Error 104 unsupported network device!!!!!!

I've bought a new wireles mini pci network card.
I put it in my laptpop and all i get is error 104 unsupported network card detected.
Help!!!!!!

Hi:
if you did not purchase a supported wireless adapter that is listed in your notebook's service manual with the HP part number on it that is why you got the error.
HP locks out of the BIOS any wireless cards that are not listed in the service manual.
This method is how HP has chosen to comply with wireless communications regulations regarding SAR and interference. Cards and notebook antenna systems have to be tested and validated to work within certain measurements.
More information regarding this can be found in this document below:
While this specifically deals with US regulations, other countries also have similar regulations, I'm sure.
Since HP is a US based company, it complies with US regs.
http://fjallfoss.fcc.gov/kdb/GetAttachment.html?id=22884
There is nothing you can do except to remove the card.
Paul

Similar Messages

My pavillion dv2410us stops at an error message 104 unsupported wireless network device detected.

error at start for hp dv2410us stops at black screen with the next error message
error 104 unsupported wireless network device detected. System halted. remove device a start

Hi:
Did you just install a wireless card? You get that error if you install an unsupported wireless card. If you did not make any changes to your PC then I don't know what to tell you.
Paul

104 Unsupported Wireless Network Device Detected

Opening up the computer this morning i have a message that says: 104-Unsupported wireless network device detected. System halted. Remove device and restart.
There are no additional devices added or changed before putting laptop in hibernation for the night last night. Odd. Any suggestions?

Hi
In case you are comfortable reseat the Wireless card from the back panel also try to visit HP website and update the Bios for your unit and see if this fixes your issue.
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

104-unsupported wireless network device detected - yet replaced with like for like card!

Hi,
I am repairing a friends laptop where their wireless is no longer working.
I ordered a new card on ebay which is the same model Broadcom BCM4311KFBG however I still get the above message.
How is it not accepting this card? Surely it's in the whitelist? It is exactly the same card except for the original had a "P20" stamped on the chip (as well as the BCM4311KFBG model number) and this new one had "P11".
Any help much appreciated.
Thanks
This question was solved.
View Solution.

HP6715b.
The one on the left is for HP.
The one on the right is for DELL.
Both are BCM4311KFBG.
http://www.ebay.com/itm/Broadcom-BCM4311KFBG-Mini-PCI-express-Wireless-WLAN-Wifi-Card-802-11-For-HP-...
Ebay $7.99 free shipping.
REO
HP Expert Tester "Now testing HP Pavilion 15t i3-4030U Win8.1, 6GB RAM and 750GB HDD"
Loaner Program”HP Split 13 x2 13r010dx i3-4012Y Win8.1, 4GB RAM and 500GB Hybrid HDD”
Microsoft Registered Refurbisher
Registered Microsoft Partner
Apple Certified Macintosh Technician Certification in progress.

Unsupported wireless network device detected

Hi guys,
I had to change the motherboard of my DV9420US; I bought a new motherboard from Megabyte Trading, the part number was the same (444002-001) and they told me it was an HP piece. However, after the technician replaced it, the following error appears when booting and forces me to shut down:
"104-unsupported wireless network device detected. System halted. remove device and restart".
Can anyone tell me how to fix this problem?
It starts to be disappointing: I have already spent over 400 bucks to repair the original motherboard first and buy a new one after, with the result that my laptop does not work yet.
Thanks.
simone73
This question was solved.
View Solution.

Remove the wireless card and boot into the notebook. Once into windows you will have to hardwire the notebook into an internet connection and go to HP.com. Place your PN number in the search and go to the software and driver downloads find the BIOS header and download the most update BIOS and flash the BIOS for the notebook. Once this has completed replace the WLAN and boot it back up, should fix the issue.

"Warning Unsupported wireless network device detected.Please remove device and restart"

Okay, so i went upnorth with my family and my Lenovo 3000 c100 worked perfectly one night, the next morning I woke up and turned on my laptop and i got this message "Warning Unsupported wireless network device detected. System halted. Please remove device and restart". I've tried to boot into bios it wouldn't let me. It says to interrupt normal startup press the lenovo care button???, i'm guessing it's the wrench with a square around it located near the power button?. I have found nothing to fix this problem and i need my laptop for work tomorrow.
Please help.
Thank you

The same problem hapend to me today. I just start the notebook and I'm getting the red message: "Warning Unsupported wireless network device detected.Please remove device and restart" .
I search the internet and I didn't found anything. I have the same problems like you guys... very strange message And no one knows the answers .
Please HELP!!

