EoMPLS Xconnect between 2811XM and 7606 with RSP720

We have an urgent need to quickly deploy an MPLS capable router to carry l2 traffic. We use mpls xconnects throughout our network. I am having difficulty establishing an xconnect between a 2811XM ISR and a 7606. OSPF and BGP are up, MPLS establishes, but cannot get the tunnel to come up. Any ideas? Is 2811 even capable of MPLS xconnects?
Thanks in advance,
Scott.

Thanks for the quick response, I have included the show ver, and the command you asked for. Please let me know if there is anything esle that might help. Thanks.
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(24)T, REL
EASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 25-Feb-09 17:55 by prod_rel_team
ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)
ERIN-ppt2801s1 uptime is 9 hours, 6 minutes
System returned to ROM by power-on
System image file is "flash:c2800nm-advipservicesk9-mz.124-24.T.bin"
2811 mpls vc detail:
Local interface: Fa0/1.1601 up, line protocol up, Eth VLAN 1601 up
Destination address: 1.0.16.1, VC ID: 1601, VC status: down
Output interface: none, imposed label stack {}
Preferred path: not configured
Default path: no route
No adjacency
Create time: 06:52:06, last status change time: 06:52:02
Signaling protocol: LDP, peer 1.0.16.1:0 up
MPLS VC labels: local 83, remote 188
Group ID: local 0, remote 0
MTU: local 1500, remote 1500
Remote interface description: g1/47.1602 ERIN COT2
Sequencing: receive disabled, send disabled
VC statistics:
packet totals: receive 0, send 0
byte totals: receive 0, send 0
packet drops: receive 0, seq error 0, send 0
7606 mpls vc detail:
Local interface: Gi1/47.1601 up, line protocol up, Eth VLAN 1601 up
Destination address: 1.0.16.70, VC ID: 1601, VC status: down
Output interface: none, imposed label stack {}
Preferred path: not configured
Default path: no route
No adjacency
Create time: 07:32:23, last status change time: 06:52:55
Signaling protocol: LDP, peer 1.0.16.70:0 up
Targeted Hello: 1.0.16.1(LDP Id) -> 1.0.16.70
Status TLV support (local/remote) : enabled/not supported
Label/status state machine : activating, LruRruD
Last local dataplane status rcvd: DOWN(PW-tx-fault)
Last local SSS circuit status rcvd: no fault
Last local SSS circuit status sent: DOWN(PW-rx-fault)
Last local LDP TLV status sent: DOWN(PW-tx-fault)
Last remote LDP TLV status rcvd: not sent
MPLS VC labels: local 188, remote 83
Group ID: local 0, remote 0
MTU: local 1500, remote 1500
Remote interface description:
Sequencing: receive disabled, send disabled
VC statistics:
packet totals: receive 0, send 0
byte totals: receive 0, send 0
packet drops: receive 0, seq error 0, send 0

Similar Messages

Is it possible to transfer music between iPhones and iPods with out using iTunes

Is it possible to transfer music between iPhones and iPods with out using iTunes

Nope. Both require iTunes on a computer to sync music from.
Unless the iPod is an iPod Touch and the music was bought from iTunes. In which case the Touch can simply go to the iTunes App, under Purchased and download the purchased songs for free.

Difference between validation and susbstittution with tcodes

hi all can any body tell me about difference between validation and susbstittution with tcodes
regars
sravya

