Erase old error messages of MacPro RAID Card?

Hi there.
I changed HDDs in my MacPro, they were configured as an RAID 1 using Apples RAID Card.
After mirroring the old System to the new (RAID 5) System, there are several error messages left in RAID Utility - where are they located to delete them?
Maybe I was wrong simply to change the HDDs, but is there a chance to solve that issue?
Thanks in advance.

Get someone on ebay to buy your over priced under supported card.
Or accept the 2.2TB (some people only got the 800GB portion which needs to be set as free space).
Or use 2TB drives.
Or external RAID but watch out for ATTO SAS and their Java program that doesn't work.
WD RED 3TB drives are designed for NAS RAID, firmware to support RAID TLER.
SoftRAID 4 makes a nice software RAID and does a good mirror with three drives in stripe reads (mirror only begins with minimum of two).
NO Apple just won't can't whatever offer a card and firmware. Odd with all their GUID support for large volumes isn't it.
It is designed for smaller SAS drives in today's world. And for RAID5 on 3TB and issues with battery... POS throw it up on ebay!

Similar Messages

MacPro Raid Card single drive size limit

OK this is a follow up to a previous question about the upper size limit of a single HD that the Macpro Raid card can address.
It was pointed out to me that "The Apple RAID card cannot address more than 2.2TB of a drive" by Mr. Grant Bennet-Alder. So I am assuming that a 2TB SAS will work.
I plan to RMA the 4TB drive (that was not recognised), so my question is will this drive work instead?
Seagate Constellation ES 2TB 6GB/S SAS 7200RPM 3.5in (ST2000NM0001) Hard Drive - setup as JBOD.
It's not that I don't believe what Grant has said, it's just that I don't want to RMA this drive as well, using the old wood working philosophy of 'measure twice, cut once.'
And I spent 2 hr looking for this info on Apple's support site without any luck.
SYS INFO
MacPro 5,1
2 X 6 Core 2.93 GHz Xeon
Mac Pro RAID Card
Bay 1: 450GB Seagate Cheetah SAS -JBOD
Bay 2: 450GB Seagate Cheetah SAS - Raid set 1
Bay 3: 450GB Seagate Cheetah SAS - Raid set 1
Bay 4: 2TB Seagate Constellation (potential drive) to be JBOD
Raid set 1: Raid 0 - 900GB
OWC Mercury Accelsior 240GB
ATI Radeon HD 5870
Mac OS X 10.6.8
All software updates current and applied
Thanks
-Robert
Previous thread:
https://discussions.apple.com/message/21675625#21675625

If a Disk Fails If a RAID set or volume becomes degraded because a disk has failed, you can use RAID Utility to identify the disk that needs to be replaced.
Note: If your RAID setup includes a spare drive, it is automatically incorporated into the RAID set, and the set switches from degraded to good as soon as the recovery process finishes. If there is no spare, the set will remain degraded until you replace the failed drive, and if a second drive fails before you replace the first, you could lose data.
To replace a failed disk:
1 Open RAID Utility, select the RAID set or volume that is displaying a problem status indicator, and look for a drive bay with a red status indicator. The bay numbers in RAID Utility correspond to the numbered drive bays in your Mac Pro or Xserve.
2 Replace the bad drive module.
3 Use the Make Spare command to set up the new drive as a global spare. If no spare was available when the original drive failed, the RAID card uses the new spare immediately to rebuild the affected RAID set and volumes. If a spare was available at the time of the failure, it is already incorporated into the affected RAID set, and the new spare remains available until it is needed.
https://manuals.info.apple.com/MANUALS/0/MA318/en_US/RAID_Utility_User_Guide.pdf

HT4137 Will doing this erase old text messages? If so, is there any way to avoid losing them?

I just looked read iOS: How to back up your data and set up as a new device. I've been having a few bugs, but do not want to lose my old text messages. Will setting up as a new device and then syncing erase old text messages? If so, is there any way to avoid losing them?

You will not lose text message, if you back up your phone correctly and then restore from that backup. If your going to restore your phone as new and not from backup, then your text will not be there until you decide to restore from that backup.
If you don't want to lose the message, take a look in the app store to see if you can transfer to your computer.

Great Problemes after installing Yosemite (10.10.2 ) with Photoshop CS6....The program crashes --last time 10 times during my work session..wacomtable doesnt work..it is slow...and get error messages about the graphic card....It s a Terror to work with my

great Problemes after installing Yosemite (10.10.2 ) with Photoshop CS6....The program crashes --last time 10 times during my work session..wacomtable doesnt work..it is slow...and get error messages about the graphic card....It s a Terror to work with my beloved Photoshop!

