Epson LX-300+II with

Dear Gurus,
                       I had Created printer in SAP with following parameter as per Note 153879 - EPSON printer model and SAP device types
                                 Device type :EPESCP9
                                 Access Method :G
                                 host printer :_default.
There is is page format which is assign to EPESCP9.
it print successfully. But It does not print Tables AND BOXES . Please solve my issue

What type of Dot Matrix printer is that 9PIn or LQ-55 ? Please try below device type first for 9 or 24/42 dot matrix printer
EPESCP
EPESCP2
EPESCP9
Set the print quality to 120 X 144 DPI in the printer properties.
Refer to the Note 153879 - EPSON printer model and SAP device types
Note 8928 - List of supported printers/device types - Provide appropriate driver according to your printer type and try again.
Note 153879 contains information about compatible printer models from the manufacturer EPSON.
Thanks,
Arjun
Edited by: Arjun Venkateswarlu. on Jan 31, 2012 9:31 PM

Similar Messages

Epson LX-300+II with sap

Dear gurus,
                     I had setup epson LX-300+II with sap with following parameter
                                  Device Type :EPESCP9 :EPSON ESC/ P 9PIN PRINTER
                                  host spool Access method : G:Front End Print with Control Tech
                                  Host Printer:_Default
                   there is a page format which is assign to EPSCEP9.
Print successful. but it will no print Table and box on the page...Please solve my Issue.....
Thanks in Advance,
Regards,
Snehal Patel

My guess would be that the device type definition is missing the print controls that you need.
I don't know that particular printer type but try to look into the device type-dependent print controls defined in txn. SPAD and see if it contains the controls to draw a box etc. If not, then you will probably have to copy and enhance the print control set.
Hopefully you do have the detailed manual for the printer...

Does a Epson LQ 300 work with a Macintosh Se

Would a Epson LQ 300 printer work with a Macintosh Se that has system 6.0.8 and finder 6.1.8?

What printers will work with your SE?
For the SE to use a printer, it needs to have the printing software for that model of printer.
The software for all Apple printers manufactured at the time of System 6.0.8 can be found on the System 6.0.8 installer diskettes. (This includes all ImageWriters and a few LaserWriters.) In fact, this software is installed by default if you did an easy install instead of a custom install.
The printing software for most other Apple printers can be downloaded here:
[http://download.info.apple.com/AppleSupport_Area/Apple_Software_Updates/English-NorthAmerican/Macintosh/Printing>
Also look here:
[http://www.info.apple.com/support/oldersoftwarelist.html#print]
The software for non-Apple printers has to be installed with a separate installer. You can usually find this on a disk that comes with the printer.

Printing Problem with EPSON LX 300+

Dear all,
I have met a problem with Epson LX 300+. After I set up printing on PLD, the result printing is bad. Font and setting are not the same as preview in SBO. How to solve this matter..? I used SBO 2005A PL 43.
Thanks for your help....
Regards,
agung
Edited by: Agung Adrianto on Aug 28, 2008 8:17 AM

Hi Agung,
Here is a way out for the issue you have submitted. I can't guarantee that this wayout work perfectly:
Question:
As we know that the dos matrix printer supports dos prompt and thus printing speed and
life of the printing head is comparatively more than what we print the same in graphical format.
So when I tried to print from SAP Bone in dot matrix printer, the printing speed is very slow and quality of printout is not good enough.
Any clarifications on this regard would prove very helpful to me.
Regards,
xxxxx
Consultant Business solutions.
Solution:
Do you use one of this printer types:
Dot Matrix, Printer, Needle Printer, Citizen ProDot 300 , Oki Microline, Epson FX880, Epson FX890 ?
Here the stepwise I have tried :
In order to print using Dot Matrix printers, follow the below
instructions:
1. Run SAP Business One.
2. Click the upper menu 'File' and select 'Page Setup'.
3. The Print Setup window opens. Under 'Paper', in the field 'Size', select 'Letter' from the drop down menu.
4. Click OK to confirm your selection.
5. On your desktop, click Start => Settings => Printers.
6. Right click on the required Dot Matrix printer and select 'Printing Preferences...'.
7. Click the 'Paper/Quality' tab page and click the 'Advanced' pushbutton.
8. Under'Paper/Output'=> 'Paper Size', click on the underlined paper size(e.g. A4) and select 'Letter' from the drop down menu.
Note that if you leave the value 'A4', each page will be spreaded over 2 pages when printing using Dot Matrix printers.
9. Under 'Graphic'=> 'Print Quality', click on the underlined value (e.g. 230X250 dots per inch) and select '120X144 dots per inch' from thedrop down menu.
Note that in case the value '120X144' is not available you should select a similar value from the list.
I did not test it yet and I am not so sure about the result but you could test it.
Rgds,

