Error 4900 while burning a cd.

Hello,
I have been trying to record a cd from my playlist,but everytime its about to finish, it displays a message error 4900 burning cd. I never experienced this before. I have a windows vista 64bit processor.
Does anyone has the same problem? Help
Thanks

yeha i do.. except sometimes it will say error 4000 or it will say error 4251
i jsut burned a cd last week i dont know why this is doing it

Similar Messages

I got an error message while burning a cd in itunes - "The attempt to burn a disc failed. The burn failed because of a medium write error. What is that and how can i fix it?t

I got an error message while burning a CD in iTunes - "the attempt to burn a disc failed. The burn failed because of a medium write error." What does this mean and how do I fix it?

The disk you are using probably has a defect, not uncommon on consumer grade disks. Try another disk or better yet another disk from a different manufacturer or at least a different batch.

An error occurred while burning the disc.

I tried to burn some stuff onto a DVD today with my PowerBook. Here's the info on the burner:
MATSHITA DVD-R UJ-845E:
Manufacturer: MATSHITA
Model: MATSHITA DVD-R UJ-845E
Revision: DMP2
Serial Number:
Drive Type: CD-RW/DVD-RW
Disc Burning: Apple Supported/Shipped
Removable Media: Yes
Detachable Drive: No
I bought some DVD's on sale at Radio Shack, and when I tried to burn a movie and a few photos onto a disc, the progress bar showed it starting to burn, then it stopped and I got this message:
"An error occurred while burning the disc. This disc cannot be used."
A little research here at the Apple forum brought me to this site:
http://www.digitalfaq.com/media/dvdmedia.htm
And after downloading a little program called DVD Media Inspector, I was able to classify the DVD's I had bought as:
"4TH CLASS MEDIA:
Pathetic garbage media, landfill material, about 0-50% success rate...."
OK, off to Mega Lo Mart, where I bought some nice, expensive Maxell DVD's.
Media Inspector doesn't see my fancy new DVD's. When I try to burn stuff using the Finder, I get the same result as before.
Getting desperate at that point, I located and downloaded updated firmware for my model of Matshita superdrive. I'm not sure what firmware is, and there was a free range one and a standard one, so I went for the standard one. There were dire warnings in the readme file about "flashing" a superdrive being on the same risk level as open heart surgery. I flashed my superdrive. (You can say that here, and it's not dirty.)
I also tried burning using iDVD, and after much preparation, it started to burn, then spit out the DVD. I tried three of the landfill DVD's and two of the Maxell ones. I'm out of things to try. Any ideas?
I have never tried burning DVD's before. Am I doing something wrong?

I tried again using iDVD's One-Step DVD making feature. It will let you make a one step from a movie file, and I had a .dv version of the movie I want to burn.
It encoded video for a while, encoded audio for a little while, then started to burn. The superdrive made some noises, then the DVD was ejected and I got an error message saying:
"Burning Finished
Errors were found during the burning process"
I hit OK (though it really wasn't OK) and got another error message box. This one said:
"Multiplexer error
(some message about multiplexing problem)"
The message didn't make sense to me, and I was unable to remember it. What's a multiplexer? I would have guessed an avid movie-goer, but somehow I think that is not it.

Error message while burning DVD with Premiere Elements 13 with Mac Book Pro i7/7200t/mn with 60GO free space available on gard drive. message: "erreur logicielle interne: DVA/premiere/elements/pre12/pre-mediacoreCS7". can someone help burn my DVD (the fil

Error message while burning DVD with Premiere Elements 13 with Mac Book Pro i7/7200t/mn with 60GO free space available on gard drive. message: "erreur logicielle interne: DVA/premiere/elements/pre12/pre-mediacoreCS7". can someone help burn my DVD (the file goes very well with chapters and scenes before burning). thanks very much, response appreciated, Alain

How to fix error 4450 while burning cd

how to fix error 4450 while burning cd

This error is usually the result of hacking (jailbreaking) the iPhone. It is likely now bricked.
Error 1015: This error is caused by attempts to downgrade the iPhone, iPad, or iPod touch's software. This can occur when you attempt to restore using an older .ipsw file. Downgrading to a previous version is not supported. To resolve this issue, attempt to restore with the latest iPhone, iPad, or iPod touch software available from Apple."

