Equium A60-181 Win XP: incorrect network connection - Taskbar icon notification
Hi everyone,
Ive had my Equium A60-181 for quite a while now and its been quite reliable, its always connected via WiFi to my home network.
Very recently though, the icon in the system tray for network connectivity has been incorrect. It always says I am not connected to the network... but I am, because the internet works and I can still access the network drive which is on another computer on the network, and the network printers.
Why does the system tray tell me that i am not connected to the network when I am?
All help will be greatly appreciated.
And Happy New Year.
Rhys James
Hi
I presume you have assigned the LAN TCP/IP address and the gateway settings manually and these settings are not set to automatic. Am I right?
The same message appeared to me. I have connected my notebook to the other PC and changed the TCP/IP address settings.
This was the reason for this message in the taskbar.
Just simply set it to automatic again and you will get rid of this annoying message.
Best regards
Similar Messages
-
Need battery for Equium A60-181
I am after a new battery for my notepad equium a60-181.
The battery fitted is a PA3384U-1BRS.
I looked on the toshiba web site and could not find this model.
As it been replaced by another model, if so what battery number should i be looking for.Hello my friend. I see you are a new in the forum. Welcome ;)
Now to your question:
You can order all compatible and supported parts from the ASP in your country. I think the guys order it directly from the Toshiba.
Anyway, the Toshiba European site contains a nice site about options and accessories.
There you will find many devices and parts which are listed in the different categories and are compatible with Toshiba notebooks.
Check it -
BIOS update for Equium A60-181
Hi, according to the toshiba website there's a new BIOS update for my laptop.
I was wondering is it worth the update unfortunately there's no information
supplied with regards to bug fixes or improvements ? Also should I use the
Windows update tool or use the bootable CD option it's just I don't feel safe
flashing under Windows XP unless this is a standard flawless procedure ?
cheers,
Richard S.Hi Richard
Richard do you have some problems with your unit? If everything works fine I do not see any reason for BIOS update.
If you think that BIOS update is necessary you can try Windows based Bios Update but please check first Toshiba BIOS-Update Description before proceeding. -
Z1c Losing Network Connection for no Apparent Reason
Hi there, recently I noticed that after longer calls (ca 15+ minutes) my Z1c loses network connection ("No Signal" notification & empty triangle icon instead of signal bars) right after the call has been ended. I tried to turn on and off the airplane mode or to manually select the proper cellular network but these did not bring the signal back. The only thing that helps is restarting the phone (then I get full-strength signal). Just to be clear, I am not referring to a loss of mobile data connection as experienced by some users. What I see is a total loss of mobile network signal. In other words, when this occurs my phone is unreachable (people are not able to call or text me). In the Settings I have "WCDMA (preferred)/GSM". Changing this to "GSM only" is not an option for me because the 2G signal is quite weak and spotty in my area. Using "LTE (preferred)/..." is not an option either due to the lack of LTE coverage. (What can I say -- rural area... :/ ) Additionally, I have enabled the Stamina mode but I doubt this can be the culprit because the problem appeared also when I turned Stamina mode off for a day or so. I should also mention that I use A5.0 Lollipop; however, the problem started appearing only a couple of days ago (I never noticed any such issue with A4.4). Any help would be much appreciated. nvx
I suggest that you try to repair the phone software using PC Companion..
Before repairing your device you may want to backup your information first. Check out this topic for more information on how to.
How to backup?
If the issue should still remain I think that this needs to be examined and fixed at a repair center. For more information about how to submit your phone for repair and where, contact your local support team. -
Windows 8.1 Lock Screen drops network connectivity when screen locked using Win+L
Hi!
I was sent here from Microsoft Community forum. The question is:
Since Windows NT 4.0 I'm using Lock Screen to prevent people from accessing my computer when I'm leaving my room. First I was using CTRL+ALT+DEL / Lock Screen, then switched to Win+L keyboard shortcut when it was first introduced.
Everything was fine until I switched to Windows 8.1 computer (Sony Vaio Duo 13 with Broadcom wireless network controller). This machine is 8.1, not 8.0 upgraded to 8.1.
My problem is that when I hit Win+L combo the Lock Screen (with clock etc.) is displayed. Then, despite I have configured not to turn off display, the screen goes blank (after 30 seconds since lock) and network connectivity is cut off from desktop
apps (I suspect the system goes into Active Standby mode, because Modern UI apps like Tune-In radio keep working fine).
100% repeatable scenarios:
## Scenario 1 ##
1) Log in
2) Open desktop app that uses network connectivity. Outlook 2013 from Office365 subscription
3) Check that it has connected
4) Lock screen (Win+L)
5) Wait for 30 seconds (first incorrectly posted as few minutes) as screen goes black
6) Unlock screen (using password)
7) In right corner of Outlook app you will see "Unable to connect with Exchange server" and few seconds later it will reconnect sucessfuly
## Scenario 2 - the more annoying ##
1) Log in to Win 8.1 computer
2) Connect to it using SMB (in my case I wanted to transfer 30 GB of files from local hard drive C: to server) \\COMPUTER-NAME\c$ from Windows Server 2012 R2
3) Start copying files from computer to server
4) Lock the screen on computer
5) As soon as screen goes black server displays message "Lost connection to the resource. Try again?"
6) Unlock screen on the computer
7) Click "Try again" and it will continue copying files
My power settings are set to go into stand by after 5 hours and if I not lock the screen it doesn't go to sleep before 5 hours.
When I lock the screen using Win+L it goes into (probably Active) Standby mode.
Is there any way to prevent it from going to Active Standby when locking screen? I need the screen lock for security reasons but I don't want it to drop my network connectivity on remote desktops, file transfers and other desktop activities before 5 hour
timeout.
This issue is not related to more or less known wireless network connectivity problem that happens to many Intel Haswell computers. Mine doesn't exhibit those problems. I can easly push 100 - 200 GB of wireless data without network drops.
