Error 1069 on Invoke Node

Hello all,
I'm trying to build an application we have. In one of the sub-vi's there's a call to invoke node to start another vi. When I run the program from the VI this works fine as it should. When I build my executable and have my .llb for the executable, the program gets to this point and I get the above error, Error 1069: The sub vi is not executable. I know there's no executable for this and the spawn vi that calls it is in the llb. Any ideas as to why it will work as a vi but not as an exe? Thanks for any help.
Gary

Aaron G wrote:
Gary,
A common reason for error 1069 is because you are attempting to launch the code from the executable environment and not a develoment environment. When it attempts to launch the VI, it may not find all of the subVIs, causing the VI to be reported as non-executable. One way around this is to open the VI that is dynamically launched, go to File>>Save With Options and choose Application Distribution. This will allow you to create an Application Distribution LLB file. If your executable launches the version of the VI that is in the Application Distribution LLB, it will work. As a word of caution, when saving files as an Application Distribution, the block diagrams are removed from the VIs, DO NOT OVERWRITE your existing VIs. You will never be able to edit them again if you do this. Alternatively, when you build the application, make sure that the VI is included as a dynamically launched VI in the list of included files.
Regards,
Aaron
Aaron, thanks for the reply. I am saving with options and doing the Application Distribution. I'm also getting error 1003 but it's still saying the possible cause may be that the vi is not executable. The vi's that the invoke fails on are not included in the llb but according to the previous version of the software (in LV 6.1) it's not needed. (I checked the old llb file and the options in application builder.) I have the spawn vi which calls the invoke in the llb. The spawn takes a path, creates a reference and then does the invoke on this path. The vi's themselves are not in the llb. Will these need to be moved in? And if so will the paths need to be changed?

Similar Messages

  • Error 6 at Invoke Node in Dist Send Result File to RT.vi-- Bu​ild Applicaito​n.vi

    I am using cFP 2000 RT in my application. When I build exe and download the application to the cFP 2000 RT, I get "Error 6 occured in Invoke Node in Dist Send Result File To RT.vi--> Build Application.vi"
    The steps followed.
    1. In the LabVIEW 7.0 Main Panel, Select the execution target as RT Target.
    2. Tools --> Build Application or Shared Library. In the Target Tab the destination directory is selected as \\xxx.xxx.xxx.xxx\c\ni-rt\startup automatically.
    3. In the SOurce file tab, select the Top level VI.
    4. Press Build to make the executable of the application. The application is built and at the end the error message is poped up. (see the attached file)
    Software Configuratio
    n:
    1. LabVIEW 7.0
    2. Field Point 4.0
    3. LabVIEW RT 7.0
    Help me solve this problem. Thanks in advance.
    Attachments:
    Error_Message_and_RT_Info.bmp ‏313 KB

    This is most likely coming from the specific file it mentions in the error, Dist Send Result File To RT.vi. The error 6 means the file can't be found. One thing to try first is to add this VI as a Dynamic VI in Application Builder. Another option is to change the path that this VI is invoked from, or is not called by an Invoke Node at all.
    I hope this helps, feel free to contact support if the problem continues.
    Regards,
    Robert Jackson
    Application Engineer

  • Error 10000 at invoke node

    There is an Error 10000 happened at invoke node in one of my subvi. Please see attached snapshot of the error message.
    This program(VI) has run for one month, and yesterday  this error happened first time.  After I stopped the VI, and ran it  again, there was no error anymore.
    Can anybody tell me possible causes?  Thanks.
    WT
    LV2013SP1
    Attachments:
    Invoke Node error at CallSubVI_Do.PNG ‏36 KB
    Call_Subvi_Do(variant).vi ‏20 KB

    weitong wrote:
    Thanks. But, I didn't get what you said.
    I am using "Call_Subvi_Do(variant).vi " to open and run another VI.  Which one I should check the state of by using the Property node "Execution>State>Idle",  "Call_Subvi_Do(variant).vi" OR the VI called by Call_Subvi_Do(variant).vi? By the way, the error is promted happening at the Invoke node in "Call_Subvi_Do(variant).vi" .
    Yes on the top its happens in the sub VI but when you debugg the sub VI you may find that error occuring at the onvoke node "Run VI". Check the attached VI with added check for the state of the VI.
    The best solution is the one you find it by yourself
    Attachments:
    Call_Subvi_Do(variant)_Anand.vi ‏21 KB

