Epson 1280 printer & 10.8.2: print quality/color problems?

hi, I just upgraded to an iMac with Mountain Lion, and was told that my older, beloved Epson 1280 would be fine.
I followed instructions to update driver through Apple (did not touch original epson installation cd...went directly through apple), and I've been doing test printing today and the image quality & color quality is not good at all... any troubleshooting advice would be greatly appreciated!
I was used to the window where I could control the Epson print settings on my old mac, and I can't seem to find similar window/settings on this
new Apple driver upgrade. Sorry if I've overlooked something basic, I'm still learning on the new OS...
I'll need to keep my old mac for higher quality printing if I can't improve results on the iMac...
thank you so much for any advice!

There are basically two places to control the printer and print quality. One of these two should work for you.
Open System Preferences (under the Apple logo in the Menu Bar), and click "Print & Scan". Find your printer there and click "Options and Supplies". Maybe you can set up what you like there.
As you issue a "Print" command from some app (e.g., Safari), you will see a "Show Details" button in the lower left. You can make many adjustments there; perhaps one or more is what you're looking for.

Similar Messages

Print quality color laserjet 2600n

The company I work for has a Color LaserJet 2600n. We continually run into a problem with the print quality. When we print a demo page, the colors seem fine. Then we try to print a document or handout that has color in it, and the edges along the sides of the paper fade and the colors seem spotty, at best, and usually the colors are faded. I have even tried changing the printer properties to lighter, heavier and even glossy paper, and ther is just no discernable difference in quality. I have also cleaned the printer and changed the ink cartridges and, again, there are no differences. The colors simply seem to fade near the edges of the paper. Is there anything that can be done?

Hi balaspa; Hope you are doing well;
Your HP laserjet 2600n is a commercial product. I will suggest posting in the forum for HP Business Support for a better chance at finding a prompt solution.
You may find the commercial Laserjet board here.
http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
Best of luck;
RobertoR
You can say THANKS by clicking the KUDOS STAR. If my suggestion resolves your issue Mark as a "SOLUTION" this way others can benefit Thanks in Advance!

Printer quality/colors not accurate since installing Yosemite

I recently upgraded to OS 10.10, Yosemite. I can no longer get accurate colors printed for photos from Photoshop. I have Photoshop CS4 and I use an Epson Stylus Photo R2400 printer. I am able to use Photoshop for everything but printing accurately. I downloaded all recommended drivers for the printer, reloaded profiles for the printer and even tried a trial of Photoshop CC. Nothing resolves the problem. My prints look kind of solarized. Black and white photos have green areas where there should be black. Please help.

Try resetting the printing system.
OS X Mavericks: Reset the printing system Yosemite

Epson Photo Printer 2400 Color Management

I cannot get my photos color and vibrancy to print on this printer. I have tried 5 profiles so far. Anyone have ideas on how to make this happen. What profile or devises might help me? I downloaded the matt and luster profiles but can't find them. Where are they supposed to be on the harddrive. Thanks delish

Having turned off the Epson colour management, you need to ensure you have selected the correct colour profile in CS3. It helps to calibrate your monitor correctly and use a profile designed for your printer / paper / ink combination to ensure what you see on the screen is what feeds out the printer. Paper brand can make a startling difference. There are companies that offer a profiling service. You print out a pecific photo / pattern from their provided file and send them the print on the ink / paper you use and they email a profile.. Google will find these companies for you.

Epson R3000 printing wrong colors after Apple software update from 24th January

I updated the EPSON driver version 2.16 within the Apple Update. Now the colors are wrong. I restored Library\Printers\EPSON from Time Machine with date 18th January. But I have still the problem.

