Error -1073807343 occurred at niDCPower Initialize With Channels.vi

Hi all,
While initializing NI PXI-4130 power source I got the error "Error -1073807343 occurred at niDCPower Initialize With Channels.vi".
The routine is in a sub VI already working since two years.
No problem accessing the supply with NI-DCPower Soft Front Panel.
I have the problem since Thursday after installing some LabVIEW updates (don't remember which ones, just all the available).
Is this problem known?
Can anybody help me?
BR
ViP

Dear vigna,
I would please you to check the advices in this KB:
http://digital.ni.com/public.nsf/allkb/8130049893D6461E86256F3B00461E1B?OpenDocument
When the Error still occurs please let me know.
Kind Regards,
Oleg Scherling, M.Eng | Applications Engineering | National Instruments | NIG |

Similar Messages

Error -1074135038 occurred at IviScope Initialize With Options.vi

Hello,
I'm new to LabView and to IVI drivers, and I'm having problem connecting to a LeCroy LT344 oscilloscope.
I have LabView 12.0, MAX 5.3 and the lctlxxxx IVI driver installed. I already configured the driver, and I can use the VISA test panel to communicate with the scope. However, when I try to run the IviScope - Acq Wfm Edge Triggered.vi example (after choosing the IVI Logical name), it gets stucked in the IviScope Initialize.vi block, and generates the following error:
Error -1074135038 occurred at IviScope Initialize With Options.vi
Possible reason(s):
Primary Error: (Hex 0xBFFA0002) File could not be opened.
Complete call chain:
IviScope Initialize With Options.vi
IviScope Initialize.vi
IviScope [CA] - Cont Acq Wfm Edge Triggered.vi
I really appreciate any help on the matter.
Thank you,
Vinícius

Hi,
I think is a double Post?
http://forums.ni.com/t5/LabVIEW/Error-at-IviScope-Initialize-using-lctlxxxx-driver/m-p/2123946
Are you trying to use the NI-Scope to control your Hardware?
IviScope vs. niScope Hierarchy
http://forums.ni.com/t5/Instrument-Control-GPIB-Serial/IviScope-vs-niScope-Hierarchy/td-p/1830727
Ni-Scope:NI-SCOPE 3.9.4 - Windows Server 2008 R2 64-bit/Server 2003 R2 32-bit/7/Vista/XP 32-bit
http://joule.ni.com/nidu/cds/view/p/id/3195/lang/en
Which IVI Class did you install or your hardware use?
I found something about IVI 1.4 Class. I'm not sure if it helps
http://www.ivifoundation.org/downloads/Class%20Specifications/IVI-4.1_Scope_2011-02-14.pdf
Best Regards.
Kais Mekacher
AE Germany-Munich
Kais Mekacher
Applications Engineer
Germany - Munich

Error -1074126826 occurred at niSwitch Initialize.vi

I'm getting an intermittant error with my switch card:
Error -1074126826 occurred at niSwitch Initialize.vi
Possible reason(s):
Max time exceeded.
Device: SWT1-DUTSwitching
Status Code: -200221
It happens about 25% of the start-ups (fixed with a restart). I can't find the error codes in any documentation - has anyone got any ideas please?
Copyright © 2004-2015 Christopher G. Relf. Some Rights Reserved. This posting is licensed under a Creative Commons Attribution 2.5 License.

G'Day Chad - thanks for your answer: after several weeks of testing I haven't had the error message since I upgraded to 3.3.1! Well done
Copyright © 2004-2015 Christopher G. Relf. Some Rights Reserved. This posting is licensed under a Creative Commons Attribution 2.5 License.

Error -1074118653 occurred at niRFSA Initialize.vi

I am currently using NI PXI-1045 to test RF signal from a device under test. I am using an exact copy of an example used for NI-RFSA. The unit under test is connected to the input of Ni PXI-5600 which is wired with Ni PXI-5142 to create NI-PXI-5661. When I run my vi, I got the following message " Error -1074118653 occurred at niRFSA Initialize.vi
Possible reason(s):
The device specified is not supported by this driver.
Status Code:-223543"
Would you please help?
Regards,
Jean-Richard
JR
Solved!
Go to Solution.
Attachments:
RFSA_testing_RF_output.vi ‏18 KB

OK, then open Measurement and Automation Explorer(MAX). It sounds like you need to associate the downconverter with the digitizer. On the left side of MAX expand the devices and interfaces tree and then expand the chassis tree. Right click on the 5600 device (slot 8) and select properties and associate it with your digitizer.
Using LabVIEW 2010SP1 and TestStand 4.5