Computer information:
Sony Vaio Duo 13: SVD1322C5E
Intel Core i5-4200U
8 GB RAM
Windows 8.1 Pro 64-bit
Broadcom 802.11n SDIO network adapter
Originally posted at: http://answers.microsoft.com/en-us/windows/forum/windows8_1-networking/windows-81-lock-screen-drops-network-connectivity/099f16bd-b00d-4ba9-b833-48bf1d55ffe4
Best regards,
SergiuszSame issue here using Surface 3 Pro with either internal WLAN or MS USB LAN Adapter. I'm frequently used to keep open connections over SSH to some servers. On switching to lock screen explicitly by pressing Win+L or implicitly due to idle timeout all
connections to servers are lost. In addition, I don't get any notifications on incoming Skype messages (using Skype for desktop) when lock screen is active.
Neither NIC is showing "Power Management Tab" according to step 5 of instructions above.
Additionally observing USB LAN NIC seems to be kept active after activating lock screen, but traffic stops (according to its flashing light) when lock screen is switching off display. Blanking display doesn't seem to be adjustable in System Settings (Energy
Options accessed through Win+X).
Find attached log file of powercfg -energy -duration 300 ...
Log file is in German. It basically claims unset timeouts for deactivating display while running attached to power supply though lock screen is turning off displays within 1-2 minutes.
Energieeffizienzdiagnose-Bericht
Computername
KRITIAS
Überprüfungszeit
2015-01-10T15:07:47Z
Überprüfungsdauer
353 Sekunden
Systemhersteller
Microsoft Corporation
Systemproduktname
Surface Pro 3
BIOS-Datum
10/16/2014
BIOS-Version
3.11.0350
Betriebssystembuild
9600
Plattformrolle
PlatformRoleSlate
Netzbetrieb
true
Prozessanzahl
67
Threadanzahl
1319
Berichts-GUID
{1a168801-c189-46fe-811c-235e6bf2bd0d}
Analyseergebnisse
Fehler
Energierichtlinie:Verdunkelungszeitlimit ist deaktiviert (Netzbetrieb)
Der Bildschirm ist nicht so konfiguriert, dass er nach einer Zeit der Inaktivität verdunkelt wird.
Energierichtlinie:Standbyzeitlimit ist deaktiviert (Netzbetrieb)
Der Computer ist nicht so konfiguriert, dass nach einer Zeit der Inaktivität automatisch der Wechsel in den Standbymodus erfolgt.
CPU-Auslastung:Prozessorauslastung ist hoch
Die durchschnittliche Prozessorauslastung während der Ablaufverfolgung war sehr hoch. Das System verbraucht weniger Energie, wenn die durchschnittliche Prozessorauslastung sehr niedrig ist. Überprüfen Sie die Prozessorauslastung für einzelne Prozesse,
um festzustellen, welche Anwendungen und Dienste den größten Anteil an der Gesamtprozessorauslastung haben.
Durchschnittliche Auslastung (%)
45.31
Warnungen
Plattform-Zeitgeberauflösung:Plattform-Zeitgeberauflösung
Die standardmäßige Plattform-Zeitgeberauflösung beträgt 15,6 ms (15625000 ns) und sollte immer dann verwendet werden, wenn sich das System im Leerlauf befindet. Wenn die Zeitgeberauflösung erhöht wird, sind die Technologien zur Prozessorenergieverwaltung
möglicherweise nicht wirksam. Die erhöhte Zeitgeberauflösung kann auf eine Multimediawiedergabe oder Grafikanimationen zurückzuführen sein.
Aktuelle Zeitgeberauflösung (100-ns-Einheiten)
10007
Maximale Zeitgeberperiode (100-ns-Einheiten)
156250
Plattform-Zeitgeberauflösung:Ausstehende Zeitgeberanforderung
Von einem Programm oder Dienst wurde eine Zeitgeberauflösung angefordert, die kleiner als die maximale Zeitgeberauflösung der Plattform ist.
Angeforderter Zeitraum
10000
ID des anfordernden Prozesses
3476
Pfad des anfordernden Prozesses
\Device\HarddiskVolume4\Program Files (x86)\Adobe\Adobe Creative Cloud\ACC\Creative Cloud.exe
Energierichtlinie:Bildschirmzeitlimit ist lang (Netzbetrieb)
Der Bildschirm ist so konfiguriert, dass er nach mehr als 10 Minuten Inaktivität ausgeschaltet wird.
Zeitlimit (Sekunden)
900
USB-Standbymodus:Vom USB-Gerät wird nur selten in den Modus für selektives Energiesparen gewechselt.
Von diesem Gerät wurde während der Ablaufverfolgung nur unregelmäßig in den Modus für selektives Energiesparen gewechselt. Die Prozessorenergieverwaltung ist möglicherweise nicht möglich, wenn sich dieses USB-Gerät nicht im Modus für selektives Energiesparen
befindet. Dieses Problem verhindert jedoch nicht den Wechsel des Systems in den Standbymodus.
Gerätename
USB-Verbundgerät
Hostcontroller-ID
PCI\VEN_8086&DEV_9C31
Hostcontrollerspeicherort
PCI bus 0, device 20, function 0
Geräte-ID
USB\VID_05AC&PID_0250
Portpfad
1,2
Standbydauer (%)
14
USB-Standbymodus:Vom USB-Gerät wird nur selten in den Modus für selektives Energiesparen gewechselt.
Von diesem Gerät wurde während der Ablaufverfolgung nur unregelmäßig in den Modus für selektives Energiesparen gewechselt. Die Prozessorenergieverwaltung ist möglicherweise nicht möglich, wenn sich dieses USB-Gerät nicht im Modus für selektives Energiesparen
befindet. Dieses Problem verhindert jedoch nicht den Wechsel des Systems in den Standbymodus.
Gerätename
Surface Ethernet Adapter
Hostcontroller-ID
PCI\VEN_8086&DEV_9C31
Hostcontrollerspeicherort
PCI bus 0, device 20, function 0
Geräte-ID
USB\VID_045E&PID_07AB
Portpfad
1,1
Standbydauer (%)
5
USB-Standbymodus:Vom USB-Gerät wird nur selten in den Modus für selektives Energiesparen gewechselt.
Von diesem Gerät wurde während der Ablaufverfolgung nur unregelmäßig in den Modus für selektives Energiesparen gewechselt. Die Prozessorenergieverwaltung ist möglicherweise nicht möglich, wenn sich dieses USB-Gerät nicht im Modus für selektives Energiesparen
befindet. Dieses Problem verhindert jedoch nicht den Wechsel des Systems in den Standbymodus.