The Yosemite upgrade very often damages existing Photoshop installations. Thank Apple for that.
You need to uninstall and re-install Photoshop, then apply all the Photoshop upgrades from scratch.
But first, give us details about your setup:
BOILERPLATE TEXT:
Note that this is boilerplate text.
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
A screen shot of your settings or of the image could be very helpful too,
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

The error message "no air port card installed" keeps coming up

I have a mac book pro from 2010... recently set the computer up to act as more of a desktop by adding a monitor etc. I went to use the internet but the computer error message popped up saying "no air port card installed" I tried a few things that were listed but nothing seemed to reset this. I bought a wireless usb adapter but it was only compatable with a microsoft windows which I do not have. I dont want to take it to get a new airport card installed as it is an old computer and the screen is partially broken, but i would like to know if there is a wireless usb adapter that would be compatible or even if the air port express would work in spite of the error message that I have been getting. would love some thoughts or ideas. thanks!

First before getting another wireless USB adapter, try the following:
1a. Delete Preferred Network(s)
System Preferences > Network > Wi-Fi > Advanced > Wi-Fi tab
Under "Preferred Networks," delete the network(s) you regularly use from the list.
1b. Delete AirPort Keychain Entries
Launch the "Keychain Access" application located in Applications/Utilties.
In the windows on the left side: Select login for Keychains and "All Items" for Category.
Click on the "Kind" filter at the top, and look for any "AirPort network password" entries...and delete them.
1c. Add Preferred Network(s)
System Preferences > Network > Wi-Fi > Advanced > Wi-Fi tab
Add the preferred network(s) using the "+" button.
Restart or log out then back in.
2. Move System Configuration Files
(Note: You will have to reestablish your network connections settings.)
Go to /Library/Preferences
Move the SystemConfiguration folder to the desktop.
Restart your Mac. (Note: OS X will rebuild the files that are now sitting on your desktop. If this doesn't resolve the issue, you can move the folder back to it's original location.)
Please post back your results.

Macpro raid card(Battery is Missing)

MacPro 2010
I bought a raid card a month ago.
But I got a message "But Battery is missing".
My Raid Card is Corrupt?
Could you teach me the reason?

google translate says:
My macpro 2010 have the same problem, replace the battery to repair the same problem after the new battery Month 3 Months generated.

Error message: /Users/ MACPRO/Library/Preferences/Adobe/After Effects/10.5/Adobe After Effects 10.5-x64 Prefs (3::3)

I just got an old new Mac Pro & transferred my Applications. When I run After Effects 5.5 and try to save I get the above error message. HELP!!

I have the exact same problem as rumtone had. The only difference is that once I uninstalled After Effects CS5.5 and reinstalled it, and checked the user permissions on the Library folder it still gave me the same error message. The error message only occurs when I try to save or when I try to open save files. Is there anything else i can do?

'No Computer Connection' error message when saving memory card pics

The printer is an HP Photosmart Premium C309g-m connected as a network device to an infrastructure communication mode wireless network.
There are no problems printing documents.
Documents have also been scanned and sent to specific computers on the network in the past.
So it certainly seems that there is a computer connection.
When a memory card holding pictures is inserted into the wireless printer and one tries to save the memory card pictures from the printer to a network computer without a memory card slot, one gets the error message, 'There is no computer connection'.
The Wireless Network Test Report Diagnostic Summary is all PASS with Very Good signal strength.
The Diagnostic Utilities were useless to me. I can only guess at what the problem might be because it isn't specifically mentioned as a possibility.
I tried turning the firewall off but it made no difference.
The documentation mentions UDP Port 427 but doesn't state the protocol to be entered into the slot for Windows Firewall.
There is a list of exception files but no detailed information on how to add them as exceptions into Windows Firewall.

Try this basic troubleshooting fix:
1 - delete the IDVD preference file, com.apple.iDVD.plist, that resides in your
User/Home/Library/ Preferences folder.
2 - delete IDVD'S cache file, Cache.db, that is located in your
User/Home/Library/Caches/com.apple.iDVD folder.
3 - launch IDVD and try again.
NOTE: In Lion and Mountain Lion the Home/Library folder is now invisible. To make it permanently visible enter the following in the Terminal application window: chflags nohidden ~/Library and hit the Enter button - 10.7: Un-hide the User Library folder.
OT

MacPro Raid Card w/ SAS Drives is battery required?

