Error 550 5.1.1 When inviting a resource using Outlook connector

We are get Undeliverable bounce back message when we invite resources to meetings in Outlook.
Your message did not reach some or all of the intended recipients.
Subject:     Test From Outlook
Sent:     1/15/2008 4:24 PM
The following recipient(s) could not be reached:
Test Resource on 1/15/2008 4:24 PM
The Sun SMTP Transport service failed to deliver the message to this recipient on server server.domain.com for the following reason: 550 5.1.1 unknown or illegal alias: [email protected]
But the meeting gets added to the resource calendar. We did not have this problem when we were testing but now that we have gone live it is annoying our users.
When resources are invited to meetings in UWC we do not get the SMTP error.
We are running Messaging server 6.3, Calendar Server 6.3, and Outlook connector 7.2.4
Thanks
Josh

Coolhands_99 wrote:
But the meeting gets added to the resource calendar. We did not have this problem when we were testing but now that we have gone live it is annoying our users. When you invite a resource with Outlook Connector, an email is sent to the value of the "mail:" attribute for the resource as well as having the event added to the resource calendar directly via WCAP. This is an MS Outlook specific behaviour.
Refer to the following link on how to have these emails automatically discarded by using a 'bitbucket' channel address:
http://docs.sun.com/app/docs/doc/819-5200/6n7a49o05?a=view
When resources are invited to meetings in UWC we do not get the SMTP error. UWC doesn't send an email to the "mail:" address.
Regards,
Shane.

Similar Messages

  • Email entering inbox as read when using Outlook Connector

    When using Outlook Connector (R 9.0.4.1) with Outlook 2003 all mail that is received has the header:
    'This message has not been sent.
    The message will be sent via Oracle Connector for Outlook.'
    All mail that is received is also marked as read.
    When Outlook connector is removed there is no problem.
    I haven't found any settings within Outlook that would help.
    Has anyone else experienced this problem, or have any ideas what is causing it?

    Hi,
    Don't know if you meant it literally, but OCFO only started supporting Outlook 2003 with 9.0.4.1.11, not 9.0.4.1. Perhaps this is part of the problem.
    Regards,
    Francois Perrault

  • Error Rounding Difference too high when reset cleared document using FBRA

    My Client has posted cleared document with T_Code F-51. This cleared document has cleared 6040 open items.
    And now, they want to reset and reverse that cleared document.
    We found error "Rounding difference too high" when we are reset cleared document using FBRA.
    Kindly need your advice.
    Many thanks in advance.
    Regards,

    Hello,
    Please let me know the ERROR number.
    Regards,
    Ravi

  • TS3991 When I try to use Outlook Setup for the iCloud on my PC I get an error message at step 2 of 7 Download Calender from iCloud as follows: "your setup couldn't be started because of an unexpected error"

    When I try to set up MS Outlook using Outlook Setup for Icloud it fails at step 2 of 7  Download Calender from iCloud with error message "your setup could not be started because of an unexpected error"  My iCloud calender in Outlook had previously been working, but was not reflecting the same scheduling information, so I tried to delete it and reinstall using the Outlook Setup for iCloud.
    How can I get it to work again?

    Hello, ksb2. 
    Thank you for visiting Apple Support Communities.
    We are investigating this issue. This article will be updated as more information becomes available.
    iCloud: iCloud Control Panel setup cannot be started
    http://support.apple.com/kb/TS5178
    Cheers,
    Jason H.

  • I have PSE on my Macbook Pro but get an 'error' listed as 150.30 when I try to use it. What is this error and how do I fix it?

    What is a 150.30 error when i try to use my PSE program on my Macbook Pro 2012 computer?  How do I fix it?

    Hi Dennis,
    Please follow this KB
    Error "Licensing has stopped working" | Mac OS
    Regards,
    Sandeep

  • When sending an email using outlook can you attach another email?

    When sending a new email using outlook, is it possible to attach another email?

    What does that have to do with iPhones?