Printing Problem with Epson LX-300+ii and LX-310 in Windows Server 2012 R2 64-bit

I recently installed Windows Server 2012 R2 64-Bit.
We have Printer Epson LX-300+ii and LX-310 (dot-matrix) that we share among users. Each user access the Server using Remote Desktop. From previous experience with Windows Server 2008, I knew that these printers will be problematic, especially regarding
the Easy Print driver.
And I was right, using the Easy Print driver, I got the following result:
And so, I did manual mapping & disable the "Use Remote Desktop Easy Print printer driver first". Haha, what a surprise, I got the following result:
And so I uninstalled the printer driver, and install it again, thinking that I might chose a wrong driver, but.... same result. I know for sure that I chose the correct driver.
Next, I tried connecting the printer DIRECTLY to the server. Log-in to the Server directly,
not using Remote Desktop. And tried printing again, haha... really... what a surprise... I got the same problem here !!!
So now I know the problem is not the Easy Print driver, not mapping or registry problem either. It's the print driver. This is SUPER FRUSTRATING, I tried the same driver from the same CD in Windows 8.1 64-Bit with no problem. I tried it too in Windows 7
32-Bit with no-problem either. But somehow, this driver is problematic in Windows Server 2012 R2.
Any help? Anybody else bump into this same problem ? I'm close to giving up, been spending too much time figuring out this damn thing.
Andy

Hi Bulent Sahin,
Thank you for your reply, I tried IBM Graphics driver, but the result is equally as bad. But your answer inspire me to try different drivers. And so, the closest & best driver that I could use now is EPSON ESC/P 9pin V4 Class Driver
It's not as good as I would expect, but at least now, it's acceptable & readable. I can't believe that I'm the only one who have this problem
Thank you Mr. Sahin

Problem with character mode printing on epson lx-300

Greetings
I developed a character mode report and is printing fine on the printer lx-300 when I use Reports 6i (Client/Server)
We migrated all the platform to OAS 10G Release2 bu the same report has the following behaviour:
1. The left margin is shift to lthe right about 2 inches.
2. Is printing shrinked and the characters doesn't see well.
The report is a character mode report of (132 columns, 66 lines).
I set the default prt to:
printer "dflt"
height 66
width 132
after page control(L)
return ""
linefeed control(J)
The run parameters are mode=character and desformat=dlft.prt
Anybody has experience using character mode reports on 10g on matrix printers like epson lx-300?
Thanks!

Hi Agung,
Here is a way out for the issue you have submitted. I can't guarantee that this wayout work perfectly:
Question:
As we know that the dos matrix printer supports dos prompt and thus printing speed and
life of the printing head is comparatively more than what we print the same in graphical format.
So when I tried to print from SAP Bone in dot matrix printer, the printing speed is very slow and quality of printout is not good enough.
Any clarifications on this regard would prove very helpful to me.
Regards,
xxxxx
Consultant Business solutions.
Solution:
Do you use one of this printer types:
Dot Matrix, Printer, Needle Printer, Citizen ProDot 300 , Oki Microline, Epson FX880, Epson FX890 ?
Here the stepwise I have tried :
In order to print using Dot Matrix printers, follow the below
instructions:
1. Run SAP Business One.
2. Click the upper menu 'File' and select 'Page Setup'.
3. The Print Setup window opens. Under 'Paper', in the field 'Size', select 'Letter' from the drop down menu.
4. Click OK to confirm your selection.
5. On your desktop, click Start => Settings => Printers.
6. Right click on the required Dot Matrix printer and select 'Printing Preferences...'.
7. Click the 'Paper/Quality' tab page and click the 'Advanced' pushbutton.
8. Under'Paper/Output'=> 'Paper Size', click on the underlined paper size(e.g. A4) and select 'Letter' from the drop down menu.
Note that if you leave the value 'A4', each page will be spreaded over 2 pages when printing using Dot Matrix printers.
9. Under 'Graphic'=> 'Print Quality', click on the underlined value (e.g. 230X250 dots per inch) and select '120X144 dots per inch' from thedrop down menu.
Note that in case the value '120X144' is not available you should select a similar value from the list.
I did not test it yet and I am not so sure about the result but you could test it.
Rgds,

