Error 10013 when using GPCTR_Control with ND_RESET
I am using two 6602 cards and a MIO E6035 in an PXI system. I program the counter and the MIO for bufferd operation and start the measurement. This works good.
Then I stop the actual measurement with DAQ_Clear for the MIO and GPCTR_Control with ND_RESET for each used counter on the 6602.
After a while I want so start a new measurement and do the same init again. The second time I often (not allways !!) get an error code 10013 (-10013 badErrorCodeError: The driver returned an unrecognized or unlisted error code) when I call ND_RESET.
Whe I get it once, I get it allways. WShen I stop my program and restart it, then the programming of the counters works aggain.
What can I do? Is there a command, so that I can init the
counter card completly?
I am using NI Daq 6.9.1.
Thanks
Stephan
Hi,
I have the similar problem with 3 6602 board and 1 6220.
Do you know how to reset the boards ? My application does acquier continusly without restarting.
Thank's
Similar Messages
-
Error 2170 when using Xcelsius with a web service
Hi,
I have built a small dashboard that gets data from a web service. When previewing it in XCelsius itself, the data is picked up without problem, but when exporting the file to PPT, Word or PDF, I get Error 2170 which is a connection error.
The Webservice I use a self-built one from a function module in an ECC6.0 system.
In the web (and her in SDN) I have found two solutions:
1) Flash settings. For Flash versions above 9.0, one has to allow connection to external programs. I have tried that but am not sure if I should allow connection for the PPT or PDF or for the .swf file "inside" (which I dont know the name of).
2) Server side. A crossdomain.xml file should be added to the root of the webserver. What folder would that be in the case of an ERP system and could I do that? Additionally: can the be the reason to my problem when the webservice works fine as long as called from within XCelsius?
I would be very grateful for ideas...
ThorbenThorben,
Here is what you need to do
-->Export your visualization to swf
-->Run the Swf, right click on visualization and got to settings.
OR
Click
http://www.macromedia.com/support/documentation/en/flashplayer/help/settings_manager04.html
In 3rd Tab (Global Security Settings)
--> Check box "Always Allow"
--> In the Drop down (Edit location... select Add Location
-->Browse the swf file
That is it...now reopen the .swf file, it should not throw error.
Hope this helps
-Anil -
ERROR MESSAGE WHEN USING PACK COMMAND Missing file ////presenter.css Command then fails
Also: "This course requires JavaScript to be enabled in your browser. Please enable JavaScript, then relaunch the course." I have Java enabled in all browsers
Thoughts? Using Presenter 10 Win 8.1 Intel I7 new HP with plenty of memory
ThanksI had saved one copy as an .asp but then resaved it to .xhtml
I'm assuming this is a static web site. Rename (F2) all your pages with .html or .htm extension.
.xhtml is not a valid extension.
Nancy O. -
Error message when using FM 'BAPI_BUPA_ADDRESS_CHANGE'.
I'm continually getting an error message when using FM 'BAPI_BUPA_ADDRESS_CHANGE'. The message being 'Table BAPIADTEL entry to be changed not found in target system'.
I have looked up this message but all links seem to refer to FM 'BAPI_BUPA_CENTRAL_CHANGE', which I'm not using, and has different parameter settings.
I'm simply trying to update the telephone number and I'm updating strcuture BAPIADTEL and BAPIADTELX but still the message appears. I know that there is a really simple reason for this, but I have been double-checking everything and experimenting with lots of different areas, but with no effect.
Has anyone encountered this problem using the specific FM ''BAPI_BUPA_ADDRESS_CHANGE' ?.
JasonHi Jason,
In case your database tables had already value for field telephone number, then only the flag should be "U".
If the telephone number field was empty, and we will try to change it by using the flag as U, it wont work. In this case, we should be using "I".
I even wrote that before in this post, but somehow I guess the post was locked, and a lot of comments from you and me were not visible apart from the first two. So, I couldnt get any update from you.
Anyway, its good that its working for you. Thank you for the update.
Regards,
Susanta -
Best practice when using Tangosol with an app server
Hi,
I'm wondering what is the best practice when using Tangosol with an app server (Websphere 6.1 in this case). I've been able to set it up using the resource adapter, tried using distributed transactions and it appears to work as expected - I've also been able to see cache data from another app server instance.