SCOM Monitoring Multiple interface of a same network device

hi
I have deployed SCOM 2012 R2. I have discovered around 200 network device by using device's loopback IP adress with SNMP v3.
100 dvices are in the branch offices those are connected with 3 links in three interfaces respectively. Even if two link is down, i can see that my network device is healthy since network device is discovered with the loopback address. How can i configure
my network monitoring so that even if one link goes down i can see some kind of warning or error in the particular network device in my monitoring pane. Please say if my infrastructure is unclear.

Hi,
You can create built-in network ICMP only network monitoring for the three interfaces respectively.
Using the built-in network monitoring within Operations Manager 2012 to monitor network devices using ICMP only mode
http://blogs.catapultsystems.com/cfuller/archive/2013/07/03/using-the-built-in-network-monitoring-within-operations-manager-2012-to-monitor-network-devices-using-icmp-only-mode-scom-sysctr.aspx
Note: Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

ACS 4.1.1.24 to 5.2.0.26.3 Network Device Migration issue

Hello all.
I'm getting an error when I run the migration.bat script to migrate data from ACS 4.1 to 5.2 and analyse the Network Devices in the 4.1 database.
hqssec01
AnalyzeAndExport
Network Device
hqsvg22417k
error
invalid_sharedsecret
Cannot migrate Network Device that has Shared secret key with a name that contains any of the following characters: "'{}
hqssec01
AnalyzeAndExport
Network Device
hqsvg22418k
error
invalid_sharedsecret
Cannot migrate Network Device that has Shared secret key with a name that contains any of the following characters: "'{}
hqssec01
AnalyzeAndExport
Network Device
milswi1a1
error
invalid_sharedsecret
Cannot migrate Network Device that has Shared secret key with a name that contains any of the following characters: "'{}
hqssec01
AnalyzeAndExport
Network Device
DS2000_Storm_Standby
error
invalid_sharedsecret
Cannot migrate Network Device that has Shared secret key with a name that contains any of the following characters: "'{}
We use a common shared secret key for 253 devices to use for TACACS authentication. Unfortunately ACS 4.1 allows you to use the " character in this key but 5.2 doesn't. Is there a way of changing the key in the 4.1 database for all 253 devices without having to manually change all devices individually?
I can change the AAA client's key with various tools no problem, but the issue is the key stored on the ACS database.
Any help would be great!

Just to update.
RDBMS syncronization using csv files is only available on 4.2 so I updated from 4.1 to 4.2.
Using the accountActions.csv file, I made a copy accountActions2.csv and used the action id 225 to dump the NAS database to a file DumpNAS.txt.
I then imported the relevant fields from DumpNAS.txt into a new file accountActions3.csv and used action ID 224 to update the NAS database.
The issue I had was that the Value 3 field "Vendor ID" I could not locate the corrent string to use.
In the end I used the 'File Operations' function in ACS 5.2 and used the network device template to load the devices into ACS 5.2 with the new shared secret. The only thing missing from was Network Device Groups, which had to be created manually and then manually move each device into the relevant NDG.
This may prove useful for anyone having a similar problem.

Network Device Usermode I/O Protocol and ConfigFree error

I have a Toshiba laptop and recently it has not started properly, displaying the following message: "Not found TOSHIBA Network Device Usermode I/O Protocol. Please reinstall ConfigFree. OK".
I am unable to use the laptop and it will not shut down without being forced (though once it did shut down and restarted OK, and then worked fine for three days We left it over Xmas and now it is doing it again). Can anyone let me know what this error message means and how I can deal with it (I know little about the workings of my laptop!).
We have Windows XP and are set up to a wireless broadband connection. I would be wonderfully happy if I could sort this as I have been forced to travel to work rather than work from home today because of it!!!!
Thank you in advance!

Hi
The message is clear.
> Please reinstall ConfigFree.
So why didnt you reinstall this utility???
If you didnt create the Tools & Utility CD you can download this utility from the Toshiba driver page.
Then remove the ConfigFree from the Add & remove programs, reboot the unit and install the ConfigFree again.

Failover Cluster Validation Report Error with IBM USB Remote NDIS Network device

We are setting up Microsoft Windows Server 2008 R2 Failover Cluster on IBM X3850 X5 and get errors in the Failover cluster Validation Report due to the IBM USB Remote NDIS Network Device is using APIPA adresses and both servers are using same APIPA-adresse.
How should I configure the Server and OS for the Failover cluster to be MS approved?
IBM don't recommend that i disable the Network device, but it is a possible solution!?!

