Error 6 occurred at Invoke Node in Dist Cmp Settings to Disk Hier.vi- Build Application.vi

My application runs fine under the LV 6.1 Professional Development System. When I attempt to add, in the application builder's source files tab, a dynamic vi that makes scope card and gpib calls, I get this error.
NI Scope and NI-488.2 ver 1.70 are installed.
Any suggestions?

I'm not sure if this will help, but you might take at look at these and give the ideas a try:
http://digital.ni.com/public.nsf/websearch/229402206118211186256752005C1E40?OpenDocument
http://digital.ni.com/public.nsf/websearch/862567530005F09C86256745006E4494?OpenDocument

Similar Messages

Error 7 occurred at Invoke Node in Dist read linkages.vi- Dist Cmp Settings to Disk Hier.vi- Build Application.vi

Error 7 occurred at Invoke Node in Dist read linkages.vi->Dist Cmp Settings to Disk Hier.vi->Build Application.vi????
Hi I do not understand how to resolve this nagging problem.
I run the program in the development time and it all goes smoothly.
However when i wanted to build the program. I often run into this problem.
How to resolve it?
Clement

Hey Clement,
Which version of LabVIEW are you using? There some knowledgebases out there that address the issue. Click here for the first KB or here for the second one. Hopefully these would help.
Regards,
Chetan K
Application Engineer
National Instruments

Error 6 at Invoke Node in Dist Send Result File to RT.vi-- Build Applicaiton.vi

I am using cFP 2000 RT in my application. When I build exe and download the application to the cFP 2000 RT, I get "Error 6 occured in Invoke Node in Dist Send Result File To RT.vi--> Build Application.vi"
The steps followed.
1. In the LabVIEW 7.0 Main Panel, Select the execution target as RT Target.
2. Tools --> Build Application or Shared Library. In the Target Tab the destination directory is selected as \\xxx.xxx.xxx.xxx\c\ni-rt\startup automatically.
3. In the SOurce file tab, select the Top level VI.
4. Press Build to make the executable of the application. The application is built and at the end the error message is poped up. (see the attached file)
Software Configuratio
n:
1. LabVIEW 7.0
2. Field Point 4.0
3. LabVIEW RT 7.0
Help me solve this problem. Thanks in advance.
Attachments:
Error_Message_and_RT_Info.bmp ‏313 KB

This is most likely coming from the specific file it mentions in the error, Dist Send Result File To RT.vi. The error 6 means the file can't be found. One thing to try first is to add this VI as a Dynamic VI in Application Builder. Another option is to change the path that this VI is invoked from, or is not called by an Invoke Node at all.
I hope this helps, feel free to contact support if the problem continues.
Regards,
Robert Jackson
Application Engineer

Error 6 occurred at invoke node in dist build app

Error 6 occurred at Invoke Node in Dist Build App from LLB.vi->Dist Build App Image.vi->Build Application.vi
Possible reasons:
LabView: Generic file I/O error
or
NI-488: I/O operation aborted
Version 6.0.2

I noticed that you updated your system to 6.0.2. A couple things to check on that may remedy the problem.
1)Did you install the application builder after upgrading your system to 6.0.2? You will want to install the application builder 6.0 first, and then add the 6.0.2 update to the whole system.
2)Have you mass compiled all of your VIs since the upgrade? You will want to make sure that all of your VIs are in 6.0.2 format before trying to build them into an executable.
Matt Kisler
Applications Engineer
National Instruments

Error 7 in Invoke Node in 'Dist Build App from LLB.vi'

I am encountering this error when trying to build an application. The error occurs while the builder is indicating that the application is actually being built (after files have been copied to the application). I am positive that all of my file paths are correct. I also have successfully mass compiled all of the VIs in the application. Is there something I'm overlooking?
The really funny thing is, using this same .bld script, I successfully built the application on another computer (running LV 7.0, just like this one).
My ideal approach to solving this problem would be to get into 'Dist Build App from LLB.vi' (or it's caller) and take a look at exactly which VI in my build is tripping up the build process.
Does anyone know the path for the LLB where I can find these VIs? And will I be able to access their block diagrams?
Thanks,
Nick
"You keep using that word. I do not think it means what you think it means." - Inigo Montoya