Error An unexpected error has occurred. Troubleshoot issues with Microsoft SharePoint Foundation. Correlation ID: 65ef1cb8-1cbf-40ee-b79b-05db15ca6dbb

Hi,
Since I installed a few updates, that I can't access the sharepoint the same way. I always get errors when trying to access the majority of the pages.
I already removed the update suggested on other threads (KB2844286), but everything remains the same.
I always receive errors like this one:
Error
An unexpected error has occurred.
Troubleshoot issues with Microsoft SharePoint Foundation.
Correlation ID: 65ef1cb8-1cbf-40ee-b79b-05db15ca6dbb
what can I do? The Sharepoint 2010 is located on a virtual partition of our server, running Windows Server 2008 Standard edition SP1.
When I try to access administration tools it happens the same error, and I don't know what I can do more.
Please help me.
best regards,
Jorge Guimarães

I followed some tips, to trace the error, allowing some trace debug, and got this:
Server Error in '/' Application.
Object reference not set to an instance of an object.
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.NullReferenceException: Object reference not set to an instance of an object.
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[NullReferenceException: Object reference not set to an instance of an object.]
Microsoft.Office.Server.Administration.UserProfileApplicationProxy.get_ApplicationProperties() +134
Microsoft.Office.Server.Administration.UserProfileApplicationProxy.get_PartitionIDs() +44
Microsoft.Office.Server.Administration.UserProfileApplicationProxy.IsAvailable(SPServiceContext serviceContext) +329
Microsoft.Office.Server.WebControls.MyLinksRibbon.get_PortalAvailable() +44
Microsoft.Office.Server.WebControls.MyLinksRibbon.EnsureMySiteUrls() +60
Microsoft.Office.Server.WebControls.MyLinksRibbon.get_PortalMySiteUrlAvailable() +15
Microsoft.Office.Server.WebControls.MyLinksRibbon.OnLoad(EventArgs e) +91
System.Web.UI.Control.LoadRecursive() +65
System.Web.UI.Control.LoadRecursive() +190
System.Web.UI.Control.LoadRecursive() +190
System.Web.UI.Control.LoadRecursive() +190
System.Web.UI.Control.LoadRecursive() +190
System.Web.UI.Control.LoadRecursive() +190
System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +2427
Version Information: Microsoft .NET Framework Version:2.0.50727.5477; ASP.NET Version:2.0.50727.5479

An error has occurred because a control with id '%spPlaceHolderMain%' could not be located or a different control is assigned to the same ID after postback.

Hello All, When i try to do a filter on an entity and click filter button, i see the below error message being popped up. Can someone provide a solution to this ?
"An error has occurred because a control with id '%spPlaceHolderMain%' could not be located or a different control is assigned to the same ID after postback. If the ID is not assigned, explicitly set the ID property of controls that raise postback events
to avoid this error."
Please let me know the process to set the ID explicitly.

Can you try resetting the IIS?

Sync Error "An error has occurred please try again" with Contacts using Desktop Manager

Hello,
I've been trying to fix my Boss's sync issue for sometime. I hope some one can help.
He has a BB Curve
He uses Microsoft Entourage 2008 sync'd with Mac's Address Book
His desktop manager is up to date
When syncing contacts he gets "An error has occurred please try again"
I went under advanced settings and click replace everything on blackberry device. That worked and his phone is now up to date with his address book however if you don't click "Replace.." the error still occurs.
He fusterated because he wants to be able to sync back and forth not just from his computer to his phone. I hope this all makes sense and someone can help.
Thank you

demzi11 wrote:
I have the same thing! I have no idea how to fix it
Hi and Welcome to the Forums!
Read the KB that Xandrex linked...it cures this situation in something like 75% of the time.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

ERROR in NI VI -- "niSwitch Initialize With Options.vi"

Apparently there is an error in the niSwitch Initialize With Options.vi supplied with my PXI 2503 switch board. I know there are new version of niSwitch, but I am using an older one with file dates of 6/29/2000. The bug is that the "IVI New Session" sub vi input terminal "resource name" is incorrectly wired to the call library node "option string" output terminal. The correct source for the "resource name" input is the "resource name" output terminl of the call library function. If you make this change the VI seems to work. Can anyone else with the old NI switch software verify this issue?