Hi pilotmicha,
Thanks for visiting Apple Support Communities.
Try these troubleshooting steps if your printer is not behaving correctly:
Delete the affected printer, then add the printer again.
If the issue persists, try these additional steps:
Reset the printing system, then add the printer again.
If the issue still persists, reset the printing system again. Download and install your printer's drivers. Then, add the printer again.
Contact the printer vendor or visit their website for further assistance.
You can find these steps and more information here:
Troubleshooting printer issues in OS X
http://support.apple.com/kb/ts3147
Best Regards,
Jeremy

6980 print quality (odd problem)

A 6980 is giving smeared or partially missing characters within the first six lines of text. It shows up in either the beginning or end of the line, no regularity to beginning or ending position. Graphics are not affected. The rest of the page is perfect. It is a new black cartridge. No error message is displayed, good quality paper is used. The defect does not go beyond ten characters in any line. It predominantly afffects the first two or end two characters. The problem first appeared when the previous cartridge was in use, that is why the cartridge was replaced. Normally, this type of defect will be seen in all lines and therefore, cartridge replacement fixes it. No so this time. My 35 years experience as a computer technician cannot solve this one.

I purchased my Pro K5400 in May 2008. In the beginning it was loud (still is) but the printing was beautiful. Over the last three months the color printing is really bad. I've replaced the cartridges with only HP ink, I've aligned printheads, I've cleaned printheads, I've calibrated the linefeed. The diagnostic suggests I replace the printheads. Really? After less than a year? It also sporadically feeds several pages at once. And, I do a lot of printing of claim forms, it arbitrarily expands the left margin. Oh, it also jams often. Again, I believe these last two are due to a feeding problem. I sent an online question and got answers back in somewhat broken English that seem hooked on just replacing the ink and cleaning the printheads. Also, they gave me directions on how to clear a jam. This I know as I clear jams all the time in this printer. They are unable (perhaps due to language barrier) to answer the feeding/jamming problems. I really see this as just a very bad quality printer. I've owned other HPs and never had problems like this. What is the best way to contact someone in the United States about this printer?

Photoshop does not recognise my epson 9800 printer

I've been using CS6 for a long time(Years) with my Epson 9800 printer without any problems. Today between two prints it now comes up with an error message. Anybody else have this problem?

Dear alderman,
Yes, I had a problem too, but with a different Epson printer and while trying to print from an Adobe PDF file. No error message, just NOTHING! The problem started after I installed the latest Epson update. The print jobs would just keep stacking up and not print. After many tries I finally got everything working again by printing something from my Pages application that did not come from an Adobe PDF file…that seemed to get everything working again. Going into the System Preferences on my Mac (10.7.5) and deleting jobs, restarting the printer, etc., did not seem to help, but printing from Pages (or another word processing application) did the trick. You might try it.

Epson 1280 - can't select media type or print quality

I just went Mac and got the imac w/ OS 10.6
I downloaded the drivers for my Epson 1280 - I can't find a way to select my media type (photo paper, etc) - nor can I find how to change my print quality (high quality vs draft).
Has anyone figured this out?
betsy

Your browser/File/Page Setup
nor can I find how to change my print quality (high quality vs draft).
Not to sure where this setting is. Never seen it. Try your browser/File/Print/Printer - click on the far downward triangle. Any settings there you can play around with?

Epson shared printers- can't control print quality

Hi someone,
We have an espon stylus photo 1280, and an epson stylus photo R200.
Both are connected to one Intel iMac via USB.
We have 2 other Macs - one iMac G5, and Mac mini G5 which are sharing these printers. All have the latest Tiger OS 10.4.6.
They print fine, but the problem we're having is that the 2 computers which are using the printers via the network do not have access to Epson's special utilities when in the print dialogue screen - ie: they cannot change the print quality, paper stock, black vs colour etc. when just about to print.
The only one that does have access to Epson's controls is the one which is connected via USB.
We also can not see the printers from the other 2 macs in the Printer Browser when searching for them using appletalk, or epson appletalk etc....only in the Default Browser as "Shared Printers"
Does this have something to do with it?
How can we get the 2 Macs which are using the printers as "shared printers" access to the epson print options?
thanks!
Intel iMac, iMac g5, Mac mini Mac OS X (10.4.6)