Gerätename
Generischer USB-Hub
Hostcontroller-ID
PCI\VEN_8086&DEV_9C31
Hostcontrollerspeicherort
PCI bus 0, device 20, function 0
Geräte-ID
USB\VID_05AC&PID_1006
Portpfad
1
Standbydauer (%)
5
USB-Standbymodus:Vom USB-Gerät wird nur selten in den Modus für selektives Energiesparen gewechselt.
Von diesem Gerät wurde während der Ablaufverfolgung nur unregelmäßig in den Modus für selektives Energiesparen gewechselt. Die Prozessorenergieverwaltung ist möglicherweise nicht möglich, wenn sich dieses USB-Gerät nicht im Modus für selektives Energiesparen
befindet. Dieses Problem verhindert jedoch nicht den Wechsel des Systems in den Standbymodus.
Gerätename
USB-Eingabegerät
Hostcontroller-ID
PCI\VEN_8086&DEV_9C31
Hostcontrollerspeicherort
PCI bus 0, device 20, function 0
Geräte-ID
USB\VID_045E&PID_0797
Portpfad
1,3
Standbydauer (%)
14
CPU-Auslastung:Einzelner Prozess mit erheblicher Prozessorauslastung
Auf diesen Prozess ist ein erheblicher Anteil der Gesamtprozessorauslastung zurückzuführen, die während der Ablaufverfolgung aufgezeichnet wurde.
Prozessname
firefox.exe
PID
5968
Durchschnittliche Auslastung (%)
1.57
Modul
Durchschnittliche Modulauslastung (%)
\Device\HarddiskVolume4\Program Files (x86)\Mozilla Firefox\xul.dll
0.60
\Device\HarddiskVolume4\Program Files (x86)\Mozilla Firefox\mozjs.dll
0.27
\SystemRoot\system32\ntoskrnl.exe
0.16
CPU-Auslastung:Einzelner Prozess mit erheblicher Prozessorauslastung
Auf diesen Prozess ist ein erheblicher Anteil der Gesamtprozessorauslastung zurückzuführen, die während der Ablaufverfolgung aufgezeichnet wurde.
Prozessname
System
PID
4
Durchschnittliche Auslastung (%)
0.59
Modul
Durchschnittliche Modulauslastung (%)
\SystemRoot\system32\ntoskrnl.exe
0.24
\SystemRoot\system32\DRIVERS\igdkmd64.sys
0.12
\SystemRoot\system32\DRIVERS\avc3.sys
0.07
CPU-Auslastung:Einzelner Prozess mit erheblicher Prozessorauslastung
Auf diesen Prozess ist ein erheblicher Anteil der Gesamtprozessorauslastung zurückzuführen, die während der Ablaufverfolgung aufgezeichnet wurde.
Prozessname
dwm.exe
PID
6264
Durchschnittliche Auslastung (%)
0.47
Modul
Durchschnittliche Modulauslastung (%)
\SystemRoot\system32\ntoskrnl.exe
0.10
\Device\HarddiskVolume4\Windows\System32\dwmcore.dll
0.09
\SystemRoot\System32\drivers\dxgkrnl.sys
0.06
CPU-Auslastung:Einzelner Prozess mit erheblicher Prozessorauslastung
Auf diesen Prozess ist ein erheblicher Anteil der Gesamtprozessorauslastung zurückzuführen, die während der Ablaufverfolgung aufgezeichnet wurde.
Prozessname
Skype.exe
PID
11008
Durchschnittliche Auslastung (%)
0.26
Modul
Durchschnittliche Modulauslastung (%)
\Device\HarddiskVolume4\Program Files (x86)\Skype\Phone\Skype.exe
0.11
\SystemRoot\system32\ntoskrnl.exe
0.05
\SystemRoot\System32\win32k.sys
0.04
CPU-Auslastung:Einzelner Prozess mit erheblicher Prozessorauslastung
Auf diesen Prozess ist ein erheblicher Anteil der Gesamtprozessorauslastung zurückzuführen, die während der Ablaufverfolgung aufgezeichnet wurde.
Prozessname
svchost.exe
PID
1528
Durchschnittliche Auslastung (%)
0.25
Modul
Durchschnittliche Modulauslastung (%)
\SystemRoot\system32\ntoskrnl.exe
0.16
\Device\HarddiskVolume4\Windows\System32\ntdll.dll
0.02
\SystemRoot\system32\drivers\ndis.sys
0.01
Informationen
Plattform-Zeitgeberauflösung:Zeitgeberanforderungsstapel
Der Stapel mit den Modulen, die für die niedrigste Plattform-Zeitgebereinstellung in diesem Prozess verantwortlich sind.
Angeforderter Zeitraum
10000
ID des anfordernden Prozesses
3476
Pfad des anfordernden Prozesses
\Device\HarddiskVolume4\Program Files (x86)\Adobe\Adobe Creative Cloud\ACC\Creative Cloud.exe
Aufrufender Modulstapel
\Device\HarddiskVolume4\Windows\SysWOW64\ntdll.dll
\Device\HarddiskVolume4\Windows\SysWOW64\kernel32.dll
\Device\HarddiskVolume4\Windows\SysWOW64\d3d9.dll
\Device\HarddiskVolume4\Program Files (x86)\Adobe\Adobe Creative Cloud\CEF\libcef.dll
\Device\HarddiskVolume4\Windows\SysWOW64\kernel32.dll
\Device\HarddiskVolume4\Windows\SysWOW64\ntdll.dll
Energierichtlinie:Aktiver Energieplan
Der derzeit verwendete Energieplan.
Planname
Ausbalanciert (OEM)
Plan-GUID
{381b4222-f694-41f0-9685-ff5bb260df2e}
Energierichtlinie:Energieplancharakter (Akkubetrieb)
Der Charakter des aktuellen Energieplans, wenn das System im Akkubetrieb ausgeführt wird.
Charakter
Ausbalanciert
Energierichtlinie:Videoqualität (Akkubetrieb)
Ermöglicht Windows Media Player, bei der Videowiedergabe die Qualität und die Energieeinsparung zu optimieren.