  • Stops working when accessing hotmail account using outlook

    When I try to access my hotmail account using Outlook, I get a message that Nightly has stopped working. I don't have to take any action after logging into the account for this to happen and it happens every time. I can use yahoo mail with no problem.
    Application Basics
    Name: Firefox
    Version: 29.0a1
    User Agent: Mozilla/5.0 (Windows NT 6.3; Win64; x64; rv:29.0) Gecko/20100101 Firefox/29.0
    Crash Reports for the Last 3 Days
    All Crash Reports
    Extensions
    Important Modified Preferences
    accessibility.typeaheadfind.flashBar: 0
    browser.cache.disk.capacity: 358400
    browser.cache.disk.smart_size_cached_value: 358400
    browser.cache.disk.smart_size.first_run: false
    browser.cache.disk.smart_size.use_old_max: false
    browser.places.smartBookmarksVersion: 6
    browser.sessionstore.upgradeBackup.latestBuildID: 20140118030204
    browser.startup.homepage: http://xfinity.comcast.net/?cid=insDate07102013
    browser.startup.homepage_override.buildID: 20140118030204
    browser.startup.homepage_override.mstone: 29.0a1
    dom.mozApps.used: true
    dom.w3c_touch_events.expose: false
    extensions.lastAppVersion: 29.0a1
    gfx.direct3d.last_used_feature_level_idx: 0
    gfx.direct3d.prefer_10_1: true
    network.cookie.prefsMigrated: true
    places.database.lastMaintenance: 1390175426
    places.history.expiration.transient_current_max_pages: 104858
    plugin.disable_full_page_plugin_for_types: application/pdf
    plugin.importedState: true
    print.printer_Microsoft_XPS_Document_Writer.print_bgcolor: false
    print.printer_Microsoft_XPS_Document_Writer.print_bgimages: false
    print.printer_Microsoft_XPS_Document_Writer.print_colorspace:
    print.printer_Microsoft_XPS_Document_Writer.print_command:
    print.printer_Microsoft_XPS_Document_Writer.print_downloadfonts: false
    print.printer_Microsoft_XPS_Document_Writer.print_duplex: -2147483571
    print.printer_Microsoft_XPS_Document_Writer.print_edge_bottom: 0
    print.printer_Microsoft_XPS_Document_Writer.print_edge_left: 0
    print.printer_Microsoft_XPS_Document_Writer.print_edge_right: 0
    print.printer_Microsoft_XPS_Document_Writer.print_edge_top: 0
    print.printer_Microsoft_XPS_Document_Writer.print_evenpages: true
    print.printer_Microsoft_XPS_Document_Writer.print_footercenter:
    print.printer_Microsoft_XPS_Document_Writer.print_footerleft: &PT
    print.printer_Microsoft_XPS_Document_Writer.print_footerright: &D
    print.printer_Microsoft_XPS_Document_Writer.print_headercenter:
    print.printer_Microsoft_XPS_Document_Writer.print_headerleft: &T
    print.printer_Microsoft_XPS_Document_Writer.print_headerright: &U
    print.printer_Microsoft_XPS_Document_Writer.print_in_color: true
    print.printer_Microsoft_XPS_Document_Writer.print_margin_bottom: 0.5
    print.printer_Microsoft_XPS_Document_Writer.print_margin_left: 0.5
    print.printer_Microsoft_XPS_Document_Writer.print_margin_right: 0.5
    print.printer_Microsoft_XPS_Document_Writer.print_margin_top: 0.5
    print.printer_Microsoft_XPS_Document_Writer.print_oddpages: true
    print.printer_Microsoft_XPS_Document_Writer.print_orientation: 1
    print.printer_Microsoft_XPS_Document_Writer.print_page_delay: 50
    print.printer_Microsoft_XPS_Document_Writer.print_paper_data: 1
    print.printer_Microsoft_XPS_Document_Writer.print_paper_height: 11.00
    print.printer_Microsoft_XPS_Document_Writer.print_paper_name:
    print.printer_Microsoft_XPS_Document_Writer.print_paper_size_type: 0
    print.printer_Microsoft_XPS_Document_Writer.print_paper_size_unit: 0
    print.printer_Microsoft_XPS_Document_Writer.print_paper_width: 8.50
    print.printer_Microsoft_XPS_Document_Writer.print_plex_name:
    print.printer_Microsoft_XPS_Document_Writer.print_resolution: 1065353216
    print.printer_Microsoft_XPS_Document_Writer.print_resolution_name:
    print.printer_Microsoft_XPS_Document_Writer.print_reversed: false
    print.printer_Microsoft_XPS_Document_Writer.print_scaling: 1.00
    print.printer_Microsoft_XPS_Document_Writer.print_shrink_to_fit: false
    print.printer_Microsoft_XPS_Document_Writer.print_to_file: false
    print.printer_Microsoft_XPS_Document_Writer.print_unwriteable_margin_bottom: 0
