Error 1311 during LabVIEW installation

I am trying to install LabVIEW, but I am getting this error message:
"Error 1311. Source File Not Found: E:\LVCore\LVCore1.cab. Verify that the file exists and that you can access it"
The .cab file exists in the CD and we have used the same CD for installation in the past without any problems.
Does anyone know about this error message. Response is appreciated.
Thank you.

Troy12,
I've actually seen this problem before and it seems to indicate that the CD or CD drive might be bad or something along those lines. One thing you can try is copying the entire cd contents to your hard drive and running the installation from the hard drive itself. This approach has worked in the past but post again if it doesn't and we can move forward from there.
Best Regards,
Chris C
Applications Engineering
National Instruments
Chris Cilino
National Instruments
LabVIEW Product Marketing Manager
Certified LabVIEW Architect

Similar Messages

WHY DO I GETY ERROR 1311 DURING INSTALLATION OF ADOBE READER

WHY DO I GET ERROR 1311 DURING INSTALLATION OF ADOBE READER

From past report, I found following comments:
1311 error comes when during installation some resources are not accessible. It may have happened that some resources were missing or blocked on users machine. We would need MSI logs to look further into this.
One person was able to fix the problem:
After re-booting and cleaning out temp files, etc., the 3rd try resulted in success! I do not know if this error was a fault within my system or not.
I also found a KB article on Adobe Reader 9: http://helpx.adobe.com/acrobat/kb/error-1311-install-reader-9.html
Not sure what version/OS you have, but I hope it helps.

Error 1722 during LabVIEW installation on Multipoint Server

I am installing LabVIEW 2012 on a Multipoint Server and get multiple Error 1722 errors. Has anyone installed LabVIEW on Multipoint Server? Is there a setting that needs to be changed? or a configuration setting that needs to be set?

Hello Friedmanfr,
Error 1722 seems to be a Windows error message. I did some digging and it seems like this Microsoft KB could be useful to you: http://support.microsoft.com/kb/829359
The KB is for Windows Server 2003, but might be relevant to Multipoint as well. If you can provide more details about your issue, I might be able to help you further.
Do you know at what point in the LabVIEW install, these errors occur?
What are you installing LabVIEW 2012 from? DVD? Downloader?
What steps did you take during your install leading up to the point these errors occur?
With servers, it could be that you have permission or network connection issues. Do you have any information on these configurations?
Wan L
Applications Engineer
National Instruments
http://www.ni.com/support

Error 1311 during installing the premiere 12 from DVD disc

even followed the troubleshooting instruction, changing the installation path to " C:\PSEversion12Installer\ ",
still cannot install?

ipcharles
What document were you using for troubleshooting this 1311 issue?
Could this be it?
http://helpx.adobe.com/photoshop-elements/kb/troubleshoot-installation-photoshop-elements- premiere.html#main_Error_1311__Source_file_not_found
Your edited installation path does not look right. I would question "version" being before 12.
If the above is what you were referring to, did you see at any time
This error can occur if you install from within a folder path that contains double-byte characters, like Japanese or Chinese characters. This error can also occur if you install from a folder path with characters with a high ASCII value, like Greek letters.
Have you read this article?
http://www.wiki-errors.com/err.php?wiki=1311
ATR

Error 1311 occurs during install of NIDAQ 6.9.3

I downloaded NIDAQ 6.9.3 from the NI download site, and followed the directions for installing. Unfortunately, every time I attempted to run the setup.exe, I got an error 1311 "cant find file daqlv61eng.cab".
I downloaded a second time from the NI site the Nidaq693.exe file and started the entire process a second time. However the error 1311 occrued again.
I read in another post that this can happen sometimes from a cd file being copied to a hard drive, but I saw no posts for my particular problem occuring with an Internet download.
I currently have NIDAQ 6.9.2 installed, and I am installing 6.9.3 to see if it eliminates an error I get when I run my VI:
"10401 AI group Config. NI-DAQ LV device is not a NI driver, or d
evice not cinfigured."
I went to devices in measurement and automation explorer and I can see the board there, PCI-MIO-16E-4. I have uninstalled the board several times, and reinstalled and hit F5 in max, but this did not help. Appreciate any help.