However, it appears that cache data vanishes after a while. I've not yet been able to put my finger on when, but garbage collection is a possibility I've come to suspect.
Data in the cache survives the removal of the EJB, but somewhere later down the line it appear to vanish. I'm not aware of any expiry settings for the cache that would explain this (to the best of my understanding the default is "no expiry"), so GC came to mind. Would this be the explanation?
If that would be the explanation, what would be a better way to keep the cache from being subject to GC - to have a "startup class" in the app server that holds on to the cache object, or would there be other ways? Currently the EJB calls getCacheAdapter, so I guess Bad Things may happen when the EJB is removed...
Best regards,
/PerHi Gene,
I found the configuration file embedded in coherence.jar. Am I supposed to replace it and re-package coherence.jar?
If I put it elsewhere (in the "classpath") - is there a way I can be sure that it has been found by Coherence (like a message in the standard output stream)? My experience with Websphere is that "classpath" is a rather ...vague concept, we use the J2CA adapter which most probably has a different class loader than the EAR that contains the EJB, and I would rather avoid to do a lot of trial/error corrections to a file just to find that it's not actually been used.
Anyway, at this stage my tests are still focused on distributed transactions/2PC/commit/rollback/recovery, and we're nowhere near 10,000 objects. As a matter of fact, we haven't had more than 1024 objects in these app servers. In the typical scenario where I've seen objects "fade away", there has been only one or two objects in the test data. And they both disappear...
Still confused,
/Per -
Adobe Air error message when using PSE 10
When I try using the tips in PSE 10 I get an error message from Adobe Air stating that it is damaged. Have tried uninstalling and re-installing, but that hasn't helped. I have windows 7
Okay Jeff, this is as far as I have gotten so far. I'm using Air version 3.2.0.2070. This is the install log.
Runtime Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -silent -eulaAccepted -programMenu AdobeHelp.air
Installed runtime (2.6.0.19120) located at C:\Program Files (x86)\Common Files\Adobe AIR
Invoking Application Installer for combined install
Launching subprocess with commandline C:\Users\Vette\AppData\Local\Temp\AIRD0CE.tmp\Adobe AIR\Versions\1.0\Adobe AIR Application Installer -runtime C:\Users\Vette\AppData\Local\Temp\AIRD0CE.tmp -silent -withRuntime -url -programMenu -eulaAccepted file:///E:/Adobe%20Photoshop%20Elements%2010/ElementsSTIInstaller/payloads/AdobeHelp/Adob eHelp.air
Application Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -runtime C:\Users\Vette\AppData\Local\Temp\AIRD0CE.tmp -silent -withRuntime -url -programMenu -eulaAccepted file:///E:/Adobe%20Photoshop%20Elements%2010/ElementsSTIInstaller/payloads/AdobeHelp/Adob eHelp.air
Installed runtime (2.6.0.19120) located at C:\Program Files (x86)\Common Files\Adobe AIR
Unpackaging file:///E:/Adobe%20Photoshop%20Elements%2010/ElementsSTIInstaller/payloads/AdobeHelp/Adob eHelp.air to C:\Users\Vette\AppData\Local\Temp\flaE4EA.tmp
Application signature verified
Unpackaging/validation complete
No app located for appID 'chc' and pubID '4875E02D9FB21EE389F73B8D1702B320485DF8CE.1'
Converting unpackaged application to a native installation package in C:\Users\Vette\AppData\Local\Temp\fla71A.tmp
Native installation package creation succeeded
Starting silent combined runtime update and app install.
Updating runtime from version 2.6.0.19120 to version 2.6.0.19140.