    print.printer_Microsoft_XPS_Document_Writer.print_unwriteable_margin_left: 0
    print.printer_Microsoft_XPS_Document_Writer.print_unwriteable_margin_right: 0
    print.printer_Microsoft_XPS_Document_Writer.print_unwriteable_margin_top: 0
    print.printer_Samsung_ML-2010_Series.print_bgcolor: false
    print.printer_Samsung_ML-2010_Series.print_bgimages: false
    print.printer_Samsung_ML-2010_Series.print_colorspace:
    print.printer_Samsung_ML-2010_Series.print_command:
    print.printer_Samsung_ML-2010_Series.print_downloadfonts: false
    print.printer_Samsung_ML-2010_Series.print_duplex: -2147483571
    print.printer_Samsung_ML-2010_Series.print_edge_bottom: 0
    print.printer_Samsung_ML-2010_Series.print_edge_left: 0
    print.printer_Samsung_ML-2010_Series.print_edge_right: 0
    print.printer_Samsung_ML-2010_Series.print_edge_top: 0
    print.printer_Samsung_ML-2010_Series.print_evenpages: true
    print.printer_Samsung_ML-2010_Series.print_footercenter:
    print.printer_Samsung_ML-2010_Series.print_footerleft: &PT
    print.printer_Samsung_ML-2010_Series.print_footerright: &D
    print.printer_Samsung_ML-2010_Series.print_headercenter:
    print.printer_Samsung_ML-2010_Series.print_headerleft: &T
    print.printer_Samsung_ML-2010_Series.print_headerright: &U
    print.printer_Samsung_ML-2010_Series.print_in_color: true
    print.printer_Samsung_ML-2010_Series.print_margin_bottom: 0.5
    print.printer_Samsung_ML-2010_Series.print_margin_left: 0.5
    print.printer_Samsung_ML-2010_Series.print_margin_right: 0.5
    print.printer_Samsung_ML-2010_Series.print_margin_top: 0.5
    print.printer_Samsung_ML-2010_Series.print_oddpages: true
    print.printer_Samsung_ML-2010_Series.print_orientation: 1
    print.printer_Samsung_ML-2010_Series.print_page_delay: 50
    print.printer_Samsung_ML-2010_Series.print_paper_data: 1
    print.printer_Samsung_ML-2010_Series.print_paper_height: 11.00
    print.printer_Samsung_ML-2010_Series.print_paper_name:
    print.printer_Samsung_ML-2010_Series.print_paper_size_type: 0
    print.printer_Samsung_ML-2010_Series.print_paper_size_unit: 0
    print.printer_Samsung_ML-2010_Series.print_paper_width: 8.50
    print.printer_Samsung_ML-2010_Series.print_plex_name:
    print.printer_Samsung_ML-2010_Series.print_resolution: 1065353216
    print.printer_Samsung_ML-2010_Series.print_resolution_name:
    print.printer_Samsung_ML-2010_Series.print_reversed: false
    print.printer_Samsung_ML-2010_Series.print_scaling: 1.00
    print.printer_Samsung_ML-2010_Series.print_shrink_to_fit: false
    print.printer_Samsung_ML-2010_Series.print_to_file: false
    print.printer_Samsung_ML-2010_Series.print_unwriteable_margin_bottom: 0
    print.printer_Samsung_ML-2010_Series.print_unwriteable_margin_left: 0
    print.printer_Samsung_ML-2010_Series.print_unwriteable_margin_right: 0
    print.printer_Samsung_ML-2010_Series.print_unwriteable_margin_top: 0
    privacy.sanitize.migrateFx3Prefs: true
    storage.vacuum.last.index: 1
    storage.vacuum.last.places.sqlite: 1389307622
    Graphics
    Adapter Description: Intel(R) HD Graphics 4000
    Adapter Drivers: igdumdim64 igd10iumd64 igd10iumd64 igdumdim32 igd10iumd32 igd10iumd32
    Adapter RAM: Unknown
    Device ID: 0x0166
    Direct2D Enabled: true
    DirectWrite Enabled: true (6.3.9600.16384)
    Driver Date: 10-1-2013
    Driver Version: 10.18.10.3316
    GPU #2 Active: false
    GPU Accelerated Windows: 1/1 Direct3D 10
    Vendor ID: 0x8086
    WebGL Renderer: Google Inc. -- ANGLE (Intel(R) HD Graphics 4000 Direct3D9Ex vs_3_0 ps_3_0)
    windowLayerManagerRemote: false
    AzureCanvasBackend: direct2d
    AzureContentBackend: direct2d
    AzureFallbackCanvasBackend: cairo
    AzureSkiaAccelerated: 0
    JavaScript
    Incremental GC: true
    Accessibility
    Activated: false
    Prevent Accessibility: 0
    Library Versions
    NSPR
    Expected minimum version: 4.10.3 Beta
    Version in use: 4.10.3 Beta
    NSS
    Expected minimum version: 3.15.5 Basic ECC Beta
    Version in use: 3.15.5 Basic ECC Beta
    NSSSMIME
    Expected minimum version: 3.15.5 Basic ECC Beta
    Version in use: 3.15.5 Basic ECC Beta
    NSSSSL
    Expected minimum version: 3.15.5 Basic ECC Beta
    Version in use: 3.15.5 Basic ECC Beta
    NSSUTIL
    Expected minimum version: 3.15.5 Beta
    Version in use: 3.15.5 Beta