I just fixed the problem. When I said I was positive that all of the paths were correct, I was talking about paths to the LLBs in my build. However, somehow the LabVIEW system paths got changed. I don't recall ever doing anything to change LV's seach paths. I reset to the default values in Tools>>Options... and everything seems to work now. Sorry for the trouble, and thanks for the quick response, A.
-Nick
"You keep using that word. I do not think it means what you think it means." - Inigo Montoya

"Error 7 occurred at Invoke Node..." when attempting to open .vi for editing

I am attempting to open a vi for editing, and instead the vi is attempting to execute. I get the error:
"Error 7 occurred at Invoke Node in BuildTargetBuildSpecification.vi->BuildXFS.vi"
Possible reason(s): LabVIEW: File not found. The file might have been moved or deleted, or the file path might be incorrectly formatted for the operating system. For example, use \ as path separators on Windows, : on Mac OS, and / on Linux. Verify that the path is correct using the command prompt or file explorer.
Method Name: Project: Open
When I close the Error Message dialog, Labview terminates.

Hi R.Jay,
Error 7 generally occurs when trying to create an executable when there is an extra instance of a top-level vi. You may need to remove the file as a support file (but leave it as the top level vi).
Are you trying to run an executable that has already been created? Unless you have already built an executable, it should not automatically run when opened. Also, was it built in a previous version of LabVIEW? Sometimes this error can be seen when you upgrade to a newer version without compiling.
Regards,
Lauren
Applications Engineering
National Instruments

Build error after upgrading from 8.2.1 to 8.5 "Error 1055 occurred at Invoke Node..."

After upgrading to 8.5, I'm getting the following error when trying to build an EXE:
Visit the Request Support page at ni.com/ask to learn more about resolving this problem. Use the following information as a reference:
Error 1055 occurred at Invoke Node in AB_Source_Library.lvclass:Close_Reference.vi->AB_Build.lvclass:Copy_Files.vi->AB_Application.lvclass:Copy_Files.vi->AB_Build.lvclass:Build.vi->AB_EXE.lvclass:Build.vi->AB_Engine_Build.vi->AB_Build_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller
Possible reason(s):
LabVIEW: Object reference is invalid.
I have been building this application for both Windows and Mac OS, and I even get the same error when building the .app on an Intel Mac.
Things that I've already tried:
* Mass-compiling all my code
* Created the project from scratch
* Enabled each panel of the "diagram disable structure" one at a time and compiled again
Any ideas?

Hi Travis,
Ben’s advice if definitely the best place to start. Error 1055 is a very general LabVIEW error for “Object reference is invalid.” The cause is usually a bad install where important LabVIEW function aren’t placed in the right directory or aren’t installed at all.
Charlie M. CLD

Error 1003 occurred at Invoke Node

Good morning.
I work with LW8.5 and created with the following architecture:
There is main.vi on the links at the user's calls and runs the other VI.
That is, not directly, these are not included in the VI block diagram main.vi.
In the development of a happening in normal mode, all dynamically called VI,
But once I make EXE, when you try to call the dynamic VI error 1003.
Error 1003 occurred at Invoke Node in Main.vi
Possible reason (s):
LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the VI in LabVIEW using File>> Open and verify that it is runnable.
VI Path: C: \ Shaikov \ Labwiev \ builds \ NSIAES \ Initialsettings \ Initialsettings.vi
Show you how to act?
Thank you.