Hi,
Settting up the FI Validations
You can use additional validation to supplement the existing SAP logic to fit you into your businness needs.
For e.g. to allow postings from company code 0001 to business area AA only.
GGB0 - To maintain the validations
Validation - Enter a validation name e.g. VBUS
Applicaion Area - SAP module e.g. FI
Calling Point - Dependent upon the application area that is selected.
0001 - Document Header - validate enteries at document header, e.g BKPF table
0002 - Line Items - check line item entris within a document, e.g. BSEG table
0003 - Complete Document - check settings for the whole documents.
e.g. Validation step 001
Allowed company code '0001' to post to business area AA only. 'FI00' checks that line item is from FI.
If checks failed, the error message number 14 is displayed to stop the transaction.
Prerequisite
<BSEG> $BUKRS = '0001' AND
<BKPF> $GLVOR = 'FI00'
Check
<BSEG> $GSBER = 'AA'
Message
Type E No. 14 - Business Area not allowed for company 0001
Output fields 1 - BSEG - GSBER 2 - BSEG - BUKRS
3 - 4
OB28 - Define Validations for Posting
CC CallPnt Validation Description Activtn Level
0001 2 VBUS Business Area Validation 1
Activtn Level - 0 - Not Active 1 - Activated 2 - Activated for all except batch input
GGB4 - Manage the activation of all validations in the SAP system.
Validations, Substitutions, and Rules
Purpose
With the validations and substitutions software, you can validate and/or substitute data at the time of entry in the FI-SL System and other SAP Systems.
Implementation Considerations
You do not need to change the standard system to customize your validations and substitutions. For each installation, you can define exactly which validations and substitutions are necessary to ensure the integrity of your data.
Features
Validation
In the SAP System, almost all input values are validated by a program or against tables or master files. Since some types of validations cannot be standardized, you can use FI-SL's validations program to create validations for your system.
With validations, you can check values and combinations of values as they are being entered in the SAP environment. Validation rules are stored in the Rule Manager; as data is entered, the Integration Manager validates the data against the validation rules stored in the Rule Manager. Because data is validated before it is posted, only valid information enters the FI-SL System.
You define validation rules using Boolean logic. When you define a validation rule, the system checks the validation rule to ensure that it is syntactically correct.
You can also define the result of breaking the validation rule. For instance, you can specify that a message is issued but the user can continue processing. You can also force the user to correct the error before processing can continue.
For more information, see Validation or What Are Validations?. For more information on using validations, see Creating a Validation. For more information on Boolean Logic, see Introduction to Boolean Logic.
Substitution
Substitution rules are stored in the Rule Manager. When data is entered in the system, it is substituted by the Integration Manager. The Integration Manager calls the Rule Manager. Substitution occurs before the data is posted to the FI-SL databases.
You define substitution rules using Boolean logic. When you define a substitution rule, the system checks the substitution rule to ensure that it is syntactically correct.
For more information, see Substitution or What Are Substitutions?. For more information on using substitutions, see Creating a Substitution. For more information on Boolean Logic, see Introduction to Boolean Logic.
Rules
A rule is a Boolean expression that you can use as a condition, as a check, or in another rule. Rules enable you to refer to frequently used Boolean statements simply by specifying the rule name.
The FI-SL Integration Manager uses Boolean logic. When you use Boolean logic and syntax, you can:
Validate data
Substitute data
Select ledgers for posting
Transfer substitution data to a rollup ledger
Select report data
The Rule Manager stores the Boolean rules used to analyze data. The Integration Manager calls the Rule Manager and determines whether entered data should be used. If a Boolean statement is true, an action is taken; if a statement is false, no action is taken.
Boolean logic is used in the following FI-SL modules:
Validation
Substitution
Ledger selection
Report Writer
Rollups
To use Boolean Logic in one of the functions listed, you create statements that are used as formulas in the FI-SL System. For more information on using Boolean Logic, see Introduction to Boolean Logic or Boolean Logic Statements and Rules.

What is the difference between Aggregation and Composition with example

plz help me to find the difference between Aggregation and Composition with example

Dear [email protected]:
Get back to work.
August 4, 2007 stalin_gnana asked:
I would like to know the description about 'is a' ,'has a' ..relationship in java.plz reply me to the above doubt if known
August 8:
Can any one encounter the clarification on how and where Observer class and Observable interface can be applied..plz answer me
August 10:
May you find a solution on why not have the concept of pointer,opterator overloading,virtual function and destructor in java
(Also August 10):
I would desire to apprehend the brief description about usage of Singletone class and where it can be applied.plz help me
Today:
I am having the doubt of 'is there any relation among Delegation and composition'.if have,plz answer to regarding question.
And then this thread today too.
sniff sniff
I smell a lazy attempt at getting others to do one's homework for him.

Whats the diff between PPOC and PPOC with Work flow?

Hi,
Can any one please tell me out the difference between Creating Organisational Structure under OM and creating under "Tools" with Work Flow ?
on Creation what would be changing factors between them?
And Explain me about Work flow and how it will be useful and also where and all it reflects in SAP HR?
Regards,
Vinoth Kumar.R

Hi
I need the procedural difference between PPOCE And PPOCE with work Flow.
Suppose if i need to create with PPOCE with work flow, is the Procedure would be the same or additionally I need to Activate some thing, It Might be very much Basic but i didnt work on othat so far.
If there is any notes or Links to learn about it, please forward as it is helpful.
Regards,
Vinoth Kumar.R

What is the difference between OCIEnvCreate and OCIEnvNlsCreate with utf16

because i find a oci sample code cdemouni.c,in this sample,use OCIEnvCreate with mode set OCI_UTF16,but OCIEnvNlsCreate also can set charset and ncharset OCI_UTF16ID,what is the difference between OCIEnvCreate and OCIEnvNlsCreate with UTF16?

First, OCIEnvNlsCreate() is recommended way of switching to UTF-16 mode.
Second, OCIEnvNlsCreate() uses new semantics for bind and define buffer lengths. With new semantics all lengths are in bytes. With old semantics,
UTF-16 string lengths are in codepoints, while other character sets use bytes.
You can get new length semantics with OCIEnvCreate() as well, by
adding OCI_NEW_LENGTH_SEMANTICS to the 'mode' flags.
-- Sergiusz

Is it possible to use Facetime between Mac and iPad with the same Apple ID?

