installed when using Windows Update - Error: Code 9C48 Windows Update encountered an unknown error.

I built a few new Windows Server 2008 R2 with SP1 VMs today and ran into a problem where Windows Update is not detecting the fact that Internet Explorer 9 is already installed. Internet Explorer 9 keeps showing up as an available update when
using Windows Update. When I try to install it as a test I get the error message: Code 9C48 Windows Update encountered an unknown error.
My normal build procedures include applying all the patches for the OS prior to any other work on the servers. The way I like to do the patching is to do every update other then IE9 in the begininng and once all the other updates have been
completed, install IE9 and then patch it if there are updates available. I followed this procedure on every build for the last year and I have not run into any issues until today. The only difference today is the latest patches that were released yesterday
April 10th, 2012. To test the theory that it may be one of the latest patches, I reinstalled Windows from scratch making sure to format the disks and then I installed IE9 right after the OS install without any other updates. Once the
server was rebooted, I checked Windows Update and Internet Explorer 9 still showed up as update (Not the Cumulative Update which normally shows up after an IE9 install) and yes, I did make sure to click the 'Check for Updates' link before I looked just
in case. My next test was to patch a couple of the servers I had built prior to April 10th, 2012. Those servers did not have any issues with the latest updates and they are not experiencing the same behavior as the newly built servers.
I ended up comparing the IE9 Version on the cleanly install OS (No updates were installed except IE9) and the servers I built last week which were patched. The versions are exactly the same.
My findings above lead me to believe that there is a problem with the latest IE9 install package (which includes the latest cumulative update) and the Windows Update detection component.
I guess I am looking for someone to report this up the chain to get this fixed so no one else runs into this problem. I know in some cases we may not be able to see additional IE9 updates until this is resolved.

I just started having the same problem.
I was creating a new VM in Vsphere from our 2008 R2 SP1 image and it hasn't been updated and repacked in a while, so i have to install about 60 updates, including IE9.
I went through my normal setup as i had just created 2 VMs and updated them on Monday with no problem.
I got the same error code as you. The install looks like it installed IE9, but the update is still showing up as available in Windows Update.
I deleted the VM, created a new one, chose all updates except IE, then did that and it still shows up again.
Then i deleted the VM, installed just IE 9 and it still shows up as available on reboot.
I have a script that i can use to reset/clear WSUS cache on the computer, (Software distribution folder, and the windows update log, and recreates a certificate), so i tried that and then rebooted and it still showed up.
I then decide ok, maybe the Image got messed up somehow, so i started creating a new 2008 R2 install from scratch last night and chose to update just IE9 as the first install. I did that, rebooted and it didn't show up in Windows Updates, so i though GREAT.
I proceed to kick off the 100+ downloads needed before i left and left the console up.
When i got in to work this morning, the updater seemed stuck on 31 of 102 updates, this one in particular: KB288516. I rebooted the computer, because it wouldn't stop and just seemed stuck since last night, which these updates should only have taken about
an hour to install at most. I log back in and sure enough, it now shows Internet Explorer 9 at the bottom of the update list as being needed for install.
I believe this is Patch Tuesday week, so maybe they screwed up something with the Windows Update detection engine, because it worked fine on Monday when i had to update IE9 on 2 VMs that i created.

Update link on officejet j4540 shows on desktop will not respond. Using windows 7

Had an older computer using Windows XP with the Officejet j4540 with no problems. Computer died. Bought new computer running Windows 7 Home. Installed printer & downloaded new software. Got the blue tag on desktop to update but tag would not work. Ordered and install the software disk from HP. Uninstalled downloaded software & installed printer from the disk. Still same results. Have not been able to get updates.
Byron

Byron, would first uninstall the printer entirely from the computer. First disconnect the USB cord (if one is used). Then make sure that any related files or programs are entirely removed or deleted from Programs and Features, Devices and Printers, and the Device Manager. Then restart the computer.
Do not plug the USB cord in until the software asks for it.
Then go to http://goo.gl/wUs2E and locate your appropriate drivers and software for your particular printer model. They are all available for free downloads. You will want to use the "Full Feature" version of the software package.
Let me know how this goes!

Keep getting "not responding" when using Yahoo's new version of email on a Win8 Lenovo computer

Firefox no longer works properly. I tried the reset Firefox option, but that did not help. When I try to delete an email, I receive the not responding message. When I try to move an email into a folder I receive the message. When I try just to go to the next email, I receive the message. If I try to mark a message not spam, nothing happens. If I wait, eventually Firefox responds and I can move on to the next email. Obviously this is very time consuming and I find that I just don't read my email as I don't what to spend the time. I contact Yahoo and they responded back that it is a browser issue. Because Firefox is the only browser I have on my computer I need to get this working properly again. One more thing, sometime this non-responsive message shows up when I am using other sites, but just not as often as when I'm trying to read my Yahoo emails.
I thank you in advance for answering my question and try to help me get this issue resolved.