Qualitätsmodus
Videoqualität und Energieeinsparung ausbalancieren
Energierichtlinie:Energieplancharakter (Netzbetrieb)
Der Charakter des aktuellen Energieplans, wenn das System im Netzbetrieb ausgeführt wird.
Charakter
Ausbalanciert
Energierichtlinie:802.11-Energierichtlinie für Drahtlosverbindungen ist "Maximale Leistung" (Netzbetrieb)
Die aktuelle Energierichtlinie für 802.11-kompatible Drahtlosnetzwerkadapter ist nicht für die Verwendung von Energiesparmodi konfiguriert.
Energierichtlinie:Videoqualität (Netzbetrieb)
Ermöglicht Windows Media Player, bei der Videowiedergabe die Qualität und die Energieeinsparung zu optimieren.
Qualitätsmodus
Für hohe Videoqualität optimieren
Systemverfügbarkeitsanforderungen:Erfolgreiche Analyse
Die Analyse war erfolgreich. Es wurden keine Energieeffizienzprobleme festgestellt und keine Informationen zurückgegeben.
Akku:Akkuinformationen
Akku-ID
1F11LGC_LGCX863568
Hersteller
LGC_LGC
Seriennummer
1F11
Chemie
LION
Langfristig
1
Versiegelt
0
Zyklusanzahl
33
Vorgesehene Akkukapazität
42157
Letzte vollständige Aufladung
44209
Funktionen der Plattformenergieverwaltung:Unterstützte Standbystatus
Mithilfe von Standbystatus kann der Computer nach einer Zeit der Inaktivität in einen Energiesparmodus wechseln. Der S3-Standbystatus ist der standardmäßige Standbystatus für Windows-Plattformen. Im S3-Standbystatus verbraucht der Computer nur die Energie,
die notwendig ist, um den Arbeitsspeicherinhalt zu bewahren und die Arbeit mit dem Computer schnell fortsetzen zu können. Sehr wenige Plattformen unterstützen den S1- oder S2-Standbystatus.
S1-Standbymodus unterstützt
false
S2-Standbymodus unterstützt
false
S3-Standbymodus unterstützt
false
S4-Standbymodus unterstützt
true
Funktionen der Plattformenergieverwaltung:Unterstützung von Verbindungsstandby
Mit dem Verbindungsstandby kann der Computer in einen Stromsparmodus wechseln, in dem er immer eingeschaltet und verbunden ist. Der Verbindungsstandby wird soweit unterstützt anstelle der Systemstandbystatus verwendet.
Verbindungsstandby unterstützt
true
Funktionen der Plattformenergieverwaltung:Die adaptive Bildschirmhelligkeit wird unterstützt.
Dieser Computer ermöglicht die automatische Helligkeitsregelung der integrierten Anzeige durch Windows.
Funktionen der Plattformenergieverwaltung:Funktionen zur Prozessorenergieverwaltung
Mithilfe einer effektiven Prozessorenergieverwaltung kann der Computer Leistung und Energieverbrauch automatisch ausbalancieren.
Gruppieren
0
Index
0
Leerlaufstatus - Anzahl
11
Leerlaufstatustyp
Micro-Energiemodul-Plug-In
Nennfrequenz (MHz)
2301
Prozentuale maximale Leistung
100
Prozentuale niedrigste Leistung
32
Prozentuale niedrigste Drosselung
3
Leistungssteuerelementtyp
ACPI-Leistungszustände (P)/ACPI-Drosselungszustände (T)
Funktionen der Plattformenergieverwaltung:Funktionen zur Prozessorenergieverwaltung
Mithilfe einer effektiven Prozessorenergieverwaltung kann der Computer Leistung und Energieverbrauch automatisch ausbalancieren.
Gruppieren
0
Index
1
Leerlaufstatus - Anzahl
11
Leerlaufstatustyp
Micro-Energiemodul-Plug-In
Nennfrequenz (MHz)
2301
Prozentuale maximale Leistung
100
Prozentuale niedrigste Leistung
32
Prozentuale niedrigste Drosselung
3
Leistungssteuerelementtyp
ACPI-Leistungszustände (P)/ACPI-Drosselungszustände (T)
Funktionen der Plattformenergieverwaltung:Funktionen zur Prozessorenergieverwaltung
Mithilfe einer effektiven Prozessorenergieverwaltung kann der Computer Leistung und Energieverbrauch automatisch ausbalancieren.
Gruppieren
0
Index
2
Leerlaufstatus - Anzahl
11
Leerlaufstatustyp
Micro-Energiemodul-Plug-In
Nennfrequenz (MHz)
2301
Prozentuale maximale Leistung
100
Prozentuale niedrigste Leistung
32
Prozentuale niedrigste Drosselung
3
Leistungssteuerelementtyp
ACPI-Leistungszustände (P)/ACPI-Drosselungszustände (T)
Funktionen der Plattformenergieverwaltung:Funktionen zur Prozessorenergieverwaltung
Mithilfe einer effektiven Prozessorenergieverwaltung kann der Computer Leistung und Energieverbrauch automatisch ausbalancieren.
Gruppieren
0
Index
3
Leerlaufstatus - Anzahl
11
Leerlaufstatustyp
Micro-Energiemodul-Plug-In
Nennfrequenz (MHz)
2301
Prozentuale maximale Leistung
100
Prozentuale niedrigste Leistung
32
Prozentuale niedrigste Drosselung
3
Leistungssteuerelementtyp
ACPI-Leistungszustände (P)/ACPI-Drosselungszustände (T)
Gerätetreiber:Erfolgreiche Analyse
Die Analyse war erfolgreich. Es wurden keine Energieeffizienzprobleme festgestellt und keine Informationen zurückgegeben. -
I have an iPod touch and cannot access gmail. I always get username or password for gmail is incorrect. I am able to access gmail via my Windows laptop just fine. I tried deleting and adding a new account, verified that my network connections are working, bebooted my iPod, and verified that imap is enabled on my laptop. Not sure what else to do. Please help!!!
Try going to this link and see if the instructions there help.
https://www.google.com/accounts/DisplayUnlockCaptcha
B-rock -
Equium A60-157 Wireless Network Card/PCMCIA HELP!
Hi, all!
This problem has been frustrating me for at least 2 months.