Error 4900 when burning

Hi
I just fixed the error 4280 from reading your support page but now when I try to burn I get failure due to error 4900, please help.
Kind regards

Hi
I just fixed the error 4280 from reading your support page but now when I try to burn I get failure due to error 4900, please help.
Here are my CD diagnostics
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
Sony Corporation VGN-S4M_S
iTunes 6.0.1.3
CD Driver 2.0.4.3
CD Driver DLL 2.0.3.2
LowerFilters: cdrbsdrv (7.5.0.0), AnyDVD (5.6.1.1), AFS2K (3.1.21.0), PXHELP20 (2.0.0.0),
UpperFilters: GEARAspiWDM (2.0.4.3),
Video Driver: NVIDIA GeForce Go 6200 \GeForce Go 6200
FlashMedia\MSorMSProDevice, Bus Type SSA
IDE\DiskFUJITSUMHT2060BH______________________40000049, Bus Type ATA, Bus Address [0,0]
IDE\CdRomMATSHITAUJ-832D________________________1.00___, Bus Type ATA, Bus Address [0,0]
SCSI\CdRomNERO___IMAGEDRIVE2____2.26, Bus Type SCSI, Bus Address [0,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
Current user is administrator.
F: MATSHITA UJ-832D, Rev 1.00
Media in drive is blank.
Get drive speed succeeded.
The drive CDR speeds are: 4.
The drive CDRW speeds are: 4.
The drive DVDR speeds are: 4 0 0.
The drive DVDRW speeds are: 4 0 0.
G: Unsupported CD or DVD drive.
Virtual drives can sometimes interfere with reading and writing CDs in iTunes. If this is a virtual drive and you are having problems with other drives, try uninstalling the virtual CD application.
Sony Vaio VGN-SM4/S Windows XP

Error 4850 while burning, after upgrading to 10.1.2.17

Hi guys I'm suddenly encountering error 4850 while trying to burn either an audio or mp3 CD. Burning a data cd seems to work fine. This just started happening I'm assuming because I upgraded to itunes 10.1.2.17, I've burned hundreds of CDs with no problem before the upgrade (altho I've had this problem once before after an upgrade about a year ago)
Any help would be greatly appreciated
Matt
Microsoft Windows 7 x64 Home Premium Edition (Build 7600)
HP-Pavilion AY747AA-ABA p6310y
iTunes 10.1.2.17
QuickTime 7.6.9
FairPlay 1.10.24
Apple Application Support 1.4.1
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.3.1.3
Apple Mobile Device Driver 1.52.0.0
Bonjour 2.0.3.0 (214.3)
Gracenote SDK 1.8.2.457
Gracenote MusicID 1.8.2.89
Gracenote Submit 1.8.2.123
Gracenote DSP 1.8.2.34
iTunes Serial Number F5BADCC543E06108
Current user is not an administrator.
The current local date and time is 2011-02-13 21:18:38.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
Video Display Information
NVIDIA, NVIDIA GeForce 9100
** External Plug-ins Information **
No external plug-ins installed.
iPodService 10.1.2.17 (x64) is currently running.
iTunesHelper 10.1.2.17 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
** CD/DVD Drive Tests **
No drivers in LowerFilters.
UpperFilters: GEARAspiWDM (2.2.0.1),
E: hp DVD-RAM GH40L, Rev RB0E
Audio CD in drive.
Found 16 songs on CD, playing time 60:07 on Audio CD.
Track 1, start time 00:02:00
Track 2, start time 03:56:37
Track 3, start time 07:23:20
Track 4, start time 10:57:07
Track 5, start time 14:31:25
Track 6, start time 19:12:65
Track 7, start time 22:06:67
Track 8, start time 25:46:05
Track 9, start time 29:34:67
Track 10, start time 33:38:65
Track 11, start time 37:11:05
Track 12, start time 40:46:20
Track 13, start time 44:25:10
Track 14, start time 48:04:62
Track 15, start time 52:17:05
Track 16, start time 56:39:35
Audio CD reading succeeded.
Get drive speed succeeded.
The drive CDR speeds are: 4 8 16 24 32 40.
The drive CDRW speeds are: 4.
The drive DVDR speeds are: 4.
The drive DVDRW speeds are: 4.
The last failed audio CD burn had error code 4850(0x000012f2). It happened on drive E: hp DVD-RAM GH40L on CDR media at speed 8X.

I am having the same error message displayed for my diagnostics run. Cannot burn any CD's. Is it even possible to burn CD's w/ iTunes?

Error -3 while burning cd

What does an -3 error mean while trying to burn to cd?

