Error 45048 - itunes - Win XP PRO

I have a problem with my iTunes. After i updated my iTunes to 11.1.3.8, i can no longer download songs, apps or updates apps with my iTunes PC. The notif always, "An unkown error occured (-45048). I use windows XP PRO service pack 3. i try to uninstall the iTunes and then install it again but nothing happened. Same problem. i dont know where is the problem. I saw that for Win 7 there is a solution by deleting the SC Info folder... but what is solution for Win XP PRO ?

I am not re-ripping my CD's to AAC
Huh?
Then why did you write, "decided to use iTunes, and set it to Rip my CD's to AAC"?
If possible (and for best quality) you should RIP for the CD and not convert between lossy formats (AAC/MP3/WMA).
My question was simply why does iTunes take 3 times as long to RIP a CD at 128kbs AAC then WMP10 does to rip a CD to 192kbs WMA, and what can I do to give iTunes a boost?
In response to yoru question, Pac wrote;
"1) UPDATE FIRMWARE for the CD burner drive and get the latest updates for your system,like BIOs hardware ect ect from the PC makers site
2) Slow the burn speed from "Max" downto 16x 8x or 4x"
The reason I would prefer to go with AAC is that for the "same" bit rate/quality as MP3 you actually end up saving some space - on my calculation about 25% - so that is preferable.
You must be calculating something incorrectly.
Using iTunes to RIP, AAC and MP3 at the same bit rate are almost identical in file size.
The quality is definitely not the same.
There are better MP3 codecs available(LAME).
if there is other software out there that will RIP to AAC - and is faster than iTunes - then let me know.
Yes, there are different apps that will RIP AAC, but I can't recall offhand.

Similar Messages

Mtp usb device failed error - iphone 3g - win 7 pro

I have iphone 3g. I use Win 7 pro OS. when i plug in iphone to usb port, i get error message as - device driver failed to install - in detail - mtp usb device failed..
In iTUNES i am able to view the iphone, sync my contacts with MS outlook etc..
kindly help
shansui

What a load of hogwash.
I've just had this error come up - WITH NO CHANGE OTHER THAN UPGRADE OF IPHONE 4 TO IOS 5.1.1.
(running iTunes 10.6.1.7 on 64 Win7)
Powered phone off, and back on again - same error... Haven't had to reinstall windows in a few years - maybe iTunes is now the least stable software in my collection - Might have to try the two (button) salute to Apple...
Error on device "MTP USB Device";
"This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)"

Error code 50 Win 7 pro 64 bit

I received the desktop update notification, tried to update it and kept getting this error message:
I uninstalled the desktop app, tried a clean install and I still keep getting this error message.
I am also running another machine on Win 7 Pro 32 bit and I haven't had this issue.

1) End all Adobe related process from Task Manager .
2) Open Control Panel and Navigate to Control Panel\Programs\Programs and Features .
Under Program and Features list, let me know whether you can see the option : Adobe Creative Cloud ?
If not proceed with below steps.
3) Open C:drive and navigate to C:\Program Files (x86)\"Common Files"\Adobe.
Open Adobe folder and delete folders named Adobe Application Manager and OOBE.
Navigate to C:\Program Files (x86)\Adobe.
Open Adobe folder and if present delete Adobe Creative Cloud folder.
4) Press Windows button (located between Ctrl and Alt buttons) along with R button together at a time , you will get a run command window.
Type in below command and hit 'Enter' key.
appdata
Then navigate to Local>Adobe.
Open Adobe folder and delete folders named AAMUpdater and OOBE.
Note : Disable Anti-Virus and Firewall temporarily
5)
Click on the below link and download Adobe Application Manager and install the same .
http://download.adobe.com/pub/adobe/creativesuite/cc/win/ApplicationManager9.0_all.exe
6)Once installed , it will create Adobe Application Manager shortcut icon on Desktop .
Double click on it.
It will start update process and gets updated to Creative Cloud.

