Error 3004, stuck on Recovery mode.

Hi,
My iPhone 4S is stuck on recovery mode.
Everytime I try to restore, Error 3004 occured.
Pls Help

DId you try:
Try to restore or update on another computer with a different Internet connection.

Similar Messages

  • Iphone Unknown Error 40 stuck in recovery mode

    Hi,
    My question is... if my iphone is stuck in recovery mode and I return it to the shop I bought it from and they give me my money back/replace it etc, if they then do get the phone to work will they be able to see all my data/photos/messages etc? Or will it only restore personal data if the phone is restored from my itunes?
    I updated my Iphone 4 via Itunes yesterday and it's now stuck in recovery mode, every time I try to restore the phone it gets to "waiting for iphone" then Unknown error 40 appears.
    I have tried the suggestions here:
    http://support.apple.com/kb/TS3694
    I am going to take it to the apple store genius next week, but first am returning it to the shop I bought it from as they want to see if they can fix it (it was unlocked when I bought it, they claimed it was an apple unlocked phone but I am concerned it was in fact unlocked by them and this is why I am having problems).  Hence my question being, will they be able to restore it to my data without access to my itunes to back it up from?  Will it just be a factory setting reset if they fix it (which I'd prefer)?
    Thanks in advance!
    C

    Hi Fkaram,
    Sorry to say I haven't found a solution (after hours of searching!) and have bought an android moto g. The only difference from yours is that I replaced the dock connector as I kept getting error 4014, which turned it on after being off for three weeks, and then went to error 40.
    If you haven't got a warranty, I can only suggest replacing the dock connector. Its cheap (£5) and pretty easy to fix. I only tried this because changing the leads didn't work, but I kept getting the faulty leads error (4014+40)
    Good luck!
    ps - check for any bent pins or if there is a red/coloured light in the connector itself. I didn't see any bent pins so was lucky the replacement actually did something
    Message was edited by: Harry Jones3

  • Help iPhone 4s could not restore (error 1) - stuck in recovery mode

    I thought I had successfully converted from iPhone 3g to 4s could not connect to att phone service.  To reinstall, I reset to iPhone 4s to restore factory settings. software downloaded successfully, but after install completes I get a message that iPhone 4s could not restore (error 1).  Followed by message that iTunes has detected an iPhone in recovery mode and that I can restore original setting bu clicking Restore.  Doing that reats the problem  After 10 attempts, I am frustrated.  Itunes no longer shows capacity, software version or serial number for iPhone .  Lists those as n/a.  Need help

    Unfortunately the restore did not solve the connectivity problem, but it made it even worse. The phone was not connecting to the carrier at all, constantly showing "Searching...". I tried another restore, this time it failed on three different computers (one of them was a fresh iTunes installation)... Strange, that it worked once.
    @Unshaven: Multiple combinations of Power and Home button did not work either. Seems to be bricked now. I think I have to return it to Apple ...
    Btw. Windows iTunes showes some log errors like 'getenv radio-error' failed and DoesDriverNameMatchDeviceID failed.
    Any ideas welcome also regarding the issue of loosing connectivity to the carrier...

  • IPad 3 - 3g Version Restore error 1 (stuck in recovery mode)

    Hi all,
    I tried updating my iPad after lending to a friend for a plane trip, when i went to update it i left it go and came back with an error on there. The iPad was working completely fine before trying to update and now every time i go to update or restore will come with either error 1 or if i try different way i get 3194.
    any help would be appreciated i just don't get why trying to update Via apple bricked my iPad, don't care if i lose the stuff on there so any help appreciated
    thanks.

    Hello reedyx,
    Thanks for using Apple Support Communities.
    To help resolve this issue where your iPad is getting error 1 when trying to restore, please follow the directions outlined below.
    Check for hardware issues
    Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
    These errors mean that your device or computer may have a hardware issue that's preventing the update or restore from completing.
    Check that your security software and settings aren't preventing your device from communicating with the Apple update server.
    Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
    Confirm that your security software and settings are allowing communication between your device and update servers.
    If you still see the error message when you update or restore, contact Apple support.
    Resolve iOS update and restore errors - Apple Support
    Take care,
    Alex H.

  • Updating IOS Failed and stuck on recovery mode

    i'd tried to update my iphone 4 ios 7.0.4 to 7.1, but it gave error and stuck on recovery mode i tried to restore it to previous ios but failed again, anyone have idea what i should do to restore iphone to previous ios or ios 7.1 ...

    You can't restore to a previous iOS. Try this procedure:
    Turn your phone off and connect your cable to the computer, but not the device just yet. Start up iTunes. Now, hold down the home button on your phone and plug it in to the cable - don't let go of the button until iTunes tells you it's detected a phone in recovery mode. Now you can restore to factory settings.