    How do you get the message:
    * Firefox crash dialog
    * (NOT RESPONDING) on the window title bar
    * Windows dialog
    Could you try the site in Firefox's Safe Mode? That's a standard diagnostic tool to bypass interference by extensions, disable hardware acceleration of graphics, disable the JavaScript compilers, and disable some custom settings. More info: [[Troubleshoot Firefox issues using Safe Mode]].
    You can restart Firefox in Safe Mode using
    Help > Restart with Add-ons Disabled
    In the dialog, click "Start in Safe Mode" (''not'' Reset)
    Any difference?

  • Error for creating a view, when I try to use a specific schema

    Hi,
    I have a query which has some UNION ALL statements.
    select a, b, c, ad_spend from tbl a
    union all
    select a, b, c, ad_spend from tbl b
    union all
    select a, b, c, ad_spend from tbl c where ad_spend > 10
    When I try to run the above query, it runs perfectly fine.
    When I embed the above query to a view i.e.,
    CREATE VIEW vw_test
    as
    select .....
    The above view is also working fine.
    But I have a schema in the database as "rpt". I want to create view as "rpt.vw_test".
    When I try to create view like that, it shows me an error
    Msg 209, Level 16, State 1, Procedure Combined, Line 307
    Ambiguous column name 'ad_spend'.
    Note: ad_spend is a column in all 3 tables.When I run the queries individually, it gets successfully executed.
    Can you please let me know how to resolve this.
    Thanks,
    Raksha

    Raksha,
    This error has to do something with the compiler unable to nderstand which column to bound from a set of tables having the same column among them. Usage of alias names for the tables and using the correspoonding alias names in the where clause or join conditions
    as well should help.
    For further info/examples refer:
    http://databases.aspfaq.com/database/what-does-ambiguous-column-name-mean.html
    http://www.sql-server-helper.com/error-messages/msg-209.aspx
    If you want more help, we can do so only witht he query. Try posting the query :)
    Edited:
    The missing UNION is to be fixed first as mentioned by Mr.Dimant. Even after that if the error persists you can refer my above solution
    Thanks,
    Jay
    <If the post was helpful mark as 'Helpful' and if the post answered your query, mark as 'Answered'>

  • Receiving error when trying to combine using Outlook 2013

    When using the combine function, dragging and dropping emails from outlook 2013 is not working properly. It allows you to drag and then drop them but the combine is unsuccessful.  Has anyone else experienced this issue and know how ot fix it?

    1.       She had Acrobat X and when that did not work, I installed Acrobat XI to test.  So I can rollback to X but that was not working.
    2.
    3.       Everything seems to work except emails that are drag and dropped
    4.       I have done a repair and uninstall/reinstall
    Kelly H. Fields | Technical Support Analyst
    Desktop Services | Information Technology
    Aflac Worldwide Headquarters
    Tel: 706.243.8445<tel:706.243.8445> | Fax: 706.596.3072<tel:706.596.3072>
    1932 Wynnton Road, Columbus, Georgia 31999
    [email protected]<mailto:[email protected]> | aflac.com<http://aflac.com/>
    • A Fortune 500 Company
    • Fortune’s Best Companies to Work For
    • Fortune’s Most Admired Companies

  • I purchased MS Office for my MacBook Air. It included Outlook. When I try to use Outlook, it tells me that I need to purchase an upgrade. What is the deal?

    I purchased MS Office for my MacBook Air.  It included Outlook.  When I click on Outlook, I get a message telling me I need to upgrade and buy MS Office. I don't understand.  Please help.

    You bought MS Office Home and Student, it does not include a license for Outlook.
    You have to pay for Outlook.

  • Can't Sync Outlook Calander with Curve 9300 when using Outlook Connector

    Sorry I know there is a simple answer but I can't find it.  I use Outlook 2010 with my hotmail account using hotmail connector.  The calander will not sync and the message I get is "Unable to access local folders.  If your Outlook profile uses Hotmail connector, you must create a local data store (PST) and set it as the default delivery location for the profile".  I simply do not understand what this means and how I do it.  Please help? 

    Hi Paul111000 and welcome to the BlackBerry Support Community Forums!
    Windows Live™ Hotmail® connector is not supported for synchronization with the BlackBerry® Desktop Software.
    Thanks.
    -CptS
    Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
    Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

  • Error 550 while using windows terminal mode

      I am using the GPIB-RS232 converter
      I am NOT using LabView.  I am attempting to use it with an RS232 interface via a standard terminal program.
      I am testing the setup with an HP(Agilent) 34401A meter
      If I enter the following via the terminal:
    Wrt 22
    *cls
    Wrt 22
    *rst
    Wrt 22
    Conf:volt:dc 100, 0.003
      Everything is fine and the meter goes in the proper mode.
      If I enter:
    Wrt 22
    Meas?
      Or
    Wrt 22
    Read?
      The meter reports Error code 550:
    From the HP manual:
    "The multimeter received a READ? or MEASure? command while in the local mode. During RS-232 operation, you should always execute the SYSTem:REMote command before sending other commands over the interface."
    SYSTem:REMote is an RS232 command and is not available when utilizing the GPIB interface.
    From the HP site
    This RS-232 error 550 can be generated when using a non-Agilent controller to program the DVM over the GP-IB. The error usually occurs when performing a query (MEAS: ? or READ?). We have seen the problem occur with a National Instruments and a Metro-byte(sp?) 488 card.
    This error occurs when the non-Agilent controllers sends commands to instruments, without pulling the REMOTE line on the GP-IB interface. The IEEE 488.2 specification requires the instrument to be in remote mode, when performing a query. The fixes is to set a bit on the card to force the REMOTE line true.
    Something is wrong with how your GP-IB card is setup, please contact the manufacturer of your GP-IB card on how assert the REMOTE line.
    Solutions or suggestions appreciated.
    Phil