Hef,
Perhaps the VI has been modified on the new PC. Let's just try an example VI. What does the VI you are using do? If it uses analog input then try an analog input shipping example. If it uses analog output, then try an analog output shipping example. If you don't get the error with the example, then the error is a result of your program.
Additionally, you may want to run the E-Series Online Diagnostic Utility on your board to determine if it is functioning properly. This online utility just takes a few minutes to run and will generate a report after checking your hardware.
Online E Series Diagnostic Utility
http://www.ni.com/support/selftest/
Regards,
Justin

Error 1311, Source file not found, measurementstudio5.cab

I'm installing Measurement Studio for Visual Studio 6.0 and I encounter: Error 1311 Source file not found, measurementstudio5.cab
Any ideas?

Hello David,
I am also experiencing an Error 1311, but during the install of LabVIEW 2012 and 2013 (64-Bit).
Win7 x64, Acer laptop.
First problem I encounter is:
After putting in my info and agreeing to the licence agreements, the first error pops up says the followign:
NI LabVIEW Run-Time Engine 2011 SP1:
Error 1310. Error writing to file: Crogram Files (x86)\Internet Explorer\Plugins\LV2011ActiveXcontrol.dll. Verify that you have access to that directory.
Options: Abort/Retry/Ignore
Things I've tried:
Retry button--never get's past the error.
Uninstalling Internet Explorer and restarting--Still assumes that it's there, and error remains.
Reinstalling updated Internet Explorer and restarting -- no change.
Checking the directory file and verifying that permissions for every user and System is set to full control -- No change.
The only way to get past this error seems to be to press the Ignore button.
A few moments after ignoring the first error, another error pops up. It says:
NI Labview Run-Time Engine 2011 SP1:
Error 1311. Source file not found: C:\Users\[my U/N]\Desktop\National Instruments Downloads\LabVIEW 64-bit\2013\Products\LabVIEWruntime_mft.cab. Verify that the file exists and that you can access it.
Options: Retry/Cancel
Things I've tried:
Verifying that the file exists (it does) and that I have access to it (I do) and checking the permissions to verify full control --no changes.
Retry -- does nothing.
Cacel --aborts the installation and indicates instal failure.
Can you help me with this? I've installed LV on two other computers and they worked fine, but my laptop simply doesn't want to take the install.
Thank you in advance,
Thomas

Acrobat 7.0 error 1311, file needed

During install, error 1311 comes up. Source file not found C:\Program Files\Adobe\Acrobat 7.0\Setup Files\AcroPro\ENU\Data1.cab , then the process quits and I cannot install product. Any suggestions how I can get this file? Next step?

Windows Vista. I did manage to get through that step, but ran into another error. It appears this may be deeper than I first thought.

Error -1073807253 occurred at VISA Read in transient SR830.vi VISA: (Hex 0xBFFF006B) A framing error occurred during transfer.