Hello,
I have a MacBook Pro and an iPad. May MacBook is used by my wife and me at home. I take the Pad with me when I travel. On the MacBook I have and Apple ID registered. It is the same I use with the iPad. Do I need a differnt ID for my wife if we want to use Facetime? Or do I need to create a seperate user-profile for my wife on the MacBook?
Thanks for your feedback in advance.

Hi
I use the same apple id for the same thing when i travel between myself and people at home over my iphone and the ipad i leave at home always seems to work of for me
I normally just give it a little test before i leave each time by signing in of both devices and trying ringing myself
Hope this helps

SSL between NSAPI and WLS with custom certificate and RequireSSLHostMatch=true fails

I am trying to use SSL for communication between NSAPI and WebLogic
server (server authentication at the NSAPI).
Therefore, a custom server certificate is installed on WLS, containing this
server's hostname. The NSAPI is configured (RequireSSLHostMatch=true) to
check the hostname contained in the certificate against the WebLogicHost
parameter in the "obj.conf" file. The corresponding TrustedCAFile is installed
for NSAPI.
The SSL setup seems to work ok, but when matching the hostname, it seems like
NSAPI is trying to do a string-match against the numeric IP of the WebLogicHost,
not on the hostname as configured in the WebLogicHost parameter.
The relevant entry in the "obj.conf" file:
<Object name="weblogic" ppath="*">
Service fn=wl-proxy WebLogicHost=btsun2a.muc \
WebLogicPort=7162 \
Debug=ALL \
SecureProxy=ON \
TrustedCAFile=/home/qx13604/wls61/config/testdomain/TC_RootServer_PEM_Class0.pem
RequireSSLHostMatch=true
</Object>
I am using WLS6.1 with NSAPI (both Solaris). The content of "wlproxy.log" is as
follows.
Any ideas?
Content of "wlproxy.log":
Thu Oct 11 12:30:22 2001 INFO: SSL is configured
Thu Oct 11 12:30:22 2001 INFO: Initializing SSL library
Thu Oct 11 12:30:22 2001 Loaded 1 trusted CA's
Thu Oct 11 12:30:22 2001 INFO: Successfully initialized SSL
Thu Oct 11 12:30:22 2001 INFO: SSL configured successfully
Thu Oct 11 12:30:22 2001 ....relFile.../index.jsp...
Thu Oct 11 12:30:22 2001 URI=[index.jsp]
Thu Oct 11 12:30:22 2001 Initializing lastIndex=0 for a list of length=1
Thu Oct 11 12:30:22 2001 attempt #0 out of a max of 5
Thu Oct 11 12:30:22 2001 general list: trying connect to '160.50.106.101'/7162/7162
at line 1156 for '/index.jsp'
Thu Oct 11 12:30:22 2001 New SSL URL: match = 1 oid = 22
Thu Oct 11 12:30:22 2001 Going to check the general server list
Thu Oct 11 12:30:22 2001 WLS info : 160.50.106.101:7162 recycled? 0
Thu Oct 11 12:30:22 2001 Hdrs from Client:[connection]=[Keep-Alive]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[user-agent]=[Mozilla/4.72 [de]C-CCK-MCD
(WinNT; U)]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[host]=[btsun1a.muc:99]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept]=[image/gif, image/x-xbitmap,
image/jpeg, image/pjpeg, image/png, */*]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-encoding]=[gzip]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-language]=[de,en]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-charset]=[iso-8859-1,*,utf-8]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[connection]=[Keep-Alive]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[user-agent]=[Mozilla/4.72 [de]C-CCK-MCD
(WinNT; U)]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[host]=[btsun1a.muc:99]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept]=[image/gif, image/x-xbitmap, image/jpeg,
image/pjpeg, image/png, */*]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-encoding]=[gzip]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-language]=[de,en]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-charset]=[iso-8859-1,*,utf-8]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[WL-Proxy-SSL]=[false]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[X-WebLogic-Force-Cookie]=[true]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Client-IP]=[160.50.136.171]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[X-Forwarded-For]=[160.50.136.171]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Path-Translated]=[wwws/ns-homeV417/docs/index.jsp]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Path-Translated-Base]=[wwws/ns-homeV417/docs]
Thu Oct 11 12:30:22 2001 INFO: sysSend 52
Thu Oct 11 12:30:22 2001 Partial read socket
Thu Oct 11 12:30:22 2001 INFO: SSLWrite sent 0
Thu Oct 11 12:30:22 2001 INFO: Host (btsun2a.muc) doesn't match (160.50.106.101),
validation failed
Thu Oct 11 12:30:22 2001 ERROR: SSLWrite failed
Thu Oct 11 12:30:22 2001 SEND failed (ret=-1) at 549 of file URL.cpp
Thu Oct 11 12:30:22 2001 *******Exception type [WRITE_ERROR] raised at line 550
of URL.cpp
Thu Oct 11 12:30:22 2001 got exception in sendRequest phase: WRITE_ERROR [os error=0,
line 550 of URL.cpp]: at line 944
Thu Oct 11 12:30:22 2001 INFO: Closing SSL context
Thu Oct 11 12:30:22 2001 INFO: sysSend 14
Thu Oct 11 12:30:22 2001 Failing over after sendRequest exception
Thu Oct 11 12:30:22 2001 attempt #1 out of a max of 5
Thu Oct 11 12:30:22 2001 general list: trying connect to '160.50.106.101'/7162/7162
at line 1156 for '/index.jsp'
Thu Oct 11 12:30:22 2001 New SSL URL: match = 1 oid = 22
Thu Oct 11 12:30:22 2001 Going to check the general server list
Thu Oct 11 12:30:22 2001 WLS info : 160.50.106.101:7162 recycled? 0
Thu Oct 11 12:30:22 2001 Hdrs from Client:[connection]=[Keep-Alive]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[user-agent]=[Mozilla/4.72 [de]C-CCK-MCD
(WinNT; U)]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[host]=[btsun1a.muc:99]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept]=[image/gif, image/x-xbitmap,
image/jpeg, image/pjpeg, image/png, */*]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-encoding]=[gzip]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-language]=[de,en]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-charset]=[iso-8859-1,*,utf-8]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[connection]=[Keep-Alive]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[user-agent]=[Mozilla/4.72 [de]C-CCK-MCD
(WinNT; U)]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[host]=[btsun1a.muc:99]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept]=[image/gif, image/x-xbitmap, image/jpeg,