Ok, I recently purchased a Belkin Wireless G Notebook Card (wifi card).
The first time I installed the wifi card it was working perfectly. I powered
off the laptop (after I had finished working on it). The following day
when I powered on the laptop, you guessed it, the wifi card was not
working. I did not remove the wifi card during the power off/on phase.
When I went into the device manager, a yellow exclamation mark was
above the wifi card. When I examined the wifi cards properties, I found the
following message:
This device cannot find enough free resources that it can use. (Code 12)
If you want to use this device, you will need to disable one of the other devices on this system.
Click Troubleshoot to start the troubleshooter for this device.
I have tried unistalling and reinstalling the wifi card. I have tried using the latest Belkin drivers for the wifi card. Sometimes it works, but when I power off/on the laptop its a no go.
One way I have gotten the card to work was by removing and inserting the card several times
until it found resources and finally worked. I dont use this method anymore as, quite obviously, I risk causing damage to the cardbus slot and the card. In the meantime Ive been using a Belkin Wireless G USB network adaptor. I have not had any problems with the USB adaptor, but I would prefer to use the wifi card. This is because the majority of the wifi card is housed inside the laptop, so its not easily dislodged. The USB adaptor is fine for wireless networking indoors, but too much of a risk for roaming outdoors.
I have had this problem from bios revision 1.70 to 1.8C, and I still have it with revision 1.90. Im planning to take the wifi card back to the shop for an exchange, but I have a very bad feeling that the same thing is going to happen with the replacement card. Im not convinced that the current wifi card is defective, because it works perfectly when it gets resources.
I have tried to manually configure the resources on the devices, but I run into one major problem. Windows seems to be LOCKED into automatic settings. The automatic settings checkbox is completely greyed out, making it impossible for me to clear the check box. I have not seen anything in the bios that can help me resolve this problem.
I have noticed that there are a lot of devices running off IRQ (Interrupt Request) 19, when viewing the resources by type in the device manager. These devices are:
Standard Enhanced PCI to USB Host Controller
Standard OpenHCD USB Host Controller x 2 (two entries)
Texas Instruments OHCI Compliant IEEE 1394 Host Controller
Texas Instrumetns PCI-1410 CardBus Controller
When the wifi card is working it also runs off IRQ 19, but as I stated before Windows is locked into automatic settings and will not let me configure the hardware resources manually.
The Equium A60-157 does not come with onboard, but it has the potential to. Wifi l.e.d. on front panel, location for physical wifi switch on side panel and wifi icon on F8. Does anyone know if Toshiba offer an upgrade service, or can I install onboard wifi myself?
ANYONE, PLEASE HELP ME WITH THESE ISSUES!!!
Thanks for you time!Hi
I found this for you:
Two devices have been assigned the same input/output (I/O) ports, the same interrupt, or the same Direct Memory Access channel (either by the BIOS, the operating system, or a combination of the two). This error message can also appear if the BIOS did not allocate enough resources to the device (for example, if a universal serial bus (USB) controller does not get an interrupt from the BIOS because of a corrupt Multiprocessor System (MPS) table).
You can use Device Manager to determine where the conflict is and disable the conflicting device. On the General Properties tab of the device, click Troubleshoot to start the troubleshooting wizard.
Try to disable the conflict devices. It will be interesting to know if the problem will occur again.
In my opinion you should contact Service partner and ask them if the unit is prepared for Wi-Fi module. Sorry but I am not sure about that and I dont want to give you a wrong information about that. -
Hi all i won't update my iPod touch 4 generation to ios 5 but there are win the download end its showing a massage (the network connection timed out)
Okay. I've tried syncing it first, resetting it first, downloading the firmware, uninstalling and reinstalling iTunes, I've checked my connections and ports and everything, run all kinds of diagnostics, and nothing is working. Every time it says it's backing it up, my iPod resets and then it's back to square one. I'm going to restore it and see if that helps. What a pain in the butt, especially since it wouldn't back it up.... >.<
-
I've been trying for 4 days to download purchased media from iTunes and I keep getting this error message "The network connection timed out." I assure you my internet connection works perfectly.
Not sure if this is relevant, but this error spontaneously happened after my most recent purchase on the night of 2/10. I was able to download some iTunes extras right before I made the most recent HD movie purchase, and as soon as I tried to download that, nada!
Here's what I've already tried, but has NOT worked:
-re-opening iTunes
-restarting computer (several times)
-deleting tmp files
-disabling antivirus ware & firewalls
-deleting & re-installing iTunes
If anyone has any other ideas to help me out, I'm all ears!
Thanks!
Ehi, thanks for your response!
please excuse my ignorance, but do you mean log into my iTunes at an apple store & download my purchases onto a flash? I wasn't aware I could do that... -
Blackberry Desktop Software slows down Network Connectivity on Win 7 start up
Hi,
I am new so be gently..lol
I am running windows 7 64bit Home Premium. I recently noticed that on start up my PC was taking between 10 and 20 seconds to set up it's network connectivity, which previously was almost instant. There were no erros within the event logs to suggest why this was occuring. The last thing installed was the blackberry desktop manager. I uninstalled this, and found that my network connectivity was now occuring almost instantly again.
Is this a know issue with this software? I have searched the forum but cannot find anything simliar, only people saying it was slowing down start up as a whole which is not what is happening to me.
Thanks for any help or advice in advance.
TLEHi and Welcome to the Forums!
Typically, if you have installed the RIM DTM software to auto-start every time you boot your PC, the boot time will increase. Personally, I've found no reason to allow DTM to auto-start...I only launch it when I need it.
To perform a full clean uninstall, see this KB:
KB02206 How to perform a clean uninstall of BlackBerry Desktop Software
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
Equium A60 doesn't work properly with Logitech Quickcam Fusion
Has anyone managed to use a Logitech Quickcam Fusion webcam with an Equium A60 ?
I've installed the latest available drivers and software and most times it just screws up the operation of the PC. It eventually hangs so badly that I can't even recover using Windows Task Manager!! If I leave the USB lead connected to the PC, 9 times out of ten, it won't boot up into Windows, until I remove the lead :(
I've installed the same software and drivers on my Desktop PC and the camera works fine every time and boots OK with the camera connected to a USB port.