Hi,
I am have written a program with labview to make transient c-v measurement using a stanford research SR830 lockin amplifier. The program seems to be runing fine, but sometimes it is givvibg an error:
Error -1073807253 occurred at VISA Read in transient SR830.vi
Possible reason(s):
VISA: (Hex 0xBFFF006B) A framing error occurred during transfer.
Error -1073807253 occurred at VISA Read in transient SR830.vi
Possible reason(s):
VISA: (Hex 0xBFFF006B) A framing error occurred during transfer.
but if I press ok, the program again starts running. What might be the poblem? BTW I googled a bit and I see that in the labview topic "RS-232 Framing Error with HP 34401A Mulitmeter" by pkennedy32 this is what is said about framing error:
""Framing Error" in an RS-232 context means a very specific thing - when the receiver was expecting a stop bit, the line was not in SPACE condition. This can be the result of:
1... Baud rate mismatch (although other problems would likely crop up first).
2... Data Length problem, If I send 8 data bits and you expect 7, the stop bit is in the wrong place.
3... Parity setting mismatch - If I send 7 data bits + parity and you expect 7 data bits and no parity, the stop bit is in the wrong place.
4... Mismatch in # Stop bits - If I send you 7 Data bits + parity + one stop bit, and you expect 7 data bits + parity + TWO stop bits, the second one might not be correct, although most devices do not complain about this.
But, I must say that this is the same com port setting that I use to measure c-v hysterysis, but I never gt this error there.
I attach the program herewith for your kind perusal. Please help me resolve this issue.
Thanks in advance.
Solved!
Go to Solution.
Attachments:
transient SR830.vi ‏94 KB
csac.vi ‏8 KB
sr830 initialize1.vi ‏15 KB

@Dennis Knutson you are right I checked the read indicator in backslash mode, and instead of a \n it is sending \r. So I changed the \n in my write strings to \r. But, if I keep the CLOSE VISA outside my loop instead of inside as you suggested, the termination character appears to come in the middle of the read string instead at the end. And since the read terminates at the \r so it is displaying some junk value before the \r, but if I put the CLOSE VISA outside the loop and play along with the bytes at the read buffer, I see the whole read string with the \r at the end of the string. But, whenever the values are in exponential form (when close to zero) like 6.938839 e-5, I always get a time out error whatever be the timeout that I put at the VISA initialize. And subsequently, if I stop the program and run it again the machine program hangs and I donot get any reading. Then after I close it again and start, sometimes it hangs for some more or starts working. If I put an arbitrarily large byte count at the READ VISA, then I always get the time out before the operation completed error.
@ Ravens Fan I have removed the CSAC VI altogether and taking the CH! And CH” reading separately, instead as one string. So, no more issues with that.
I use the control at the delay so that I can choose how much delay I want to set, and I use the math operation because I am using adding up the delay time to keep track of the time elapsed. Because in the end I have t plot a time vs. CH! And CH” readings.
I am not sure but probably I am making some silly errors. Please help me out.
Attachments:
transient SR830-2.vi ‏103 KB
sr830 initialize1.vi ‏15 KB

LabVIEW FPGA: An internal software error in the LabVIEW FPGA Module has occurred

Hi,
I am trying to build a LabView FPGA VI. During compilation, I always get error stating "LabVIEW FPGA: An internal software error in the LabVIEW FPGA Module has occurred. Please contact National Instruments technical support at ni.com/support". At the time, comiplation process is almost at the end. "Final Timing (place and route)" shows as completed. When Checked the Xilinx log session, at the end it states that " Process "Generate Programming File" completed successfully". However, I do not see any generated bitfile.
When clicked on error details, it shows following:
LabVIEW: An unknown error occurred.
Error -2629 occurred at Error occurred while loading XML string. Invoke Node in niFpgaXml_PrettyPrint.vi->niFpgaWriteBitfileXml_Core.vi->niFpgaCompileWorker_CreateBitfile.vi->niFpgaCompileWorker_JobComplete.vi->niFpgaCompile_Worker.vi:6460001
Possible reason(s):
LabVIEW: An unknown error occurred.
I tried multiple times but so far no luck to generate bitfile for this VI. What could be wrong here?
I am using Labview 2013

Hi Mark,
Here is the device utilization Summary. My development system is running with Windows-7 (32 bit) with 3GB RAM and Labview 2013.
Device Utilization
Total Slices: 90.0% (11970 out of 13300)
Slice Registers: 40.7% (43258 out of 106400)
Slice LUTs: 71.6% (38103 out of 53200)
DSP48s: 1.4% (3 out of 220)
Block RAMs: 22.1% (31 out of 140)
Timing
40 MHz Onboard Clock
: 40.00 MHz (57.90 MHz maximum)
80MHz (Used by non-diagram components)
: 80.00 MHz (100.19 MHz maximum)
--WillsG

Error -64997 during generation intermediate file .