image/pjpeg, image/png, */*]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-encoding]=[gzip]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-language]=[de,en]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-charset]=[iso-8859-1,*,utf-8]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[WL-Proxy-SSL]=[false]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[X-WebLogic-Force-Cookie]=[true]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Client-IP]=[160.50.136.171]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[X-Forwarded-For]=[160.50.136.171]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Path-Translated]=[wwws/ns-homeV417/docs/index.jsp]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Path-Translated-Base]=[wwws/ns-homeV417/docs]
Thu Oct 11 12:30:22 2001 INFO: sysSend 52
Thu Oct 11 12:30:22 2001 Partial read socket
Thu Oct 11 12:30:22 2001 INFO: SSLWrite sent 0
Thu Oct 11 12:30:22 2001 INFO: Host (btsun2a.muc) doesn't match (160.50.106.101),
validation failed
Thu Oct 11 12:30:22 2001 ERROR: SSLWrite failed
Thu Oct 11 12:30:22 2001 SEND failed (ret=-1) at 549 of file URL.cpp
Thu Oct 11 12:30:22 2001 *******Exception type [WRITE_ERROR] raised at line 550
of URL.cpp
Thu Oct 11 12:30:22 2001 got exception in sendRequest phase: WRITE_ERROR [os error=0,
line 550 of URL.cpp]: at line 944
Thu Oct 11 12:30:22 2001 INFO: Closing SSL context
Thu Oct 11 12:30:22 2001 INFO: sysSend 14
Thu Oct 11 12:30:22 2001 Failing over after sendRequest exception
Thu Oct 11 12:30:22 2001 attempt #2 out of a max of 5
Thu Oct 11 12:30:22 2001 general list: trying connect to '160.50.106.101'/7162/7162
at line 1156 for '/index.jsp'
Thu Oct 11 12:30:22 2001 New SSL URL: match = 1 oid = 22
Thu Oct 11 12:30:22 2001 Going to check the general server list
Thu Oct 11 12:30:22 2001 WLS info : 160.50.106.101:7162 recycled? 0
Thu Oct 11 12:30:22 2001 Hdrs from Client:[connection]=[Keep-Alive]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[user-agent]=[Mozilla/4.72 [de]C-CCK-MCD
(WinNT; U)]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[host]=[btsun1a.muc:99]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept]=[image/gif, image/x-xbitmap,
image/jpeg, image/pjpeg, image/png, */*]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-encoding]=[gzip]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-language]=[de,en]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-charset]=[iso-8859-1,*,utf-8]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[connection]=[Keep-Alive]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[user-agent]=[Mozilla/4.72 [de]C-CCK-MCD
(WinNT; U)]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[host]=[btsun1a.muc:99]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept]=[image/gif, image/x-xbitmap, image/jpeg,
image/pjpeg, image/png, */*]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-encoding]=[gzip]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-language]=[de,en]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-charset]=[iso-8859-1,*,utf-8]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[WL-Proxy-SSL]=[false]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[X-WebLogic-Force-Cookie]=[true]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Client-IP]=[160.50.136.171]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[X-Forwarded-For]=[160.50.136.171]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Path-Translated]=[wwws/ns-homeV417/docs/index.jsp]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Path-Translated-Base]=[wwws/ns-homeV417/docs]
Thu Oct 11 12:30:22 2001 INFO: sysSend 52
Thu Oct 11 12:30:22 2001 Partial read socket
Thu Oct 11 12:30:22 2001 INFO: SSLWrite sent 0
Thu Oct 11 12:30:22 2001 INFO: Host (btsun2a.muc) doesn't match (160.50.106.101),
validation failed
Thu Oct 11 12:30:22 2001 ERROR: SSLWrite failed
Thu Oct 11 12:30:22 2001 SEND failed (ret=-1) at 549 of file URL.cpp
Thu Oct 11 12:30:22 2001 *******Exception type [WRITE_ERROR] raised at line 550
of URL.cpp
Thu Oct 11 12:30:22 2001 got exception in sendRequest phase: WRITE_ERROR [os error=0,
line 550 of URL.cpp]: at line 944
Thu Oct 11 12:30:22 2001 INFO: Closing SSL context
Thu Oct 11 12:30:22 2001 INFO: sysSend 14
Thu Oct 11 12:30:22 2001 Failing over after sendRequest exception
Thu Oct 11 12:30:22 2001 attempt #3 out of a max of 5
Thu Oct 11 12:30:22 2001 general list: trying connect to '160.50.106.101'/7162/7162
at line 1156 for '/index.jsp'
Thu Oct 11 12:30:22 2001 New SSL URL: match = 1 oid = 22
Thu Oct 11 12:30:22 2001 Going to check the general server list
Thu Oct 11 12:30:22 2001 WLS info : 160.50.106.101:7162 recycled? 0
Thu Oct 11 12:30:22 2001 Hdrs from Client:[connection]=[Keep-Alive]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[user-agent]=[Mozilla/4.72 [de]C-CCK-MCD
(WinNT; U)]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[host]=[btsun1a.muc:99]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept]=[image/gif, image/x-xbitmap,
image/jpeg, image/pjpeg, image/png, */*]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-encoding]=[gzip]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-language]=[de,en]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-charset]=[iso-8859-1,*,utf-8]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[connection]=[Keep-Alive]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[user-agent]=[Mozilla/4.72 [de]C-CCK-MCD
(WinNT; U)]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[host]=[btsun1a.muc:99]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept]=[image/gif, image/x-xbitmap, image/jpeg,
image/pjpeg, image/png, */*]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-encoding]=[gzip]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-language]=[de,en]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-charset]=[iso-8859-1,*,utf-8]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[WL-Proxy-SSL]=[false]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[X-WebLogic-Force-Cookie]=[true]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Client-IP]=[160.50.136.171]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[X-Forwarded-For]=[160.50.136.171]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Path-Translated]=[wwws/ns-homeV417/docs/index.jsp]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Path-Translated-Base]=[wwws/ns-homeV417/docs]
