Error 1073807302 while connecting a third party USB device,and showing invalid setup

While connecting a third party USB device,In NI MAX it is showing error 1073807302,Unable to start operation because setup is invalid,and error 1073807246 Object Reference is Uninitialized,in the USB settings Tab it is showing no pipe present in Bulk in pipe and in VIEW ATTRIBUTE Tab it is showing invalid property....
please kindly reply me.....!!!

sir,without configuring in NI-MAX how can we open a connection to VISA.
If i install the device driver provided by supplier,i am not able to view my device in NI-MAX,so that, I had created and installed .inf file for my device using VISA driver wizard, In NI-MAX now I can see my device and its properties in visa interactive control.But it was showing some errors(Error-1073676418,error-1073807302,error-1073807298),in the USB settings Tab it is showing, "No pipe present in Bulk In-pipe", and in VIEW ATTRIBUTE Tab it is showing invalid property.In program it is showing error 1073807302,Unable to start operation because setup is invalid,and error 1073807246 Object Reference is Uninitialized,
While Searching in ni.com, some one posted that change the USB Alternate settings to 1/2/3,default value is 0,but now also my problem is not solved.
I am using VIATOR USB HART modem, Model 010031.

Similar Messages

Third party USB products and the Airport Extreme

If I hook up a USB splitter to my Western Digital hard drive, then plug one USB into my Airport extreme and the other in my XBOX 360 will my files on my hard drive become available wirelessly for use on my computer and also be available to be retrieved wired to my 360?

You do not want to do that. You can't connect two computers (the Xbox and AEBS) to the same USB bus. Not only won't it work but you may damage one or both (the Xbox and AEBS).

Third party USB products and Airport Express

If I hook up a USB splitter to my Western Digital hard drive, then plug one USB into my Airport express and the other in my XBOX 360 will my files on my hard drive become available wirelessly for use on my computer and also be available to be retrieved wired to my 360?

No. The AirPort Express (AX) does not support USB hard drives.
The second thing is that you can't connect two computers (the Xbox and AX) to the same USB bus.

Third party USB cable detected by IOS 7 update

Yesterday I had a working Ipad2 and foolishly I allowed it to update itself. Big mistake!
After all sorts of hangs, reboots etc I got it working again and then watched the battery drain before my eyes. Charged it overnight and after 12 hours it was at 75% and just about holding at that level. I have a third party USB cable and I borrowed my daughters OEM cable. When I plugged that in I could immediately see that it was charging normally BUT it also immediately disabled rotation and it is now stuck in landscape mode. I've tried switching the lock button to "Lock Rotation" and I see the icon on screen changing from locked to unlocked but it will not rotate. WHAT THE..............
Detecting that I am using a cable purchased from another source and deliberately disabling my property without my authority borders on the criminal.
Apple need to get it sorted.

I'm sure Apple would love for you (and everyone else) to use their cables...that's a given. But I seriously doubt that any kind of intentional "crippling" would be done to anyone's unit in some way because they used a third-party cable. Seems like the way it's setup now, if a third-party cable is detected, you'll get an on-screen message that the cable is detected as such and you may have issues when using it.
Try the cable again and if it faults the rotation function in the same way, then you can decide if you want to continue using the cable if it is indeed causing this same fault consistently. Otherwise, it could have just been a coincidence.

MacBook Pro with Third Party USB External Modem ? Drivers? Network Pane?

I bought my brother a MacBook Pro last month, and he is using it fine in Pakistan with my Airport base station and cable internet access. Problem is when he is on the road, and using GPRS with his Sony Ericsson P900/910 is terribly expensive there. So, I have to send him an Apple USB modem (that I am yet to hear good things about). However, he does have an external third party USB modem that works fine with PC laptops. Are there any generic drivers for USB modems built into OS X in MacBooks? How would he go about using the external USB modem in Network control panel and using a generic driver?
Is there a way to use Parallels (that he has) to connect to Internet from the Windoze USB modem and have MacOS X use the Windows connection as the "router"? Thanks.
Imran

No answer received. Closing to reduce clutter.

How to connect to third party using PI for outbound and inbound interfaces

Hello,
I have scenarios where I have data coming in from third party EDI subsystem and sent to SAP. And also from SAP to EDI subsystem. We need to send the XMLs to the EDI subsystema nd also receive XMLs.
Can someone please suggest the ways I can connect to EDI subsytem for both Outbound and Inbound interfaces.
Thanks

Hi Prabhu,
EDI file is different from the normal flat or xml file. Hope you understand the difference.
Now if your EDI subsytem has the capability of converting the xml file to edi file viceversa then create and receive the xml file from the EDI subsystem. For the xml file you may use the file adapter as an option.
If it doesnot have the capability then seeburger adapter needs to be used. This is not an inbuilt adapter. So your company needs to purchase it.
Regards,
---Satish

Installed latest version of iTunes, now I cannot play music through my Airport express. I'm seeing the message "An error occurred while connecting to the AirPlay device "living room". The network connection failed.