Installing app chc.4875E02D9FB21EE389F73B8D1702B320485DF8CE.1 version 3.5.23 to C:\Program Files (x86)\Adobe using the source file at file:///E:/Adobe%20Photoshop%20Elements%2010/ElementsSTIInstaller/payloads/AdobeHelp/Adob eHelp.air
Reinstalling C:\Users\Vette\AppData\Local\Temp\AIRD0CE.tmp\setup.msi
Installing msi at C:\Users\Vette\AppData\Local\Temp\fla71A.tmp\setup.msi with guid {BD7F1DA3-5EA0-65F8-52B0-5E103FDC045A}
Application Installer end with exit code 0
Subprocess app installer succeeded
Runtime Installer end with exit code 0
Runtime Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -silent "E:\Adobe Photoshop Elements 10\AdobePhotoshopDotcomInspirationBrowser.air"
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Invoking Application Installer for combined install
Launching subprocess with commandline C:\Users\Vette\AppData\Local\Temp\AIR4EA4.tmp\Adobe AIR\Versions\1.0\Adobe AIR Application Installer -runtime C:\Users\Vette\AppData\Local\Temp\AIR4EA4.tmp -silent -withRuntime -url file:///E:/Adobe%20Photoshop%20Elements%2010/AdobePhotoshopDotcomInspirationBrowser.air
Application Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -runtime C:\Users\Vette\AppData\Local\Temp\AIR4EA4.tmp -silent -withRuntime -url file:///E:/Adobe%20Photoshop%20Elements%2010/AdobePhotoshopDotcomInspirationBrowser.air
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Unpackaging file:///E:/Adobe%20Photoshop%20Elements%2010/AdobePhotoshopDotcomInspirationBrowser.air to C:\Users\Vette\AppData\Local\Temp\fla634C.tmp
Application signature verified
Unpackaging/validation complete
No app located for appID 'PhotoshopdotcomInspirationBrowser' and pubID '4C35C4D325D350FE0114230CBADCA2DDD0AC8D25.1'
Converting unpackaged application to a native installation package in C:\Users\Vette\AppData\Local\Temp\fla7325.tmp
Native installation package creation succeeded
Starting silent app installation to C:\Program Files (x86)\Adobe. Installing app PhotoshopdotcomInspirationBrowser.4C35C4D325D350FE0114230CBADCA2DDD0AC8D25.1 version 3.07 using the source file at file:///E:/Adobe%20Photoshop%20Elements%2010/AdobePhotoshopDotcomInspirationBrowser.air
Installing msi at C:\Users\Vette\AppData\Local\Temp\fla7325.tmp\setup.msi with guid {4C184855-B85A-6873-C642-60A58682E721}
Application Installer end with exit code 0
Subprocess app installer succeeded
Runtime Installer end with exit code 0
Launching subprocess with commandline C:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -updatecheck
Runtime Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -updatecheck
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/2.6.0.19140/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/2.6.0.19140/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Unpackaging complete
Download success
Runtime updated downloaded
User has selected immediate install of the update
Starting runtime background update installation
Launching subprocess with commandline C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background\updater -update
Runtime updater successfully launched
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.1.0.4880 on Windows 7 x86
Commandline is: -update
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Relaunching with elevation
Launching subprocess with commandline c:\users\vette\appdata\local\temp\airafa3.tmp\adobe air installer.exe -ei
Runtime Installer begin with version 3.1.0.4880 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_704_0 -ei
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Starting silent runtime update. Updating runtime from version 2.6.0.19140 to version 3.1.0.4880
Installing msi at c:\users\vette\appdata\local\temp\airafa3.tmp\setup.msi with guid {FE23D063-934D-4829-A0D8-00634CE79B4A}
Runtime Installer end with exit code 0
Elevated install completed
Runtime Installer end with exit code 0
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -updatecheck
Runtime Installer begin with version 3.1.0.4880 on Windows 7 x86
Commandline is: -updatecheck
Installed runtime (3.1.0.4880) located at c:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Clearing unused background update directory
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.1.0.4880/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.1.0.4880/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Runtime update not available
Unpackaging cancelled
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.1.0.4880 on Windows 7 x86
Commandline is: -arp:uninstall
Installed runtime (3.1.0.4880) located at c:\Program Files (x86)\Common Files\Adobe AIR
Runtime Installer end with exit code 6
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is:
Installed runtime (3.1.0.4880) located at c:\Program Files (x86)\Common Files\Adobe AIR
Relaunching with elevation
Launching subprocess with commandline c:\users\vette\appdata\local\temp\aire7af.tmp\adobe air installer.exe -ei
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_4784_0 -ei
Installed runtime (3.1.0.4880) located at c:\Program Files (x86)\Common Files\Adobe AIR
Starting silent runtime update. Updating runtime from version 3.1.0.4880 to version 3.2.0.2070
Installing msi at c:\users\vette\appdata\local\temp\aire7af.tmp\setup.msi with guid {47FA2C44-D148-4DBC-AF60-B91934AA4842}
Runtime Installer end with exit code 0
Elevated install completed
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -installupdatecheck
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -installupdatecheck
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Runtime update not available
Unpackaging cancelled
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -arp:uninstall
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Relaunching with elevation
