EoMPLS support on Cisco ISR G2 2921?

Hi there is saw in feature navigator that EoMPLS is a supported feature for 2921...
- Can somebody please confirm that EoMPLS is supported with Cisco 2921?
- Is pseudowire redundancy possible?
Thanks
Manuel

Hi Manuel,
yes it is supported (if I am not wrong since release 12(4)T) and also L2VPN PW redundancy is supported.
Riccardo

Similar Messages

MPLS CE support on Cisco 2800 ISR router

Hi all, could I ask you for some hints about MPLS CE support on Cisco 2800 ISR router today? I`m finding restrictions and recommendations for feature implementation. Do you have any cisco web site about them?
Thank you for your advice and/or hints.
Peter

Thanks for an answer. I need to use multi-VPN model on CE router, but with QoS on one physical CE-PE connection (e.g. Frame-Relay DLCI).However, all VPNs on CE router must be secured for each one. The solution is Multi-VRF service feature, but, however, with multi-DLCI model on Frame-Relay and QoS per DLCI. Now, I`m finding a scenario to provide multi-VPN model on CE router with single-DLCI model and single QoS per one DLCI for all VPNs. And that, MPLS CE feature on C2800 could be used, if possible.
So, I don`t know more about MPLS CE on C2800 and I don`t know make a result to propsed solution...

Cisco 3925 with ethsw module EoMPLS support

Hi,
I am looking for clarification that the ethsw module, NM-16ESW, will not allow for EoMPLS support?
From what I have read on CCO it seems to suggest that the EHWIC-4/8ESG is needed to support this?
Basically, I had 15.2(4)M1 on my 3925, but none of the EoMPLS VC's would come up for the vlans that were attached to the ethsw module. Other EoMPLS VC that used onboard gig ports came up just fine. All LDP signalling/routing is correct.
Can anyone provide any confirmation?
Thanks,
LR

Hi,
The switch (NM-16ESW) inside your router runs an image for the 3560 switches and the 3560 switches don't support MPLS. They only support vrf Lite.
HTH

Cisco ISR G2 SIP Calls Capacity

Dear all,
We're planning for Cisco Voice Gateway configuration with SIP trunk, till now no E1s are used.
I would like to know how can we calculate the number of simulataneous calls that a cisco ISR G2 router (1921. 2921.3945,etc...) can support ?
How much sip simultaneous calls each ISR G2 model can support ?
Is it better to use SIP or we must get into E1 PRI ?
Regards,

The Q and A below has the call capacity you are looking for
Table 1. Number of IP-to-IP Calls per Platform
Platform
Maximum Number of Simultaneous Calls (Flow-Through)
Cisco 3945E
2500
Cisco 3925E
2100
Cisco 3945
950
Cisco 3925
800
Cisco 2951
500
Cisco 2921
400
Cisco 2911
200
Cisco 2901
100
Cisco ASR 1004; and Cisco ASR 1006 Router Processor 2 (RP2)
5000; 16000*
Cisco ASR 1002, ASR 1004, and ASR 1006 RP1
1750
Cisco AS5350XM and AS5400XM
600
Cisco 3845
500
Cisco 3825
400
Cisco 2851
225
Cisco 2821
200
Cisco 2811
110
Cisco 2801
55
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6790/gatecont/ps5640/prod_qas09186a00801da69b.html
Please rate all useful posts
"opportunity is a haughty goddess who waste no time with those who are unprepared"

Maximum cos1 (voice traffic) supported by Cisco ASR 1006 router

Dear Team,
Please confirm the maximum cos 1 traffic supported by cisco ASR 1006 router.

Yes, it would. If you are planning on terminating a single site on this router I would spread over multiple routers for redundancy.
Table 6 explains number of ports and channels providing you have the DSPs:
http://www.cisco.com/c/dam/en/us/products/collateral/routers/2800-series-integrated-services-routers-isr/product_data_sheet0900aecd8057f2e0.pdf

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

• PI provides visibility for autonomous clients within the same list view as lightweight and wired clients (client list page).
• Rogue AP detection for autonomous AP's is not supported (it's supported in CUWN).
• Alarms/events for client authentication issues (e.g. authentication failure) are displayed in PI.
• Config management for autonomous AP's is via CLI template. Config comparison and archiving functionality in PI leverages these same features that were brought in from LMS, so need to defer to others in terms of whether this is a cross-platform feature in PI or is only supported on a subset of platforms. Config comparison/archive is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client sessions, etc.) reports, and there are extensive reports for CUWN

Dynamic Routing Protocol Support in Cisco ASA Multiple Context Mode

                   Dear Experts,
Wold like to know whether dynamic Routing Protocol Support in Cisco ASA Firewall Multiple Context Mode. If yes then please provide OS version and Hardware Model of Cisco ASA Firewall. Appreciate the quick response. Thanks.