Installed latest version of iTunes, now I cannot play music through my Airport Express. I'm seeing the message "An error occurred while connecting to the AirPlay device "living room". The network connection failed..."Living room" is what I named the is what I named The AirPlay function of the Aport Express. Thanks!

I have the same problem - did you solve it?

"An error occurred while connecting to the AirPlay device "Living Room Apple TV". An unknown error occurred (406)."

This error message keeps popping up overtime I try to play an iTunes bought tv show from my mac book pro to my apple tv "An error occurred while connecting to the AirPlay device “Living Room Apple TV”. An unknown error occurred (406)."
Does anyone know what this means and how to fix it. Both devices are registered on the same apple id and password. This problem just started happening within the last week or so but prior to that everything was working as it should have. In fact since the launch of icloud things have been glitchy for me with purchasing and playing off the apple tv as well.
Can someone please help?'
Thanks

Unfortunately Apple's error codes are very much a mystery (at least to me), try restarting the Apple TV, iPad and router. If that doesn't help look into whether you might be encountering interference on your network.
Intermittent problems are often a result of interference. Interference can be caused by other networks in the neighbourhood or from household electrical items.
You can download and install iStumbler (NetStumbler for windows users) to help you see which channels are used by neighbouring networks so that you can avoid them, but iStumbler will not see household items.
Refer to your router manual for instructions on changing your wifi channel.

An error occurred while connecting to the AirPlay device "Apple TV". An unknown error occurred (-15000).

Hi ,
I acquired an Apple TV (Gen3) a couple of days ago.
The Apple TV seems to be connected properly to WIFI (Good signal)
I watched streaming videos on Youtube and film trailers – the speed is ok.
I followed the protocol but, still, I cannot connect Itunes to the Apple tv.
These are the error messages:
On the TV : apple tv could not connect to library
In Itunes: An error occurred while connecting to the AirPlay device “Apple TV”. An unknown error occurred (-15000).
Please note that Apple TV doesn’t appear in the list of devices in Itune’s preferences menu.
The Home Share is enabled on both devices and I connected with the Same Apple ID on each device.
Airplay is on.
Ref Apple TV :
Apple tv: Model MD199HC/A
Serial number DY******RHN
apple tv software : 5.3(6105)
Imac: OS X version 10.8.4
I already tried to :
Unplug/plug modem and router
Test connectivity
Disable the Firewall
Re-enable the firewall with Itunes in the list of ‘allowed’ devices
Re-set Apple TV (3 times) + Up to date
Re-start Apple TV and computer several time
Itunes is up to date
Could you please help?
Many Thanks
Sylvie
<Edited By Host>

Hi all,
Thanks for your comments.
In my knowledge, there isn't any security software active on my computer.
After re-setting my routeur several times, I finally swapped it against an Airport Time Capsule.
It solved the problem, however, I would be interested to know if a (less expensive) solution exists.
Sylvie

Third-Party USB to Ethernet Adapter not working since 10.8 updated

Hi I have a third-party USB to Ethernet adapter. Since the update of mountain lion the adapter does not work.
Is there a driver or something I can do to make it work?
Thanks

USB not so good, this very good.
Thunderbolt to Gigabit Ethernet Adapter

I had itunes played from my PC to my music system that is connected through a nework. It use to work fine, but now I get an error message that say "An error occured while connecting to the Airplay Device "Stereo". An unknown error occured (-15000)".

When trying to play itunes from my PC to my stereo connected to an Airport Express, I gen an error that says "An error occured while connecting to the Airplay device "Stereo" an unknown error occured (-15000)". This has happened before and for reasons unknown to me, the problem corrects itself, then it starts again/ Makes me wish I did not have my music on itunes.

moehadi, Welcome to the discussion area!
This is typically caused by a firewall or Internet security software running on your PC. Please read the comments in "Error -3256 or -15000 when streaming to AirPort Express base stations using iTunes".
Also there is "iTunes 8: Unknown error -15000 when attempting to stream music to devices connected to AirPort Express with AirTunes".

Error occured while connecting to FTP Server...

Hi,
I am trying to use the file adapter to pick the file from FTP server however file adapter raised the following error:
Error occurred while connecting to the FTP server \"64.72.230.42:21\": java.net.ConnectException: Connection timed out: connect
I changed the timeout of the communication channel to 1200 but still getting this error after a minute.
The ftp server is working fine with my ftp client.
Could you please help me to fix this issue ?

I got the following message
"Processing finished successfully" when the ftp folder did not have the required file.
Do you mean, the connection is ok when there is no file in the source directory.
Yes.
However as soon as i put the file start getting the same error message.
This could be then an authorization issue. Check if your source dir & file are having proper authorizations. Check with your BASIS guy.
I set the source directory to a folder name which does not exit on ftp server. now i am getting "The FTP server returned the following error message: 'com.sap.aii.adapter.file.ftp.FTPEx: 550 /user038888888888888888/input: The system cannot find the path specified:"
So, do you think it is a problem of authorizations ? and if it is then how can i change it ? should i have to change the permissions of the folder on ftp server?
Thanks for your support. I really appreciate your help. I almost spend a whole day trying to fix this issue.
Regards,
Ehsaan.