0xc004e003 error while activating Win 7 Pro on Portege R930-17L

Toshiba Portege R930-17L
S/N: 5D016093H
(If I search on Toshiba after SN I only find it in Toshiba - Ukraine)
Bought from "Sigmanet" online shop in Romania.
It has a sticker on the back side w/ Windows 8 Pro (small sticker without product key).
It arrived with Windows 8 install CD.
On it was preinstalled Windows 7 Pro SP1 x64 (this notebook has the right to use Windows 8 and Windows 7)
Of course, the preinstalled OS was running slow and gave errors (McAfee AV preinstalled, a bunch of small apps, a.s.o.)
I reinstalled Windows 7 Pro SP1 x64 (original CD) on clean partition.
I can't activate it with the following:
Product Key: XXXXX-YYYYY-ZZZZZ-XXXXX-YYYYY
Product ID: xxxxx-OEM-xxxxxxx-xxxxx
Error code: 0xc004e003
Now, I've spoken with Microsoft Romania, they tried to help me but they failed.
They told me that the license appears to be blocked from Toshiba, so they suggested me to contact them (Toshiba) for unblocking the license or for providing a new product key.
So, I've contacted the seller. They passed me to Toshiba authorised service in Romania which avoids to help me.
Now I'm stuck. What to do or whom to contact. Everything is so blurry ...
I appreciate any response you can give me. Thanks!

> It has a sticker on the back side w/ Windows 8 Pro (small sticker without product key).
>It arrived with Windows 8 install CD.
>On it was preinstalled Windows 7 Pro SP1 x64 (this notebook has the right to use Windows 8 and Windows 7)
Toshiba notebooks are preinstalled with Windows systems which are already activated.
The stickers you can find at the bottom of the units are OEM serial keys and such keys dont work in connection with other different system. The OEM key belongs to the preinstalled image.
So in case you would use the Toshiba recovery disk and would install the Windows system using such disk, the serial key would not be necessary.
According to the Toshiba specification page:
http://www.toshiba.co.il/en/laptops/portege/r930/portege-r930-17l/ the notebook was preinstalled with Windows 7 Pro 64bit.
This means that Win 7 Recovery DVD was not part of the package. Why?
because the Toshiba Recovery Media Creator software was preinstalled on such notebook. The software allows you to create the Recovery DVD containing the Win 7 64bit Pro system and image which is activated.

Error installing itunes win 7 home . Run time error R6034 and Error 7 windows error 1114

I receive these error messages trying to re-install itunes:
Run time error R6034 and
Error 7 Windows error 1114.
started happening about a week ago.
Any help?
I tried removing and reinstalling already, same mesages
G

Check for .dll files Go to C:\Program Files (x86)\iTunes and C:\Program Files\iTunes and look for .dll files. If you find QTMovie.DLL, or any other .dll files, move them to the desktop. Reboot your computer. Note: Depending on your operating system, you may only have one of the listed paths.
So they want me to put all of the DLL files to desk top? I dont have any that have QTmovie
I have:
In itunes .resources folder:
itunes.dll
itunesRegistry
In itunesHelper.resources folder
ituneshelper.dll
In Itunes main folder: ie. program files (x86) Itunes
gnsdk_dsp.dll
gnsdk_musicid.dll
gnsdk_sdkmanager.dll
gnsdk_submit.dll
iAdCore.dll
itunes.dll
itunesadmin.dll
ituneshelper.dll
itunesoutlookaddin.dll
Sorry I'm not a real computer dude but would like to resolve and not lose all my music etc.
Thanks
G

Error -2048 QT / Win XP PRo

Hello,
I have been trying to get a .MOV file to play which a client has sent me showing a fault.
Error 2048: Couldn't open the file xxx.MOV because it is not a file Quick time understands.
How can I play this file? Other QT files play. Where can I find a WINDOWS Plug in?
Thank You,
Wes

did you try this easy way?
go to the BIOS and disable all usb ports.
(i would do that too)

No audio from iTunes, WIN 7 PRO

I'm VERY experienced at audio, recording and sound. I've used iTunes for years with no problem. I just installed new iTunes to newly reformatted WIN7PRO and I have no audio. I do have audio from all other sources. I have expended all known remedies, including internal and preferences.