Printing Cheque using EPSON LX-300

Hi Everyone,
Could you please help me with this issue?!
I had implemented the Cheque process but when I am using EPSON LX-300 printer an error occurs. Some numbers and letters are showing up on the begining of the line. I think that this is because of printer configuration.
On the Spool transaction the cheque is nice.
Do you know how I can solve that?
Thanks
Daniel Dorta

hi
set the margin either in the Print out or in the printer configuration.

EPSON LX-300+II printer

Hi,
We are implementing ECC6.0 and now we are doing printer configuration. We have EPSON LX-300+II dot matrix printer. And we have created a output device ZLP01 but we haven't found this printer in the device type list. So we have choosen nearest printer KPKS: EPSON Dot-Matrix KS, device class standard printer, Host spool access Method G:Front End Printing with Control Tech., Host Printer _DEFAULT.
But it is printing some junk numbers like f460y2X0y2X0y2X0y2X0y2X0y
So, please help me to configure my printer.
Regards,
Nilesh

Hi Nilesh,
This is SAP Business One forum.
Close this thread and re-post your question to a correct forum
Regards,
Bala

Epson LX-300, Epson FX-890 printers in Windows Server 2008 x 64 and Windows 7 (x32 and x64)

I have the following problema working with RDP connections to Windows 2008 Server (x64) SP2 and Windows 7 Professional (x32 & x64).
I have setup correctly an Epson LX-300, LX-300+, LX-300+II and FX-890 printers in separate computers in Windows 7 (all working under Windows 7 Professional x64 and x32) and they work correctly.
I need to RDP to a Windows 2008 Server SP 2(x64) and once I log in, the Server Operating System recognizes my printer with no problem at all (Redirected Printer), but when I print, the characters and not understandable, since the printed information is blurry.
When I do excatly the same procedure but with a Client with Windows XP installed the printed information is totally clear, so we can determine at least that the printers are working fine.
I understand this should be a driver issue, but i simply can't make it work correctly.
Can anybody help.

Hi,
Since the printer can print the test page, there is no need to collect the Event log. I notice there is no specify driver for Windows 7 and Windows Server 2008. It seems the default Easy Printer driver doesn’t work properly for these printers.
I suggest you install the Windows Vista driver version on the Server for testing.
LX-300 Impact Printer
LX-300+ Impact Printer
LX-300+ II Impact Printer
If the issue persists, let’s disable Easy Printer for a test.
Computer Configuration\Administrative Templates\Windows Components\Terminal Services\Terminal Server\Printer Redirection ->
Disabled
Also test the following KB.
http://support.microsoft.com/kb/959442/en-us
Niki Han
TechNet Community Support

How to do Arial fonts in EPSON LX-300+II

Arial or Helvetica fonts are added in device type EPESCP9 or EPESCP2 in output device that uses EPSON LX 300 + II. I'm using the INCH7 page format for the check printing. When the check was printed, the output was not Arial; instead it looked like a Roman font. Arial fonts are already in list of printer fonts of EPESCP9 and EPESCP2. Also, the font used in check sapscript is already changed to Arial. When I used SWIN, it printed the Arial font correctly. I can't use SWIN since SWIN is for Windows and not for Linux.
Can anybody help me?