Hi,
Check out this document for the information
http://www.cisco.com/en/US/docs/security/asa/roadmap/asa_new_features.html#wp93116
Its lists the following for software level 9.0(1)
Multiple   Context Mode Features
Dynamic routing in Security   Contexts
EIGRP and OSPFv2 dynamic   routing protocols are now supported in multiple context mode. OSPFv3, RIP, and multicast routing   are not supported.
Seems to me you would need some 9.x version to support the above mentioned Dynamic Routing Protocols.
I don't think its related to the hardware model of the ASA other than that it requires a model that supports Multiple Context Mode. To my understanding the only model that doesnt support that is ASA5505 of the whole ASA5500 and ASA5500-X series.
Hope this helps
- Jouni

Is VSS supported in Cisco Prime Infrastructure 1.2?

Is VSS supported in Cisco Prime Infrastructure 1.2?

VSS support (converting standalone switches into a VSS) was introduced with LMS 3.0.1 if I remember well and it is still there in LMS 4.2 (Cisco Prime Infrastructure):
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/user/guide/configuration/configvss.html
Config Mgmt is supported, also.

If we got Nexus 1000V from VMWARE , can we add the N1K to our CCO ( Cisco Account ) to have direct support from Cisco

Hi
If we got Nexus 1000V from VMWARE , can we add the N1K to our CCO ( Cisco Account ) to have direct support from Cisco
as sometimes it take some more time to get answer from VMWARE -> Cisco
Thanks

No. When you purchase support from Vmware, they are your support contact and they will escalate support to Cisco on your behalf if needed. This is the case for all OEM support. Cisco provides support for RHEL, Microsoft and VMware. We follow the same practice.
Deciding who to purchase support from is a decision of single point of contact for all VMware & N1K related issues vs. maintaining separate support contracts with each vendor individually.
Regards,
Robert

How many numbers of GRE Tunnels are supported on Cisco 3925 router?

Hi...
I would like to know that.......
How many numbers of GRE Tunnels are supported on Cisco 3925 router?
Thanks....

This is what I found in my search:
There may be factors such as memory constraints that will place practical limits on how many tunnels you can support. But there is also a hard limit on the number of tunnels that you can configure. That limit is based on the limitation of the number of IDBs supported by your router. The IDB is the Interface Descriptor Block and each interface (physical, or tunnel, or loopback, or whatever) requires an IDB. The number of IDBs will vary by platform and sometimes by release level of the code that you are running. You can use the privileged command show idb to see what the limitation is on your router. On the 1841 router that I just checked the limit on IDB is 1200 (which is a pretty large number - I believe that you would encounter other limits on performance or on size of configuration before you exhaust the IDB limit).
https://supportforums.cisco.com/thread/2007932
Hope it helps.
Jatin Katyal
- Do rate helpful posts -

QinQ support on Cisco SUP7L-E?

Current release note for Cisco IOS XE Release 3.2.0XO says:
These sections list the limitations and restrictions for the current release of Cisco IOS software on the Catalyst 4500E series switch.
•802.1q tunneling and related features are not supported.
but in feature navigator there is 802.1q available
- IEEE 802.1Q Tunneling
- Selective QinQ
Sup 6E has support also:
Be aware that 802.1Q requires WS-C4948, WS-C4948-10GE, ME-4924-10GE, WS-C4928-10GE, WS-C4900M, WS-X4013+10GE, WS-X4516, WS-X4516-10GE, or WS-X45-SUP6-E; Layer 2 protocol tunneling is supported on all supervisor engines.

Hi Riccardo,
I checked the tables and for my unterstanding SUP7L-E and SUP7-E are SW feature parity…
Out of the release note:
Additionally, Supevisor Engine 7L-E running Cisco IOS 3.2.0XO has feature parity with Supervisor Engine 7-E running Cisco IOS XE 3.2.0SG.
The feature set for Supervisor Engine 7L-E matches that of Supervisor Engines 7-E
That means Q-in-Q should also work on SUP7L-E within next IOS release (March – May 2012) … or am i wrong?
Thanks
Manuel
Von: rsimoni
Gesendet: Dienstag, 10. Januar 2012 16:52
An: Linder Manuel (CASSARiUS AG)
Betreff: - Re: QinQ support on Cisco SUP7L-E?
Home
Re: QinQ support on Cisco SUP7L-E?
created by Riccardo Simoni in Other Service Provider Subjects - View the full discussion