Are your printers "networked" as in using ethernet, or are they simply shared, using the OSX shared printers feature? I think it makes a difference.
I had a similar problem. My printer, an Epson 1280 is connected to mu iMac G4 via USB, and is shared by my MacBook Pro. I was unable to access the Epson print utility features that allow setting quality, borderless prints, etc. I contacted Epson and they sent me the following fix. it took care of the problem. I can change the settings from either the primary iMac or from the shared printer on the Laptop.
To correct the issue you are experiencing, we will perform a complete
removal of the files and reinstall the driver.
REMOVE FILES
1. Double click on the MAC HARD DRIVE
2. Double click on the LIBRARY folder
3. Double click on the PRINTERS folder
4. Drag the EPSON folder to the trash can
NOTE If you receive an access denied error message, this indicates that
you do not have root access. You will need to contact Apple for assistance
on obtaining Root Access.
1. Insert your 10.4 CD/DVD, double click on the CD/DVD icon on your
desktop.
2. Double click SYSTEM > INSTALLATION > PACKAGES > EPSON PRINTER
DRIVERS.PKG
Follow the prompts for the installation, restart your Mac when complete
Please follow the steps below to install the resident driver for your
printer in OS 10.4:
1. Make sure that your printer is turned on and connected to your computer.
2. Open your PRINTER SETUP UTILITY. This is found in HARD DRIVE,
APPLICATIONS, UTILITIES directory
3. If there are any entries for your printer click on them and hit the
DELETE. Once they are all gone Click ADD, then MORE PRINTERS at the bottom
of the printer browser.
4. In the window that appears, select EPSON USB from the drop-down menu at
the top, then highlight your printer when it appears under NAME , under
PAGE SETUP select ALL, and then hit ADD.
5. Quit out of the printer setup utility and try printing from any OS X
application.
To set up your printer for borderless printing in OS X please follow the
steps below.
After you have installed your printer driver for OS 10, you will need to do
the following to add extra paper features such as borderless printing
options:
1. Go to Printer Setup Utility (found in HD > Applications > Utilities).
Delete any existing references to the Epson printer from the list.
2. Go to Add. Select Epson USB for a USB printer or Epson Firewire for a
Firewire-connected printer.
3. Highlight the printer name when it appears under Product. Under "Page
setup" use the up-down arrows and select ALL.
4. Click Add. The new printer options will now be added to the Printer
list; you will see the printer name numerous times with different paper
selections attached. (If you are unable to see the full description you
will need to extend the name category.)
5. Highlight the printer name/feature which you wish to use (For example,
"Stylus Photo 2200 (Sheet feeder-Borderless)") and make it the default.
Close Printer Setup Utility.
6. Ensure Classic is not running. Open an OS X application and the file you
wish to print.
Setting up borderless prints in an OS X application (NOTE: not all
applications will show these options)
1. Click on FILE and PAGE SETUP. Ensure the settings below are adjusted:
SETTINGS: PAGE ATTRIBUTES
FORMAT FOR: EPSON STYLUS XXX XXX(BORDERLESS)
PAPER SIZE: Whichever compatible paper size you wish to use
(NOTE: borderless printing is not supported on custom paper sizes.)
Click OK when done.
2. Click on FILE and PRINT. Ensure the settings below are adjusted:
PRINTER: Stylus XXX XXX(BORDERLESS)
PRESETS: STANDARD
Make any other adjustments needed (on COPIES and PAGES, PRINT SETTINGS,
etc) and then click PRINT.
Good Luck!