Hi,
In SPAD you need to create the Device type & then the page format should be created for that specific Device type.
Best regards,
Prashant

Can't get my epson sx535wd to work. my epson will get contact with my router (sitcom wl306) and my mac is on wifi, but they can't connect. epson can't find the computer and my report says: there are conflicting channels on my router or entry point. help

can't get my epson sx535wd to work. my epson will get contact with my router (sitcom wl306) and my mac is on wifi, but they can't connect. epson can't find the computer and my report says: there are conflicting channels on my router or entry point. please help

OK, let's try these................
1 - Boot up from your install DVD and run "Repair Disk" from the Utility menu. When done, restart back to your desktop, repair permissions and restart your computer. Re-connect your printer.
2 - Download & install the Gimp drivers. Make sure the one you install is compatible w/your OS-Gutenprint 5.2.8-pre1. Repair permissions, restart your computer & re-connect your printer when done.
The Epson model I have, in order to get it to print wirelessly, I had to install a Gimp driver.
3 - Check out the following KB Articles:
Mac OS X 10.4 Help: Connecting to a network printer
Epson Printer Drivers v2.10 OS X
Adding a printer to your printer list in Mac OS X
Mac OS X 10.4 Help: The printer I'm adding says "Driver not installed"
======================
If still unsuccessful after trying all of the above, the problem could be your iBook or human error. You can either call Epson & ask to speak with a Mac savy supervisor or return the printer & find another that is compatible w/your current OS.

Accessing Newport ESP 300 Controller with RS232 Interface

I am trying to access Newport ESP 300 Controller with RS232 interface. My goal is to read Newports collected data with LabView using RS232 Interface. Are there Vi's ore any support available? thank you.

Hi
we have built some routines for this machine
LabVIEW 6.1
are you interested?
greetings from the Netherlands

Epson scanner not work with Mountain Lion?

I have an Epson Expressio 1600Pro scanner with transparency adaptor. It has worked perfectly with previous Macs using OSX 10.4. I have recently bought a MacBook pro and upgraded it to OSX 10.8. I went to Epson's website to get a new driver etc. That tells you it can only be downloaded via Mac Software Update. That was duly done and installed. System prefs lists it under printer and scanners. OK
I have also installed Photoshop Elements 11 and expected to be able to scan direct to there but nothing seems possible. Going to Help says use Image capture or Preview. Yes! there is a small very rudimentary scanning window appears in both apps. Now the problem! Nothing happens. I have tried ALL the various meagre settings on offer, changing size, resolution, custom etc and all that happens is a small rectangle of a scan occurs but no resulting file.
I have been on to Epson who say ONLY image capture will work with 10.8 but as it is a 3rd party software they can offer no assistance. Well image capture does NOT work. I have spent all afternoon trying various things like restarting, unplugging, reconnecting etc etc nothing.
10.8 does seem very buggy. I have even had to stop using Mail and Safari simply because it doesn't work whereas Thunderbird and Firefox work very well.
But I digress, does anyone have any thoughts please?

The following comments are based on installing an Epson RX700 All-in-one printer/copier/scanner so they may not be applicable to you but, for what it's worth here they are. The RX700 scanner worked perfectly with Snow Leopard and then Lion but, when I changed to Mountain Lion, and used the app store to download and install the drivers, I lost the Epson scanner utility (ie. the user interface that gives you all the scanner options).
However, if I used System Preferences and then the Print and Scan option, it brought up a small window where I could select either Print or Scan. Selecting Scan or Open Scanner from this window then opens up a window with all the scanner options in it, including an overview scan. This window has the option to either Hide Details (all the detailed scanner options - resolution, size, output file name etc) or Show them. As far as I can see, this window is actually the Image Capture app, although it doesn't say so.
It might be a long shot but try changing the Auto Selection box in this window to one of the other options (eg. "Detect Separate Items") or setting the "Scan to" to a file.

Using Epson Perfection 1670 scanner with Macbook

Can anyone point me to a work around for using my Epson Perfection 1670 scanner with my new Macbook? Drivers for the Mac OS do not appear to be available at the Epson website. Thanks much!

Thanks again for the help. I contacted Epson support and they directed me to download the same drivers that Apple Support had suggested. For some reason, the new drivers worked, even though I was really just retracing my steps and re-trying a previously attempted solution. The bottom line is, however, that I can scan photos successfully using the MacBook Pro and the Epson Perfection 1670.
Thanks much!

HT4623 How to use epson iprint after connected with iPad help

How to use epson iprint after connected with iPad help.

When you open Epson iPrint, you will see the various options of ways to proceed, e.g., Photos (to print photos), Maintenance (for printer maintenance). Scan (to perform scanning).

Epson LX-300+II with

Similar Messages

Maybe you are looking for