I have face this error Error -64997 during generation intermediate file. I am using Spartan 3E starter kit. Plz tell me what I am do?
Solved!
Go to Solution.
Attachments:
Untitled.jpg ‏151 KB
Untitledd.jpg ‏79 KB

You can find the downloads for LabVIEW 2011 SP1 and LabVIEW FPGA Module 2011 SP1 at www.ni.com/donwloads
Then sort by Software » LabVIEW (for the development environement) and Software » LabVIEW Add Ons (for the FPGA module). Or you can search for any product you desire. If your serial number is not valid for these products then you will only have access to the software for a short trial period. I would recommend checking with the adminstrator of your software license to see which versions you have access to.
Knowledge Base Article titled "Where Can I Find the LabVIEW FPGA for Xilinx SPARTAN-3E XUP Driver?" has links at the bottom of the page which will take you to all the downloads we have available for the FPGA driver for Spartan 3E.
-Nick-
Nick C | Staff LabVIEW Platform Product Support Engineer | National Instruments

An error occurred loading VI. LabView load error code 1: LabView load error code %ld: %p"

I have been developing a VI file that has
been working fine, until now. I am using 8.6.
Every time I attempt to open this file
I keep getting:
How do I fix the error code:
Labview: Memory is
full.
An error occurred loading VI. LabView load error code 1:
LabView load error code %ld: %p”
On a separate dialog:
“Not enough memory to complete this
operation.”
I ran VI analyzer which told that the
VI:
One or more errors occurred during
analysis.
Testing errors tab – Vi not loadable
and my file name. At the bottom in the error description I got:
“Error 74. Memory or data structure
corrupt. <my file path> and <file name>.”
Could not be opened.
Is there anything I can do to recover
the file?

Hi kevin_khan,
I went ahead and tried to open it and got the error attached.
Peter T
Applications Engineer
National Instruments
Attachments:
test.png ‏14 KB

Length error occurred during in IMPORT statement

Dear Friends,
(length error occurred during in IMPORT statement),when im using the SUBMIT syntax..can i know what is the reason.
Thanks
Rajkumar.A

Hello,
I would like to know how did you solve the issue as i came across the same issue.
Thanks,
FBK