10.5 with Adobe CS2 and epson 1280 - no printer dialogue box

I have recently upgraded from Tiger to Leopard and now when I run Photoshop CS2 and try to print on the Epson 1280, there is no choice for paper quality and other settings. It just prints and it is just awful.
I have the latest drivers installer (CUP and Guten).
I also have CS3 put that wouldn't work with any Epson printer and had to de-install it (year ago).
Garyvp

John,
In photoshop, the triangle jut opened up the main parameters box. In there is a 'printer features' button this is where the media selection is. They changed the tags. Thanks for the help.
GVP

Print quality with Aperture and Epson RX580

Hi all,
I feel like I've tried everything, but I just can't get Aperture (the latest version with all the updates) to print from my MacBook Pro on my Epson photo printer the way I could from other photo software on my old PCs. On my old PCs, when I would print a photo from Canon DPP or Capture One, or even the Windows photo management software, I get a rich menu of dialogue boxes for the Epson printer offering different qualities of prints, different papers to choose from, "photo enhancement," and lots of other options. Prints came out sharp, colorful, and just great.
When I print from Aperture, I get none of these options (I get color management and resolution, and that's about it).
When I print from Aperture, I get vertical lines in the prints, visible dots, and pixellation. So what I do is email the "exported" versions to my daughter's PC laptop and print from there -- and get good results. Boy, that's a pain.
Surely Aperture can do better than this. So what am I missing? Any ideas for what I should be doing?
Thank you.

Canon MP990 and Macbook pro (os X snow lep.. and Lion) - Lines in prints in Aperture.
While a bit vague I got there and found the distinction between the printer driver managing it and the printer managing the photo quality causing the issues.
I could only transfer the pic's to iphoto and print for ( admitedly about the same time of more than a year).
The FIX
in the first window after selecting print scroll down to rendering and select printer managed.
Select all the other settings you need then select print on the right bottom of this window.
This next dialogue box at the bottom is a show details button then a new set of menus are present (initial is layout in a pull down menu) select color matching then automatic ( you can change this but it worked so if it is not broken I'll play later ).
You should have clear prints with no lines...

Print quality on Epson Stylus Photo R800

Hi...
I'm using Lightroom 3.6 and an Epson Stylus Photo R800. This printer is capable of printing very high quality pictures, as I know by using it for almost 5 years.
I have bought Lightroom about 6 month ago. I have tried anything I can think off to get those fabulus pictures out of my Epson printer. I alterd color managment settings, changed print resolutions, downloaded new printerdriver, ... Nothing works. Print quality when printing from Lightroom is very poor. Bad colors (dark), stripes over the whole image, it looks like nothing realy.
One of the things that I noticed is that the maximum resolution for printing in LR is 720 ppi. My Epson is capable of 1550 ppi.
I see a lot of discussion going about print quality with lightroom... I think however this is a more basic problem. My print qualiti is realy very very bad...
Does anyone have similar problems or (even better) a hint to a solution?
Note,
When I export a picture to .jpg format (I shoot in RAW only), and print this directly from Windows, I do get the perfect picture a was used to... I cannot believe that Lightroom is unable to do the same.
Thanks!
Erik.

Sorry for calling you 'Frank' Frans...
Vriendelijke groet,
Erik Henken.
Op 3 jan. 2012 om 20:23 heeft "c.frans w" <[email protected]> het volgende geschreven:
Re: Print quality on Epson Stylus Photo R800
created by c.frans w in Photoshop Lightroom - View the full discussion
I would shine some light on your remark:
One of the things that I noticed is that the maximum resolution for printing in LR is 720 ppi. My Epson is capable of 1550 ppi.
I see a lot of discussion going about print quality with lightroom...
My name is :
Frans
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4116097#4116097
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4116097#4116097. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Photoshop Lightroom by email or at Adobe Forums
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