What I did was use ipconfig /all to see the settings it is using and then when and set the ip setting on the NDIS driver to be that except I increment the last value by 1 for each node so that they do not have the same IP address. I ran the
cluster validation again and it came up clean and I have not experienced any issues yet. It does give warnings about it being an Automatic Private IP Address and should not be used, which is ok because we are not going to use it anyways.
Rich Baumet

ISE Failed to Create Network Device Error

I am trying to add new network device to a new out of the box ISE 3315 appliance under the Administration > Network Resources section. I was able to do this the other day but now when I try I get an error that says "Failed to create network device. System Error!
Any ideas? I tried a reboot, and Iam pretty certain I was able to do this a few days ago. Its a lab device so only I have touch it. Only other thing I can think to add is that I am running on an eval license until my regular licenses arrive. From what I see I have 81 days left on my base and advance package eval licenses.

Is there a certain amount of AAA client for that eval license?
Thanks,
Scott Fella
Sent from my iPhone

Network Devices: id 11009 Error in SNMP GET response from IP Address:, Status: noSuchInstance(129).

Hello,
I'm having this error since i started monitoring network devices. Currently i have 14 Network devices (Cisco Switch). I have the SCOM 2012 R2.
The same error appear for a lot of workflows:
OID: .1.3.6.1.2.1.2.2.1.12.10609
Workflow name: System.NetworkManagement.MIB2_ifMIB_dot3Ethernet.Port.InputPacketBroadcastPct
Workflow name: System.NetworkManagement.DeltaRule.MIB2.NetworkAdapter.ifInNUcastPktsRate
Workflow name: System.NetworkManagement.MIB2_dot3.NetworkAdapter.HighOutputErrorRate
Workflow name: System.NetworkManagement.MIB2_Base.NetworkAdapter.InputPacketDiscardPct
Workflow name: System.NetworkManagement.MIB2_ifMIB_dot3Ethernet.Port.HighInputBroadcastRate
OID: .1.3.6.1.2.1.2.2.1.18.11104
Workflow name: System.NetworkManagement.MIB2_dot3.NetworkAdapter.OutputPacketErrorPct
Workflow name: System.NetworkManagement.MIB2_dot3.NetworkAdapter.HighOutputErrorRate
Workflow name: System.NetworkManagement.DeltaRule.MIB2.NetworkAdapter.ifOutNUcastPktsRate
System.NetworkManagement.MIB2_Base.NetworkAdapter.HighInputDiscardRate
Anyone knows a solution? This is generating a lot of alerts. What can i do to stop this workflow?
Thanks,
Rui

Hi,
If we can find the corresponding device according to the OID, and then we could override the monitor or rule for this specific device.
And here is a similar thread about how to monitor Cisco device based on OID, please go through it:
http://social.technet.microsoft.com/Forums/systemcenter/en-US/5e806aa2-c90d-4b39-9ef2-4cfc003e68ff/snmp-monitor-based-on-oids?forum=operationsmanagerauthoring
In addition, have you tried the possible resolution for event 11009 as below in the link I provided in my first post:
Possible Resolutions
Stale Discovery Data – Device has been reconfigured since the last discovery and Operations Manager is attempting to monitor a component that no longer exists on the device.
If the device doesn’t support the workflow, then a solution is to disable the workflows utilizing the value for the device. This will prevent these workflows loading and failing in the future.
Possibly a device issue, try updating the Firmware and OS on the device
Possible a discovery issue where the instance is being discovered incorrectly. For example Operations Manager is expecting to monitor a performance counter but this is a virtual interface and the counters are not present for the interface. Try
running a re-discovery for the device.
Regards,
Yan Li
Regards, Yan Li

Error importing network device using CSV file

While importing a CSV file of a single network device, I am getting this error:
Value for attribute TrustSecDeviceID is Mandatory
In the CSV template (downloaded from ISE web gui), I don't see a field TrustSecDeviceID. What is the error referring to?