  • Error 1 at Invoke Node

    This VI was always working perfectly and no changes have been made to it but yet i am now seeing an error.
    Any ideas?
    Attachments:
    TBIMon_EmailAsynchronus.vi ‏32 KB

    Misspelling would cause you problems.
    There are only two ways to tell somebody thanks: Kudos and Marked Solutions
    Unofficial Forum Rules and Guidelines

  • Error 7 in Invoke Node in 'Dist Build App from LLB.vi'

    I am encountering this error when trying to build an application. The error occurs while the builder is indicating that the application is actually being built (after files have been copied to the application). I am positive that all of my file paths are correct. I also have successfully mass compiled all of the VIs in the application. Is there something I'm overlooking?
    The really funny thing is, using this same .bld script, I successfully built the application on another computer (running LV 7.0, just like this one).
    My ideal approach to solving this problem would be to get into 'Dist Build App from LLB.vi' (or it's caller) and take a look at exactly which VI in my build is tripping up the build process.
    Does anyone know the path for the LLB where I can find these VIs? And will I be able to access their block diagrams?
    Thanks,
    Nick
    "You keep using that word. I do not think it means what you think it means." - Inigo Montoya

    I just fixed the problem. When I said I was positive that all of the paths were correct, I was talking about paths to the LLBs in my build. However, somehow the LabVIEW system paths got changed. I don't recall ever doing anything to change LV's seach paths. I reset to the default values in Tools>>Options... and everything seems to work now. Sorry for the trouble, and thanks for the quick response, A.
    -Nick
    "You keep using that word. I do not think it means what you think it means." - Inigo Montoya

  • Method Not Found Invoke Node error 1316 using Solid Works IEdm

    Hi Forum members,
    I have been having a problem with calling a function in a dll file.  I have attached the VI as example.  When I use the GetFile method I get a reference to that.  I then use the Invoke node and recieve a list of methods, the first of which is ChangeState.  I select this method and wire all required inputs and when I run the program I receive the error at that invoke node that the method does not exist.  How is this possible?  I have tried various methods to ensure the inputs are all correct and none have worked.  I do not believe the fault lies in the inputs, but I cannot for the life of me find the problem...  Perhaps someone has experience using Solid Works in Labview?  Any help would be appreciated.!!
    Cheers
    Ben
    Attachments:
    SetFileSatus.vi ‏18 KB

    I have determined that there is a problem with the Invoke node not recognising the function.  This is a Labview problem as the function is listed and selectable, so when the error comes saying the function is not found, this is a problem with Labview and not the dll.  The Function when selected also has the right input parameters that automatically appear.  How is it then that the method is not found when the program is run?

  • Invoke node wiring "weird" error

    Greetings NI community,
        I know I have posted a lot about going from I2C to USB communications, and right now I am currently programming another controller in addition to the USB 8451, namely the Diolan DLN-2 - http://www.diolan.com/products/dln2.html.
       Now basically I'm trying to assemble my LabVIEW code that I've written before to work with Diolan, and Diolan has been of tremendous help - same level as NI!
       But I was trying to run this code (attached), but I get an unwired or bad terminal error at both invoke nodes (read and write - 2 errors - 1 for each) - but there's nothing to wire to/from, and the Diolan Engineer assisting me - his works fine (screeshot attached). It's the same exact code, I just cleaned mine up a bit, but didn't make any changes.
       Is there something I have to enable on my end for my code to run?
       Thanks!
        TheLT
    Solved!
    Go to Solution.
    Attachments:
    i2c-master-configure.vi ‏17 KB
    i2c_master-read_write.jpg ‏73 KB