Thu Oct 11 12:30:22 2001 INFO: sysSend 52
Thu Oct 11 12:30:22 2001 Partial read socket
Thu Oct 11 12:30:22 2001 INFO: SSLWrite sent 0
Thu Oct 11 12:30:22 2001 INFO: Host (btsun2a.muc) doesn't match (160.50.106.101),
validation failed
Thu Oct 11 12:30:22 2001 ERROR: SSLWrite failed
Thu Oct 11 12:30:22 2001 SEND failed (ret=-1) at 549 of file URL.cpp
Thu Oct 11 12:30:22 2001 *******Exception type [WRITE_ERROR] raised at line 550
of URL.cpp
Thu Oct 11 12:30:22 2001 got exception in sendRequest phase: WRITE_ERROR [os error=0,
line 550 of URL.cpp]: at line 944
Thu Oct 11 12:30:22 2001 INFO: Closing SSL context
Thu Oct 11 12:30:22 2001 INFO: sysSend 14
Thu Oct 11 12:30:22 2001 Failing over after sendRequest exception
Thu Oct 11 12:30:22 2001 attempt #4 out of a max of 5
Thu Oct 11 12:30:22 2001 general list: trying connect to '160.50.106.101'/7162/7162
at line 1156 for '/index.jsp'
Thu Oct 11 12:30:22 2001 New SSL URL: match = 1 oid = 22
Thu Oct 11 12:30:22 2001 Going to check the general server list
Thu Oct 11 12:30:22 2001 WLS info : 160.50.106.101:7162 recycled? 0
Thu Oct 11 12:30:22 2001 Hdrs from Client:[connection]=[Keep-Alive]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[user-agent]=[Mozilla/4.72 [de]C-CCK-MCD
(WinNT; U)]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[host]=[btsun1a.muc:99]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept]=[image/gif, image/x-xbitmap,
image/jpeg, image/pjpeg, image/png, */*]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-encoding]=[gzip]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-language]=[de,en]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-charset]=[iso-8859-1,*,utf-8]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[connection]=[Keep-Alive]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[user-agent]=[Mozilla/4.72 [de]C-CCK-MCD
(WinNT; U)]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[host]=[btsun1a.muc:99]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept]=[image/gif, image/x-xbitmap, image/jpeg,
image/pjpeg, image/png, */*]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-encoding]=[gzip]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-language]=[de,en]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-charset]=[iso-8859-1,*,utf-8]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[WL-Proxy-SSL]=[false]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[X-WebLogic-Force-Cookie]=[true]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Client-IP]=[160.50.136.171]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[X-Forwarded-For]=[160.50.136.171]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Path-Translated]=[wwws/ns-homeV417/docs/index.jsp]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Path-Translated-Base]=[wwws/ns-homeV417/docs]
Thu Oct 11 12:30:22 2001 INFO: sysSend 52
Thu Oct 11 12:30:22 2001 Partial read socket
Thu Oct 11 12:30:22 2001 INFO: SSLWrite sent 0
Thu Oct 11 12:30:22 2001 INFO: Host (btsun2a.muc) doesn't match (160.50.106.101),
validation failed
Thu Oct 11 12:30:22 2001 ERROR: SSLWrite failed
Thu Oct 11 12:30:22 2001 SEND failed (ret=-1) at 549 of file URL.cpp
Thu Oct 11 12:30:22 2001 *******Exception type [WRITE_ERROR] raised at line 550
of URL.cpp
Thu Oct 11 12:30:22 2001 got exception in sendRequest phase: WRITE_ERROR [os error=0,
line 550 of URL.cpp]: at line 944
Thu Oct 11 12:30:22 2001 INFO: Closing SSL context
Thu Oct 11 12:30:22 2001 INFO: sysSend 14
Thu Oct 11 12:30:22 2001 Failing over after sendRequest exception
Thu Oct 11 12:30:22 2001 attempt #5 out of a max of 5
Thu Oct 11 12:30:22 2001 general list: trying connect to '160.50.106.101'/7162/7162
at line 1156 for '/index.jsp'
Thu Oct 11 12:30:22 2001 New SSL URL: match = 1 oid = 22
Thu Oct 11 12:30:22 2001 Going to check the general server list
Thu Oct 11 12:30:22 2001 WLS info : 160.50.106.101:7162 recycled? 0
Thu Oct 11 12:30:22 2001 Hdrs from Client:[connection]=[Keep-Alive]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[user-agent]=[Mozilla/4.72 [de]C-CCK-MCD
(WinNT; U)]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[host]=[btsun1a.muc:99]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept]=[image/gif, image/x-xbitmap,
image/jpeg, image/pjpeg, image/png, */*]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-encoding]=[gzip]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-language]=[de,en]
Thu Oct 11 12:30:22 2001 Hdrs from Client:[accept-charset]=[iso-8859-1,*,utf-8]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[connection]=[Keep-Alive]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[user-agent]=[Mozilla/4.72 [de]C-CCK-MCD
(WinNT; U)]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[host]=[btsun1a.muc:99]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept]=[image/gif, image/x-xbitmap, image/jpeg,
image/pjpeg, image/png, */*]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-encoding]=[gzip]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-language]=[de,en]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[accept-charset]=[iso-8859-1,*,utf-8]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[WL-Proxy-SSL]=[false]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[X-WebLogic-Force-Cookie]=[true]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Client-IP]=[160.50.136.171]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[X-Forwarded-For]=[160.50.136.171]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Path-Translated]=[wwws/ns-homeV417/docs/index.jsp]
Thu Oct 11 12:30:22 2001 Hdrs to WLS:[Proxy-Path-Translated-Base]=[wwws/ns-homeV417/docs]
Thu Oct 11 12:30:22 2001 INFO: sysSend 52
Thu Oct 11 12:30:22 2001 Partial read socket
Thu Oct 11 12:30:22 2001 INFO: SSLWrite sent 0
Thu Oct 11 12:30:22 2001 INFO: Host (btsun2a.muc) doesn't match (160.50.106.101),
validation failed
Thu Oct 11 12:30:22 2001 ERROR: SSLWrite failed
Thu Oct 11 12:30:22 2001 SEND failed (ret=-1) at 549 of file URL.cpp
Thu Oct 11 12:30:22 2001 *******Exception type [WRITE_ERROR] raised at line 550
of URL.cpp
Thu Oct 11 12:30:22 2001 got exception in sendRequest phase: WRITE_ERROR [os error=0,
line 550 of URL.cpp]: at line 944
Thu Oct 11 12:30:22 2001 INFO: Closing SSL context
Thu Oct 11 12:30:22 2001 INFO: sysSend 14
Thu Oct 11 12:30:22 2001 Failing over after sendRequest exception
Thu Oct 11 12:30:22 2001 request [index.jsp] processed ..................