CRS 5 Backups fail with this error: Unknown error occured while connecting to the host

Dear All,
We have backup issue with UCCX 5.0(2)SR03_Build317, while trying to take backup giving following error "Unknown error occurred while connecting to the host".
I have found the solution in the Cisco and tried all the suggestion, still not working and same error observed. Due to backup issue we unable to do any changes on the CRS, when we try to create new agents, those agents are not reflecting in the CRS.
Also I have observed bellow error , when try to re-sync the JTAPI,
Error while handling the input   request.
Top of Form
Config Changes are not allowed during 'Backup' operation, which   was started by 'Scheduler' at 'Fri Jun 08 18:00:03 GMT+08:00 2012 '. Please   try again after 'Backup' is complete.
Bottom of Form
http://www.cisco.com/en/US/products/sw/custcosw/ps1846/products_tech_note09186a00809a752c.shtml
Solution
Complete these steps in order to resolve this issue:
•1.      Access the UCCX server and navigate to Start > Run, and type CET.
•2.      When the warning message appears, click NO.
•3.      Choose com.cisco.crs.cluster.config.ArchiveAdminConfig.
•4.      On the right side, double-click the record ID.
•5.      Click the com.cisco.crs.cluster.config.ArchiveAdminConfig tab, and clear the password under Backup Storage.
•6.      Click Apply.
•7.      Navigate to Appadmin > Tools > Backup and Restore.
•8.      Under Backup Storage Location, type the new password, and click Update.
After you complete these steps, you can run the backup. If the backup fails, restart the server, and try the backup again. If the backup still fails, you can navigate to CET, clear all the fields, and then type the new information for the storage location.
Please help me with your suggestions.
Thanks & Regards,
Naveen .S

Please any one help me on this issue..

Image Ultra Builder 4.0: "An error occurred while connecting to server: Check the server"

Ladies & gentlemen
I am using evaluation version of ImageUltra Builder 4.0 for Windows
XP. Both server and console have been installed on the same machine.
When I try to add a new repository, then after pressing the final
"Finish" button I get the message "An error occurred while
connecting to server: Check the server".
This message appears when the service IUServer runs.
I have not found any mention of this error neither in the Internet nor
in the documentation. Can any one suggest what could have been done wrong?
Thanks, Ilya Druker

I've had the same problem when trying to generate a database on an external storage unit. When I create a new repository there are two option:
1) Location: - This is the location where you want to store the files itself. This server does not have to have a database running on it
2) Server: - This is the name of the server that actually runs the DB2 database that keeps track of the repositories. This server does not have to be the same as the location where you store the files. This could also be the IP address of the server, not necessarily the name.
The documentation for this is somewhat confusing, but the above stuff works atleast. I have tried in never versions than 4.0 as well.

BIB-16613 Database access error occurred while connecting to the OLAP insta

I am trying to connect to the database using the BI Beans sample bootstrap.jpr
I am getting the BIB-16613 error.
oracle.dss.security.BISecurityException: BIB-16613 Database access error occurred while connecting to the OLAP instance.
java.sql.SQLException: Io exception: The Network Adapter could not establish the connection
The bi_checkconfig utility gives me:
C:\utils\JDev903\bibeans\bin>bi_checkconfig -h pavelr -po 1521 -sid LOCAL -u BIBDEMO -p BIBDEMO
BI Beans Diagnostics(v1.0.0.0) 17/03/03
===============================================================================
JDEV_ORACLE_HOME ............................. = C:\utils\JDev903
JAVA_HOME .................................... = C:\OraHome1\jdk
JDeveloper version ........................... = 9.0.3.1035 (Production)
BI Beans version ............................. = 9.0.3.4.0
BI Beans internal version .................... = 2.7.0.11.3
Connect to database .......................... = Successful
JDBC driver version .......................... = 9.2.0.1.0
JDBC JAR file location ....................... = C:\utils\JDev903\jdbc\lib
Database version ............................. = 9.2.0.2.1
OLAP Catalog version ......................... = N/A
OLAP AW Engine version ....................... = N/A
OLAP API Server version ...................... = N/A
BI Beans Catalog version ..................... = N/A; not installed in BIBDEMO
OLAP API JAR file version .................... = 9.2
OLAP API JAR file location ................... = C:\utils\JDev903\jdev\lib\ext
Load OLAP API metadata ....................... = Successful
Number of metadata folders ................... = 3
Number of metadata measures .................. = 26
Number of metadata dimensions ................ = 22
Metadata output location ..................... = C:\utils\JDev903\bibeans\bin\bi_metadata.txt
I can connect to OLAP BIBDEMO (and SH) schema using OEM.
I can connect to BIBDEMO from JDev Connections (Catalog connection to BIBCAT, OLAP connection to BIBDEMO).
How can I establish the connection from the bootstrap sample?
Pavel

Please try follow the steps under "Installing and Configuring the Samples "http://otn.oracle.com/products/bib/htdocs/samples/installing_samples.html - the section titled "Update the samples project settings".

Error 1073807302 while connecting a third party USB device,and showing invalid setup

Similar Messages

Maybe you are looking for