Hello margasan.
In my Projects I use to pass more dynamic and VI classes.
In the attached file - an example of my project:
In the main folder is a folder UpperClass, it is the parent class and child classes and HeirClass.lvclass Heir2Class.lvclass are organized into folders respectively Plugin1 and Plugin2, and these Classes inherit from the parent one and the same WI - UpperClassTest.vi. Plus, this Plugin1 has two, independent from the others, but related classes. A block diagram for an object placed Core.vi UpperClass.
So, here, if you take EXE, making llb files and run them from start VI for each of the Plugin, then everything works OK.
But as soon as I on the block diagram of a Plugin will put any object UpperClass, or one of its nasalednikov, there arises a familiar ERROR 1003. Prompt, plc, margasan I get rid of it in this case?
Attachments:
Example.zip ‏1481 KB

Error 8 occurred at Invoke Node in AB_EXE.lvclass:Build.vi- AB_Engine_Build.vi- AB_Build_Invoke.vi- AB_Build_Invoke.vi.ProxyCaller

Hi there,
Hope someone can help me. I recently upgraded to LV 8.5 and am having a problem building a .exe which has a subvi in it that opens in a new dialog window. When I try to build this I get the following error:
Error 8 occurred at Invoke Node in AB_EXE.lvclass:Build.vi->AB_Engine_Build.vi->AB_Build_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller
Possible reason(s):
LabVIEW: File permission error. You do not have the correct permissions for the file.
=========================
NI-488: DMA hardware error detected.
Method Name: Build:Application
I have built the .exe with the same subVi but without opening it in a dialog window and it works fine., so the problem seems to be linked to the inclusion of the dialog window.
Any advice greatly appreciated
Regards
Tadhg

UPDATe: I can get the .exe to build but now I get an error when I run teh .exe which is shown in the picture attached.
Attachments:
error screen1.JPG ‏122 KB

Error 8 occurred at Invoke Node in AB_EXE.lvclass:Build.vi- AB_Build.lvclass:Bui

During software build to make exe file, I got the following error message:
Error 8 occurred at Invoke Node in AB_EXE.lvclass:Build.vi->AB_Build.lvclass:Build_from_Wizard.vi->AB_UI_FRAMEWORK.vi->AB_Item_OnDoProperties.vi->AB_Item_OnDoProperties.vi.ProxyCaller
Possible reason(s):
LabVIEW: File permission error. You do not have the correct permissions for the file.
=========================
NI-488: DMA hardware error detected.
Method Name: Build:Application
The vi was working fine before the build. It just access some text files and creates some excel files. No hardware is involved. See if anybody know how to solve this problem. Thanks.

I am using LabVIEW 2014 and have been getting this error randomly, but fairly consistently on a recent build. I searched all over and could not find a solution that worked. However, just through trial and error I discovered that the problem is related to SSE2 Optimization in the Advanced properties window. I can consistently cause this error by enabling this feature and consistently compile successfully when it is disabled. Try turning this feature off and see if it solves the problem.
...UPDATE: After closing and re-opening LabVIEW this error came back, and did not seem to be affected by the SSE2 option. Not that it isn't related, but perhaps not the silver bullet I thought it was.
I also got the error to go away sometimes when I compiled the EXE while the main program VI was open, whereas it gave the error most of the time when no VIs were open...again, nothing seems to consistently solve the problem...there is definitely some kind of bug in the appllication builder, and it seems like there are a lot of people that have been struggling with this for a long time (as far back as LV 8)...hopefully NI eventually finds this bug and squashes it!..although, I doubt that anybody at NI is even looking for it...

Error 7 occurred at Invoke Node in AB_EXE.lvclass

I get the "Error 7 occurred at Invoke Node in AB_EXE.lvclass" error when trying to build an executable in Labview 8.5.1. I can run the application without any errors but when I try to build the executable, I get the error. I have tried a mass compile of the project, tried ctrl + shift + run on the top level vi, and tried to mass compile the folder where the project is located and nothing seems to help. I have also looked at the project dependencies for conflicts and found none. I have made a new project and tried to build an executable from this same code without any luck. How can I get this to build an executable?
The exact error is:
Error 7 occurred at Invoke Node in AB_EXE.lvclass:Build.vi->AB_Engine_Build.vi->AB_Build_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller
Possible reason(s):
LabVIEW: File not found. The file might have been moved or deleted, or the file path might be incorrectly formatted for the operating system. For example, use \ as path separators on Windows, : on Mac OS, and / on Linux. Verify that the path is correct using the command prompt or file explorer.
=========================
NI-488: Nonexistent GPIB interface.
Method Name: Build:Application

Are you using the Report Generation Toolkit? A lot of error 7's during builds seem to be related to this toolkit. Any dynamically called VI's?
Take a look here and here.
Also search the forums for "error 7" and you'll find some other threads related to error 7 and the application builder.