Good morning brent2004,
Thanks for contacting National Instruments with your issue, we'll try our best to resolve it for you as quickly and efficiently as possible.
I have searched in our Corrective Action Database, and have verified that NI-Switch 2.0 did have an issue with the niSwitch Initialize With Options.vi and the logical resource name. This is an extremely old driver that you're working with, and since the upgrade is free, I highly recommend it for your project.
Sincerely,
Minh Tran
Applications Engineering
National Instruments

An Error has occured when trasfering file with R/3 order

Hi Guys,
Could you please help me on this.
when saving the order in CRM my i got this error..when i go into error details.
"Inconsistent update flags (Notification E C( 004)"
what needs to be done to slove this error.
what are the possible reasons for thsease.
Thanks in advance,
Regards,
Shaik

Hi Shaik,
Please check the following notes. This will be of helpful.
1056966 C( 004: Inconsistent update flags
1125147 C( 004: Inconsistent update flags
1044818 BDOC status is 'yellow' - What should I do?
718044 Composite SAP Note 'Inconsistent update flags'
Thanks
Abishek

"agesani Initialize With Options" timeout error on HP E4401B spectrum analyzer

System: Windows XP Pro, LabVIEW 7.1, IVI Compliance Package 3.0, NI-VISA 4.1
I have an HP E4401B Spectrum Analyzer. I'm trying to write some LabVIEW code for it, using the agesani.llb library.
When I try using the agesani Initialize With Options VI, I get the following error:
Error code: BFFF0015
Source: agesani Initialize WIth Options.vi<ERR>Driver Status: (Hex 0xBFFF0015) Primary Error: (Hex 0xBFFF0015) Timeout expired before operation completed.
I've searched the NI Knowlege Base, and haven't found anything that seems useful. What I _have_ found are the following items.
Knowlege Base article "Time-Out Error with the Agesa Instrument Driver Example". This refers to the agesa drivers, not the agesani drivers. It also references an E4440A spectrum analyzer, not an E4401B. The article says one cause could be that a compatibility mode other that SCPI is in use. While the articles says how to fix this on an E4440A, the fix does not appear to apply to the E4401B. In fact, if it is even _possible_ to have a mode other than SCPI on an E4401B, I can't figure out how to do it. A second possibility the article suggests is that the spectrum analyzer is in Phase Noise mode rather than Spectrum Analyzer mode. My E4401B is in SA (spectrum analyzer) mode. I don't even see a way to put it in any other mode - I don't think the required options are installed. Finally, my VI is configured as the article states - ID Query YES, Reset Device YES, etc. I should note that the instrument's GPIB address is 18, and that this matches the resource name GPIO0::18::INSTR.
Some additional information: The spectrum analyzer's screen is indicating the instrument is in Remote (R) mode as a Talker (T). A "Query UNTERMINATED" error message appears at the bottom of the instrument screen.
I've attached the results of a NI Spy capture to this message. (At least, I think I have. I've never tried doing this before, so if it doesn't show up, would some kind soul tell me how to include an attachment to my post?)
Oh, yes. The agesani version is driver version 1.1, updated 17 Aug 2007. (The version that's currently on the NI download site.)
Attachments:
Capture4.spy ‏9 KB

Hi MXI Master,
If there's an instrument timeout, I haven't been able to find it yet. Seems like there should be, so maybe I just haven't looked in the right place yet. As for the timeout value on the computer, I'm not sure what you mean by this - could you elaborate, and maybe tell me where to find it?
As far as SCPI mode, if it's possible to put the E4401B in something _other_ than SCPI mode, I haven't figured out how. I can't find any support in the programming manual for anything other than SCPI.
That kind of seques into my next couple points. The NI Spy output indicates that one of the commands that is being sent is "*SRE 32".
The "User's & Programmer's Reference" for the E4401B says (on page 206) "Send the *SRE <number> command (where <number> is the sum of the decimal values of the bits you want to enable plus the decimal value of bit 6). [Bit 6 is the Request Service (RQS) Summary Bit. BP] For example, assume that you want to enable bit 7 so that whenever the operation status summary bit is set to 1, it will trigger a service request. Send the *SRE 192 (128 + 64) command."
This statement would seem to imply that the "*SRE 32" command that is being sent by the agesani "Initialize With Options" command is an illegal command, or at best an ineffective command. In light of that, it is interesting to me that the NI Spy output indicates that the next line , viQuery(GPIB::18::INSTR (0x246E9C8), "%s?","%ld"), is generating an 0xBFFF0015 error. In addition, I can find neither the "%s?" nor the "%ld" commands listed in the Programmer's Reference. I wonder if these could be for a firmware revision later than mine (A.01.03), or for instrument options I don't have (A4H, A4J). Alternatively, I wonder if these are simply mistakes.
The next line in the NI Spy output, Formatted viWrite(CPIB0::18::INSTR (0x0246E9C89),"INST:NSEL?",11,11), also puzzles me. The Programmer's Reference indicates that this is a supported command, to see what instrument application is currently selected. (e.g. spectrum analyzer, GSM, Bluetooth, EDGE, noise figure, etc.) However, when I try to issue this command to my instrument, by using the Instrument I/O Assistant Express VI, I get an "Undefined header" error on the instrument's front panel. The instrument's error history shows the same "Undefined header" error. Since my instrument only has the basic spectrum analyzer option installed, I wonder if this command is not valid? (Personally, I wouldn't write instrument firmware code this way, but who knows?) Alternatively, I wonder if this command requires a firmware revision more recent than mine. (The Programmer's Reference is silent about this possibility.)
The next line in the NI Spy output, Formatted viRead(GPIB::18::INSTR (0x0246E9C8),"",4000,0), has another 0XBFFF0015 error associated with it.
Does this information shed any more light on the situation?