    Phil,
    There is a special remote enable command for using the serial to gpib converter. You need to send "sre" command to enable the Remote Enable line. Here is the info from the GPIB-serial converter help file:
    sre
    Set (or Clear) Remote Enable
    Type
    Low-level bus management function
    Syntax
    sre
    [bool]<CR>
    Purpose
    Use sre to turn the Remote Enable
    signal on and off. In some cases, the first I/O or high-level bus management
    function you call sets remote enable automatically.
    Remarks
    If the argument bool is 1, the GPIB-RS232/485/422 asserts the Remote Enable
    (REN*) signal. If the argument bool is 0, the GPIB-RS232/485/422 unasserts REN*.
    Many GPIB devices have a remote program mode and a local program
    mode. It is usually necessary to place devices in remote mode before programming
    them from the GPIB. A device enters the remote mode when the REN* line is
    asserted and the device receives its listen address.
    Use cmd to send a device its listen
    address after using sre. Use loc to return the device to local program mode.
    If you call sre with an argument and
    the GPIB-RS232/485/422 is not System Controller, the ESAC error is recorded.
    If you call sre without an argument,
    the GPIB-RS232/485/422 returns its current remote status: 1 = remote, 0 = local.
    -Marshall R
    National Instruments
    Applications Engineer
    One stop for all your NI-VISA Support
    GPIB Support has a new homepage

  • Error 550 when using CFFTP to remove a file

    I'm using cfftp to download files which I parse, then I need to delete the file from the server. (coldfusion 11 - development)
    I can list, and download the files fine, but am butting my head into a problem that I can't seem to resolve.
    USING THE SAME PATH AND FILE NAME that allowed me to 'get' the file - When I try to remove the file - I get this error.
    Error: 550 file: No such file or directory .
    (again - the path and file name I provide are identical to the path/filename -
    if this is a permission problem, I can delete files thru Filezilla, using the same credentials - with no problem)
    Here is the call to remove -
        <cfftp  action="remove"
                connection="myConnection1"
                passive="true"
                timeout="360"
                remotefile="#myPath##fileName#"
                item="file" >

    I'm not sure where you got the "This is not what the docs say" part.  Looking down the list of CFFTP attributes in the CF11 docs that apply to a "remove" operation, those were the attributes I would have expected to need.  Although I agree the examples could be clearer and a specific example of removing a file would be useful.
    -Carl V.

  • Receiving Error 550 when using Exchange via another software application.

    Here's a good one (and I hope I'm able to explain this correctly)....
    I work at a hospital where we have a gym facility that is open to employees and also to the public.  We use a client management system called Twin Oaks.  This Twin Oaks software has email functionality that uses an Exchange user account to send
    group emails out to clients (this avoids the front desk staffers from having to create email distro groups in Outlook to send out mass emails).
    I worked with the Twin Oaks support staff to get the email integration set up with our Exchange server (it was an easy process, entering the SMTP server name then a few other basic settings).
    Emailing through the Twin Oaks software works, but only to clients who have INTERNAL hospital email addresses.  The messages are failing to go out to any client that has an external email address (Error 550 states the address is unavailable).
    Twin Oaks' response to this is that we have some type of firewall that is preventing the delivery of these emails to external addresses.  This is not the case and I can't seem to find any reason that would prevent the mails from going out.  We
    can email external addresses direct from the generic account we set up for this purpose, but for some reason, the mails are not going when they are sent through Twin Oaks application.  
    We are using Exchange Server 2010.  I can't find any transport settings or policies that would prevent emails from going to external addresses and am stumped as to why this isn't working.  
    Has anyone else experienced these types of issues when using Exchange through another software application to send messages?
    Any responses would be greatly appreciated!

    Hi,
    Based on the description, you could send email to external addresses without the Twin Oaks software. However, with the Twin Oaks software, you couldn't send successfully.
    For this issue, I recommend you enable message tracking and check whether you could retrieve message tracking log entires when you send emails to external addresses through the Twin Oaks software.
    If you couldn't retrieve message these tracking log entires when you send emails to external addresses through the Twin Oaks software, it means that the Exchange server is OK and the crux of the problem is the Twin Oaks software.
    Here is an article about message tracking log for your reference.
    Get-MessageTrackingLog
    http://technet.microsoft.com/en-us/library/aa997573(v=exchg.141).aspx
    Best regards,
    Belinda
    Belinda Ma
    TechNet Community Support

  • Communication error, user "did not accept your invitation"

    I think need some help. I have read many of the topics, however i have not been able to address my issue. Let me start by saying I am new to Macs (about 3 weeks) and not very technical. I have a Imac and also running time capsule as my wireless connection. As instructed i obtained an AIM account and attempted to do video chat, however when I try i get a communication error, user "did not accept your invitation". I have spent about an hour with apple tech services and have been able to successfully connect to the Apple test buddy. In fact my friend was also able to connect to the Apple test buddy. I have not tested a connection with anyone else.
    I would greatly appreciate any help with this issue.