Launching subprocess with commandline c:\program files (x86)\common files\adobe air\versions\1.0\resources\adobe air updater.exe -eu
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_3840_0 -eu
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Starting runtime uninstall. Uninstalling runtime version 3.2.0.2070
Uninstalling product with GUID {47FA2C44-D148-4DBC-AF60-B91934AA4842}
Runtime Installer end with exit code 0
Elevated install completed
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is:
No installed runtime detected
Relaunching with elevation
Launching subprocess with commandline c:\users\vette\appdata\local\temp\airbda4.tmp\adobe air installer.exe -ei
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_764_0 -ei
No installed runtime detected
Starting silent runtime install. Installing runtime version 3.2.0.2070
Installing msi at c:\users\vette\appdata\local\temp\airbda4.tmp\setup.msi with guid {47FA2C44-D148-4DBC-AF60-B91934AA4842}
Runtime Installer end with exit code 0
Elevated install completed
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -installupdatecheck
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -installupdatecheck
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Runtime update not available
Unpackaging cancelled
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is:
No installed runtime detected
Relaunching with elevation
Launching subprocess with commandline c:\users\vette\appdata\local\temp\air2fa8.tmp\adobe air installer.exe -ei
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_5396_0 -ei
No installed runtime detected
Starting silent runtime install. Installing runtime version 3.2.0.2070
Installing msi at c:\users\vette\appdata\local\temp\air2fa8.tmp\setup.msi with guid {47FA2C44-D148-4DBC-AF60-B91934AA4842}
Runtime Installer end with exit code 0
Elevated install completed
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -installupdatecheck
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -installupdatecheck
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Runtime update not available
Unpackaging cancelled
Runtime Installer end with exit code 0
Application Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -playerVersion=11,2,202,233 -sandboxType=remote -securityDomain=airdownload.adobe.com -https=false -fromUserEvent=true -- -url http://www.adobe.com/support/chc/air/350/AdobeHelp.air -- WWW aHR0cDovL3d3dy5hZG9iZS5jb20vc3VwcG9ydC9jaGMv
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Begin air file download from http://www.adobe.com/support/chc/air/350/AdobeHelp.air
Download destination is C:\Users\Vette\AppData\Local\Temp\fla7A97.tmp
Received download status 200
Response URL is http://www.adobe.com/support/chc/air/350/AdobeHelp.air
Download success
Unpackaging file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp to C:\Users\Vette\AppData\Local\Temp\flaB22B.tmp
Application signature verified
Unpackaging/validation complete
No app located for appID 'chc' and pubID '4875E02D9FB21EE389F73B8D1702B320485DF8CE.1'
Converting unpackaged application to a native installation package in C:\Users\Vette\AppData\Local\Temp\flaC7B.tmp
Native installation package creation succeeded
Starting app installation to C:\Program Files (x86)\Adobe. Installing app chc.4875E02D9FB21EE389F73B8D1702B320485DF8CE.1 version 3.5.23 using the source file at file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp
Got an unexpected fatal error while in stateInstalling: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="Unhandled exception Error: Directory can't be written to" errorID=5006]
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Adobe AIR Application Installer -runtime "c:\Program Files (x86)\Common Files" -silent -logToStdout -url -location "C:\Program Files (x86)\Adobe" -desktopShortcut -programMenu file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp
Relaunching with elevation
Application Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_4952_0 -runtime "c:\Program Files (x86)\Common Files" -silent -logToStdout -url -location "C:\Program Files (x86)\Adobe" -desktopShortcut -programMenu file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Unpackaging file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp to C:\Users\Vette\AppData\Local\Temp\fla3260.tmp
Application signature verified
Unpackaging/validation complete
No app located for appID 'chc' and pubID '4875E02D9FB21EE389F73B8D1702B320485DF8CE.1'
Converting unpackaged application to a native installation package in C:\Users\Vette\AppData\Local\Temp\fla3BF3.tmp
Native installation package creation succeeded
Starting silent app installation to C:\Program Files (x86)\Adobe. Installing app chc.4875E02D9FB21EE389F73B8D1702B320485DF8CE.1 version 3.5.23 using the source file at file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp
Installing msi at C:\Users\Vette\AppData\Local\Temp\fla3BF3.tmp\setup.msi with guid {BD7F1DA3-5EA0-65F8-52B0-5E103FDC045A}
Application Installer end with exit code 0
Elevated install completed
Launching subprocess with commandline C:\Program Files (x86)\Adobe\Adobe Help\Adobe Help.exe
Application Installer end with exit code 0
Date: Thu, 12 Apr 2012 17:10:46 -0600
From: [email protected]
To: [email protected]
Subject: Adobe Air error message when using PSE 10
Re: Adobe Air error message when using PSE 10
created by Jeff A Wright in Downloading, Installing, Setting Up - View the full discussion
Vetteski65 I would recommend reviewing Troubleshoot AIR installation | Windows - http://helpx.adobe.com/air/kb/troubleshoot-air-installation-windows.ht ml for steps on how to resolve your difficulties. Please feel free to respond to this thread if you have any questions about the steps listed within the document. If you could also respond with the specific error message you receive it would be appreciated.
