Equipment BOM ( t code - IB01/IB02)
Hi,
I want to check duplicate entry of MAT code in a Equipment BOM ( t code - IB01/IB02) .
is it possible in 4.6B version of SAP R/3.
Plz suggest.
Hi Sunil,
It is not possible in ECC 5.0 also for Equipment BOM.
It is possible only in material BOM creation in PP module.
Regards,
Santhosh
Similar Messages
-
Equipment BOM & Plant assignment
Dear All,
My client having two Maintenance Plant which is 1001 & 1002 & having one planning plant which is 1001.
Here 1001 plant executes the maintenanace of 1001 & 1002 plant.
Actually we have created one Equipment in plant 1002, so its maintenance plant is 1002 & its planning plant is 1001, in this condition when i am going to create Equipment BOM through tcode IB01, then which plant needs to be assigned to that Equipment BOM.....1001 or 1002 ??
Thanks & Regards,
SandeepSandeep,
As equipment has been created in Plant 1002, in equipment BOM creation, plant should be 1002. Equipment BoM definition plant would be based on the equipment location.
Hope this will help you.
Regards,
Maheswaran. -
Error while creating equipment BOM (IB01)
hi guys,
while creating equipment BOM (IB01) i am getting this error, while adding components.
'Material type NLAG cannot be used with item category (plant 1000)'.
regards
chintaHI Chinta,
I understood ur problem IB01-give the equipment number which is generated by the system and give plant name in which you have created the equipment and bom usage as 4 (plant maintenance) and press enter.
Then you will get the components list give the description,quantity and item category as:
as you gave it as L it is throwing an error give it as N(Non stock item), then you wont get the error.while selecting the item cat. you will get differnet components and you select the appropriate one based on you equipment.Hope you issue is resolved.
Regards,
Bharat -
Does anyone know if there is a standar program to load equipment bill of material, i tried using a recording but when executing the batch record the screen changes from the one where i created the recording so is not working. I will appreciate if you can help me out with this. I even tried with a standar object 0030 but is asking me for a logical file that i can not assing.
try with below LSMW IDOC method
Message Type /ISDFPS/BOMEQU BOMs: Equipment BOM
Basic Type /ISDFPS/BOMEQU01 Equipment BOM
Enhancement -
Can someone please specify the steps required to create an equipment bom lsmw
hi Alagasen
why don't you use standard object "create material BOM",change the transaction code from CS01 to IB01
and do the mapping and upload
regards
Seenu -
IB01/IB02 User exits while saving
Hi,
I would like to implement some validations while adding components to the equipment BOM. For this while I save my Equipment BOM using (IB01 /IB02) I would like to add some validatiions.
Can some one help me which BAPI / BADI would be ideal.
Thanks / SandeepHi,
Thanks for your reply. This Badi is working..
I would like to have some validations at component level while save the equipment BOM.
Thanks & br,
Sandeep -
Hi All,
Can anyone please let me know if there is any kind of standard BAPI to upload Equipment BAPI. I use transaction code IB01 to create equipment BOM.
If not, does any guy have a BDC program to upload equipment BOM with transaction code IB01.
Thanks a lot for all your help
BeatleDear,
Pls check FM BAPI_MATERIAL_BOM_GROUP_CREATE or
FM 'CSAI_BOM_CREATE' can be used to create the Equipment BOM, u need to pass STLTY as 'E' in structure STKOB, this will create equipment BOM,.
Regards
Sunil -
Hi All,
Please let me know if there is any BAPI/ FM available for creating Equipment BOM (IB01 trancastion).
Thanks in advance
regards,
BoomaCheck sample code in:
http://scn.sap.com/thread/562325
Regards,
Sergio. -
Tables or Logical database to create standard report for Equipment BOM?
Dear All
My client has requirement for the report with fields like to see the status of Equipment BOM(input of Equipment number in selection screen) or for Particular set of Materials(input of component number in selection screen) available stock quantity,storage location of stock,description of component,price of component,Pending PR of component(if any),Pending PO of component(if any) etc
I want to develop the report with standard infoset query instead of going for abap development.is there any logical database to map the report or what tables can i use for table joins??