    Hi Thank you for responding,
    The message says that there was a communication error - did not receive response from the other person. On the other side they received the same error. Below is the error log
    Yes, Time Capsule sits between my modem and my computer. I also have a Voice over Internet phone.
    The entire set up is as follows.
    Internet modem (make; Ambit) to Voice over Internet Modem to Time Capsule (set as router - share a single IP address using DHCP & NAT)
    as for setting up time capsule - i set it to "i don't have a wireless network and wanted to create one"
    I have not attempted to reach anyone in table 2 - I will do so and let you know
    my error log -- again thanks for your help
    Date/Time: 2008-03-27 20:46:00.255 -0400
    OS Version: 10.5.2 (Build 9C7010)
    Report Version: 4
    iChat Connection Log:
    2008-03-27 20:45:25 -0400: AVChat started with ID 2073701542.
    2008-03-27 20:45:25 -0400: loopie5331: State change from AVChatNoState to AVChatStateWaiting.
    2008-03-27 20:45:25 -0400: 0x14ae87f0: State change from AVChatNoState to AVChatStateInvited.
    2008-03-27 20:45:35 -0400: 0x14ae87f0: State change from AVChatStateInvited to AVChatStateConnecting.
    2008-03-27 20:45:35 -0400: loopie5331: State change from AVChatStateWaiting to AVChatStateConnecting.
    2008-03-27 20:45:55 -0400: 0x14ae87f0: State change from AVChatStateConnecting to AVChatStateEnded.
    2008-03-27 20:45:55 -0400: 0x14ae87f0: Error -8 (Did not receive a response from 0x14ae87f0.)
    2008-03-27 20:45:55 -0400: loopie5331: State change from AVChatStateConnecting to AVChatStateEnded.
    2008-03-27 20:45:55 -0400: loopie5331: Error -8 (Did not receive a response from 0x14ae87f0.)
    Video Conference Error Report:
    17.607834 @SIP/SIP.c:2719 type=4 (900A0015/0)
    [SIPConnectIPPort failed]
    19.608154 @SIP/SIP.c:2719 type=4 (900A0015/0)
    [SIPConnectIPPort failed]
    Video Conference Support Report:
    0.523429 @Video Conference/VCInitiateConference.m:1582 type=2 (00000000/0)
    [Connection Data for call id: 1 returns 1
    9.592914 @Video Conference/VCInitiateConference.m:1597 type=2 (00000000/0)
    [Prepare Connection With Remote Data - remote VCConnectionData: 1, local VCConnectionData: 1
    9.600060 @Video Conference/VCInitiateConference.m:1701 type=2 (00000000/0)
    [Initiate Conference To User: u0 with Remote VCConnectionData: 1 with Local Connection Data: 1 conferenceSettings: 1]
    15.607906 @SIP/Transport.c:2362 type=1 (00000000/0)
    [INVITE sip:user@rip:16402 SIP/2.0
    Via: SIP/2.0/UDP lip:16402;branch=z9hG4bK5e75a87f218371dd
    Max-Forwards: 70
    To: "u0" <sip:user@rip:16402>
    From: "0" <sip:user@lip:16402>;tag=300068541
    Call-ID: 4a78f1f6-fc60-11dc-80cb-9299630c4012@lip
    CSeq: 1 INVITE
    Contact: <sip:user@lip:16402>;isfocus
    User-Agent: Viceroy 1.3
    Content-Type: application/sdp
    Content-Length: 731
    v=0
    o=Aldo 0 0 IN IP4 lip
    s=0
    c=IN IP4 lip
    b=AS:2147483647
    t=0 0
    a=hwi:1056:2:2800
    a=iChatEncryption:NO
    a=bandwidthDetection:YES
    m=audio 16402 RTP/AVP 110 121 12 3 0
    a=rtcp:16402
    a=rtpmap:121 speex/16000
    a=rtpmap:122 speex/8000
    a=rtpmap:113 X-AAC_LD/44100
    a=rtpmap:110 X-AAC_LD/22050
    a=rtpmap:3 GSM/8000
    a=rtpmap:0 PCMU/8000
    a=rtpID:3538228969
    m=video 16402 RTP/AVP 123 126 34
    a=rtcp:16402
    a=rtpmap:123 H264/90000
    a=rtpmap:126 X-H264/90000
    a=rtpmap:34 H263/90000
    a=fmtp:34 imagesize 1 rules 30:352:288
    a=framerate:30
    a=RTCP:AUDIO 16402 VIDEO 16402
    a=fmtp:126 imagesize 0 rules 20:640:480:640:480:20
    a=fmtp:123 imagesize 0 rules 20:640:480:640:480:20
    a=rtpID:1659256788
    16.108265 @SIP/Transport.c:2362 type=1 (00000000/0)
    [INVITE sip:user@rip:16402 SIP/2.0
    Via: SIP/2.0/UDP lip:16402;branch=z9hG4bK5e75a87f218371dd
    Max-Forwards: 70
    To: "u0" <sip:user@rip:16402>
    From: "0" <sip:user@lip:16402>;tag=300068541
    Call-ID: 4a78f1f6-fc60-11dc-80cb-9299630c4012@lip
    CSeq: 1 INVITE
    Contact: <sip:user@lip:16402>;isfocus
    User-Agent: Viceroy 1.3
    Content-Type: application/sdp
    Content-Length: 731
    v=0
    o=Aldo 0 0 IN IP4 lip
    s=0
    c=IN IP4 lip
    b=AS:2147483647
    t=0 0
    a=hwi:1056:2:2800
    a=iChatEncryption:NO
    a=bandwidthDetection:YES
    m=audio 16402 RTP/AVP 110 121 12 3 0
    a=rtcp:16402
    a=rtpmap:121 speex/16000
    a=rtpmap:122 speex/8000
    a=rtpmap:113 X-AAC_LD/44100
    a=rtpmap:110 X-AAC_LD/22050
    a=rtpmap:3 GSM/8000
    a=rtpmap:0 PCMU/8000
    a=rtpID:3538228969
    m=video 16402 RTP/AVP 123 126 34
    a=rtcp:16402
    a=rtpmap:123 H264/90000
    a=rtpmap:126 X-H264/90000
    a=rtpmap:34 H263/90000
    a=fmtp:34 imagesize 1 rules 30:352:288
    a=framerate:30
    a=RTCP:AUDIO 16402 VIDEO 16402
    a=fmtp:126 imagesize 0 rules 20:640:480:640:480:20
    a=fmtp:123 imagesize 0 rules 20:640:480:640:480:20
    a=rtpID:1659256788
    17.108616 @SIP/Transport.c:2362 type=1 (00000000/0)
    [INVITE sip:user@rip:16402 SIP/2.0
    Via: SIP/2.0/UDP lip:16402;branch=z9hG4bK5e75a87f218371dd
    Max-Forwards: 70
    To: "u0" <sip:user@rip:16402>