I tried some other case and configured a certificate containing
the numeric IP as hostname. The authentication works fine then,
but it wouldn't be nice to hard-code the IP in the certificate
(btw. the WebLogicHost parameter is still given as DNS name, not
as IP address).
Has anyone got a solution for this?
"Wolfgang Jodl" <[email protected]> wrote:
>
I am trying to use SSL for communication between NSAPI and WebLogic
server (server authentication at the NSAPI).
Therefore, a custom server certificate is installed on WLS, containing
this
server's hostname. The NSAPI is configured (RequireSSLHostMatch=true)
to
check the hostname contained in the certificate against the WebLogicHost
parameter in the "obj.conf" file. The corresponding TrustedCAFile is
installed
for NSAPI.
The SSL setup seems to work ok, but when matching the hostname, it seems
like
NSAPI is trying to do a string-match against the numeric IP of the WebLogicHost,
not on the hostname as configured in the WebLogicHost parameter.
The relevant entry in the "obj.conf" file:
<Object name="weblogic" ppath="*">
Service fn=wl-proxy WebLogicHost=btsun2a.muc \
WebLogicPort=7162 \
Debug=ALL \
SecureProxy=ON \
TrustedCAFile=/home/qx13604/wls61/config/testdomain/TC_RootServer_PEM_Class0.pem
RequireSSLHostMatch=true
</Object>
I am using WLS6.1 with NSAPI (both Solaris). The content of "wlproxy.log"
is as
follows.
Any ideas?