Error 1172 occured at invoke node

Hello
I am new to Labview and object oriented programming. I have an already written c# code which communicates with a digital I/O card attached to a test system. I want to run those c# functions in labview. I am using .NET constructor pallett and then invoke node but I am receiving following Error:
Error 1172 occurred at Invoke Node Error calling method DmmCSharp.Handler.Reset, (System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation.
Inner Exception: System.Runtime.InteropServices.COMException: KtMDsr: A connection to the instrument has not been established.)
Image file of error and vi file is attached below.
Attachments:
vi file.png ‏5 KB
error.png ‏45 KB

The clue is in the 'A connection to the device has not been established'. You are trying to reset the device - presumably without having first configured the appropriate parameters or opened connection to it so the library is probably throwing that error.
Certified LabVIEW Architect, Certified TestStand Developer
NI Days (and A&DF): 2010, 2011, 2013, 2014
NI Week: 2012, 2014
Knowledgeable in all things Giant Tetris and WebSockets

Error 1 occurred at Invoke Node in openvi.vi

Hello, in openvi.vi, I use Invoke Node to run showchannel2.vi, I met problem about error 1. please see attachment file.
This problem have been described below absolutely.
Error 1 occurred at Invoke Node in openvi.vi
Possible reason(s):
LabVIEW: An input parameter is invalid.
NI-488: Command requires GPIB Controller to be Controller in Charge.
I don't know why? How can I overcome this question?
Thank you very much
Solved!
Go to Solution.
Attachments:
openvi.vi ‏38 KB
ShowChannel2.vi ‏79 KB

The datatypes of your controls don't match. In the subVI you have a U8. In the parent VI the slider is a DBL. Change the slider's datatype to a U8. You should also make sure you have a valid range on your slider. In the subVI you're subtracting 8 from the input value, so it seems you're wanting a control with a minimum value of 8.

Error occured in invoking event "contextInitialized()" on listener class co

Hi All,
I am working on JSF 1.2 on SAP NetWeaver CE. I am able to execute sample JSF application successfully when NO java program is written in the application. When I write a java program inside the JSF application...I am getting following error. Please let me know how to proceed on this:
"Application error occurred during the request procession."
Error occured in invoking event "contextInitialized()" on listener class com.sun.faces.config.ConfigureListener.
Details:
java.lang.UnsupportedClassVersionError: Bad version number in .class file
at java.lang.ClassLoader.defineClass1(Native Method)
at java.lang.ClassLoader.defineClass(ClassLoader.java:654)
at com.sap.engine.boot.loader.ResourceMultiParentClassLoader.loadClassLocal(ResourceMultiParentClassLoader.java:198)
at com.sap.engine.boot.loader.MultiParentClassLoader.findClassInLoaderGraph(MultiParentClassLoader.java:302)
at com.sap.engine.boot.loader.MultiParentClassLoader.loadClass(MultiParentClassLoader.java:256)
at com.sap.engine.boot.loader.MultiParentClassLoader.loadClass(MultiParentClassLoader.java:228)
at com.sun.faces.config.ManagedBeanFactoryImpl.getManagedBeanClass(ManagedBeanFactoryImpl.java:227)
at com.sun.faces.config.ManagedBeanFactoryImpl.scanForAnnotations(ManagedBeanFactoryImpl.java:1130)
at com.sun.faces.config.ManagedBeanFactoryImpl.<init>(ManagedBeanFactoryImpl.java:156)
at com.sun.faces.config.ConfigureListener.configure(ConfigureListener.java:926)
at com.sun.faces.config.ConfigureListener.configure(ConfigureListener.java:507)
at com.sun.faces.config.ConfigureListener.contextInitialized(ConfigureListener.java:402)
at com.sap.engine.services.servlets_jsp.server.application.WebEvents.contextInitialized(WebEvents.java:74)
at com.sap.engine.services.servlets_jsp.server.deploy.ApplicationThreadInitializer.run(ApplicationThreadInitializer.java:198)
at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
at java.security.AccessController.doPrivileged(Native Method)
at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:152)
at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:247)
Rgds,
Pathan