RC-00118: Error occurred during creation of database

adcrdb.sh started at Mon Nov 14 16:16:13 EAT 2011
The environment settings are as follows ...
ORACLE_HOME : /u04/d01/tech_st/11.2.0
ORACLE_SID : JCLONE
TWO_TASK :
PATH : /usr/bin:/u04/d01/tech_st/11.2.0/bin:/usr/bin:/usr/sbin:/u0 4/d01/tech_st/11.2.0/jdk/bin:/usr/ccs/bin:/bin:/usr/bin/X11:/usr/local/bin:/u04/ d01/tech_st/11.2.0/appsutil/clone/bin/../jre/jre/bin:/usr/lib/qt-3.3/bin:/usr/ke rberos/sbin:/usr/kerberos/bin:/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbi n:/usr/bin:/usr/X11R6/bin:/root/bin:.
LD_LIBRARY_PATH : /u04/d01/tech_st/11.2.0/lib:/usr/X11R6/lib:/usr/openwin/lib :/u04/d01/tech_st/11.2.0/ctx/lib
Executable : /u04/d01/tech_st/11.2.0/bin/sqlplus
The log information will be written to
/u04/d01/tech_st/11.2.0/appsutil/log/JCLONE_oracle/adcrdb_JCLONE.txt
Creating the control file for JCLONE_oracle database ...
SQL*Plus: Release 11.2.0.2.0 Production on Mon Nov 14 16:16:13 2011
Copyright (c) 1982, 2010, Oracle. All rights reserved.
Connected to an idle instance.
ORACLE instance shut down.
Connected to an idle instance.
ORACLE instance started.
Total System Global Area 1071333376 bytes
Fixed Size 1348968 bytes
Variable Size 427821720 bytes
Database Buffers 629145600 bytes
Redo Buffers 13017088 bytes
CREATE CONTROLFILE REUSE SET DATABASE "JCLONE"
ERROR at line 1:
ORA-01503: CREATE CONTROLFILE failed
ORA-01159: file is not from same database as previous files - wrong database id
ORA-01110: data file 1: '/u04/d01/apps_st/data/system01.dbf'
alter database open resetlogs
ERROR at line 1:
ORA-01507: database not mounted
alter tablespace TEMP add tempfile '/u04/d01/apps_st/data/temp01.dbf' REUSE
ERROR at line 1:
ORA-01109: database not open
ALTER DATABASE RENAME GLOBAL_NAME TO "JCLONE.jtl.co.ke"
ERROR at line 1:
ORA-01109: database not open
ORA-01507: database not mounted
ORACLE instance shut down.
Connected to an idle instance.
ORACLE instance started.
Total System Global Area 1071333376 bytes
Fixed Size 1348968 bytes
Variable Size 427821720 bytes
Database Buffers 629145600 bytes
Redo Buffers 13017088 bytes
Database mounted.
BEGIN dbms_backup_restore.zeroDbid(0); END;
ERROR at line 1:
ORA-01119: error in creating database file
'/u04/d01/tech_st/11.2.0/dbs/MISSING00015'
ORA-27037: unable to obtain file status
Linux Error: 2: No such file or directory
Additional information: 3
ORA-06512: at "SYS.X$DBMS_BACKUP_RESTORE", line 4754
ORA-06512: at line 1
ORACLE instance shut down.
Connected to an idle instance.
ORACLE instance started.
Total System Global Area 1071333376 bytes
Fixed Size 1348968 bytes
Variable Size 427821720 bytes
Database Buffers 629145600 bytes
Redo Buffers 13017088 bytes
CREATE CONTROLFILE REUSE SET DATABASE "JCLONE"
ERROR at line 1:
ORA-01503: CREATE CONTROLFILE failed
ORA-01159: file is not from same database as previous files - wrong database id
ORA-01110: data file 1: '/u04/d01/apps_st/data/system01.dbf'
alter database open resetlogs
ERROR at line 1:
ORA-01507: database not mounted
alter tablespace TEMP add tempfile '/u04/d01/apps_st/data/temp01.dbf' REUSE
ERROR at line 1:
ORA-01109: database not open
ALTER DATABASE RENAME GLOBAL_NAME TO "JCLONE.jtl.co.ke"
ERROR at line 1:
ORA-01109: database not open
Error Running create/replace library with adupdlib.sql
ORA-01109: database not open
PL/SQL procedure successfully completed.
File created.
Disconnected from Oracle Database 11g Enterprise Edition Release 11.2.0.2.0 - Pr oduction
With the Partitioning, OLAP, Data Mining and Real Application Testing options
exit_code=0
Checking for errors ...
The database has not been successfully created. Shutting down the instance ...
SQL*Plus: Release 11.2.0.2.0 Production on Mon Nov 14 16:16:32 2011
Copyright (c) 1982, 2010, Oracle. All rights reserved.
Connected.
ORACLE instance shut down.
Disconnected from Oracle Database 11g Enterprise Edition Release 11.2.0.2.0 - Pr oduction
With the Partitioning, OLAP, Data Mining and Real Application Testing options
.end std out.
.end err out.
ADX Database Utility
getConnectionUsingAppsJDBCConnector() -->
APPS_JDBC_URL='null'
Trying to get connection using SID based connect descriptor
getConnection() -->
sDbHost : oracle
sDbDomain : jtl.co.ke
sDbPort : 1524
sDbSid : JCLONE
sDbUser : apps
Trying to connect using SID...
getConnectionUsingSID() -->
JDBC URL: jdbc:oracle:thin:@oracle.jtl.co.ke:1524:JCLONE
Exception occurred: java.sql.SQLException: IO Error: The Network Adapter cou ld not establish the connection
Trying to connect using SID as ServiceName
getConnectionUsingServiceName() -->
JDBC URL: jdbc:oracle:thin:@(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=oracle .jtl.co.ke)(PORT=1524))(CONNECT_DATA=(SERVICE_NAME=JCLONE)))
Exception occurred: java.sql.SQLException: IO Error: The Network Adapter cou ld not establish the connection
Trying to connect using SID as ServiceName.DomainName
getConnectionUsingServiceName() -->
JDBC URL: jdbc:oracle:thin:@(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=oracle .jtl.co.ke)(PORT=1524))(CONNECT_DATA=(SERVICE_NAME=JCLONE.jtl.co.ke)))
Exception occurred: java.sql.SQLException: IO Error: The Network Adapter cou ld not establish the connection
Connection could not be obtained; returning null
-------------------ADX Database Utility Finished---------------
RC-00118: Error occurred during creation of database
Raised by oracle.apps.ad.clone.ApplyDatabase
StackTrace:
java.lang.Exception: Control file creation failed
at oracle.apps.ad.clone.ApplyDatabase.<init>(ApplyDatabase.java:661)
at oracle.apps.ad.clone.ApplyDatabase.<init>(ApplyDatabase.java:328)
at oracle.apps.ad.clone.ApplyDatabase.<init>(ApplyDatabase.java:304)
at oracle.apps.ad.clone.ApplyDBTier.<init>(ApplyDBTier.java:154)
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstruct orAccessorImpl.java:39)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingC onstructorAccessorImpl.java:27)
at java.lang.reflect.Constructor.newInstance(Constructor.java:501)
at oracle.apps.ad.clone.util.CloneProcessor.run(CloneProcessor.java:68)
at java.lang.Thread.run(Thread.java:595)
Current database Version is 11.2.0.2
Apps Version is 11.5.10.2
RUP version is 6
Forms Patchset version is 19
Please advise how to resolve this error ?
Regards
Mohammed.