Can IPV6 QOS support in Cisco 3750x switches

Hi
I have tried IPv6 qos using class map in Catalyst 3750 switches but the platform is not support.
Can anyone configured the IPV6 qos in Cisco 3750-X switches. Does it support?
Cisco 3750 config
policy-map up
class bwtest-up
police 2048000 128000 exceed-action drop
policy-map down
class bwtest-down
police 512000 128000 exceed-action drop
trust dscp
class-map match-all bwtest-up
match access-group name bwup
class-map match-all bwtest-down
match access-group name bwdown
ipv6 access-list bwup
permit ipv6 2402:xxxx:x:x::/64
ipv6 access-list bwdown
permit ipv6 any 2402:xxxx:x:x::/64
L3(config)#int g1/0/4
L3(config-if)#service-policy input up
QoS: class(bwtest-up) IPv6 class not supported on interface GigabitEthernet1/0/4 ( error)
Please help!

interface GigabitEthernet1/0/4
description ##Test LAN-IPV##
no switchport
bandwidth 2048
no ip address
load-interval 30
speed 100
duplex full
ipv6 address 2402:xxxx:x:x::1/64
ipv6 enable
ipv6 ospf 200 area 0
end
switch sw version
Cisco IOS Software, C3750 Software (C3750-IPSERVICESK9-M), Version 12.2(55)SE9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Mon 03-Mar-14 22:45 by prod_rel_team
Image text-base: 0x01000000, data-base: 0x02F00000
ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)
Cherry uptime is 6 days, 7 hours, 23 minutes
System returned to ROM by power-on
System restarted at 07:04:50 IST Thu Mar 19 2015
System image file is "flash:/c3750-ipservicesk9-mz.122-55.SE9.bin"

Rate limit in Cisco ISR 4451X

Hello friends,
I have a problem; now i'm changing the router that have at work of Cisco 3925 to Cisco ISR 4451X but in the new router i can't put the command that have in my old router:
rate-limit input access-group 110 16384000 3072000 6144000 conform-action transmit exceed-action drop
Can someone help me telling what command replace it or which is the equivalent?
Atte.
Percy

Edison,
Thanks for helping with this it is greatly appreciated. I have been playing around with this and have managed to get the policing working successfully on the SVI.
The problem was basically the direction the policing was being applied. Initially I was applying the service policies to the customer SVIs in an inbound direction. This would only be traffic coming into the VLAN interface from within the VLAN; therefore, in terms of internet traffic this would be upload and NOT the required download.
In order to resolve this, I have applied the service policy to the Internet facing VLAN. Please see below -
Class Maps and Policy Maps
class-map match-all CUST-A-VL10-CMAP1
match input-interface FastEthernet1/0/24
class-map match-all CUST-A-VL10-CMAP2
match access-group name CUST-A-VL10-ACL-POL
policy-map CUST-A-VL10-PMAP1
class CUST-A-VL10-CMAP1
police 100000 18750 exceed-action drop
policy-map CUST-A-VL10-PARENT-PMAP1
class CUST-A-VL10-CMAP2
set ip precedence 1
service-policy CUST-A-VL10-PMAP1
VLAN Confguration
interface Vlan300
ip address ************
service-policy input CUST-A-VL10-PARENT-PMAP1
This works successfully and polices the traffic as expected. However, I have now run into the problem with assigning multiple service policies to the VLAN interface. As this is the internet facing VLAN for the routing of traffic to and from the internet, all customer service policies need to be applied to this interface. When I attempt to apply more than one service policy to this VLAN i receive the following error -
(config-if)#service-policy input CUST-B-VL20-PARENT-PMAP1
Policy map CUST-A-VL10-PARENT-PMAP1 is already attached
Looks like another couple of hours needed working around this problem!!
Thanks
Nick

Are HTTPS probes supported in Cisco devices ?

Hello,
I am aware Cisco supports HTTP probe types. Are HTTPS (HTTP Secure) probes are supported in Cisco devices too ? If so from which IOS version ?
Your comments are very much appreciated.
Thanks.

Hi ,
As per my understanding there is No IOS code which support HTTPS opeartions , Only HTTP operations are supported as of now.
Thakns
Afroz

Cisco isr 819 cellular interface...

my cisco isr 819 constantly cycles between the gigabyte interface and the cellular...? _i have the device configured for auto failover with the gigabyte interface being the primary and the cellular as backup. _i used Cisco Configuration Pro to configure the router. _i have attached the router config for expert evaluation.....thanks in advance.