EPSON Stylus Color 1160 changing default print quality under 10.4

Greetings.
I have the above printer and since Epson no longer produces a driver that will function under 10.4 I am using the Gimp driver. Which works fine.
The printer is connected to our server and so functions as a ‘shared printer’ in the network. The server runs 10.4.8.
However I would like to tweak the default settings for all users.
One of the things we use this printer for is to make drafts for checking text or layouts. The default setting is for an excellent print quality. I would like to change this to a lower resolution (saves ink > saves money > saves planet > reduces carbon footprint, ;-)))
Anybody knows how to do this?
Thanks

Greg good morning,
It did solve it partly. Here is what I have now. If printing directly from the computer the printer is connected from now is no problem, the settings have changed.
However as this is my server (the Epson is connected to it via USB) printing from the other machines have not changed the standard dialog box.
When I try access the Epson setup via http://127.0.0.1:631/printers on the individual computers I get:
Forbidden. You don't have permission to access the resource on this server. <</div>
Any suggestions as to how to solve this so I have there also the standard box changed? Reason is of course that on the individual computers the dialog is generated locally and their settings are following the standard rule than send to the printer, bypassing the setting of the printer. So question is, how to get in to this dialogue?

The photo print quality from my Mac to my Epson Artisan 810 is poor. When I take the same photo files (JPEGs) to my PC to print to the same printer without even uploading them to the PC, they print brighter and crisper from my PC.

The photo print quality from my Mac to my Epson Artisan 810 is poor. I just purchased my iMac for my photography business in Jan. (this is my first Mac). When I first tried printing, I noticed the quality wasn't as good as I expected it to be. Then, I had to print 4-3.5x5s on a sheet, so I e-mailed the image to myself and opened it on my PC to print it (much easier to print that way on PC in Windows Photo Gallery - I think it's impossible to print that way in iPhoto). That's when I first noticed that when I take the same photo files (JPEGs) to my PC to print to the same printer without even uploading them to the PC, they print brighter and crisper from my PC.
I've already been on the phone and e-mail w/Applecare many times over this issue. We've tried creating a test user and printing from there, and we've tried reinstalling the OS. I've tried printing from iPhoto, ImageCapture, and Preview apps/utilities, all w/the same result - no comparison to the PC-printed versions (no enhancements have been performed on the PC).
I'm out of ideas, and so is Applecare. They say it's most likely a driver issue b/c the printer is outdated, and that the only solution is to buy a new printer. BUT it is a pain for me to purchase a new printer - it takes days of research due to the nature of my business and the fact that I need a printer that can print directly onto a disc. I love this printer and don't want to have to buy a new one if I don't have to.

englishfreak2004 wrote:
Yes. I've checked for updates, and the driver I installed is the same as the one on Epson's website. I also spoke with Epson Customer Service, which was a dead end. Apple says the problem is due to an Epson driver issue (blaming Epson), but Epson says that with the older printers, it's actually Apple who creates the driver, so the problem is actually with Apple. Typical he-said, she-said...
Maybe not. Probably worth checking here:
Epson drivers for Mavericks:
http://www.epson.com/cgi-bin/Store/support/SupportMavericks.jsp

Poor print quality with Epson Photo R265 - Please help

I am changing over from Windows to Mac and finding it 'challenging' - it's me; not the mac (which I love)I'm sure, so any help would be much appreciated.
My problem is: when I plugged my usb into the mac it instantly recognised my printer but when I printed a photo from iPhoto the quality was very poor with faded colours and faint lines.
I went hunting for an answer, and convinced I'd found it, I downloaded the latest drivers from Epson but on reprinting...exactly the same problems.
The on-screen quality is superb but on paper it's poor.
I'd really appreciate any suggestions or help. I'm not at all knowledgeable when it comes to computers.
thank you
Caroline

Both programs print very poorly. Either light and faded or streaker, or if I change the settings, very dark. Both useless. Frustrated I tried the same pics on Picassa on my Windows notebook. Quality was excellent. Put Picassa on the iMac and it now works great - in Picassa. how can that be?

Epson 1280 printer & 10.8.2: print quality/color problems?

Similar Messages

Maybe you are looking for