Both PCs are using Win XP with SP2 and all released updates.Hello Bill
Do you have problems with USB ports if you use other devices? I really don?t know what the problem can be. Check Logitech SUPPORT PAGE
Maybe you will find some advice there. -
Equium A60-191: Modem issue - Only analog phone lines are supported
My Equium A60 was powered up when lightning struck nearby and caused the electricity supply to go off and back on.
The OS is XP Home and my ISP is AOL. When I try to access the Net by DUN, I receive the repeated error message:
"Connected phone line is not compatible with this modem. Only analog phone lines are supported."
My desktop computer, which also uses AOL, still connects to the same phone line without any problem.
I have rebooted the A60 several times; changed and tried out 2 phone connnection cables - both work; the phone line works fine; I have reinstalled the driver provided on this site; removed the tick from the box that says to wait for the dial phone; checked out that the modem is in working and on the Device Manager list. All of this is to no avail.
Troubleshooter is suggesting that COM 3 is not enabled. I cannot see COM 3 listed in Device Manager, under Ports.
I have tried Google and ASK with the error message. There are not many posts and it appears that the Toshiba modem is in fact an Agere. This makes seems to be the subject of some of the complaints.
Finally I have uninstalled the driver/modem, AOL and one other DUN connection. I rebooted and went through the process of installing "New Hardware" and AOL. Whilst the modem is enabled and allegedly working... I am still unable to connect to the Net. I reinstalled an additional 'pay as you go' ISP. When I try to dial out on that it generates the error 680. It does this even when the box is unchecked, for wait for a dial tone.
I would be most grateful if anybody could help. I have run out of ideas.
Many thanks.Hi
You are right, the modem support the Agere Modem Chip.
You will not find the COM3 in the device manager because the modem uses not real com port. Its a virtual com port.
I think you should start the diagnostic tool test and check if the Modem has no malfunction.
Additional you should delete the connection in the Region Select Utility and after new reboot create a new one.
I found also the useful Microsoft article about the Troubleshooting network and dial-up connections.
http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/trouble_all.mspx?mfr=true
and here you will find info about the DUNS error 680:
http://www.modemsite.com/56k/duns680.asp
http://php.iupui.edu/~aamjohns/trouble.html#No Dial Tone -
Losing network connection and NIC acts weird from warm/hot weather/temperatures?
Hello.
Is there a known issue on MSI P43 NEO3-F (MSI-7514) motherboards' onboard RealTek RTL8168C (P)/8111C(P) PCI-E Gigabit Ethernet NIC network disconnecting and acting weird during warm/hot weather?
I noticed lately and back on 1/11/2009 night when weather got warm/hot (e.g., my room can get over 85F degrees, but lately it has been 80F degrees), my network would lose its connection. See http://img9.imageshack.us/img9/5580/screenshots.gif for a few SpeedFan's sensor readings when the incidents occurred. I have never seen this happen when the weather is cooler (60-70F degrees in my room).
I also think this only happens if I am using the PC lightly (nothing intensive) like watching fullscreen videos (video overlay), surfing the Web, etc. I don't see any errors or evidences that it happens when idled (e.g., asleep or out). Uptime doesn't seem to matter since I have seen days to 3.5 hours.
I tried upgrading network driver twice (e.g., Realtek_XP_5714_0219 from
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=13&PFid=5&Level=5&Conn=4&DownTypeID=3&GetDown=false ...), disabling Kerio Personal Firewall v2.1.5 (XP's disabled already), releasing and renewing IP address (works, but still no network -- can't even ping my router!), unplugging and replugging the cat5 cable (do see the network port lights on), touching the network jack and hardware inside and outside of the case (not hot), trying another cat5 cable and a network port on a switch instead router's), changing from "Minimal Power Management" to full power (no underclocking/slowing down when idled), etc.
During the disconnections, I tried:
C:\>tracert 192.168.0.1
Tracing route to 192.168.0.1 over a maximum of 30 hops
1 * * * Request timed out.
2 * * * Request timed out.
3 * * ^C
IPCONFIG.EXE /ALL when having network problems:
Windows IP Configuration
Host Name . . . . . . . . . . . . : FOOBAR
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter VMware Network Adapter VMnet8:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet8
Physical Address. . . . . . . . . : 00-50-56-C0-00-08
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.134.1
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
Ethernet adapter VMware Network Adapter VMnet1:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet1
Physical Address. . . . . . . . . : 00-50-56-C0-00-01
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.80.1
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
Ethernet adapter HDTV Tuner 2:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : TechniSat DVB-PC TV Star PCI #3
Physical Address. . . . . . . . . : 00-D0-D7-30-19-C1
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 169.254.178.3
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
DHCP Server . . . . . . . . . . . : 169.254.178.1
Lease Obtained. . . . . . . . . . : Saturday, February 28, 2009 6:55:04 PM
Lease Expires . . . . . . . . . . : Monday, July 13, 2009 11:28:08 PM
Ethernet adapter HDTV Tuner 1:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : TechniSat DVB-PC TV Star PCI
Physical Address. . . . . . . . . : 00-D0-D7-30-1A-1D
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 169.254.178.4
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
DHCP Server . . . . . . . . . . . : 169.254.178.1
Lease Obtained. . . . . . . . . . : Saturday, February 28, 2009 6:55:21 PM
Lease Expires . . . . . . . . . . : Monday, July 13, 2009 11:28:25 PM
Ethernet adapter Local Area Connection 15:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC
Physical Address. . . . . . . . . : 00-21-85-1A-C6-72
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.0.82
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.0.1
DNS Servers . . . . . . . . . . . : 192.168.0.1
4.2.2.1
I checked Windows XP Pro. SP3's event logs and noticed these during the disconnections:
Event logs showed:
Event Type: Information
Event Source: Tcpip
Event Category: None
Event ID: 4201
Date: 2/28/2009
Time: 6:42:23 PM
User: N/A
Computer: FOOBAR
Description:
The system detected that network adapter \DEVICE\TCPIP_{51FDDE0F-0935-416E-8FE0-3E1A50847D41} was connected to the network, and has initiated normal operation over the network adapter.
For more information, see Help and Support Center at
http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 00 00 00 00 02 00 50 00 ......P.