Required sample report with fields as below
BOM Component
Stock available/Not available indicator
Description of Components
BOMQty/ UOM
Price
Part Number
Plnt
Sloc
Stock Qty
Bin
Pending PR
Pending PO
1000001121
YES
BEARING
NO
2000
ERS22
1000
MECH
4
A1
300012431
Regards
M.ManojkumarManoj,
The following is the tested solution.
Table join
Output
This figure shows the case of a Equipment BOM where 3 components are there. Installed Quantity are 4, 1, 1 respectively. Last two columns are showing the Storage Locations and the Stocks available.
Fields taken to output are
From STPO : IDNRK MENGE MEINS
From MARD LGORT LABST
As said before, more than this you can not do in SQVI. With this basic join in SQ02, using codes in Extras you can do much more.
Jogeswara Rao K -
Hi,all,
I m maintaining equipment BOM for spare parts planning ,where all item category has been mentioned as "L",now from maintenance order I want to generate Purchase Requisition by changing the item category as "N" after selecting the specfic item from that equipment BOM .But item category field of the maintenance order is coming greyed mode ?how can I change the item category from "L" to "N" to trigger PR??
Also is it possible to create Purchase Requisition from t-code ME51N with reference to an equiment for which I have maintained BOM .Is there any field to enter equipment no from where I can retrieve the spare parts list ?Please give ur valuable suggestion how to proceed.
thanks in advance.
rgds
rajibHi,
BOM item should be maintain with item category u2018Nu2019 or while assigning component to order instead of double clicking on item (BOM item) , Just copy the material (ctrl+c) and assign category :u2018Nu2019 and quantity manually.
In case of second issue: You cannot create a PR with reference to Equipment and there is no field in PR to assign Equipment. If you are having cost centers assigned to equipment in 1:1 ratio, you can assign cost center in account assignment of PR item.
Or else you can go for a standing order that is one standing order is to be assigned to each equipment and same can be used for account assignment for procurement.
In case of capitalization of expense you can go for asset as account assignment.
If you are not looking for account assignment and just want to retrieve the PRs connected to Equipment then you can think of tracking no field.
Raju -
Hi Experts,
I have created a LSMW through "Batch Input Recording" method to upload materials to Equipment BOM.
It caters to upload 5 materials per equipment. However if input data contains only 3 materils for a equipment then LSMW gives an Error. Have to enter 2 more materials to the BOM.
How can i overcome the matter?
Is there any other method that i can follow to upload the Equipment BOM?
Thanks in AdvanceHi,
Use standard Object
0030 Object
0001Method
main Structure : BOMHEADER
Sub Structure : BOM item
BOMHEADER BOM header
EQUNR C(018) Equipment
WERKS C(004) Plant
STLAN C(001) BOM Usage
BOMITEM BOM item
EQUNR C(018) Equipment
POSNR C(004) Item (SD)
POSTP C(001) Item Category
IDNRK C(018) Component
MENGE C(013) Quantity
MEINS C(003) Base Unit of Measure
In Field mapping and conversion rule Maintean TCODE as constant IB01.
Create Logical and Physical path during specify files under Converted Data.
It will create Equipment BOM
Regards,
SandeepV -
BAPI for creation of Equipment BOM
Which BAPI is used for creation of Equipment BOM?
Hi,
Check this Code, it works:
DATA ecsin TYPE csin.
DATA estkob TYPE stkob .
DATA estzub TYPE stzub .
DATA astlnr TYPE stzub-stlnr .
DATA t_stpob TYPE STANDARD TABLE OF stpob WITH HEADER LINE .
PARAMETERS: pa_equnr TYPE equnr DEFAULT '1500037'. "Your Equipment.
START-OF-SELECTION.
ecsin-equnr = pa_equnr.
ecsin-stlty = 'E' .
ecsin-stlan = '4' .
ecsin-werks = 'C002'. "Your Plant.
ecsin-datuv = '20130101'.
estkob-bmein = 'ST'.
estkob-bmeng = 1.
estkob-stktx = 'TEST'.
t_stpob-stlty = 'M' .
t_stpob-postp = 'L' .
t_stpob-idnrk = '000000000040002882'. "Your Component.
t_stpob-meins = 'ST' .
t_stpob-menge = 1 .
t_stpob-rvrel = 'X' .