FaceTime between Mac and iPad with one iCloud account?

I moved my MobileMe account to iCloud and want to set up my Mac so I can call my new iPad with FaceTime. In the iCloud system preferences I have "Mail and Notes" unchecked but the sole email account in Mail preferences is pointed to the iCloud mail server and I am receiving Mail. The account appears in Mail and seems to be functioing normally. If I check the "Mail and Notes" option in the system preferences a second iCloud Mail account appears in Mail with identical contents to the one that is there with this option unchecked. I'd rather not have this duplicate set of mailboxes in Mail so I'm leaving the option unchecked (is this OK?). I added my AOL address as a second email address to my Apple ID so I can use my AIM account with FaceTime and have set FaceTime to receive calls to my AIM address and I have added a contact with my iCloud email address.
On my iPad, I have set up FaceTime to receive calls to my iCloud email address and added a contact with my AIM address. This set up works when calling my Mac from my iPad but does not work the other way. How do I get it to work in both directions?
Thanks for any insights.

In partial answer to my own question, it seems that Mail and Notes option in iCloud system prefs on the Mac should be checked. The duplicate account that is then created in Mail (which points to the original account so it's not really a duplicate, as CS1sound pointed out to me) can be disabled in the Mail program prefs. This eliminates the dual mailbox sets in Mail.
Regarding the FaceTime calling between my Mac and iPad, that seems to have been resolved as well. The FaceTime iCloud account required more characters than the password for the old MobileMe account. This was unknown to me until I tried to view the iCloud account from within FaceTime preferences, when I got a message saying I needed a longer password. When I entered the new password it updated the FaceTime password and also updated my iCloud password (the password associated with my Apple ID). So now everything seems to be working nominally.
For others experiencing problems with FaceTime calling between Mac and iPad I suggest making sure your Apple ID password is at least 8 chars long, has letters (at least one cap) and at least one numeral. (This is the spec my FaceTime error message provided). Then attach an AIM address to your Apple ID as a "rescue" email address. Apple ID will send an email with a verification link to this address which must be clicked and this account will then be associated with your iCloud account (along with your original iCloud email address). Next, set the iPad up to use the iCloud email for Mail and FaceTime and create a FaceTime contact with (which receives calls to) the AIM address, for calling the Mac. Then set the Mac up to use the iCloud email address for Mail and set FaceTime up with the iCloud email, but with a "receives calls at" address pointing to the AIM account, then create a contact with the iCloud address, for calling the iPad.
Posted this because I saw others have had the same problem. Sorry for the verbosity but this is just a blow by blow recounting of what I did. I hope some of the board gods and moderators will vet this for mistakes. I don't want to mislead any fellow pilgrims, but it worked for me .

Wich is table for match between Infoprovider and update with technical name

Thanks in advance!
Bye!
Ferdinando

Hello ,
You can check table --> RSUPDINFO table for Update rules with tech ID between Cube and InfoSources.
and other ref tables are --> RSUPDROUT / RSUPDDAT / RSUPDKEY /
--EnjoySAP
**Award credits if you are done with my answer

I'm shopping for an iPad. What is the difference between Wifi and Wifi with cellular/3G?