0008: 00 00 00 00 69 10 00 40 ....i..@
0010: 02 00 00 00 00 00 00 00 ........
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........
Event Type: Information
Event Source: BROWSER
Event Category: None
Event ID: 8033
Date: 2/28/2009
Time: 6:47:22 PM
User: N/A
Computer: FOOBAR
Description:
The browser has forced an election on network \Device\NetBT_Tcpip_{89F40100-0D8D-4C33-A32D-3D91CAEB3FBD} because a master browser was stopped.
For more information, see Help and Support Center at
http://go.microsoft.com/fwlink/events.asp.
Event Type: Information
Event Source: Tcpip
Event Category: None
Event ID: 4201
Date: 3/1/2009
Time: 6:19:08 AM
User: N/A
Computer: FOOBAR
Description:
The system detected that network adapter \DEVICE\TCPIP_{51FDDE0F-0935-416E-8FE0-3E1A50847D41} was connected to the network, and has initiated normal operation over the network adapter.
For more information, see Help and Support Center at
http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 00 00 00 00 02 00 50 00 ......P.
0008: 00 00 00 00 69 10 00 40 ....i..@
0010: 02 00 00 00 00 00 00 00 ........
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........
Event Type: Information
Event Source: Tcpip
Event Category: None
Event ID: 4201
Date: 3/1/2009
Time: 6:19:20 AM
User: N/A
Computer: FOOBAR
Description:
The system detected that network adapter \DEVICE\TCPIP_{51FDDE0F-0935-416E-8FE0-3E1A50847D41} was connected to the network, and has initiated normal operation over the network adapter.
For more information, see Help and Support Center at
http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 00 00 00 00 02 00 50 00 ......P.
0008: 00 00 00 00 69 10 00 40 ....i..@
0010: 02 00 00 00 00 00 00 00 ........
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........
I also noticed the disconnections usually start with red X icon in my taskbar with its bubble and then later the long disconnection even though no red X (1 GB and connected). If I were to disconnect the cat5 cable from NIC, then it wouldn't even detect it is missing the cable!
The only way to fix this was to reboot (best way and last longer) OR disable network connection and re-enable it (Windows XP's Network Connections) or the NIC itself (Device Manager), but that doesn't always last long (maybe a minute). Example of my pings right after disabling and re-enabling NIC:
C:\>ping 192.168.0.1 -t
Pinging 192.168.0.1 with 32 bytes of data:
Request timed out.
Reply from 192.168.0.1: bytes=32 time<1ms TTL=150
Reply from 192.168.0.1: bytes=32 time<1ms TTL=150
Reply from 192.168.0.1: bytes=32 time<1ms TTL=150
Request timed out.
Reply from 192.168.0.1: bytes=32 time<1ms TTL=150
Request timed out.
Request timed out.
Reply from 192.168.0.1: bytes=32 time<1ms TTL=150
MSINFO32 in case it helps (seems OK to me, but I am not a hardware expert):
[Conflicts/Sharing]
Resource Device
I/O Port 0x00000000-0x00000CF7 PCI bus
I/O Port 0x00000000-0x00000CF7 Direct memory access controller
I/O Port 0x000003C0-0x000003DF Intel(R) 4 Series Chipset PCI Express Root Port - 2E21
I/O Port 0x000003C0-0x000003DF ATI Radeon HD 4800 Series
IRQ 21 Intel(R) ICH10 Family USB Universal Host Controller - 3A38
IRQ 21 OHCI Compliant IEEE 1394 Host Controller
IRQ 21 TechniSat DVB-PC TV Star PCI
IRQ 23 Intel(R) ICH10 Family USB Universal Host Controller - 3A34
IRQ 23 Intel(R) ICH10 Family USB Enhanced Host Controller - 3A3A
I/O Port 0x0000B000-0x0000BFFF Intel(R) 4 Series Chipset PCI Express Root Port - 2E21
I/O Port 0x0000B000-0x0000BFFF ATI Radeon HD 4800 Series
IRQ 16 Intel(R) 4 Series Chipset PCI Express Root Port - 2E21
IRQ 16 ATI Radeon HD 4800 Series
IRQ 16 Intel(R) ICH10 Family USB Universal Host Controller - 3A37
IRQ 16 Standard Dual Channel PCI IDE Controller
IRQ 16 Intel(R) ICH10 Family PCI Express Root Port 2 - 3A42
IRQ 16 Intel(R) ICH10 Family PCI Express Root Port 6 - 3A4A
IRQ 16 ASUS TV880 Video Capture (NTSC)
IRQ 17 Microsoft UAA Bus Driver for High Definition Audio
IRQ 17 Intel(R) ICH10 Family PCI Express Root Port 1 - 3A40
IRQ 17 Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC
Memory Address 0xD0000000-0xDFFFFFFF Intel(R) 4 Series Chipset PCI Express Root Port -
2E21
Memory Address 0xD0000000-0xDFFFFFFF ATI Radeon HD 4800 Series
IRQ 18 Intel(R) ICH10 Family USB Enhanced Host Controller - 3A3C
IRQ 18 Intel(R) ICH10 Family USB Universal Host Controller - 3A36
IRQ 19 Intel(R) ICH10 Family USB Universal Host Controller - 3A39
IRQ 19 Intel(R) ICH10 Family USB Universal Host Controller - 3A35
IRQ 19 Intel(R) ICH10 Family 4 port Serial ATA Storage Controller 1 - 3A20
IRQ 19 Intel(R) ICH10 Family 2 port Serial ATA Storage Controller 2 - 3A26
Memory Address 0xA0000-0xBFFFF PCI bus
Memory Address 0xA0000-0xBFFFF Intel(R) 4 Series Chipset PCI Express Root Port - 2E21
Memory Address 0xA0000-0xBFFFF ATI Radeon HD 4800 Series
Memory Address 0xFED90000-0xFED93FFF System board
Memory Address 0xFED90000-0xFED93FFF System board
I/O Port 0x000003B0-0x000003BB Intel(R) 4 Series Chipset PCI Express Root Port - 2E21
I/O Port 0x000003B0-0x000003BB ATI Radeon HD 4800 Series
[IRQs]
Resource Device Status
IRQ 9 Microsoft ACPI-Compliant System OK
IRQ 16 Intel(R) 4 Series Chipset PCI Express Root Port - 2E21 OK
IRQ 16 ATI Radeon HD 4800 Series OK
IRQ 16 Intel(R) ICH10 Family USB Universal Host Controller - 3A37 OK
IRQ 16 Standard Dual Channel PCI IDE Controller OK
IRQ 16 Intel(R) ICH10 Family PCI Express Root Port 2 - 3A42 OK
IRQ 16 Intel(R) ICH10 Family PCI Express Root Port 6 - 3A4A OK
IRQ 16 ASUS TV880 Video Capture (NTSC) OK