Kashish,
This looks like a bug but I attached a template that you can use and i tested with my ise 1.1.1 patch 1 and it worked fine, just replace the fields that I entered and you should be good to go! Were you able to get the password reset successfully on the PSNs?
Good luck!
Tarik Admani
*Please rate helpful posts*

Network Device Support Service logging errors

The following error is logged for to six times per hour.
The HP Network Devices Support service terminated with the following error:
The specified module could not be found.
XML Detail is:
- <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
- <System>
<Provider Name="Service Control Manager" Guid="{555908d1-a6d7-4695-8e1e-26931d2012f4}" EventSourceName="Service Control Manager" />
<EventID Qualifiers="49152">7023</EventID>
<Version>0</Version>
<Level>2</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x8080000000000000</Keywords>
<TimeCreated SystemTime="2014-08-02T03:21:54.757140700Z" />
<EventRecordID>1447175</EventRecordID>
<Correlation />
<Execution ProcessID="756" ThreadID="8396" />
<Channel>System</Channel>
<Computer>MarvOfc</Computer>
<Security />
</System>
- <EventData>
<Data Name="param1">HP Network Devices Support</Data>
<Data Name="param2">%%126</Data>
<Binary>4800500053004C0050005300560043000000</Binary>
</EventData>
</Event
Already having problem upgrading to Win 8.1 from 8.0 and this isn't helping. Anyone know what I can do to stop the errors? (This post also generated an error stating that invalid HTML was detected and removed and it was a direct copy from the Microsoft error log.)

So what you're telling me is that it's a WINDOWS FILE that the HP Service is looking for? When it's an HP Service that will not start, and not a windows service that won't start? So why are the printers functioning properly, and listed in the proper places (meaning my system sees the P2015dn on the network and uses it with no problems), but the HP service is logging errors? FYI, the only HP network device I have is the printer.
You'll have to explain that one before I go to the trouble of doing a full backup and a clean install of Windows 8, then a full restore. You're talking HOURS AND HOURS here with no gaurantee of success, and I suspect having nothing to do with the real problem of a missing file that is probably authored by HP, not Microsoft.
It's beginning to look like you guys don't know what file it's looking for either. If it's actually a real windows .dll file and you know which one, I should be able to extract it from the windows disk to the proper folder and register it if needed.

104 unsupported wireless device detected

I replaced my motherboard with the exact model and now it does not recognize the wireless card. if i take it off the machine boots and i insert the card and it works fine.
OS Name Microsoft® Windows Vista™ Business
Version 6.0.6000 Build 6000
Other OS Description Not Available
OS Manufacturer Microsoft Corporation
System Name AMY-PC
System Manufacturer Hewlett-Packard
System Model HP Pavilion dv6000 (RR723EA#UUW)
System Type X86-based PC
Processor AMD Turion(tm) 64 X2 Mobile Technology TL-60, 2000 Mhz, 2 Core(s), 2 Logical Processor(s)
BIOS Version/Date Hewlett-Packard F.43, 3/22/2010
SMBIOS Version 2.4
Windows Directory C:\Windows
System Directory C:\Windows\system32
Boot Device \Device\HarddiskVolume1
Locale United States
Hardware Abstraction Layer Version = "6.0.6000.16386"
User Name Amy-PC\Amy
Time Zone Eastern Standard Time
Total Physical Memory 3,070.00 MB
Available Physical Memory 2.05 GB
Total Virtual Memory 6.18 GB
Available Virtual Memory 5.31 GB
Page File Space 3.29 GB
Page File C:\pagefile.sys
the wireless card is AR5XB63-H part number 459339-01.
I have flashed the bios, reset bios to default, updated card drivers, reinstalled the o/s and no luck.. please help..
Dlo

Hi,
Can you you please find something from Amazon.com? As I can return, if does not work for my laptop? (Anything sold by Amazon or in Amazon-Marketplace are return warranted). But eBay is not. Please note I have AC and N type Router bandwidth. Please find only a AC or N type card as I have AC router.
I found couple of them in Amazon.com as follows:-
This is a N type:
http://www.amazon.com/dp/B002OB0FPI/ref=wl_it_dp_o_pC_nS_ttl?_encoding=UTF8&colid=1FAGLY8FX8L7J&coli...
This one is AC & N Type:
http://www.amazon.com/dp/B00IOS19E6/ref=wl_it_dp_o_pC_S_ttl?_encoding=UTF8&colid=1FAGLY8FX8L7J&colii...
This HP Part I Purchased and did not work for me.. ! Gave me "104-Unsupported.."
http://www.amazon.com/gp/product/B009GAJ3YY/ref=oh_aui_detailpage_o01_s01?ie=UTF8&psc=1

Error 104 unsupporte​d network device!!!!​!!

Similar Messages

Maybe you are looking for

Error 104 unsupported network device!!!!!!