Yes you are correct Cinthia, it is the NAT and depending on which external interface i configure first with NAT, that's the only interface providing NAT to out going packets.
What i hope to achieve with my C819HG ISR router is provide the G0 interface as primary internet access. If that access goes down i want the Cellular0 interface to come up and provide a path to the internet. When the G0 access is restored i want the Cellular0 interface to go back to standby.
here is my config.....
! Last configuration change at 14:30:15 Chicago Thu Feb 19 2015 by ADMIN
version 15.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname rtr-cisco
boot-start-marker
boot-end-marker
aqm-register-fnf
no aaa new-model
clock timezone Chicago -6 0
clock summer-time Chicago date Apr 6 2003 2:00 Oct 26 2003 2:00
crypto pki trustpoint TP-self-signed-3083563774
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3083563774
revocation-check none
rsakeypair TP-self-signed-3083563774
crypto pki certificate chain TP-self-signed-3083563774
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33303833 35363337 3734301E 170D3135 30323133 32313035
35305A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 30383335
36333737 3430819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100AB4C 2DA1C3C3 CABBB054 765A1E14 A7BA0347 AFFD1913 B04113DD A21D7CEB
F09F6572 5BF58323 586BEF24 929003D4 4CAD8864 A00FF40A A59A9969 C12615A0
1DFE5527 BA6E2C27 33F75615 A36DA242 42862F33 D2823AA3 B838AA3B C938930A
6D48BD79 11BD9CF5 8B7BEBC8 8C6D9D34 6E5415EB A3CFF3C7 E48F20C4 B18B15FE
38BD0203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 14B5AEAA D7E9FEF2 3A4FF79D 4251425F EF9F28DC 61301D06
03551D0E 04160414 B5AEAAD7 E9FEF23A 4FF79D42 51425FEF 9F28DC61 300D0609
2A864886 F70D0101 05050003 81810039 C6D2590C 0741F53E 62E6E7CE 62534CF9
3A8A6C79 BECBACD7 AF73FA4C 8ED5C059 58A7B08C FBCE2ED0 66196250 20C570AC
8D802A6B 5E33FFD7 580BBC4C 7C442C42 0F77E3FD F465B724 69D29CFF 19F59635
D55A9E71 290CE668 B2C74CA1 ED641A2E 714BC06F 17CE9E44 B998945A C1733318
BFDA96CD 9D66ACA7 B1D79229 8A1322
quit
ip dhcp excluded-address 172.17.37.1 172.17.37.9
ip dhcp excluded-address 172.17.37.16 172.17.37.254
ip dhcp pool ciscoPool
import all
network 172.17.37.0 255.255.255.0
dns-server 8.8.8.8 8.8.4.4
default-router 172.17.37.1
ip domain name sr.nwris.noaa.gov
ip cef
no ipv6 cef
multilink bundle-name authenticated
chat-script lte "" "AT!CALL1" TIMEOUT 20 "OK"
license udi pid C819HG-4G-V-K9 sn FTX181583HV
username ADMIN privilege 15 secret 4 wYSo2PORqoebHxp3dazS6tzNpgOc5RQBMmrsFZ5l6jE
controller Cellular 0
track 1 ip sla 1 reachability
ip ssh version 2
ip scp server enable
interface Cellular0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer string lte
dialer-group 1
async mode interactive
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface GigabitEthernet0
description $ETH-WAN$
ip address dhcp client-id GigabitEthernet0 hostname rtr-wxk37
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface Serial0
no ip address
shutdown
clock rate 2000000
interface Vlan1
ip address 172.17.37.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip local policy route-map track-primary-if
ip forward-protocol nd
no ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 1 interface Cellular0 overload
ip nat inside source list 2 interface GigabitEthernet0 overload
ip route 0.0.0.0 0.0.0.0 GigabitEthernet0 track 1
ip route 0.0.0.0 0.0.0.0 Cellular0 253
ip sla auto discovery
ip sla 1
icmp-echo 8.8.8.8 source-interface GigabitEthernet0
ip sla schedule 1 life forever start-time now
dialer-list 1 protocol ip permit
route-map track-primary-if permit 1
match ip address 100
set interface GigabitEthernet0
route-map source permit 10
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 172.17.37.0 0.0.0.255
access-list 2 remark CCP_ACL Category=2
access-list 2 permit 172.17.37.0 0.0.0.255
access-list 100 remark CCP_ACL Category=0
access-list 100 permit icmp any host 8.8.8.8
control-plane
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
mgcp profile default
line con 0
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
stopbits 1
line 3
script dialer lte
modem InOut
no exec
transport input all
rxspeed 100000000
txspeed 50000000
line vty 0 4
login local
transport input ssh
scheduler allocate 20000 1000
ntp update-calendar
ntp server 24.56.178.140 source GigabitEthernet0
ntp server 129.6.15.28 prefer source GigabitEthernet0
ntp server 132.163.4.102 source Cellular0
end

EoMPLS support on Cisco ISR G2 2921?

Similar Messages

Maybe you are looking for