Possible remedies:
Check that you have the most recent version of iTunes (12.1.1.4 - released Feb. 18). The previous release (12.1.0.71) was widely reported to have significant playback issues, varying from "static" and stuttering to complete lack of output. The 12.1.1.4 release seems to fix most of these issues, in some cases in conjunction with the points below.
Check the setting of Play Audio Using in Edit > Preferences > Playback (you'll have to restart iTunes for changes to take effect). iTunes 12.1 sometimes defaults this to "Windows Audio Session" rather than "Direct Sound" where (for most users) the latter works better. In some cases, the 64-bit version of 12.1.0.71 did not have the Direct Sound option available, though this was more widely reported for Windows 8.
Check that you have the latest version of QuickTime (7.7.6) installed. Several people have encountered the problem you describe on new or re-built PCs where QuickTime had not been installed. This issue seems to affect Bluetooth audio devices though may not be exclusive to these.
There's an alternative installer here: iTunes 12.1.1 for Windows (64-bit — for older video cards) - some users have reported that installing this has addressed the problem you've encountered. The "for older video cards" is a something a misnomer - like most prior "64-bit" releases of iTunes, this is a 32-bit application with a 64-bit installer. The "standard" 64-bit version (12.1 and 12.1.1) is a full 64-bit application, but there appear to be a small number of possible incompatibilities between these and some 64-bit Windows systems.

Win 7 Pro error R6034 after itunes 11.4

I just installed itunes 11.4 on my Win 7 Pro system, which has all patches up to date. After installing, all itunes services and itunes itself get the following error: application has made an attempt to load the C runtime library incorrectly. (I *did* run the installation as administrator, and my user id is in the administrator group.)
Any ideas how to fix this?
TIA

Try complete uninstall and reinstall per this article.

Tried to install iTunes with Win 7 Pro and I get an error 2 message that tells me to uninstall and reinstall iTunes. I get the same failure each time.

Tried to install iTunes with Win 7 Pro and I get an error 2 message that tells me to uninstall iTunes and reinstall, same error occurs. What's up?

Hello, rodneywjr.
Thank you for visiting Apple Support Communities.
Here are a couple troubleshooting articles that I would recommend going through when experiencing this issue.
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/ts5376
Issues installing iTunes or QuickTime for Windows
http://support.apple.com/kb/ht1926
Cheers,
Jason H.

ITunes 10.1.2 upgrade on Win XP Pro SP3 Kills Internet access

The latest iTunes 10.1.2 install on my Win XP Pro SP3 system kills my Internet access. Internet status shows that I'm connected but Internet Explorer and Firefox can't connect to the server. Running Win XP Pro SP3 with all MS updates applied on a Dual-Core Intel 6600 chip, 4 gig of memory and a couple of terabytes of hard drive. When I do a restore from my backup hard drive to the prior OS and iTunes version, everything is back to normal. I didn't receive any error notifications both times from the install. I first did the install from the Apple website directly (and lost Internet access), then restored my backup system and downloaded the update separately and then installed and lost Internet access again. Am now back up using iTunes 10.1.1.4. Is this update from Egypt? (supposed to be funny).
Thanks-
Richard

Thanks for the link. I noticed that "Swut" from Orange County, Ca (see the post below) had a reply in the link you gave me referring to "Vipre" , which is an Anti-Virus program that I also use, like "Swut".
I will investigate this further. In defense of Apple, there is no way that they can test against every bit of software that we run on these PCs. I would hope that if we find out that there is some problem with the Vipre interface, both Apple and the Vipre people will be made aware of the problem.
Before I try the iTunes 10.2.1 upgrade again, I'll contact Sunbelt Software- the people who make Vipre and see if they have heard of this problem. I'll let all of you know what the results are.
Thanks- Richard Van Nostrand
"From Swut
From: Orange County, CA
Registered: Jan 28, 2008
Re: iTunes 10.1.0.56 update kills network interface - Windows 7
Posted: Dec 12, 2010 2:32 AM in response to: TG10987
I didn't have to go all the way through with TRG10987s solution. When I got to step 4 I noticed that VIPRE had installed multiple virtual network adapters on to of the network adapters. I uninstalled VIPRE thereby deleting the virtual adapters ran the upgrade, and reinstalled VIPRE. Everything works fine now.
Thanks to TG10987, who put me on the path."