Please refer to these docs/links.
Troubleshooting RapidClone issues with Oracle Applications 11i [ID 364565.1]
Adcfgclone.pl DBTier is failing with error for dbms_backup_restore.zeroDbid(0) [ID 361157.1]
https://forums.oracle.com/forums/search.jspa?threadID=&q=ORA-01503+AND+ORA-01159+AND+ORA-01110&objID=c3&dateRange=all&userID=&numResults=15&rankBy=10001
Thanks,
Hussein

Error 1935 an error occurred during installation of assembly component

I get this message when trying to install Lightroom 4.3
error 1935. an error occurred during installation of assembly component {6435B7C0-E0C8-3EA2-91AE-7640034EAFCE} hresult 0X800700C1
I've tried installing with antivirus software shut down. I've reset the file system transaction log. I turned off the .net framework v 3.0 in the programs and features section of control panel. The only thing I haven't tried is deleting the .net framework because the other articles were unclear as to exactly what and how to delete them.
Please help!

that looks like an ms error.
attach a screenshot, if you're not sure.

Error occuring during import of certificate for SSO configuring in BI

Hi,
I am configuring the SSO with logon ticket for BI system.
I downloaded the certificate from portal server.
But while importing this certificate on R/3 server it shows error
"Error occurred during import"
Message no. TRUST008
Please suggest me any solution on it.
Thanks & Regards,
Vishal.

Hi Vishal,
Probably the certificate already exists - see https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/0077873d-0b01-0010-1abb-cfbf21d1aa43 page 4.
Hope it helps
Detlev

Error 1311 during LabVIEW installati​on

Similar Messages

Maybe you are looking for

Error 1311 during LabVIEW installation