Configure Synchronization Connections An error has occurred while accessing the SQL Server database

Hi,
i am getting following error message
Central Administration --> Synchronization Connections
An error has occurred while accessing the SQL Server database or the SharePoint Server Search service.
If this is the first time you have seen this message, try again later. If this problem persists, contact your administrator.
Central Administration --> Manage Profile Service: User Profile Service Application --> Manage User Properties
Error
An unexpected error has occurred.
Troubleshoot issues with Microsoft SharePoint Foundation.
Correlation ID: 3bce5a11-f2dc-4788
Please tell how to fix it.
iffi

Event ID 5555 -> i have change the Timer jobs recycling time AM to PM
for User profile page not display number of count in the page first check services , connection ,
IISRESET /NOFORCE / timer services restart
Deepesh Yevle MCTS

Occasional GPIB Error -1073807342/-1073807300

Hi
I am running a test with a CSA7404B (Tektronix Communication Sigal Analyzer). The system is expected to run for about 7-8 days without interrruption while communicating to this instrument. Occasionally (after 48 hours of running without problems), I get the one of the two errors mentioned above. I dont have multiple open visa sessions. Any ideas?
Thanks

Error -1073807342 mostly is caused when the resource name passed to VISA Open is incorrect. Try to adress your device directly such as: GPIB0::5::INSTR. Make sure not changing GPIB adress on your target device ((Tektronix) while communicating with it.
As a precaution for error -1073807300 prove following. Is there really only one session opened ?
If one of both errors occur, try to open a VISA session and communicate with your instrument via MAX (Measurement & Automation Explorer). Further try to reset your remote GPIB device.
How do you procedure when this error occurs ? Do you restart your VI which is responsible for communication ( or LabVIEW completly) ? Do you reset your GPIB device ? Do you restart your PC ?
Is this error dependent on your GPIB device (does this error also occur if you communicate with an other
instrument) ?
What GPIB Card you are using ?
Maybe you can attach your GPIB communication vi realized with VISA VI´s ?

Error while executing Initialize with Data Transfer for 0FI_GL_10

Hello All,
Post Pre prod refresh, our timestamp for the datasource 0FI_GL_10 got reset. Due to which our deltas did not bring any records to the BW system.
First we did an Initialize without data transfer for all the BW related datasources. The deltas were then set properly for all datasources except 0FI_GL_10.
We then raised a message to SAP and they suggested to run the 'Initialize with data transfer' for 0FI_GL_10 so that the timestamp is set and accordingly the deltas are fixed.
The issue now is we are getting the following error message while running INIT with data transfer.
Job terminated in source system --> Request set to red
Message no. RSM078
We have copied the data till July 1st week of 2011.
Please advice. The issue is very critical.
Thanks & Regards
Sneha