We have a MacPro (early 2008) dual 2.8 Quad with Mac Raid Card and 4 300g SAS drives. The battery became an issue early on it was always showing low on start-ups. Now it shows failed. I am now running system with 3 drives striped raid 0. Is the battery required to be replaced? I like this system for the speed it gives us on short HD, using my original media as the back-up. I am a little out of my league with the SAS drives so any opperation tips would be a plus! Thanx in advance....

The RAID card allows for the use of SAS drives or for the use of RAID 5 (which requires checksum calculation on writes and for data re-creation after a failure).
The battery assures that the data will be held in the RAID card's RAM until it can be written to the drives, even if a power failure occurs just after the data are written to the card (but before they are re-written to the drives).
Not using that feature? You don't need the battery.
Not using RAID 5 or SAS drives? You don't need the Apple RAID card. Disk Utility can set up Striped or Mirrored RAID sets.

Error message indicating that iTunes card has not been properly activated. Please help.

I tried to redeem an iTunes card but an error message pops up indicating that it has not been properly activated.
What should I do?
Please help.
Thanks in advance

What you normally should do when you have an iTunes card that has not been activated is go back the retailer from whom you purchased the card and discuss the problem with them. They should either correctly activate the card or give you a new one. If they refuse to help, as some retailers do, or you don't know or can't get to the retailer, go here:
iTunes Support
and follow the instructions to report the issue to the iTunes Store. They will ask for a scan of the front and back sides of the card as well as a scan of the receipt
Regards.

Just got this error message - The installed graphics card does not meet the minimum requirements for Aperture

Help. I have an iMAC - not even one year old - just got this message - The installed graphics card does not meet the minimum requirements for Aperture.
I have not made any changes to my machine. Help - I can't get to my images

Try restarting your system.
If that does not help, we will need to know your Aperture version and MacOS X version. And do you use an external monitor? Then disconnect it before rebooting.

IPhoto: Error message when creating/buying card

How do I figure out which photo in an iPhoto card layout has a "null file name"? Error message says that I cannot purchase card due to a photo having a null filename.

Does the error occur when you preview?
Before ordering your book (or other project) preview it using this method - http://support.apple.com/kb/HT1040 - and save the resulting PDF for reference - the delivered project will match it.
If it does then remove them one by one and preview until you find the ofending photos
LN

Same old error message - 0x80020022

I am trying to find an answer to how I can burn DVD's on my Power Mac G5.
I have tried to follow the threads posted in the past, but they just go on for pages and apages and pages ( literally )
of one after another person chiming in that they have the problem, and isn't it time Apple address it - and no one
offering a solution.
Someone did suggest running a " repair disc permissions " , but when I open it - the CD/DVD drive is grayed out si
I can't even do that.
It will read in CD's and such, but I cannot burn to a DVD.
Someone else suggested different media - DVD+R as opposed to DVD-R, which I don't happen to have on hand or
I would try that.
I would replace the drive but am unfamiliar with Macs generally and don't want to go through the ardor of their special
case and special screws and specioal connectors ( all to replace a special drieve that unbelievably doesn't want to work )
Is there an answer to this problem that seems so prevalent ??
Thank you for any help,
Sterne

Hi
You must describe more - What You did do - to get this Error Message
• Material used as Video-Codec, Audio and Phjoto file format, frames per sec
• Video editor used
• How exported to iDVD
• DVD type of project - 4x3 or wide - PAL or NTSC
• Brand of DVD used
• Burn Speed - set or as on DVD
and much much more
My General Trouble shooting guide
When iMovie/iDVD doesn't work as intended this can be due to a lot of reasons
• iMovie Pref files got corrupted - trash it/they and iMovie makes new and error free one's
• Creating a new User-Account and log into this - forces iMovie to create all pref. files new and error free
• Event or Project got corrupted - try to make a copy and repair
• a codec is used that doesn't work
• problem in iMovie Cache folder - trash Cache.mov and Cache.plist
• version miss match of QuickTime Player / iMovie / iDVD
• preferences are wrong - Repair Preferences
• other hard disk problem - Repair Hard Disk (Disk Util tool - but start Mac from ext HD or DVD)
• External hard disks - MUST BE - Mac OS Extended (hfs) formatted to work with Video
( UNIX/DOS/FAT32/Mac OS Exchange - works for most other things - but not for Video )
• USB-flash-memories do not work
• Net-work connected hard disks - do not work
• iPhoto Library got problems - let iPhoto select another one or repair it. Re-build this first then try to re-start iMovie.
This You do by
_ close iPhoto
_ on start up of iPhoto - Keep {cmd and alt-keys down}
_ now select all five options presented
_ WAIT a long long time
• free space on Start-Up (Mac OS) hard disk to low (<1Gb) - I never go under 25Gb free space for SD-Video (4-5 times more for HD)
• external devices interferes - turn off Mac - disconnect all of them and - Start up again and re-try
• GarageBand fix - start GB - play a few notes - Close it again and now try iMovie
• Screen must be set to million-colors
• Third-party plug-ins doesn't work OK
• Run "Cache Out X", clear out all caches and restarts the Mac
• Let Your Mac be turned on during one night. At about midnight there is a set of maintenance programs that runs and tidying up. This might help
• Turn off Your Mac - and disconnect Mains - for about 20-30 minutes - at least this resets the FireWire port.
• In QuickTime - DivX, 3ivx codec, Flip4Mac, Perian etc - might be problematic - temporarily move them out and re-try
(I deleted the file "3ivxVideoCodec.component" located in Mac HD/Library/Quicktime and this resolved my issue.)
buenrodri wrote
I solved the problem by removing the file: 3ivxVideoCodec.component. after that, up-dated iMovie runs ok.
Last resort: Trash all of iMovie and re-install it
Yours Bengt W