    From: "0" <sip:user@lip:16402>;tag=300068541
    Call-ID: 4a78f1f6-fc60-11dc-80cb-9299630c4012@lip
    CSeq: 1 INVITE
    Contact: <sip:user@lip:16402>;isfocus
    User-Agent: Viceroy 1.3
    Content-Type: application/sdp
    Content-Length: 731
    v=0
    o=Aldo 0 0 IN IP4 lip
    s=0
    c=IN IP4 lip
    b=AS:2147483647
    t=0 0
    a=hwi:1056:2:2800
    a=iChatEncryption:NO
    a=bandwidthDetection:YES
    m=audio 16402 RTP/AVP 110 121 12 3 0
    a=rtcp:16402
    a=rtpmap:121 speex/16000
    a=rtpmap:122 speex/8000
    a=rtpmap:113 X-AAC_LD/44100
    a=rtpmap:110 X-AAC_LD/22050
    a=rtpmap:3 GSM/8000
    a=rtpmap:0 PCMU/8000
    a=rtpID:3538228969
    m=video 16402 RTP/AVP 123 126 34
    a=rtcp:16402
    a=rtpmap:123 H264/90000
    a=rtpmap:126 X-H264/90000
    a=rtpmap:34 H263/90000
    a=fmtp:34 imagesize 1 rules 30:352:288
    a=framerate:30
    a=RTCP:AUDIO 16402 VIDEO 16402
    a=fmtp:126 imagesize 0 rules 20:640:480:640:480:20
    a=fmtp:123 imagesize 0 rules 20:640:480:640:480:20
    a=rtpID:1659256788
    17.608293 @SIP/Transport.c:2362 type=1 (00000000/0)
    [INVITE sip:user@rip:16402 SIP/2.0
    Via: SIP/2.0/UDP sip:32768;branch=z9hG4bK757dcfb6358328fd
    Max-Forwards: 70
    To: "u0" <sip:user@rip:16402>
    From: "0" <sip:user@lip:16402>;tag=2081639093
    Call-ID: 4baa518c-fc60-11dc-80cb-ea4e74ce4012@lip
    CSeq: 1 INVITE
    Contact: <sip:user@sip:32768>;isfocus
    User-Agent: Viceroy 1.3
    Content-Type: application/sdp
    Content-Length: 725
    v=0
    o=Aldo 0 0 IN IP4 sip
    s=0
    c=IN IP4 sip
    b=AS:2147483647
    t=0 0
    a=hwi:1056:2:2800
    a=iChatEncryption:NO
    a=bandwidthDetection:YES
    m=audio 32768 RTP/AVP 110 121 12 3 0
    a=rtcp:32768
    a=rtpmap:121 speex/16000
    a=rtpmap:122 speex/8000
    a=rtpmap:113 X-AAC_LD/44100
    a=rtpmap:110 X-AAC_LD/22050
    a=rtpmap:3 GSM/8000
    a=rtpmap:0 PCMU/8000
    a=rtpID:3538228969
    m=video 32768 RTP/AVP 123 126 34
    a=rtcp:32768
    a=rtpmap:123 H264/90000
    a=rtpmap:126 X-H264/90000
    a=rtpmap:34 H263/90000
    a=fmtp:34 imagesize 1 rules 30:352:288
    a=framerate:30
    a=RTCP:AUDIO 32768 VIDEO 32768
    a=fmtp:126 imagesize 0 rules 20:640:480:640:480:20
    a=fmtp:123 imagesize 0 rules 20:640:480:640:480:20
    a=rtpID:1659256788
    18.108636 @SIP/Transport.c:2362 type=1 (00000000/0)
    [INVITE sip:user@rip:16402 SIP/2.0
    Via: SIP/2.0/UDP sip:32768;branch=z9hG4bK757dcfb6358328fd
    Max-Forwards: 70
    To: "u0" <sip:user@rip:16402>
    From: "0" <sip:user@lip:16402>;tag=2081639093
    Call-ID: 4baa518c-fc60-11dc-80cb-ea4e74ce4012@lip
    CSeq: 1 INVITE
    Contact: <sip:user@sip:32768>;isfocus
    User-Agent: Viceroy 1.3
    Content-Type: application/sdp
    Content-Length: 725
    v=0
    o=Aldo 0 0 IN IP4 sip
    s=0
    c=IN IP4 sip
    b=AS:2147483647
    t=0 0
    a=hwi:1056:2:2800
    a=iChatEncryption:NO
    a=bandwidthDetection:YES
    m=audio 32768 RTP/AVP 110 121 12 3 0
    a=rtcp:32768
    a=rtpmap:121 speex/16000
    a=rtpmap:122 speex/8000
    a=rtpmap:113 X-AAC_LD/44100
    a=rtpmap:110 X-AAC_LD/22050
    a=rtpmap:3 GSM/8000
    a=rtpmap:0 PCMU/8000
    a=rtpID:3538228969
    m=video 32768 RTP/AVP 123 126 34
    a=rtcp:32768
    a=rtpmap:123 H264/90000
    a=rtpmap:126 X-H264/90000
    a=rtpmap:34 H263/90000
    a=fmtp:34 imagesize 1 rules 30:352:288
    a=framerate:30
    a=RTCP:AUDIO 32768 VIDEO 32768
    a=fmtp:126 imagesize 0 rules 20:640:480:640:480:20
    a=fmtp:123 imagesize 0 rules 20:640:480:640:480:20
    a=rtpID:1659256788
    19.108980 @SIP/Transport.c:2362 type=1 (00000000/0)
    [INVITE sip:user@rip:16402 SIP/2.0
    Via: SIP/2.0/UDP sip:32768;branch=z9hG4bK757dcfb6358328fd
    Max-Forwards: 70
    To: "u0" <sip:user@rip:16402>
    From: "0" <sip:user@lip:16402>;tag=2081639093
    Call-ID: 4baa518c-fc60-11dc-80cb-ea4e74ce4012@lip
    CSeq: 1 INVITE
    Contact: <sip:user@sip:32768>;isfocus
    User-Agent: Viceroy 1.3
    Content-Type: application/sdp
    Content-Length: 725
    v=0
    o=Aldo 0 0 IN IP4 sip
    s=0
    c=IN IP4 sip
    b=AS:2147483647
    t=0 0
    a=hwi:1056:2:2800
    a=iChatEncryption:NO
    a=bandwidthDetection:YES
    m=audio 32768 RTP/AVP 110 121 12 3 0
    a=rtcp:32768
    a=rtpmap:121 speex/16000
    a=rtpmap:122 speex/8000
    a=rtpmap:113 X-AAC_LD/44100
    a=rtpmap:110 X-AAC_LD/22050
    a=rtpmap:3 GSM/8000
    a=rtpmap:0 PCMU/8000
    a=rtpID:3538228969
    m=video 32768 RTP/AVP 123 126 34
    a=rtcp:32768
    a=rtpmap:123 H264/90000
    a=rtpmap:126 X-H264/90000
    a=rtpmap:34 H263/90000
    a=fmtp:34 imagesize 1 rules 30:352:288
    a=framerate:30
    a=RTCP:AUDIO 32768 VIDEO 32768
    a=fmtp:126 imagesize 0 rules 20:640:480:640:480:20
    a=fmtp:123 imagesize 0 rules 20:640:480:640:480:20
    a=rtpID:1659256788
    Video Conference User Report:
    0.000000 @:0 type=5 (00000000/16402)
    [Local SIP port]
    19.715397 @Video Conference/VideoConferenceMultiController.m:1474 type=5 (00000000/0)
    [IP And Port Data With Caller IP And Port Data: Obtained 120 bytes of local IP and port data (3 entries). Remote data was 0 bytes (0 entries).
    B
    Message was edited by: aldoz