  • IPod stuck on recovery mode cannot restore error 3004

    Hello,
    My iPod Touch 5th gen is stuck on recovery mode for two days now. I have lost all of my important files, but I am hoping to make it work again.
    I was updating to ios 8 the other day and suddenly my iPod turned off and was stuck on recovery mode. No big deal, but then, as I was to restore it, iTunes only says that "The iPod 'iPod' could not be restored. An unknown error occurred (3004)."
    I'm here now because I have tried all of the fixes. I have tried to put it on DFU mode (didn't work), changed my DNS settings, updated my iTunes, uninstalling, reinstalling it, turned my PC on and off, used another PC, but nothing has worked. I used some external programs that can get my iDevice to get in and out of DFU mode, but it has not worked.
    I am on PC, Windows 8.
    Hope anyone can help.

    DId you try:
    Try to restore or update on another computer with a different Internet connection.

  • My IPad is stuck in recovery mode and now ITunes wont recognize it, what do I do? Keeps giving me a long error message.

    My IPad is stuck in recovery mode and now ITunes will not recognize it, it just gives me this long error message. What do I do, I've uninstalled and reinstalled ITunes.

    Check USB connections
    Related errors: 13, 14, 1600, 1601, 1602, 1603, 1604, 1611, 1643-1650, 2000, 2001, 2002, 2005, 2006, 2009, 4000, 4005, 4013, 4014, 4016, “invalid response,” and being prompted to restore again after a restore completes.
    If there’s an issue with the USB port, cable, dock, or hub, or if the device becomes disconnected during restore, try troubleshooting the USB connection, then troubleshooting your security software.
    To narrow down the issue, you can also change up your hardware:
    Use another USB cable.
    Plug your cable into a different USB port on your computer.
    Try a different dock connector (or no dock).
    Add (or remove) a USB hub between your device and computer.
    Connect your computer directly to your Internet source, with no routers, hubs, or switches.
    If you checked your connections and are still seeing the error message, check for hardware issues.
    Check for hardware issues
    Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
    Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the error message when you update or restore, contact Apple support.

  • I just tried to update my iphone 4 to the 5.01. My iphone  backed up and started update but now its stuck in recovery mode and will not restore. It gives me an error message of 1, but I have tried everything on troubleshoot list and still wont work!!!!

    I just tried to update my iphone 4 to the 5.01. It said that my phone backed up and started update. i went on a run and came back and my phone is now stuck in recovery mode. It keeps saying that there is an unknown error, 1. I have tried everything on the troubleshooting list and cannot figure out what is wrong! Please HELP!!!

    http://support.apple.com/kb/TS3694#error1

  • How do i fix my iphone 5 stuck in recovery mode and wont let me restore it just says unknown error 1603 has occured

    how do i fix my iphone 5 stuck in recovery mode and wont let me restore it just says unknown error 1603 has occured

    http://support.apple.com/kb/TS3694#error1603
    Follow the steps listed above for Error 1604. Also, discard the .ipsw file, open iTunes and attempt to download the update again. See the steps under Advanced Steps > Rename, move, or delete the iOS software file (.ipsw) below for file locations. If you do not want to remove the IPSW in the original user, try restoring in a new administrator user. If the issue remains, Eliminate third-party security software conflicts.
    http://support.apple.com/kb/TS3694#error1604
    This error is often related to USB timing. Try changing USB ports, using a different dock connector to USB cable, and other available USB troubleshooting steps (troubleshooting USB connections. If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
    If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
    Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode, put it into Recovery Mode.
    Restore and wait for the error.
    When prompted, click OK.
    Close and reopen iTunes while the device remains connected.
    The device should now be recognized in Recovery Mode again.
    Try to restore again.
    If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.

  • My ipod touch is stuck in recovery mode I tried RecBoot and the reiBoot  both fail to get me out of recovery  I get error 28 instad  now what?

    My ipod Touch 2nd Gen 8GB is stuck in recovery mode   I tried RecBoot and when that couldn't do it I tried reiBoot  both failed to fix my problem  what do you suggest?

    Start off with some basic steps:
    - Make sure iTunes is up to date
    - Try another usb cable
    - Try another usb port
    In the article Resolve iOS update and restore errors this is what it says about error 28:
    Check for hardware issues
    Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
    These errors mean that your device or computer may have a hardware issue that's preventing the update or restore from completing.
    Check that your security software and settings aren't preventing your device from communicating with the Apple update server.
    Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
    Confirm that your security software and settings are allowing communication between your device and update servers.
    If you still see the error message when you update or restore, contact Apple support.

  • Ipod touch stuck in recovery mode and will not restore. error code 3194

    ipod touch stuck in recovery mode, will not restore and comes up with error code 3194, itunes is up to date, please help

    Hi @rchangel - Thanks for the ideas...
    Yes - it won't let you install the 32 bit version on a 64 bit machine.
    I've had a cursory look at the SP1 release notes, and couldn't spot anything vital - what critical stuff do you know of in SP1?
    I don't want to have to go through all the pain of setting up VM's, reinstalling iTunes, getting all my album art back in etc. (though I could, as I do have Win7 pro). I've also heard that running iTunes in Windows 7 compatibility mode might help. Can anyone confirm whether that actually works?
    I think it's in Apple's gift to fix this issue, given that they say that they support Windows 7. So far I've had no feedback from a mail I sent to Apple, and the number of users reporting this problem keeps going up and up.
    I want Apple to recognise that there is a problem, and then I want them to fix it.