    TheLT wrote:
    Greetings NI community,
        I know I have posted a lot about going from I2C to USB communications, and right now I am currently programming another controller in addition to the USB 8451, namely the Diolan DLN-2 - http://www.diolan.com/products/dln2.html.
       Now basically I'm trying to assemble my LabVIEW code that I've written before to work with Diolan, and Diolan has been of tremendous help - same level as NI!
       But I was trying to run this code (attached), but I get an unwired or bad terminal error at both invoke nodes (read and write - 2 errors - 1 for each) - but there's nothing to wire to/from, and the Diolan Engineer assisting me - his works fine (screeshot attached). It's the same exact code, I just cleaned mine up a bit, but didn't make any changes.
       Is there something I have to enable on my end for my code to run?
       Thanks!
        TheLT
    Can you show us the error messages please?
    Ben
    Ben Rayner
    I am currently active on.. MainStream Preppers
    Rayner's Ridge is under construction

  • Excel ActiveX invoke nodes are broken

    I am using LabVIEW 2007.  We are using a VI that runs on most of the PC's in our facility however on some the "invoke node" related to Excel functions don't operate. They are broken and the VIs won't run.  We get errors that the "Invoke Node: contains unwired ro bad terminals".  When going to select methods or properties not all of the properties are shown as seen on the functional PCs. Some of the properties are missing from the selection menus, thus making it incompatible.
    Has anyone seen this problem and a solution?
    Thanks
    Manliff,

    What about separating the compiled code from the source?  I recognize that this will only work in LV2010, but I expect that that will prevent the compiler from breaking activeX code that depends on a different version than the local one...
    Testing this idea is on my to-do-list, but I was wondering if anyone has tried it already.
    -Barrett
    CLD

  • "Error 7 occurred at Invoke Node..." when attempting to open .vi for editing

    I am attempting to open a vi for editing, and instead the vi is attempting to execute.  I get the error:
     "Error 7 occurred at Invoke Node in BuildTargetBuildSpecification.vi->BuildXFS.vi"    
    Possible reason(s):   LabVIEW:  File not found. The file might have been moved or deleted, or the file path might be incorrectly formatted for the operating system. For example, use \ as path separators on Windows, : on Mac OS, and / on Linux. Verify that the path is correct using the command prompt or file explorer.
    Method Name: Project: Open
    When I close the Error Message dialog, Labview terminates.

    Hi R.Jay,
    Error 7 generally occurs when trying to create an executable when there is an extra instance of a top-level vi.  You may need to remove the file as a support file (but leave it as the top level vi).
    Are you trying to run an executable that has already been created?  Unless you have already built an executable, it should not automatically run when opened.  Also, was it built in a previous version of LabVIEW?  Sometimes this error can be seen when you upgrade to a newer version without compiling.
    Regards,
    Lauren
    Applications Engineering
    National Instruments

  • Build error after upgrading from 8.2.1 to 8.5 "Error 1055 occurred at Invoke Node..."

    After upgrading to 8.5, I'm getting the following error when trying to build an EXE:
    Visit the Request Support page at ni.com/ask to learn more about resolving this problem. Use the following information as a reference:
    Error 1055 occurred at Invoke Node in AB_Source_Library.lvclass:Close_Reference.vi->AB_Build.lvclass:Copy_Files.vi->AB_Application.lvclass:Copy_Files.vi->AB_Build.lvclass:Build.vi->AB_EXE.lvclass:Build.vi->AB_Engine_Build.vi->AB_Build_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller
    Possible reason(s):
    LabVIEW:  Object reference is invalid.
    I have been building this application for both Windows and Mac OS, and I even get the same error when building the .app on an Intel Mac.
    Things that I've already tried:
    * Mass-compiling all my code
    * Created the project from scratch
    * Enabled each panel of the "diagram disable structure" one at a time and compiled again
    Any ideas?