Pathan wrote:
java.lang.UnsupportedClassVersionError: Bad version number in .class fileThe Java version of the Java compiler used is newer than the Java version of the Java runtime used.
E.g. compiling with JDK 1.6 and running with JRE 1.5 would cause this error.

An error occurred when invoking the authorization extension. (rsAuthorizationExtensionError)

Hello,
I'm not sure when (I suspect SQL 2012 SP1 CU3 and Windows Updates) reporting stopped working.
In Internet Explorer I have error:
An error occurred when invoking the authorization extension. (rsAuthorizationExtensionError)
Get
Online Help
For more information about this error navigate to the report server on the local server machine, or enable remote errors
In MSSRS logs lot of:
library!ReportServer_0-1!15f4!03/31/2015-00:00:42:: i INFO: Call to ListChildrenAction(/, False).
library!ReportServer_0-1!15f4!03/31/2015-00:00:42:: e ERROR: Throwing Microsoft.ReportingServices.Diagnostics.Utilities.AuthorizationExtensionException: , Microsoft.ReportingServices.Diagnostics.Utilities.AuthorizationExtensionException: An error occurred
when invoking the authorization extension. ---> System.ServiceModel.FaultException`1[System.ServiceModel.ExceptionDetail]: The type initializer for 'Microsoft.EnterpriseManagement.Mom.ServiceDataLayer.SdkDataAccess' threw an exception. (Fault Detail is
equal to An ExceptionDetail, likely created by IncludeExceptionDetailInFaults=true, whose value is:
System.TypeInitializationException: The type initializer for 'Microsoft.EnterpriseManagement.Mom.ServiceDataLayer.SdkDataAccess' threw an exception. ----> System.Exception: Exception decrypting. The specified file could not be decrypted
at Microsoft.EnterpriseManagement.Security.DPAPIWrapper.Decrypt(Byte[] cipherText)
at Microsoft.EnterpriseManagement.Security.AsymmetricKeyManager.Initialize(Byte[] publicKey)
at Microsoft.EnterpriseManagement.Security.SecureStorageManager.Initialize()
at Microsoft.EnterpriseManagement.Mom.ServiceDataLayer.SdkDataAccess.get_secureStorageDatabaseManager()
at Microsoft.EnterpriseManagement.Mom.ServiceDataLayer.SdkDataAccess..cctor()
--- End of inner ExceptionDetail stack trace ---
at Microsoft.EnterpriseManagement.Mom.ServiceDataLayer.SdkDataAccess..ctor()
at CreateMicrosoft.EnterpriseManagement.Mom.ServiceDataLayer.SdkDataAccessBackCompatProxy()
at Syst...).
--- End of inner exception stack trace ---;
MSSRS version is
Microsoft SQL Server Reporting Services Version 2011.0110.5058.00.
I tried to delete all encrypted content, restart SQL and Reporting few times, install last Windows Update updates and don't have idea what to do more.
SQL and MSSRS services are working on domain accounts, nothing changes.

Hi LukaszH,
Thank you for your question.
I am trying to involve someone more familiar with this topic for a further look at this issue. Sometime delay might be expected from the job transferring. Your patience is greatly appreciated.
Thank you for your understanding and support.
Best regards,
Qiuyun Yu
Qiuyun Yu
TechNet Community Support

Error 6 occurred at Invoke Node in Dist Cmp Settings to Disk Hier.vi- Build Application.vi

Similar Messages

Maybe you are looking for