I'm shopping for an iPad. What is the difference between Wifi only and Wifi with cellular/3G?

Depending from what do you want. The only WI-FI iPad have wireless connection. The WI-FI plus cellular/3G have wireless connection and celular/3G connection to call everyone and the mobile data for internet but the software is same.

Difference between VMI and collaboration with customer

Hai,
I am trying to understand the difference between VMI and collaborative planning with customer(CPC)
Please correct me if I am wrong. In VMI, a vendor or manufacturer sells his material to customer and through EDI, the customer gives the information such as forecast, stock etc.
In CPC, the vendor and customer interchange information, such as demand, stock levels, promotions, delivery dates etc., based on ITS.
What is the difference between these two?
If I am not wrong, EDI is used for outside company communication andITS for within. So, can I say that VMI is for customer outside the company and CPC for internal customer?
Thank you.

Hi Visu,
Service provided by a vendor for a customer, whereby the vendor plans material requirements in the customer's company. Vendor-managed inventory is only possible if the vendor has access to the customer's current stock and sales data.
In the ERP system, the following functions are available for vendor-managed inventory:
Transfer of stock and sales data by EDI
Receipt of stock and sales data by EDI
Replenishment planning for customers
Creation of a purchase order for an external EDI order acknowledgment
supply chain management tool that synchronizes demand signals and supply chain activities by utilizing Internet technology. Collaborative Planning enables supply chain partners to view, share and synchronize common information within the supply chain.
Hope this helps.
Regards,
Mohan

Difference between Scheduled and released with respect to process chains

HI All,
I am Creating a cube in whcih I want to upload the current status of the process chain.
And the requirement is not to take those process chains whcih are scheduled and not released( only take those process chains whcih have status released)
for the same I dont know what is the difference between Scheduled and Released in respect of process Chains and also from whcih Database table I can get this information.
Please help.
Regards,
Ujjwal

Hi,
Job Status Scheduled means a job has been created and is ready to run but has not yet been triggered.
A release status means the created job has been triggered and is waiting for the opportunity to run. A job can be in released status when it is a periodic Job ( Where once the job is completed it goes to release status), when it is slated for future execution, or when there is a delay due to database overload.
Regards,
Pramod

Diff between Discount and Rebate with configuration Step of rebate

Waht is the deffrence between discount and rebate in SD , Pls provide the Rebate configuration Step

provide the Rebate configuration Step
Please avoid asking like this. Before posting, please search the forum and try on your own.
Coming to your question,
Waht is the deffrence between discount and rebate
discount is as and when you generate billing documents, straightaway, you offer discount on the invoice value, whereas, rebate is once you reach the agreed sales turnover, some percentage of value would be created once in a year or twice depending upon the agreement.
thanks
G. Lakshmipathi

How to share structure with arrays in a single file between C# and C with arrays?

It is possible to define things so that a file that contains a struct definition can be included in both C# and C programs once the differences are taken into account. Most of these differences can be handled but not all. One of those problems is arrays.
Here's a contrived example of a file that can be imported directly into either a C or a C# project. If '__c__' is defined then the file is being imported into a C++ project. If not then the file is being consumed by a C# project. This simple little
thing allows those things that are different between the two environments to be taken into consideration. The one really knotty problem is how to handle arrays. In C, an array can be given a fixed size in a struct. Not so in C#. C# generates a compile time
error. I've been working around it so far by numbering the elements in the C# branch.
// If '__c__' is defined then the file is being included in a C project.
// If not then the file is being included in a C# project.
#if !__c__
// C# can utilize a namespace. C cannot.
namespace CrossPlatform
// C# wants to include the struct in a class.
public class Structs
#endif
#if __c__
// C defines a struct as a named typedef.
typedef struct _RtInfo
#else
// C# wants a struct object with a name.
public struct RtInfo
#endif
// Simple value types and previously defined structures
// can be shared directly between both C and C#.
float f;
#if __c__
// Arrays cannot be shared. C can use arrays with a size.
int v[4];
#else
// but C# cannot deal with sized arrays at all.
int v0;
int v1;
int v2;
int v3;
#endif
#if __c__
// C optionally gives the struct a name.
} CALDATA;
#else
// C# does not do that here.
#endif
#if !__c__
} // end of class.
} // end of namespace block wrapper.
#endif
Richard Lewis Haggard

Hi
Richard.
Would you mind letting us know the result of the suggestion?
I temporarily mark
Viorel’s last response as an answer. You can unmark
it if they provide no help.
Best regards,
Kristin
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

EoMPLS Xconnect between 2811XM and 7606 with RSP720

Similar Messages

Maybe you are looking for