Hi Arvind
Thanks for your inputs.
Please find below the details of the short dump.
Runtime Errors         DBIF_RSQL_SQL_ERROR
Exception              CX_SY_OPEN_SQL_DB
Date and Time          09/07/2011 11:25:32
Short text
     SQL error in the database when accessing a table.
What can you do?
     Note which actions and input led to the error.
     For further help in handling the problem, contact your SAP administrator
     You can use the ABAP dump analysis transaction ST22 to view and manage
     termination messages, in particular for long term reference.
How to correct the error
     Database error text........: "ORA-01652: unable to extend temp segment by 128
      in tablespace PSAPTEMP"
     Internal call code.........: "[RSQL/FTCH/FAGLFLEXT ]"
     Please check the entries in the system log (Transaction SM21).
     If the error occures in a non-modified SAP program, you may be able to
     find an interim solution in an SAP Note.
     If you have access to SAP Notes, carry out a search with the following
     keywords:
     "DBIF_RSQL_SQL_ERROR" "CX_SY_OPEN_SQL_DB"
Information on where terminated
    Termination occurred in the ABAP program "GP_GLX_FAGLFLEXT" - in
     "FETCH_TO_ISTRUCTURE".
    The main program was "SBIE0001 ".
    In the source code you have the termination point in line 903
    of the (Include) program "GP_GLX_FAGLFLEXT".
    The program "GP_GLX_FAGLFLEXT" was started as a background job.
    Job Name....... "BIREQU_4N3PZQ12IA0X0PYGEA85IG39S"
    Job Initiator.. "BIWREMOTE"
    Job Number..... 11203300
    The termination is caused because exception "CX_SY_OPEN_SQL_DB" occurred in
    procedure "FETCH_TO_ISTRUCTURE" "(FORM)", but it was neither handled locally
     nor declared
    in the RAISING clause of its signature.
    The procedure is in program "GP_GLX_FAGLFLEXT "; its source code begins in line
    840 of the (Include program "GP_GLX_FAGLFLEXT ".

Error -32810 occurred at The FieldPoint server initialization failed. Possible causes: 1. Missing or corrupt configuration file; 2. Failed to create callbacks. : FP Open.vi

I have two cFP-2120 RT controller. They both have NI-Serial RT2.5.6, DataSocket for LV RT4.2, NI-VISA 3.6, FP Drivers 5.1.0, FP VI Manager 3.1.0 LV RT 7.1.1 installed. But one same vi can run on one controller but not another.
the error message got when it runs on another controller is "Error -32810 occurred at The FieldPoint server initialization failed. Possible causes: 1. Missing or corrupt configuration file; 2. Failed to create callbacks. : FP Open.vi"
I wonder by what it is caused?
Thanks

Hi Matthew,
As mentioned previously, this KnowledgeBase article may be of some help. Also, if your code is being run on an embedded controller and then a network controller (not embedded), you will need to run the program differently. On the embedded controller, you should deploy your VI in a Project Explorer or programmatically (as described here.) However, you do not need to deploy the program to a network controller, but simply run the VI.
I would also suggest creating a new .IAK file. Do you still see the same error? Also, double-check that the software installed on the controller matches the software installed on the host PC. If you have any file paths associated with one FieldPoint controller, ensure that you are changing them to match the second controller.
Please keep us posted on your troubleshooting steps. Have a great day!
Amanda Howard
Americas Services and Support Recruiting Manager
National Instruments

An error occurred during the initialization of the view manager - Web IC

We just upgraded our CRM Dev system from 4.0 to 5.0. We've already done this once on our Sandbox. However, in our Dev environment, I execute CRM_IC. Select my profile and then get an exception.
An error occurred during the initialization of the view manager
An exception has occurred
Exception Class CX_SY_REF_IS_INITIAL
Text: Dereferencing of the NULL reference
Program: CL_BSP_WD_VIEW_MANAGER========CP
Include: CL_BSP_WD_VIEW_MANAGER========CM003
Source Text Row: 86
This is the line of code that the exception occurs. I debugged through, but not sure what the problem is.    It seems like it should have something to do with the runtime profile, but I can't seem to find anything wrong. This problem doesn't happen in the sandbox, but we are on a slightly higher support pack in our Development environment.
    get own initial rep view reference
      INITIAL_REP_VIEW = REPOSITORY->GET_INITIAL_VIEW( ).
Any ideas? I've already search OSS.
Thanks, Cat

Thirumala,
Thank for your reply. I already recompiled CRM_IC. I'm trying to execute the standard Webclient and still getting the error. I also reactivated CRM_IC_DT_REP and CRM_IC_RT_REP, but no luck.   I went to SICF and made sure all the services starting with CRM_IC were activated too. Any other suggestions?
Thanks,
Cat

Error -107380734​3 occurred at niDCPower Initialize With Channels.v​i

Similar Messages

Maybe you are looking for

Error -1073807343 occurred at niDCPower Initialize With Channels.vi