MacPro RAID card not initiating recovery after defective drive replaced

One of my artists is using an Early 2009 Mac Pro on 10.9.5 (13F1077). On Saturday morning, while he was not in the office, Drive 1 warned that SMART was reporting early signs of failure. The RAID card degraded the RAID set. I replaced Drive 1 and marked it as a global spare; but recovery is not initiating. I have, subsequent to installing the drive and marking it as a global spare, rebooted the Mac Pro; but the RAID Utility is not showing any Tasks running, and especially nothing about rebuilding the RAID set. As of now, the RAID set and RAID volume are not available. It appears that I can either try to preserve the data on the drives, or I can attempt to manually rebuild the RAID set; but not both. Unfortunately, the artist had all of his projects on the RAID and had not backed them up to servers at the time of the failure.

If a Disk Fails If a RAID set or volume becomes degraded because a disk has failed, you can use RAID Utility to identify the disk that needs to be replaced.
Note: If your RAID setup includes a spare drive, it is automatically incorporated into the RAID set, and the set switches from degraded to good as soon as the recovery process finishes. If there is no spare, the set will remain degraded until you replace the failed drive, and if a second drive fails before you replace the first, you could lose data.
To replace a failed disk:
1 Open RAID Utility, select the RAID set or volume that is displaying a problem status indicator, and look for a drive bay with a red status indicator. The bay numbers in RAID Utility correspond to the numbered drive bays in your Mac Pro or Xserve.
2 Replace the bad drive module.
3 Use the Make Spare command to set up the new drive as a global spare. If no spare was available when the original drive failed, the RAID card uses the new spare immediately to rebuild the affected RAID set and volumes. If a spare was available at the time of the failure, it is already incorporated into the affected RAID set, and the new spare remains available until it is needed.
https://manuals.info.apple.com/MANUALS/0/MA318/en_US/RAID_Utility_User_Guide.pdf

MacPro RAID card - best drives?

Hey, anybody have any experience they'd like to share on a good set of drives to go with the Apple RAID card? I want to get 4 and I'm looking for maximum speed, but I can't break the bank, so no Raptors.
cheers,
-r

Well, save your $$ and just DON'T! get the Apple RAID card, then you could afford some decent drives.
600GB 10K VRs $279 x 2
OWC SSD 100GB x 2
As for what drives, bare in mind -
If you read the Apple Support Mac Pro link to RAID card FAQ:
Question: *Which drives does Apple support for the Mac Pro RAID Card and the Xserve RAID Card?*
Answer: Only Apple SATA drives and Promise 450GB SAS Drive modules sold through the Apple Store are supported for use with the Mac Pro RAID Card (Early 2009) and the Xserve RAID Card (Early 2009). Apple 300GB SAS Drive modules are supported with the Mac Pro RAID Card (Late 2007) and Xserve RAID Card (Early 2007). Drives must be either all Serial ATA (SATA) or all Serial Attached SCSI (SAS) drives. SSD drive modules are not recommended for the Apple RAID Card because these drives use their own on-disk cache and cannot take advantage of the protection provided by the battery-backed cache on the RAID card.
http://support.apple.com/kb/HT1346#faq8
People do try and use retail SATA drives, with mixed results. I have never seen anyone mix SAS and SATA.

Erase old error messages of MacPro RAID Card?

Similar Messages

Maybe you are looking for