Did you resolve this problem?
edit: I tried burning songs, that I bought on Amazon and it worked. Whats wrong with the songs bought on Itunes?
Thx
Kai

Error -8785 while burning disc 2 of 3 during Back Up to Disc...

I regularly back up my iTunes library to DVD media-i hadn't done it in a few months and when I went to do so today using regular HP DVD+R discs that I've used before for this, the first disc burned fine (I needed three discs total, per iTunes). Discs 2 and 3 immediately failed with a -8785 error code. I restarted my MacBook Pro and used different discs, and keep getting the same thing. It looks like iTunes is fine with the first disc I burned as backup since it now says only two discs are required for the incremental backup. But I can't backup my iTunes library to disc (apart from, say, data discs). Disc 1 in this series, incidentally, was disc 30 for my collection, so I'd like to keep it going. I'm using iTunes 10, but I don't think that's the issue, since the first disc burned fine. Suggestions? Thanks.

I had the same, Error -8785, error while writing an MP3 CD. I found this post during a Google Search: http://lists.apple.com/archives/quicktime-api/2007/Apr/msg00110.html . Some of the names on the tracks, and the comments were very long, so I shortened them. Then it worked.
I hope this helps.
Regards, Nic

Error 4251 while burning to a disc

I keep getting an "Attempt to burn disc failed error 4251" message while trying to burn playlists to a disc. I've upgraded to the newest version of iTunes and tried using the lowest speed setting and the highest maximum to no avail. Any suggestions?

Not sure I can help very much, but I have had similar problems with large projects. I think (but I'm not sure) that iDVD does not do a very good job of estimating the size of the project until it starts to render/encode. So your project might be too big even for a dual-layer DVD. Can you reduce the size/length of the movie at all. And/or reduce the size of any iDVD slideshows you might also have in the iDVD project.
One small trick (I think this is true, but again I'm not 100% sure) is to reduce the size of the audio. If you use songs from iTunes, what format are they? I keep my songs in Apple Lossless which makes the files large. When I compress them to say AAC 128 or 160 in iTunes, and then use those smaller file versions in my iMovie project or slideshows, it reduces the size of the iDVD project.

Error 1951 while burning disc

I have been trying to burn a DVD-R of music but keep getting this error. I ran the diagnostics tool and it gave me this:
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
Dell Inc. Inspiron 9300
iTunes 7.3.1.3
CD Driver 2.0.6.1
CD Driver DLL 2.0.6.2
LowerFilters: PxHelp20 (2.0.0.0), AFS2K (3.1.20.0), PFC (2.5.0.204),
UpperFilters: GEARAspiWDM (2.0.6.1),
Current user is an administrator.
Video Display Information:
NVIDIA GeForce Go 6800
Connected Device Information:
Disk drive, TOSHIBA MK8026GAX, Bus Type ATA, Bus Address [0,0]
CD-ROM Drive, SONY DVD+-RW DW-D56A, Bus Type ATA, Bus Address [0,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
D: SONY DVD+-RW DW-D56A, Rev PDS7
Audio CD in drive.
Found 8 songs on CD, playing time 43:46 on Audio CD.
Track 1, start time 00:02:00
Track 2, start time 01:45:67
Track 3, start time 08:09:24
Track 4, start time 09:23:10
Track 5, start time 18:17:11
Track 6, start time 19:45:24
Track 7, start time 35:11:16
Track 8, start time 37:12:35
Audio CD reading succeeded.
Get drive speed succeeded.
The drive CDR speeds are: 24.
The drive CDRW speeds are: 24.
The drive DVDR speeds are: 24.
The drive DVDRW speeds are: 24.
Force Optical Power Calibration before burn is turned on in the preferences.
The last failed data CD or DVD burn had error code 1951(0x0000079f). It happened on drive D: SONY DVD+-RW DW-D56A on DVD+R media at speed 0X.

I had the same, Error -8785, error while writing an MP3 CD. I found this post during a Google Search: http://lists.apple.com/archives/quicktime-api/2007/Apr/msg00110.html . Some of the names on the tracks, and the comments were very long, so I shortened them. Then it worked.
I hope this helps.
Regards, Nic

Error 4900 When burning discs PLEASE HELP ME !!!

When i try burning a disc from itunes, after about a minute of doing stuff the disc ejects and i get a message saying there was an error burning the disc (4900)
This has only started happening the past couple of weeks, before that i never had any trouble burning discs from itunes atall.
It is very frustrating as i havent a clue what it means or what to do about it, can anyone help me fix it???
Please!!!!!!!!!!!!!!!!!