Why i can't install itunes on my PC with win 7 pro 32 bit ?

dear apple.
Could you tell me how to install itunes 10 or 11 on my pc with win 7 pro 32 bit ?
when i try to installing itunes my PC has appear error so i can't complet install itune on my PC
Im trying many time but it just send me error and i cant finish installing itunes
So could you tell me how to fix that ?
Thanks
Jonny

For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it, which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
tt2

Windows Update Loop - Win 7 Pro - x64 :: Error 80071A91

Hi, I've been referred to this forum by the Microsoft community from this post: answers.microsoft.com /en-us/windows/forum/windows_7-system/windows-update-loop-win-7-pro-x64-error-80071a91/b17c5bc5-7977-4f8b-9b45-ecb265886381 (same as below)
Any assistance is appreciated. dave_ned at hotmail.com.
Hi,
"There is a system repair pending which requires reboot to complete. Restart Windows and run sfc again"
I've got the error (80071A91) that others have experiences while trying windows update and for the life of me I cannot get the updates to install.
Looking for the past 4 hours via Google, trying different recommended things and still no luck
http://answers.microsoft.com/en-us/windows/forum/windows_vista-windows_update/unable-to-install-updates-getting-error-code/27a21977-f964-4376-bfab-2f29ea127c6a
# SFC /scannow causes the "repair status message" and asks for reboot.
I've downloaded fix-it, tried booting into a system repair/restore disk using command line to run
#sfc /scannow /offline....
using the dispart to LIST VOLUMES (based on this http://mikemstech.blogspot.com.au/2011/12/how-to-perform-offline-system-integrity.html )
I've tried #fsutils resourse set autorevert=true (or something, can't find the exact post as I've rebooted so many times)
I've tried dismc.exe (or similar without success)
Basically I'm stuck with these updates (~10 of them) always sitting there downloading, installing every time I shut down the PC.
Running a system repair disk created in windows still does not allow #sfc /scannow....
My Last system restore was 04/08/14 and I cannot even restore the system to this point as the restore fails and asks to remove itself once I restart the system.
Details:
OEM version of windows purchased legally and genuine microsoft logo in system dashboard.
Intel Core I5 -3330
16GB RAM
Windows 7 Pro - 64bit OS
Service pack 1
**NOTE** I have the C drive hooked up in RAID 0. Two(2) * 60GB SSD disks in RAID 0 used as C: via BIOS RAID
Secondary storage disk a D:
Been working and updating fine for the past 5-6 months.
I have the Optical drive setup as O: and a Daemon tools virtual drive as drive E:
While running DISKPART and using LIST VOLUME I see this:
currently the system seems to have lost all update history
Any information or help on this is appreciated. I don't want to reformat and reinstall, I don't really want to 'repair' and wipe my current software installation so I'm hoping there is a way.
Anyway I can get the 'pending state' removed.?
Thanks in advance
David

Hi, I've rebooted into Repair mode (Console), (because repair said windows is installed on E:) run dism.exe /image:E:\ /cleanup-image /revertpendingactions
This gave a message about small scratch space but did say something out a fix. Upon reboot into safemode with console I received the same message
"C:\Windows\system32>sfc /scannow
Beginning system scan. This process will take some time.
There is a system repair pending which requires reboot to complete. Restart Windows and run sfc again."
I then rebooted and tried SCF again, no luck... Same message, same updates still sitting there.
Partition info: (as mentioned earlier C is in RAID 0 with 2 SSD disks)
DISKPART> list volume
Volume ### Ltr Label Fs Type Size Status Info
Volume 0 O DVD-ROM 0 B No Media
Volume 1 E DVD-ROM 0 B No Media
Volume 2 System Rese NTFS Partition 100 MB Healthy System
Volume 3 C NTFS Partition 111 GB Healthy Boot
Volume 4 D GB320 NTFS Partition 298 GB Healthy