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4331328#4331328
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4331328#4331328. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Downloading, Installing, Setting Up by email or at Adobe Forums
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746. -
Licence error message when using automation software
Error message when using Rational Functional Tester 7.0.1.1
to record a Flex application. The message seemed to come from the
Flex application.
I can record a fiew step in the application, then I have the
message : "Licence are not present. Eith the trial version only
limited record are allowed". But, my license of my Rational
Functional Tester application is activated.
I am using a Flex builder 3 trial version and the trial is
not over.
Is there any problem to get the license in the File compiler
with "D:\apps\IBM\SDP70\FunctionalTester\bin\rft.swc"? That RFT
file is supposed to be included in the flex application once
compileDoes anyone know how to build with automation support in a
linux environment?
We simply run an ant script build and have the SDK installed.
We purchased Flex Builder Professional, but cannot install on Linux
(we don't want to use the alpha version).
Thanks for any pointers :) -
My Application gets Error 37 when using Serial Port VIs.
My Application works fine developed with LV 6.1. Then I updated to LV 7.1 and now the Executable of my application gets error 37 when using the old serial port functions. The "serpdrv" file is located in the application directory and is from 02/2002. The application runs well in the development environment after I placed the "serpdrv" file in the LabView directory. I tried to put a line with "serialDevices=..." in the .ini-file of my application but this did not cause an improvement. I also tried to rebuild the EXE with this line in the "labview.ini" file but nothing changes.
Does anybody have another idea ?
Many thanks for help
Thomas>Did you actually replace the old serial functions that come with 7.1 with the functions from 6.1?
Yes. E.g. "open serial driver.vi" uses "open device" with "serpdrv" as device string.
I had the same problem running my application as VI´s. After the copy of serpdrv into the LV 7.1 directory everything works fine.
I don´t understand why the application running as a .exe doesn´t find the serpdrv when it is in the same directory....
Nevertheless many thanks for your answer
Thomas -
I'm getting a error message when using Apple Configurator "unable to send ClearPasscode command to device"
Yes, that is correct. My spreadsheet has the following information in those cells if you want to compare yours on Monday:
Product Type
Application
|
AdamId:
<and a 9 digit number>
I ended up bringing the Macbook Pro home with me after struggling with it for a half hour at the end of a long day. I called and within 5 minutes the problem was corrected. The technician said they were getting calls all day. -
Error 80 when using bluetooth on car radio
error 80 when using bluetooth on pioneer car radio with my iphone 4 and 5
me too...did some digging on the internet and appears Error -80 means the car deck is expecting some bluetooth protocols that your iPhones wont give out. mine was intermittent for last couple years (deck is 12 years old) as of last night i just get error -80 everytime i try to dial out or recieve a call via bluetooth. this issue was intermittent with an iPhone 3G, 4, 4S, 5 and now my current 5S. im blaming Pioneer not Apple for this
I ended up buying a new deck for my car...gets installed tomorrow. -
Error message when backing up with time on external hard drive
I'm running 10.6.8 OSX & wondering why I get an error message when backing up with time machine onto an external hard drive. Please help! Error message states time machine could not back up & to try again later.
Says "The back up was not performed because an error occurred while copying files to the backup disk.
"The problem may be temoporary. Try again later to back up. If the problem persists, use Disk Utility to repair back up disk." -
error -54 when synching iPad with iTunes on laptop.... what does this error mean?
