Error 10800 when doing Analogue Output with DAQPad-6070E

I'm trying to test out the Analogue Output from my DAQPad 6070E (Firewire). I'm using the Example vi 'Generate N Updates', but get an error:
Error 1080 occured at AO Control
possible reasons: NI-DAQ LV: The opereation could not complete within the time limit.
This example seems to work fine on a PCI E-series card, But the example claims it should also work fine on the DAQPad 6070E.
It seems to sometimes work ok the first time I try after power cycling the DAQPad.
I've tried updating to the latest version of NI-DAQ, with LabView 7.0, Windows 2000.
If i used the test button from withing MAX, then the DAQPad seem to work fine with continuous output of a sine wave.
Any help much appreciated.
Ke
ven.

This is certainly not a solution, especially if you need a lower output rate/buffer.
I've got the same problem with my DAQPAD 6052E. I traced it down to AO START vi. It appears when the output buffer is less than 1000 and the number of output buffer iterations is set to 1. The error does not appear when in the continuous output mode (number of buffer iterations is "0").  I talked to tech support, and they know about the problem, but they do not offer any solutions, except for using a larger buffer. Simply speaking, it is a bug in the driver, which they haven't fixed yet. Way to go, NI.

Similar Messages

  • Error -200141 when doing buffered events with DAQmx and PCI-6602

    When doing buffered events with DAQmx and PCI-6602 I get error 200141 - Data was overwritten before it could be read by the system.
    This error is generated ONLY with random inputs >200/sec.
    My setup is :
    DAQmxCreateCIVCountEdges(taskhandle,"Dev1/ctr3"....
    DAQmxCG+FGSampClkTiming(taskhandle,"/Dev1/FPI35",...
    DAQmxSetCICountEgdesChan(taskhandlem,"", "/Dev1/80MHZTimeBase")
    DAQmxSetChanAttribute(taskhandlw,",",DAQmx_CI_DataXferMech,DAQmx_Val_DMA,0);
    Can somebody help ?

    i'm getting the same Error-200141, while reading semiperiods. (Meas_Buffered semiperiod continous)
    while loop ex.rate seems to be pulsewidth*no.Samples to read. in my case PW=60ms
    Input buffer size measured with Property node= 10000
    why this error happens?? i cant use any mode other than implicit timing for semi-period measurement right??
    more info: all the ai channels are used ~ 16 differencial.
    i found one solution which is _ reinitializing the whole task if an error occur. is this the right way??
    Kudos always welcome for helpful posts
    Attachments:
    Counter_1_Meas Buffered Semi-Period-Continuous_main_lv09.vi ‏34 KB
    SemiPeriod_Reconnect Counter on Error.vi ‏35 KB

  • Runtime error!  when doing XML output

    Hi,
    I am really stuck with this error...
    When running a script to genarate a XML file I keep getting
    an error. The error looks like it is coming from IE:
    Microsoft Visual C++ Runtime Library
    Runtime Error!
    Program: C:\Program Files\Internet Explorer\IEXPLORE.EXE
    This application has requested the runtime terminate it in an
    unusual way.
    Please contact the application support team for more
    information.
    OK
    The script works and genarates the XML output for small
    requests but I get this error when I try to get it to process
    several thousand rows. I need it to be able to process tens of
    thousands of rows!
    Please can someone point me in the right direction for a
    cause/solution to this.
    I have tried putting the script in a <cftry>
    <cfcatch> tag to get an error report but I still get the
    error and when I click "OK" all instancs of IE close.
    CF7 & IE7 (I also got the error in IE6)
    Regards,
    Chris.