ITunes 12.1.1 installation errors and resolution (Win 7, 64 bit)

I am providing all of the installation errors I had experienced
and all of the methods I had tried until I finally came up with a solution.
Hopefully the details will help you see if your situation has similarities
which hopefully will make this post helpful in terms of a solution.
PART ONE: INSTALLATION ERRORS
I received the following installation errors
when attempting to update to 12.1.1
and later once I uninstalled and attempted to reinstall 12.1.1.
I used this link for the download:
http://www.apple.com/itunes/download/?cid=wwa-us-kwg-music-itu
> itunes 6464setup.exe
I then tried this link:
http://support.apple.com/kb/DL1614
> itunes 12.1.1 64 bit
Again 6464 in the name.
After uninstalling the iunes,
I discovered under add/remove programs:
apple application support 32 bit
and apple support update
I deleted these and restarted the PC.
I then tried reinstalling a NEW version
from the second link above.
Opened download iTunes 6464setup.exe >
Windows installer> iTunes > welcome to itunes
> next > installation options > install > user account control
> yes > next > (error message via pop-up window):
ERROR MESSAGE ONE
"An error occurred during installation of assembly Microsoft VC80 CRT Type ="win32",
version = "8.0.50727.6195".publicKeyToken="1fc8b3b9a1e18e3b"
processorArchitecture ="amd64".
Please refer to Help and Support
for more information.
HRESULT: 0X80070091"
> OK > iTunes > Status: Starting services >
(error message via pop-up window):
ERROR MESSAGE 2
"Service 'Apple Mobile Device Service' (Apple Mobile Device Service)
failed to start. Verify that you have sufficient permission to start system services"
SIDE NOTE
There was a USB cable connected to the PC to charge the iPhone,
but the iPhone was not connected. I detached the USB cable from the PC in case it's relevant.
(I did not reattach the USB cable until I finally got a copy of itunes to install. You will see later in this post below.).
I then clicked Retry.
ERROR MESSAGE 2 AGAIN
I received the identical 'Apple Mobile Device Service' error as above.
I then clicked Ignore.
iTunes > Status
> User Account Control pop-up window)
> Do you want to allow to install Apple iTunes>
Yes >
> Congratulations > Finish
> (iTunes pop-up error window):
> iTunes Helper
ERROR MESSAGE 3
a)
"Apple Application Support was not found.
Apple Application Support is required to run iTunes.
Please uninstall iTunes and install iTunes again.
Error 2 "
> (iTunes pop-up error window)
> iTunes
b)
"Apple Application Support was not found.
Apple Application Support is required to run iTunes.
Please uninstall iTunes and install iTunes again.
Error 2 (Windows Error 2)"
> OK > OK
ERROR MESSAGE 4
I received all of these errors above
when I had tried a fresh install before returning to the forum to search for answers.
When I had first tried a fresh install, I didn't get as far as the Congrats.
I only got as far as the first and second error listed above
("An error occurred during installation of assembly Microsoft VC80 CRT Type ="win32"...
AND Service 'Apple Mobile Device Service' (Apple Mobile Device Service").
Clicked on iTunes icon on desktop
ERROR MESSAGE 5
I receive the (iTunes pop-up error message window)
error 2 windows error 2 (identical to what's listed listed under 3b).
PART 2 - INSTALLATION RESOLUTION
The issue finally is resolved.
HERE IT IS!!!
1) Uninstall iTunes
2) check remaining Apple programs
(click control panel > programs > uninstall)
> check the listed Apple programs
Apple Application Support 32 bit,
Apple Mobile Device Support,
Apple Software Update,
Bonjour
3) Locate and save the correct file version of iTunes for your OS and System.
In my case, it's Win 7.
You must check for the System Type.
Computer > right click to properties > system type.
In my case its 64 bit.
The 32 bit installer is named iTunesSetup.exe,
while the 64 bit installer is named iTunes64Setup.exe.
I learned that some folks had experienced issues with
the 64 bit installer on the Apple site whether it's
because they had downloaded the 32 bit
when they needed the 64 and therefore
couldn't complete the install or in my case,
what appears to perhaps be a corrupted file that stated 6464 in the .exe file name.
This lead me to believe that finding the file with the correct file name and
correct file size to prove it authentic for that version would likely be part of
the solution if not the solution. File Hippo is one suggested means to locate the file.
I locate the iTunes download "iTunes64Setup.exe" that matched the size of the file
to a valid copy of that version of ITunes and I set it aside.
4) I then made sure that all old copies
and remnants of iTunes and Apple software
has been uninstalled by checking add/remove.
Then C: program files
and then C: program files (x86),
then running CC Cleaner,
then cleaning the registry using CC Cleaner
and then checking Tools under CC Cleaner.
***I discovered under Tools that there were remaining Apple files listed
after the uninstall of iTunes and other files had taken place under iTunes***
I visit tools under CC Cleaner and deleted the remaining Apple files
including Apple Application Support, Mobile Device Support, and Bonjour,
***but I leave the Apple Software Update folder as is, in tact***
under C: Program files (x86) and Tools of CC Cleaner and under Add/Remove.
5) I restart the computer, install the new copy of iTunes 12.1.1 (64 bit),
iTunes64Setup.exe, and it installed with zero errors.
Hope someone will find this useful. Good luck.