I just ran the diagnostics test and this is the results
Microsoft Windows Vista Home Edition Service Pack 1 (Build 6001)
Acer Aspire 5520
iTunes 8.0.1.11
QuickTime 7.5.5
FairPlay 1.0.15
CD Driver 2.0.7.5
CD Driver DLL 2.1.1.1
Apple Mobile Device 2.1.1.13
Bonjour 1.0.5.11 (118.5)
iTunes Serial Number 25042FB61CBEED6A
Current user is not an administrator.
The current local date and time is 2008-10-04 17:29:33.
iTunes is not running in safe mode.
Video Display Information
NVIDIA, NVIDIA GeForce 7000M / nForce 610M
** External Plug-ins Information **
No external plug-ins installed.
** Network Connectivity Tests **
Network Adapter Information
Adapter Name: {FB97CCED-8C3D-4788-9FD1-7EDF228EAD8D}
Description: Broadcom 802.11g Network Adapter
IP Address: 192.168.1.2
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
DHCP Enabled: Yes
DHCP Server: 192.168.1.1
Lease Obtained: Sat Oct 04 17:05:55 2008
Lease Expires: Sun Oct 05 17:05:55 2008
DNS Servers: 192.168.1.1
192.168.1.1
Adapter Name: {4A66390C-37F1-4179-AF6D-56BE200D52CB}
Description: NVIDIA nForce Networking Controller
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Thu Jan 01 00:00:00 1970
Lease Expires: Thu Jan 01 00:00:00 1970
DNS Servers:
Active Connection: LAN Connection
Connected: Yes
Online: Yes
Using Modem: No
Using LAN: Yes
Using Proxy: No
SSL 3.0 Support: Enabled
TLS 1.0 Support: Enabled
Firewall Information
Windows Firewall is on.
iTunes is enabled in Windows Firewall.
Connection attempt to Apple web site was successful.
Connection attempt to iTunes Store was successful.
Secure connection attempt to iTunes Store was successful.
Secure connection attempt to iPhone activation server was successful.
Last successful store access was 2008-09-26 09:39:17.
** CD/DVD Drive Tests **
LowerFilters: PxHelp20 (2.0.0.0),
UpperFilters: NTIDrvr (1.0.0.6), GEARAspiWDM (2.0.7.5),
E: MATSHITA DVD-RAM UJ870QJ, Rev 1.00
Audio CD in drive.
Audio CD reading succeeded.
Get drive speed succeeded.
The drive CDR speeds are: 4 8 12 16 24.
The drive CDRW speeds are: 4.
The drive DVDR speeds are: 4.
The drive DVDRW speeds are: 4.
The last failed audio CD burn had error code 4900(0x00001324). It happened on drive E: MATSHITA DVD-RAM UJ870QJ on CDR media at speed 24X.
** iPod/iPhone Connectivity Tests **
iPodService 8.0.1.11 is currently running.
iTunesHelper 8.0.1.11 is currently running.
Apple Mobile Device service 2.11.32.0 is currently running.
Universal Serial Bus Controllers:
Standard OpenHCD USB Host Controller. Device is working properly.
Standard Enhanced PCI to USB Host Controller. Device is working properly.
FireWire (IEEE 1394) Host Controllers:
RICOH OHCI Compliant IEEE 1394 Host Controller. Device is working properly.
Most Recent Device Not Currently Connected:
iPod nano (3rd Generation) running firmware version 1.1.3
Serial Number: 6U747640YXR

Unknown error 2130906112 while burning DVD in Premiere Elements

Hi am trying to burn a DVD using Premiere Elements 3.0. My computer will go through the lengthy process of attempting to burn the CD. At the very end, the drive pops the DVD out and I get a message that states: Unknown error 2130906112. I have burned successfully in the past, but am unable to now. I have tried to do this about 7 times with this specific project and have had no success. I have used two different types of DVD+R (Memorex and Verbatim). My project is approximately 56 minutes long. Any help and/or advice is greatly appreciated!!!!