    Actually it also happens when I don't do a network migration. I choose -
    create - and it errored when I choose Current User.
    >>> Kevin VanSchepen<[email protected]> 3/23/2006 9:37 AM >>>
    I get a Visual C++ Runtime error on DesktopDNA.exe (abnormal program
    termination)
    - It happens when I am doing a network migration (with and without
    crossover
    connection)
    - The moment I choose Current User or when I choose next after choosing the
    user in Multiple Users
    - It works on other machines, could it be something to do with the user
    account I am trying to migrate?
    Kevin VanSchepen

  • F-04: give error message when clearing AP items with payment block key(R)

    Hi all,
    Customer wants to prevent payment for AP items with payment block key(BSEG-ZLSPR) .
    I want system giving error message when doing payment clearning with t-code:F-04.
    How can I realize it ?
    Thanks Grus!
    Lynn

    Please configure the following nodes properly:
    Financial Accounting>>Accounts Receivable and Accounts Payable>>Business Transactions>>Outgoing Payments Global Settings>>Payment Block Reasons>>Define Payment Block Reasons & Define Default Values for Payment Block
    For the error message: You may define a validation in OB28 with the help of ABAP consultant

  • I am currently using Lightroom 5.6 and operating on a Mac with OSX Ver 10.9.5. I am receiving an error problem when doing the following -  I am exporting selected photos from a particular Catalogue saved on Drive 1 to a folder created on another Drive whe

    Hi, I am having a little trouble with exporting images to another drive and Catalogue and need some help if anyone can give me some advice
    I am currently using Lightroom 5.6 and operating on a Mac with OSX Ver 10.9.5.
    I am receiving an error problem when doing the following -
    I am exporting selected photos from a particular Catalogue saved on Drive 1 to a folder created on another Drive where a Lightroom Catalogue has been created. In this Catalogue I have arranged for the images once exported to be moved to a different folder - I used the Auto Import process under the File dialogue box.
    When processing the Export I receive an error message for each of the images being exported indicating the following -
    Heading Import Results
    Some import operations were not performed
    Could not move a file to requested location. (1)
    then a description of the image with file name
    Box Save As                                  Box  OK
    If I click the OK button to each image I can then go to the other Catalogue and all images are then transferred to the file as required.
    To click the OK button each time is time consuming, possibly I have missed an action or maybe you can advise an alternative method to save the time in actioning this process.
    Thanks if you can can help out.

    Thank You, but this is a gong show. Why is something that is so important to us all so very, very difficult to do?

  • HT3275 Since updating OS to Mountain Lion from leopard, I get the following error message when trying to backup with time machine on external drive.  Could not complete backup to media share.  The network backup disk does not support the required AFP feat

    Since updating OS to Mountain Lion from leopard, I get the following error message when trying to backup with time machine on external drive.  "Could not complete backup to media share.  The network backup disk does not support the required AFP features."  What are AFP features and how do I get Time Machine to backup to my current external backup?

    This means that your NAS does not support the required encryption. Update your NAS to the latest firmware or ditch it and buy a Time Capsule (they are the most reliable when using TM).

  • Getting error 789 when trying to connect with a PC remotely via VPN

    When we set up the VPN we are getting a Error 789 when trying to connect with a PC. Any suggestions would be appreciated.

    The utilities, provided on the CD, are not required for the PC to access the Internet through the 802.11n AirPort Extreme Base Station (AEBSn). They are only necessary for administering the base station.
    If your PC is currently configured as a DHCP client, it shouldn't have any issues connecting by Ethernet. The AEBSn will assign the appropriate IP addresses required for connectivity to the Internet ... just like it does for wireless clients.

  • Error : Profit Center does not match with Business Area. Message no. ZGLTFI

    Hi Everyone,
    Error occurs when doing inbound PGR. Processed done so far are the following:
    Normal PO created & released.
    Inbound created
    Transfer order created and confirmed.
    When doing PGR via VL32N > click Post Goods Receipt error occurs
    Profit Center does not match with Business Area
    Message no. ZGLTFI0001031
    Checked already in KE53 the Profit Center used was assigned to the Co. Code used in the PO.
    The same Profit Center was maintained in material master.
    The Plant used was assigned to proper division and business area.
    Any other ways to check?
    Btw not only in Inbound PGR the error occurs .. also happened in MIGO and MB1C.
    Tried to do other transaction involing the material, plant and profit center all give the same error.
    Any info shared is much appreciated.
    Thank you.

    this error is not a SAP standard error, it is an own message class (ZGLTFI0001), so it must be issued from a validation or user exit.  Please find the user exit, or talk to FI Team and ask what they check

  • IPhone 5 error 4005 when trying to update with itunes

    iPhone 5 error 4005 when trying to update with itunes

    Hello mjy75, 
    Thank yoj for using Apple Support Communities. 
    The following article covers error 4005 when updating your iPhone.
    iOS: Restore errors 4005, 4013, and 4014 - Apple Support
    Regards,
    Jeff D. 