Try the "for older video cards" version.
For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down the page in case one of them applies.
The further information area has direct links to the current and recent builds in case you have problems downloading, need to revert to an older version or want to try the iTunes for Windows (64-bit - for older video cards) release as a workaround for installation or performance issues, or compatibility with QuickTime or third party software.
Your library should be unaffected by these steps but there are also links to backup and recovery advice should it be needed.
tt2

I have iTunes open in Windows XP and get an error 45048 message when I try to update apps thru the store. How can I fix this? I have reinstalled iTunes twice.

I have iTunes, latest version, open in Windows XP and get an error 45048 message when I try to update apps thru the store. How can I fix this? I have reinstalled iTunes twice but problem continues.

Try contacting iTunes via email to check if there is an issue with the account. go to apple.com/support/itunes
Click on iTunes Store account and billing and select inquiries. On the right side click on "email us".
Before doing that trying viewing your account information first. Open the iTunes on you mac, look at the menu and select store and select view my account. Try removing the card (this is only applicable if you don't have a pending charges with iTunes) and hit done. Sign out, quit iTunes and sign back in and try updating the apps again.

ITunes on Win 7 Pro won't recognise iPhone

iPhone 4 S is 12 months old next month.
OS is 7.0.2
iTunes vers is: 11.1.0.126
Computer OS is Win 7 Pro (anti virus is Microsoft Essentials, Firewall is ZoneAlarm)
I have manged to connect the phone to iTunes ... so there is a backup. However, that was a while ago and it's pot luck.
Even when I did connect it required several plugging and unplugging to get a connection.
NB - the computer is recognising the iPhone as I can d/load pictures from Photos and charge via the computer.
(As a clue: wall charge also requires often 6 plug in and out before it connects and begins charging so I use the computer mostly).
I've been through the list provided by Apple Help.
Also I remove Apple from devices so that it installs afresh.
And I have Stopped and Restarted Apple Mobile Device.
I have tried with firewall off (but when it did connect ages ago same firewall was on)
Unable to turn off MSE and really ought not have to uninstall.
So ... if you are into a techie challenge please take on my case.
No offence intended but not interested in amateur good ideas like "try another usb port" (have tried main and subsidiary port)....
I'm franly disappointed, frustrated and tired of the process but remain open to expert input.
thx for reading this post and should you offer expert advice then in advance may I thank you.
best wishes,

Never mind answering this question. I was able to figure out a way to fix the problem on my own. All I needed to do was install the Itunes update by itself and then I was able to open Itunes with no trouble.

Error 45048 - itunes - Win XP PRO

Similar Messages

Maybe you are looking for