To rule out Flash as a potential culprit, could you try one or both of the following:
(1) Disable the Protected Mode feature of the Flash Player plugin.
The following pages provide different ways to do that:
* Adobe support article under the heading "Last Resort": [http://forums.adobe.com/message/4468493#TemporaryWorkaround Adobe Forums: How do I troubleshoot Flash Player's protected mode for Firefox?]
* Manual steps: https://support.mozilla.org/questions/968190?page=5#answer-509209
* Batch file to automate the manual steps: https://support.mozilla.org/questions/982093#answer-518078
Flash needs to completely unload from memory (restarting Firefox might help) before this would take effect.
(2) Set Flash to Click-to-Play ("Ask to Activate").
This will delay Flash from starting on a page until you approve it, which will help distinguish Flash-generated issues from page load and layout issues.
To set "Ask to Activate", open the Add-ons page using either:
* Ctrl+Shift+a
* orange Firefox button (or Tools menu) > Add-ons
In the left column, click Plugins. Look for "Shockwave Flash" and change "Always Activate" to "Ask to Activate".
When you visit a site that wants to use the Flash, you should see a notification icon in the address bar and one of the following: a link in a black rectangle in the page or an infobar sliding down between the toolbar area and the page.
''Any improvement in these scenarios?''

Heavy lag and "not responding" when using Preview for PDFs

Hi there,
I have a problem with my MacBook Pro (9,1 15" Late 2012) running Mavericks 10.9.1.
Sometimes (quite often in the last weeks) Mavericks getting furious when I try to preview PDFs. This happens:
- I get an PDF. It came from my eXactScan add, from an email adress or I downloaded it - the source doesn't matter.
- I open the finder and want to preview the PDF with the built in preview and I get the spinning circle / load indicator. The circle runns for a long time.
- I can use Mavericks without any problems but the Finder only shows a small thumbnail of the file I wanted to preview.
- Now it's getting dirty: when I double click the PDF to view it with the Preview app the whole system "crashes":
the Preview app won't open (but it is shown in the dock),
my open Mail and Chrome wont react any more or start to lagg very heavy,
the Finder laggs very heavy
but the OS (menubar, dock, etc) responds without any problems.
If I open the "Close Apps" window the apps mentioned above are marked with "not responding".
I waited for some time but nothing gets better.
The only way to get rid of the problem is to restart the Mac which works without any problems.
That's it.

Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your personal files or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you boot, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, reboot as usual (not in safe mode) and verify that you still have the problem. Post the results of steps 1 and 2.

Elements 11 not responding when using "comic" or "graphic novel" filter

I recently purchased PSE 11 and absolutely LOVE the program. It has worked flawlessly for me for 3 weeks, however, today was the first time I ever tried to use the "comic strip" filter and the "graphic novel" filter and the program stopped responding when trying to use these filters.
I am able to use the other filters contained under the "sketch" dropdown menu, however, the 2 that I have mentioned do not seem to work.
Any ideas what might be wrong?
I am running a Windows 7 computer and as previously mentioned, all other functionality seems to be working in Elements 11 except for those 2 filters.
Thanks for any help you can provide!

Try resetting the PSE preferences by
   1. Close Elements.
   2. Launch the Photoshop Elements Welcome Screen and hold down ctrl + alt + shift as you click Edit.
   3. Continue to hold the keys until you see a message box asking if you want to delete Photoshop Elements settings file; click Yes. Elements will open with default preferences.
OR
GO to Edit->Preferences and you will see Reset Preferences on next launch
Click this button to ensure that all product preferences are reset to default settings when Elements Editor is restarted next. Available at Preferences > General.
OR
Try with normal JPEG image also.
Thanks,
Garry

Spinning circle * Thunderbird is not responding when I try to write or access emails. I had attempted to delete a bunch of old txt messages in seldom used Gmail

I saw I had almost 30,000 txt messages on a Gmail account that I had created a gmail account for on Thunderbird. I didn't realize that they were going here from Gmail. I highlighted all of them and attempted to delete them. The spinning circle finally went away and all of them were gone. But when I tried to do anything else on Thunderbird with my regular email accounts (Comcast & Hotmail), I would get a spinning circle and Thunderbird is not responding. I had to use Ctrl Alt Del and then reopen. I tried compacting but this morning when I tried to write an email from one of my Comcast emails in Thunderbird, again I got the spinning circle and Thunderbird is not responding. In order to do anything, I have to close the program by hitting Crrl Alt Del and try again.
My Trash Local folders says 8300.
This morning, when I tried accessing Thunderbird at the bottom of the taskbar it said, "downloading....of 17,000 to All Mail. Had no clue what that meant. I let it continue until all were and thought my issue would be resolved. But no. :(
Something obviously got corrupted in the program. What do I need to do to fix this?
Thank you.
Fred

''FredricJLowe [[#question-1041566|said]]''
<blockquote>
I saw I had almost 30,000 txt messages on a Gmail account that I had created a gmail account for on Thunderbird. I didn't realize that they were going here from Gmail. I highlighted all of them and attempted to delete them. The spinning circle finally went away and all of them were gone. But when I tried to do anything else on Thunderbird with my regular email accounts (Comcast & Hotmail), I would get a spinning circle and Thunderbird is not responding. I had to use Ctrl Alt Del and then reopen. I tried compacting but this morning when I tried to write an email from one of my Comcast emails in Thunderbird, again I got the spinning circle and Thunderbird is not responding. In order to do anything, I have to close the program by hitting Crrl Alt Del and try again.
My Trash Local folders says 8300.
This morning, when I tried accessing Thunderbird at the bottom of the taskbar it said, "downloading....of 17,000 to All Mail. Had no clue what that meant. I let it continue until all were and thought my issue would be resolved. But no. :(
Something obviously got corrupted in the program. What do I need to do to fix this?
Thank you.
Fred
</blockquote>
When I try to go the Gmail address. it has the spinning circle and says, "opening folder and at the top Thunderbird is Not Responding"

Enterprise DNS servers are not responding when using Windows NLB with Direct Access 2012

Similar Messages

Maybe you are looking for