  • HT1386 I keep getting error [54] when i try syncing with i tunes, what do i do?

    I keep getting error 54 when i try syncing with itunes. what do i do?

    Maybe here:
    http://att.macrumors.com/showthread.php?t=1362080
    Also try Googling for: itunes error 54

  • I got error 3295 when doing software update to 4.3.4 on my iphone4.. can some one tell me how skip this error?? I'm new to apple products..!?

    I got error 3295 when doing software update to 4.3.4 on my iphone4.. can some one tell me how skip this error?? I'm new to apple products..!

    anyone????

  • I am continually getting error -69 when syncing iPad Air with latest iOS and iTunes versions. Any suggestions?

    I am continually getting error -69 when syncing iPad Air with latest iOS and iTunes versions. Any suggestions?

    Try Googling "sync without iTunes".
    There are free alternatives and there are not so free alternatives.
    Btw, to check if AVG is causing the problem, you should uninstall AVG and not just "turn it off".
    Also, can you describe how you go about uninstalling a program? For example, how did you "delete" iTunes?

  • What is error 4002 when trying to sync with Itunes match and how do I fix it?

    What is error 4002 when trying to sync with Itunes match and how do I fix it?

    HI
    Read this How to troubleshoot iTunes Match - Apple Support
    Note specifically holding option ket whilst turning off match.
    Jim

  • Error  " Selected numbers does not agree with transferred"

    Hi,
    While in production support I got a issue saying
    Error  " Selected numbers does not agree with transferred"
    How to solve this.
    Regards
    San Reddy

    Hi,
    This doesnt mean that its a failure.
    I will suggest you to check a few places where you can see the status
    1) SM37 job log (In source system if load is from R/3 or in BW if its a datamart load) (give request name) and it should give you the details about the request. If its active make sure that the job log is getting updated at frequent intervals.
    Also see if there is any 'sysfail' for any datapacket in SM37.
    2) SM66 get the job details (server name PID etc from SM37) and see in SM66 if the job is running or not. (In source system if load is from R/3 or in BW if its a datamart load). See if its accessing/updating some tables or is not doing anything at all.
    3) RSMO see what is available in details tab. It may be in update rules.
    4) ST22 check if any short dump has occured.(In source system if load is from R/3 or in BW if its a datamart load)
    5) SM58 and BD87 for pending tRFCs.
    Once you identify you can rectify the error.
    If all the records are in PSA you can pull it from the PSA to target. Else you may have to pull it again from source infoprovider.
    If its running and if you are able to see it active in SM66 you can wait for some time to let it finish. You can also try SM50 / SM51 to see what is happening in the system level like reading/inserting tables etc.
    If you feel its active and running you can verify by checking if the number of records has increased in the data tables.
    SM21 - Job log can also be helpful.
    In your case its probably because of tRFC issue.
    Check SM58 / BD87 for pending tRFCs.
    Thanks,
    JituK

  • When does iphone5s 1528 with iphone6,2 support china unicom's 4g lte network?

    When does iphone5s 1528 with iphone6,2 support china unicom's 4g lte network? Before I activate the cell phone, I could see the 4g at the left corner on the screen, but once I activated the cell phone, the 4g disappeared and 3g instead. It was a terrible experience. It seems that my phone support 4g but Apple and China Unicom disable the functionality.

    All the information you need is right here: http://www.apple.com/iphone/specs.html
    Notice there is no mention of WiMax.
    It doesn't really matter anyway as Sprint is rolling their WiMax network down for use by MVNOs. Actual Sprint customers will not have access to WiMax at all. It was a failed experiment.

Maybe you are looking for