APPEND t_stpob .
t_stpob-menge = 2.
t_stpob-idnrk = '000000000040002877'. "Your Component.
APPEND t_stpob.
CALL FUNCTION 'CSAI_BOM_CREATE'
EXPORTING
ecsin = ecsin
estkob = estkob
estzub = estzub
* FL_NO_CHANGE_DOC = ' '
* FL_COMMIT_AND_WAIT = ' '
* FL_NO_COMMIT_WORK = ' '
* FL_ALE = ' '
IMPORTING
* FL_WARNING =
astlnr = astlnr
TABLES
t_stpob = t_stpob
EXCEPTIONS
error = 1
OTHERS = 2.
IF astlnr IS INITIAL.
****ERROR.
ENDIF.
IF sy-subrc <> 0.
* MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
* WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
Regards,
Sergio. -
Functional location BOM and Equipment BOM
Hi,
I would like to know which tables store information of Functional location BOM (TCODE 1B11) and Equipment BOM (TCODE IB01). Is there a possibility that once we create these BOM's we can create alternative BOM as in case of Material BOM (TCODE CS01).
Regards,
VishalHi,
Tables for Eq., BOM: EQST, STKO, STPO.
Tables fro Fun., Loc., BOM: TPST, STKO, STPO.
You can use FMs: CS_BOM_EXPL_TPL_V1, CS_BOM_EXPL_EQU_V2 & CS_BOM_EXPL_MAT_V2 for extracting the appropriate BOM related data.
And for the Alternatives please check the customizing or check with your respective Module experts for the appropriate configuration.
Hope this helps.
Best Regards, Murugesh AS -
Equipment BOM quantity field as optional
Hi Expert,
Does anyone know how to set quantity field as optional in Equipment BOM transaction (IB01)
Pls help. Thank you
Rgds,Leni,
The field selection for the quantity field is dependent on the item category,Transaction type, etc of the BOM.The field selection attributes are fixed in tables TCS33. I don't think you can change this through config. However if you are in ECC 6.0 you could consider tweaking the resultant field selection attributes through implicit enhancements on the screen flow logic.
However why would you want an item without quantity?
Regards
Narasimhan -
Equipment BOM and Equipment Task List
Hi
I have created an Equipment BOM (IB01) and Equipment TL (IA01). When creating a WO using IW31 why doesn't the TL and BOM get copied across?
Regards
AdeelWhile doing maintenance for equipment (creating order in IW31), its not necessary that all the operations in task list & all the materials from BoM should be used.
Based on the maintenance, you can select the operations from task list & you can select the components.
In order, go to Extras => Task list selection => Reference object. It will list the task lists available for the equipment, from that you can select.
For components, in components tab, there will be structure button. Click that, it will show you the BoM created, from that list, select required components.
Note: Only in Production order, all the operations from Routing & all components from BoM will be copied. This is because for production order, all the operations & components are required to produce the finished product.
Maybe you are looking for
-
Line Item Display for Gl, Vendor & Customer Accounts
is there any standard report which gives line item details upon running it and not after going through the process of selecting the document listed by the report and then veiwing the line items..?
-
Can't save a PDF data using Reader
I have downloaded a PDF form from a website but I can't save the entered data. Help please
-
I did a fresh install of windows xp on my new lenovo U330. Everything went fine. Yet when I go to install the lastest Ati Mobile Drivers 9.2 it says hardware not found. If I use the Ati drivers from lenovo's site then it works fine, yet the driver is
-
Just recovered my dv5 and it says no serial number found and says product key is not valid
DV5-1045TX Vista 32bit Can anyone help. Keeps asking me to avtivate my new product key or buy one. This is a genuine HP DV5 laptop I have had for 4 years.
-
When I pass a string to a File Browse item from one page to another, and then back, my file browse object is empty, even though the application appears to know its value. In this example, I've shown how I'm debugging my code. http://i37.tinypic.com/1