    Hi Travis,
    Ben’s advice if definitely the best place to start. Error 1055 is a very general LabVIEW error for “Object reference is invalid.” The cause is usually a bad install where important LabVIEW function aren’t placed in the right directory or aren’t installed at all.
    Charlie M. CLD

  • Error 1003 occurred at Invoke Node

    Good morning.
    I work with LW8.5 and created with the following architecture:
    There is main.vi on the links at the user's calls and runs the other VI.
    That is, not directly, these are not included in the VI block diagram main.vi.
    In the development of a happening in normal mode, all dynamically called VI,
    But once I make EXE, when you try to call the dynamic VI error 1003.
    Error 1003 occurred at Invoke Node in Main.vi
    Possible reason (s):
    LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the VI in LabVIEW using File>> Open and verify that it is runnable.
    VI Path: C: \ Shaikov \ Labwiev \ builds \ NSIAES \ Initialsettings \ Initialsettings.vi
    Show you how to act?
    Thank you.

    Hello margasan.
    In my Projects I use to pass more dynamic and VI classes.
    In the attached file - an example of my project:
    In the main folder is a folder UpperClass, it is the parent class and child classes and HeirClass.lvclass Heir2Class.lvclass are organized into folders respectively Plugin1 and Plugin2, and these Classes inherit from the parent one and the same WI - UpperClassTest.vi. Plus, this Plugin1 has two, independent from the others, but related classes. A block diagram for an object placed Core.vi UpperClass.
    So, here, if you take EXE, making llb files and run them from start VI for each of the Plugin, then everything works OK.
    But as soon as I on the block diagram of a Plugin will put any object UpperClass, or one of its nasalednikov, there arises a familiar ERROR 1003. Prompt, plc, margasan I get rid of it in this case?
    Attachments:
    Example.zip ‏1481 KB

  • Error 8 occurred at Invoke Node in AB_EXE.lvc​lass:Build​.vi- AB_En​gine_Build​.vi- AB_Bu​ild_Invoke​.vi- AB_Bu​ild_Invoke​.vi.ProxyC​aller

    Hi there,
    Hope someone can help me.  I recently upgraded to LV 8.5 and am having a problem building a .exe which has a subvi in it that opens in a new dialog window.  When I try to build this I get the following error:
    Error 8 occurred at Invoke Node in AB_EXE.lvclass:Build.vi->AB_Engine_Build.vi->AB_Bu​ild_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller
    Possible reason(s):
    LabVIEW:  File permission error. You do not have the correct permissions for the file.
    =========================
    NI-488:  DMA hardware error detected.
    Method Name: Build:Application
    I have built the .exe with the same subVi but without opening it in a dialog window and it works fine., so the problem seems to be linked to the inclusion of the dialog window.
    Any advice greatly appreciated
    Regards
    Tadhg

    UPDATe:  I can get the .exe to build but now I get an error when I run teh .exe which is shown in the picture attached.
    Attachments:
    error screen1.JPG ‏122 KB

  • Error 8 occurred at Invoke Node in AB_EXE.lvclass:Build.vi- AB_Build.lvclass:Bui

    During software build to make exe file, I got the following error message:
    Error 8 occurred at Invoke Node in AB_EXE.lvclass:Build.vi->AB_Build.lvclass:Build_from_Wizard.vi->AB_UI_FRAMEWORK.vi->AB_Item_OnDoProperties.vi->AB_Item_OnDoProperties.vi.ProxyCaller
    Possible reason(s):
    LabVIEW:  File permission error. You do not have the correct permissions for the file.
    =========================
    NI-488:  DMA hardware error detected.
    Method Name: Build:Application
    The vi was working fine before the build. It just access some text files and creates some excel files. No hardware is involved. See if anybody know how to solve this problem. Thanks.