Maybe you are looking for

  • Need help to open and look for file by name

    Hi,         Im needing help to open a folder and look for a file (.txt) on this directory by his name ... The user ll type the partial name of file , and i need look for this file on the folder , and delete it .... How can i look for the file by his

  • Getting wrong characters in PSE 8 (Mac OSX)

    I think my problem is best described by reference to these two sample galleries: Old gallery (PSE 2.0, Mac OS X.4): http://www.huthyfs.com/axes Note that é, e-acute, (images 2,3,4) is propery represented. New gallery, same images (PSE 8.0, Mac OS X.6

  • "Create Archive of" file destination

    Very strange- on my computer, when I control-click a folder and choose "Create Archive of-", the resulting .zip file ends up in the same folder as the original. I've just been helping my girlfriend archive some old files, and on her computer, the .zi

  • CL_WD_RUNTIME_SERVICES= ATTACH_FILE_TO_RESPONSE( ) works in one system but does not in other

    Hi folks, We are facing an issue here with a custom web dynpro application that export an excel. The following piece of code has been written in this application to export an excel: cl_wd_runtime_services=>attach_file_to_response(        EXPORTING   

  • Opening mail in safari

    Hi, I am new to the MAC, in Safari when you close or delete an e-mail the next e-mail open is there a way to stop this action. I do not like the mail to open automatically, specially if there is an attachment next. Thank you.