Great news!
I just can't see which is highlighted while doing so. I think it has to do with the template I chose in Premiere Elements while designing the movie.
The lack of the Sub-picture Highlights (the official name for the indicators of which Button one has navigated to), could be caused by several things:
1.) the inability of the PS3 to adequately display them. Like I said earlier, most people, that I know, use the PS3's for BD playing. The specs. are different for those, as opposed to the DVD-specs. I just do not know about the PS3.
2.) could be a problem with the Template. Which one did you choose? I'll be glad to check it out (if PrE4 has it) and report any issues that I find. Did you modify this Template, say in Photoshop/PSElements? Could be that one of those modifications turned ON all Sub-picture Highlights.
3.) could be a problem with the "authoring" phase of the Project. This is after the editing, and is where one assembles the Assets (Menus, etc.) and does the navigation. As PrE is semi-automatic, it does most of this for the user, with little intervention. Still, there could be ways to accidently mess something up here, though it's highly unlikely. Now, in my authoring program, all is done by hand, so I have hundreds of opportunities to make a mess of a Project - PrE shields the user from most of these.
Now, to your questions:
Can I use the Img software for all burning projects including CDs?
Yes. You can do most forms of burning, including CD's (Audio, Video or Data), so long as you have the right types of files.
What is the best way to organize and store my video files?
This is the $64,000 question. So much depends on what one has, how they are likely to need to access them and what equipment they either own, or wish to purchase. I'll give you my scheme, though it might be overkill for you. Still, you can get an idea and are free to adapt any part of it for your needs.
I work with several types of Assets: original (or stock) still images, Captured (stock, or client-supplied) motion, Audio (original, stock or extracted from the previously mentioned motion Assets, Menus (Templates and original creations), Titles (same) and then my Projects.
I keep the originals on both a NAS (Networked Attached Storage) drive that is networked to all of my computers, and also on external storage HDD's. I also back up to DVD-Data discs. For Captured, original Video, I also store all tapes and do NOT overwrite/reuse any. I only work with Copies of any of the Assets (the Captures are probably the exception, as I have the tapes, should I need to re-Capture).
I use several media browsers to organize my Assets. I then locate those necessary for a Project, and create a folder structure for that Project. Copies of the Assets are placed in that folder structure, beneath the Project name. Again - these are Copies, in case something happens.
Depending on what I need to do, the Scratch Disks (set with Edit>Preferences) are usually kept within the Project's folder structure too. Same for Exports. As I use a different program to author DVD's (Adobe Encore), I create my Encore Project within this structure too. The files that I Export from PrPro (my NLE of choice), are the ones that I then Import into Encore for authoring the Project.
When done, I Archive the editing Project and also the Encore Project, to another external drive. I will always make one additional copy of my output DVD as a backup, as I can use ImgBurn, or another utility, to Copy DVD.
After all of this, I can then safely Delete my entire Project folder from the system. Remember, it contains no origianl Assets (other than Captured materail), as I have everything on the NAS, plus an external, plus the backup DVD-Data disc. Right now, I have about 30 1 - 2TB external HDD's that I use. Some are for backup, and some are to allow me to move my Projects between my laptop or my workstation.
Hope that this helps. As I said, it's probably overkill, but much of the work that I do is for clients. If they come back with a change, or a problem, I want to be able to help them immediately.
Good luck and good questions,
Hunt

Getiing error=50 while burning dvd

i keep getting an error =50 when using roxio while im burning a dvd of photos and little mvi files from my camera. i just finished burning one folder and that went well. but now im burning a different folder and as its encoding it stops and shows me this error. when i look it up it says this is usually an itunes error. how do i find out what is wrong with this folder? is it really a mac os x error=50 or is there a corrupt file in this folder?

Hi. Same problem with my new macbook.
Tried two RI-DISC 8x certified, same error.
Tried again with a lower quality PRINCO DVD 4x, with no errors, just a slowdown to 2x.
Tried with 2 Verbatim 16x cerified without "anomalies".
Tried finally once more with RI-DISC 8x : success
I guess the first 2 discs were damaged, maybe some scratches on them, and maybe the matshita unit on my macbook is a little bit "ticklish" , just to use an euphemism
iMac G5 20'' iSight - Macbook Core Duo 2,0Ghz Mac OS X (10.4.6) 10.4.7 now

Sense Code Error 31000 while burning DL DVD Encore CS5 Macbook Pro

While attempting to burn a Dual Layer DVD on my Macbook Pro I got this error: "Sense Code 31000" just before it started to burn.
I changed the burn speed, verified my laptop burns DVD+R DL discs. Any help is much appreciated. Must burn a master to duplicated 100 dvds by Friday. Thanks!

Hi,
Sense Code errors are hardware or blank media related.
Try to burn with other blank disc, if it does not work then the problem may be because of burner.
Thanks,
Pankaj Gauba

Error 4900 while burning a cd.

Similar Messages

Maybe you are looking for