IRQ 17 Microsoft UAA Bus Driver for High Definition Audio OK
IRQ 17 Intel(R) ICH10 Family PCI Express Root Port 1 - 3A40 OK
IRQ 17 Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC OK
IRQ 21 Intel(R) ICH10 Family USB Universal Host Controller - 3A38 OK
IRQ 21 OHCI Compliant IEEE 1394 Host Controller OK
IRQ 21 TechniSat DVB-PC TV Star PCI OK
IRQ 19 Intel(R) ICH10 Family USB Universal Host Controller - 3A39 OK
IRQ 19 Intel(R) ICH10 Family USB Universal Host Controller - 3A35 OK
IRQ 19 Intel(R) ICH10 Family 4 port Serial ATA Storage Controller 1 - 3A20 OK
IRQ 19 Intel(R) ICH10 Family 2 port Serial ATA Storage Controller 2 - 3A26 OK
IRQ 18 Intel(R) ICH10 Family USB Enhanced Host Controller - 3A3C OK
IRQ 18 Intel(R) ICH10 Family USB Universal Host Controller - 3A36 OK
IRQ 23 Intel(R) ICH10 Family USB Universal Host Controller - 3A34 OK
IRQ 23 Intel(R) ICH10 Family USB Enhanced Host Controller - 3A3A OK
IRQ 20 Creative SB Audigy 2 ZS (WDM) OK
IRQ 22 TechniSat DVB-PC TV Star PCI #3 OK
IRQ 0 System timer OK
IRQ 8 System CMOS/real time clock OK
IRQ 13 Numeric data processor OK
IRQ 4 Communications Port (COM1) OK
IRQ 6 Standard floppy disk controller OK
IRQ 1 Standard 101/102-Key or Microsoft Natural PS/2 Keyboard OK
IRQ 12 Microsoft PS/2 Mouse OK
IRQ 14 Intel(R) ICH10 Family SMBus Controller - 3A30 OK
My detailed computer configurations can be found here: http://alpha.zimage.com/~ant/antfarm/about/computers.txt (primary computer).
Thank you in advance.Quote from: NovJoe on 02-March-09, 23:10:05
Force your NIC to run at 100Mbps full duplex and see how it goes.
Check your router / switch ports as well as cables.
I will try 100 Mbps if it happens again. So far, it hasn't occurred after installing the driver supplied by MSI's Web site and not RealTek's Web site. The room temperatures even got warmer like 83F degrees.
As for router and switch, what am I checking for? Other computers didn't have any problems. As for cat5 cables, I already tried another one like I said in my original post. -
i went to the itunes store to download a tv show and music and when i tried it said we could not complete your request the network connection could not be established. please try again later.then it says unknown error occured-50
Close your iTunes,
Go to command Prompt -
(Win 7/Vista) - START/ALL PROGRAMS/ACCESSORIES, right mouse click "Command Prompt", choose "Run as Administrator".
(Win XP SP2 & above) - START/ALL PROGRAMS/ACCESSORIES/Command Prompt
In the "Command Prompt" screen, type in
netsh winsock reset
Hit "ENTER" key
Restart your computer.
If you do get a prompt after restart windows to remap LSP, just click NO.
Now launch your iTunes and see if it is working now.
If you are still having these type of problems after trying the winsock reset, refer to this article to identify which software in your system is inserting LSP:
iTunes 10.5 for Windows: May see performance issues and blank iTunes Store
http://support.apple.com/kb/TS4123?viewlocale=en_US -
I can't access iTunes Store? network connection could not be established.
I recently updated itunes to the latest, but now I can't get the itunes store to work, it just comes up with the message "we could not complete you itunes store request. the network connection could not be established... there was an error in the itunes store. please try again later"
Close your iTunes,
Go to command Prompt -
(Win 7/Vista) - START/ALL PROGRAMS/ACCESSORIES, right mouse click "Command Prompt", choose "Run as Administrator".
(Win XP SP2 & above) - START/ALL PROGRAMS/ACCESSORIES/Command Prompt
In the "Command Prompt" screen, type in
netsh winsock reset
Hit "ENTER" key
Restart your computer.
If you do get a prompt after restart windows to remap LSP, just click NO.
Now launch your iTunes and see if it is working now.
If you are still having these type of problems after trying the winsock reset, refer to this article to identify which software in your system is inserting LSP:
iTunes 10.5 for Windows: May see performance issues and blank iTunes Store
http://support.apple.com/kb/TS4123?viewlocale=en_US
Maybe you are looking for
-
Scratching sounds coming from hard disk.
For the past few weeks there has been a scracthing sound which is generally getting worse that sounds like its coming from the hard disk. It is under warranty in south east asia but I am currently studying in the UK and its not possible to take it ba
-
I've been sent some word documents via email and I can't open them. My computer says that Word 2010 is not installed on my computer. It is. It came with my computer. This makes no sense. Can anyone offer an explanation?
-
Sending attachments to Eudora users using Apple MAIL
I have recently changed from Entourage to MAIL in Tiger and it seems to work well, however I can't seem to send attachments to anyone using Eudora. They recieve the email but the attachment is missing (apparently the recipient company's server is sto
-
ScrollRectToVisible don�t work after jpanel.add(component)
Hi, sorry if this question is allready solved but I coundn�t find a hind. I have a JPanel that is attached to an scrollPane. I add several JPanels depending on what data the user selects to this JPanel. Without intervention the Panel is then scrolled
-
Hi, I want to use jardiff. I have downloaded JnlpDownloadServlet and trying to implement it. I read complete documentation, but sill I',m not clear about the 2 approaches. Plz correct me If I'm wrong. 1) I have to change .jar file name, considering B