  • Ipod touch is stuck in recovery mode with a error code 9

    my ipod touch is stuck in recovery mode and when i try to restore it getting an error code 9

    Error 9: This error occurs when the device unexpectedly drops off the USB bus and communication stops. This can occur if the device is manually disconnected during the restore process. This issue can be resolved by performing USB isolation troubleshooting, using a different USB dock-connector cable, trying another USB port, restoring on another computer, or by eliminating conflicts from third-party security software.
    From:
    http://support.apple.com/kb/TS3694

  • My iPhone 5s is stuck in recovery mode and won't turn on, I've tried to restore and update it to iTunes and its finding my phone, but saying an error has occurred, any ideas?

    My iPhone 5s is stuck in recovery mode and won't turn on, I've tried to restore and update it to iTunes and its finding my phone, but saying an error has occurred and won't work, the software is up to date, it just automatically switched itself off and when I try to turn it on, it shows the White background with the apple logo asif it's going to turn itself on but then switches off after a couple of seconds, what can I do? ive already taken it to a shop and he's looked at it, but said he can't fix it, thanks.

    Visit an Authorized Apple Service Provider or Apple Store to get it checked. If they can't fix this, you'll have to pay the Out-Of-Warranty-Service fee to get a new replacement for a reduced price:
    Out-of-warranty repair service
    If your repair isn’t covered by Apple’s One Year Limited Warranty, AppleCare+, or AppleCare Protection Plan, your iPhone might be eligible for out-of-warranty service. For example, liquid damage isn’t covered by warranty but might be eligible for out-of-warranty service. Some damage isn’t eligible at all, for example if your device has been broken into multiple pieces. See Apple’s Repair Terms and Conditions for complete details.
    Read Apple’s Repair Terms and Conditions
    Model
    Out-of-warranty service fee
    Battery service*
    iPhone 6 Plus
    $329
    $79
    *available only if battery
    fails Apple’s diagnostic test
    iPhone 6
    $299
    iPhone 5s, iPhone 5c, iPhone 5
    $269
    iPhone 4s
    $199
    iPhone 4, iPhone 3GS, iPhone 3G,
    Original iPhone
    $149
    Plus a $6.95 shipping fee, if required. Fees are in USD and exclude local tax. Pricing is for service through Apple. The final service fee we charge will be determined during testing and may be less than the service fee listed above. Pricing and terms vary for service through an Apple Authorized Service Provider.
    copied from Service Answer Center - iPhone

  • TS3694 error code 3914. Does anyone know how to solve this problem? My ipod touch is stuck in recovery mode. would be grateful of any help.

    Ive been trying to restore my ipod touch and it comes up with the error code 3914. Also, the ipod is stuck in recovery mode. Can anyone help?

    http://support.apple.com/kb/TS3694#error3194
    I realize you already saw this knowledge base article, but you need to read it more carefully.

  • My Ipod touch is stuck in recovery mode. I keep getting Error 9 and I have done everything they asked but nothibng helps.

    Help I think when I went to restore my ipod touch the date was wornign on the ipod and not it is stuck in recovery moder and I keep getting Error 9. I have tried everything but nothing works can someone help me?

    Error 9: This error occurs when the device unexpectedly drops off the USB bus and communication stops. This can occur if the device is manually disconnected during the restore process. This issue can be resolved by performing USB isolation troubleshooting, using a different USB dock-connector cable, trying another USB port, restoring on another computer, or by eliminating conflicts from third-party security software."- it's taken from the Apple support web.

Maybe you are looking for

  • Re: MMAPI sound application

    First, you must check that your phone supports this API. If it does, then you can write your app and you won't have to include anything in your JAR. Just compile and link against the mmapi api libs and you'll be set. Install the app on your device an

  • Basic PL/SQL parser usage?

    First off, I have to say that the documentation (what little there is) for the pl/SQL XML parser is absolutely terrible. I've figured out the bulk of it through trial and error, and some examples, but I'm stuck on something very basic. How do I get t

  • Count the no.of of numericals from a string.

    Hi team I would like to count the no.of numericals from a given string. Ex. String - '1,23,567 8-9' The result should be 5. Eliminate the comma and space and hypen (-) while counting. 1 - is 1 23 - is 2 567 - is 3 8 - is 4 9 - is 5 Kindly help me. Re

  • Smart Album Scope

    I have been using Aperture 1.5.1 and have noticed what I consider to be strange or, at least, non-intuitive behavior for smart albums. I'm wondering if others have had the same experience and if Apple considers this normal behavior. First, some backg

  • Styling spry:sort

    Is it possible to apply some css styling to a <th> with a spry:sort to give some indication of which column in a table is currently the one that the table is being sorted by?