Hey MacFromManila,
It's a different method of backing up your iPhone 4s. This article covers the differences between the two and may actually be able to help you choose between them:
Choosing an iOS backup method (Should I use iTunes or iCloud to back up my iOS device?)
http://support.apple.com/kb/HT5262
Cheers,
- Ari -
I keep getting an error message when installing iTunes with windows 8
See the second box in Troubleshooting issues with iTunes for Windows updates.
tt2 -
Error message when using xrpcc in JWSDP 1_0_01
Dear all,
I've got the following error message when using xrpcc of JWSDP 1_0_01 for my config.xml file.
D:\jwsdp-1_0_01\Message>xrpcc -classpath build -both -d build config.xml
error: invalid element "{http://java.sun.com/jax-rpc-ri/xrpcc-config}configurati
on" in configuration file (line 2)
The content of 'config.xml' is shown as follows.
<?xml version="1.0" encoding="UTF-8"?>
<configuration xmlns="http://java.sun.com/jax-rpc-ri/xrpcc-config">
<rmi name="MessageService"
targetNamespace="http://messageuri.com/wsdl"
typeNamespace="http://messageuri/types">
<service name="MyMessage" packageName="Message">
<interface name="Message.MessageIF"
servantName="Message.MessageImpl"/>
</service>
</rmi>
</configuration>
Thank you for your kind attention!
Regards,
EddieThanks all! I've already solved my previous problem, however, i got another one now.
=========================================================
error: unknown model info in configuration file (line 5)
=========================================================
<?xml version="1.0" encoding="UTF-8"?>
<configuration xmlns="http://java.sun.com/xml/ns/jax-rpc/ri/config">
<rmi name="MessageService"
targetNamespace="http://messageuri.com/wsdl"
typeNamespace="http://messageuri.com/types">
<service name="MyMessage" packageName="Message">
<interface name="Message.MessageIF"
servantName="Message.MessageImpl" />
</service>
</rmi>
</configuration>
Thanks,
Eddie -
Error message when using search
why do i keep getting an error message when using the "search" tabe in iTunes. This happend whe i upgraded t the latest version of itunes.
Well, I believe JHeadstart does not really have this functionality.
One way is use a Query Operator 'startsWith', but then you always query like LIKE '<entered search value>%'
This is probably not what you want...
But you could hack it into advancedSearch in YourApplicationModuleImpl
try {
if (viewCriterium.getQueryValue() != null) { //This is where exception JHS-00116 is raised...
value = viewCriterium.getQueryValue().toString();
} else {
value = null;
catch (NumberFormatException ex) {
//insert check for wildcard
value = viewCriterium.getValue().toString();
if (value.indexOf('%')>=0) {
sLog.debug("Ja, een wildcard!!!");
operator = "LIKE";
} else {//original exceptionhandling code here...
...and a bit later, add test for "LIKE":
if (viewCriterium.isDate() || viewCriterium.isString() || "LIKE".equals(operator)) {
value = "'" + value + "'";
very nasty code, and does not raise an exception for searches like '%xxx'
Good luck,
HJH
Edited by: HJHorst on Mar 5, 2009 12:03 AM
Maybe you are looking for
-
SOAP Responce cannot be decoded after during a long web service exection
I have an AIR application. I am using the spark web service and i have set up a fualt handler and set the requestTimeout to 0. I call an opertaion that calls a .Net web service. Inside that .Net web service i run a very heafty SQL using ADO and then
-
How do I upgrade my MacBook Pro from OS10.5.8 to the lastest software, which I believe is 10.7? This is a company computer and the guy who had it before me never kept up with updates. Now I have some audio hardware whose software will only operate wi
-
Greyed-out movie file not syncing
I imported a short MP4 video file into iTunes 10 for Windows. (An old educational short from RiffTrax if you're interested) It appears in iTunes okay and plays fine, but when I attempt to sync my iPhone 4, the title for that video file is greyed out
-
Changing InfoObject to enable document attribute of a characteristic
Hi, We have a need to change existing infoObject. Currently it's not document attribute and we need to enable "Characteristic is document attribute" in infoobject maintenance. But, the characteristic that we are trying to change is used all over (aro
-
AUC settings with Internal Order
Hi, Can you please give me the steps of AUC setting with Internal Order. Regards Abhi