    I am using LabVIEW 2014 and have been getting this error randomly, but fairly consistently on a recent build. I searched all over and could not find a solution that worked. However, just through trial and error I discovered that the problem is related to SSE2 Optimization in the Advanced properties window. I can consistently cause this error by enabling this feature and consistently compile successfully when it is disabled. Try turning this feature off and see if it solves the problem.
    ...UPDATE: After closing and re-opening LabVIEW this error came back, and did not seem to be affected by the SSE2 option. Not that it isn't related, but perhaps not the silver bullet I thought it was.
    I also got the error to go away sometimes when I compiled the EXE while the main program VI was open, whereas it gave the error most of the time when no VIs were open...again, nothing seems to consistently solve the problem...there is definitely some kind of bug in the appllication builder, and it seems like there are a lot of people that have been struggling with this for a long time (as far back as LV 8)...hopefully NI eventually finds this bug and squashes it!..although, I doubt that anybody at NI is even looking for it...

  • Error 7 occurred at Invoke Node in AB_EXE.lvclass

    I get the "Error 7 occurred at Invoke Node in AB_EXE.lvclass" error when trying to build an executable in Labview 8.5.1.  I can run the application without any errors but when I try to build the executable, I get the error.  I have tried a mass compile of the project, tried ctrl + shift + run on the top level vi, and tried to mass compile the folder where the project is located and nothing seems to help. I have also looked at the project dependencies for conflicts and found none.  I have made a new project and tried to build an executable from this same code without any luck.  How can I get this to build an executable?
    The exact error is:
    Error 7 occurred at Invoke Node in AB_EXE.lvclass:Build.vi->AB_Engine_Build.vi->AB_Build_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller
    Possible reason(s):
    LabVIEW:  File not found. The file might have been moved or deleted, or the file path might be incorrectly formatted for the operating system. For example, use \ as path separators on Windows, : on Mac OS, and / on Linux. Verify that the path is correct using the command prompt or file explorer.
    =========================
    NI-488:  Nonexistent GPIB interface.
    Method Name: Build:Application

    Are you using the Report Generation Toolkit?  A lot of error 7's during builds seem to be related to this toolkit.  Any dynamically called VI's?
    Take a look here and here.
    Also search the forums for "error 7" and you'll find some other threads related to error 7 and the application builder.

  • Error 7 occurred at Invoke Node in Dist read linkages.v​i- Dist Cmp Settings to Disk Hier.vi- B​uild Applicatio​n.vi

    Error 7 occurred at Invoke Node in Dist read linkages.vi->Dist Cmp Settings to Disk Hier.vi->Build Application.vi????
    Hi I do not understand how to resolve this nagging problem.
    I run the program in the development time and it all goes smoothly.
    However when i wanted to build the program. I often run into this problem.
    How to resolve it?
    Clement

    Hey Clement,
    Which version of LabVIEW are you using? There some knowledgebases out there that address the issue. Click here for the first KB or here for the second one. Hopefully these would help.
    Regards,
    Chetan K
    Application Engineer
    National Instruments

Maybe you are looking for

  • Help needed in query optimization.....

    Hi I have this below query which automatically gets generated in siebel. Problem is when i execute this query in toad for "Nichole" it took 2 mins to return 30 records but when i execute this same query for "Adam" it returns more records than Nichole

  • First name and last name order in contact list

    Actually, my contact list is displayed with the last name before the first name, but everything is fine in Address Book settings (I choosed "First name, Last name" option), and I checked that first name and last name has not been reversed for some re

  • QT video in Full Screen mode

    Dear friends, my web www.aproduction.com.ua 1. How I can play QT video in Full Screen mode (MAC & PC)? 2. How I can set some attention info for visitors that I use QT video and for playback they should click on video & press space. Some popup or what

  • Problem with field divided on two pages

    Hello to all. On paper design view the last field on first page continue on the second page. Problem is that field not continue at the begining of the page but much lower. Anyone know where or what is the problem? Thanks.

  • Component and Panels - newbie

    sometimes panels are directly added and sometimes a Component is created and panels are added to Component and then they are used in JSplitPane. In what kind of situations can we add directly the panel, and when do we need the Component() ? eg final