Error after setting up direct LDAP

Running iMS 5.2 and LDAP 4.1.6
after making the changes to set up direct LDAP lookup I started getting the following error:
4.0.0 temporary error returned by alias expansion
While making the changes to set the server back to dirsync mode I noticed that the databases:
aliasesdb.db and reversedb.db had been recreated but were significanly smaller than the originals.
After changing the imta.cnf, option.dat,job_controller.cnf and mappings files back and replacing my db files I ran a imsimta cnbuild and a full dirsync and everything functioned normal again.
Any ideas?
Don

Hi Roger and Jay,
I followed the instructions exactly. I have restored my backups of the config files a couple times and started over again. I did catch the error that Roger pointed out and my line read exactly like his example (with my domain of course)
This is my old mailserver. I have a new one working right now. I am trying to get the updates all working on this one before I mess up the production machine so there is no problem with it being down while I work the bugs out.
Here is a clip from the ldap access log
the last line shows an error 11 that I assume is the problem.
[14/Dec/2004:15:44:29 -0700] conn=46 op=1 SRCH base="dc=sturgeon,dc=ab,dc=ca,o=Internet" scope=0 filter="(|(objectclass=inetDomain)(objectclass=inetdomainalias))"
[14/Dec/2004:15:44:29 -0700] conn=46 op=1 RESULT err=0 tag=101 nentries=1 etime=0
[14/Dec/2004:15:44:29 -0700] conn=46 op=2 SRCH base="o=sturgeon.ab.ca,o=ab.ca" scope=2 filter="(&(objectclass=groupOfUniqueNames)(objectclass=inetMailAdministrator))"
[14/Dec/2004:15:44:29 -0700] conn=46 op=2 RESULT err=0 tag=101 nentries=1 etime=0
[14/Dec/2004:15:44:29 -0700] conn=46 op=3 SRCH base="cn=Domain Administrators,ou=Groups,o=sturgeon.ab.ca,o=ab.ca" scope=0 filter="(objectclass=*)"
[14/Dec/2004:15:44:29 -0700] conn=46 op=3 RESULT err=0 tag=101 nentries=1 etime=0
[14/Dec/2004:15:44:29 -0700] conn=46 op=4 SRCH base="o=sturgeon.ab.ca,o=ab.ca" scope=2 filter="(uid=carlgren)"
[14/Dec/2004:15:44:29 -0700] conn=46 op=4 RESULT err=0 tag=101 nentries=1 etime=0
[14/Dec/2004:15:44:29 -0700] conn=47 fd=54 slot=54 connection from 192.168.0.12 to 192.168.0.12
[14/Dec/2004:15:44:29 -0700] conn=47 op=0 BIND dn="uid=carlgren,ou=people,o=sturgeon.ab.ca,o=ab.ca" method=128 version=3
[14/Dec/2004:15:44:29 -0700] conn=47 op=0 RESULT err=0 tag=97 nentries=0 etime=0
[14/Dec/2004:15:44:29 -0700] conn=46 op=5 SRCH base="cn=Service Administrators,ou=Groups,o=ab.ca" scope=0 filter="(objectclass=groupOfUniqueNames)"
[14/Dec/2004:15:44:30 -0700] conn=46 op=5 RESULT err=0 tag=101 nentries=1 etime=1
[14/Dec/2004:15:44:30 -0700] conn=46 op=6 SRCH base="uid=carlgren,ou=people,o=sturgeon.ab.ca,o=ab.ca" scope=0 filter="(objectclass=*)"
[14/Dec/2004:15:44:30 -0700] conn=46 op=6 RESULT err=0 tag=101 nentries=1 etime=0
[14/Dec/2004:15:44:31 -0700] conn=48 fd=55 slot=55 connection from 192.168.0.12 to 192.168.0.12
[14/Dec/2004:15:44:31 -0700] conn=48 op=0 BIND dn="uid=msg-admin-1,ou=People,o=sturgeon.ab.ca,o=ab.ca" method=128 version=3
[14/Dec/2004:15:44:31 -0700] conn=48 op=0 RESULT err=0 tag=97 nentries=0 etime=0
[14/Dec/2004:15:44:31 -0700] conn=48 op=1 SRCH base="ou=carlgren,ou=people,o=sturgeon.ab.ca,o=ab.ca,o=pab" scope=2 filter="(|(cn=*)(ou=*))"
[14/Dec/2004:15:44:31 -0700] conn=48 op=1 RESULT err=0 tag=101 nentries=40 etime=0
[14/Dec/2004:15:44:31 -0700] conn=48 op=2 SRCH base="ou=carlgren,ou=people,o=sturgeon.ab.ca,o=ab.ca,o=pab" scope=2 filter="(|(objectclass=pab)(objectclass=pabgroup))"
[14/Dec/2004:15:44:31 -0700] conn=48 op=2 RESULT err=0 tag=101 nentries=2 etime=0
[14/Dec/2004:15:44:31 -0700] conn=48 op=3 SRCH base="ou=carlgren,ou=people,o=sturgeon.ab.ca,o=ab.ca,o=pab" scope=2 filter="(memberofpab=AddressBook271b6af)"
[14/Dec/2004:15:44:31 -0700] conn=48 op=3 RESULT err=0 tag=101 nentries=37 etime=0
[14/Dec/2004:15:44:42 -0700] conn=38 op=3 SRCH base="o=sturgeon.ab.ca,o=ab.ca" scope=2 filter="(|([email protected])([email protected])([email protected]))"
[14/Dec/2004:15:44:49 -0700] conn=38 op=3 RESULT err=11 tag=101 nentries=1 etime=7 notes=U
If I put the machine back into dirsync mode then everything works fine. I must be missing something.
In the morning I'll try again.
Thanks for the help,
Don

Similar Messages

Error after setting the iTunes prefereces.

Hi, I have istalled the latest version of iTunes6.0.4.2.
Now after setting the iTunes preferences i clicked OK, Then i got an error message saying ....
"An error occured while updating the default platyer for audio file types. You do not have enough access privileges for this operation"
Can somebody please help me, how can i get rid of this error message.

Rachyl, Could you please let me know an alternative/solution for this.
Actually we will distribute this to around 500 employees in our company. If this message pops-up while they using iTunes it won't be nice, all of them will defenitely complaits about this problem.
That is why i am trying to find out a solution for this before giving iTuens to our users.
Thanks much,
Chetan.

Error after Setting up DBI

Hi all,
After setting up Daily business intelligence for Projects. The error occurs as shown below
"A system error has occurred. Unable to locate: CURRENT PERIOD. Please contact your support representative."
Pls help me to resolve this
Thanks
Dinesh

I believe you need to open a service request with Oracle support for help on this. Someone needs to see your installation setup and configuration to start to figure out what is going wrong, and we on this forum are not able to do that, while Oracle support can do so.
John Dickey

Some things no longer work after switch to direct LDAP mode

Hi,
today i have tried switching to direct ldap mode following the documentation
now i can no longer send mail directed to hosts as
[email protected]
i always get a 5.1.1 unknown or illegal alias:
whereas email@{subdomain}.domain.com is ok, as long as the subdomain is known to the MTA, ie it is an alias object in the DC tree
also, some aliases defined in the file "aliases" are no longer recognized,
for convenience, i had some default forward lines likes
*@domain.com: @otherrelay:*@domain.com
which effectively acted like a smarthost, ie mail to addresses not known in domain.com were forwarded to "otherrelay"
now, probably i could solve the second problem either using a smarthost in the DC tree 's domain config
the first problem, however, puzzles me...it look like if it doesn't find a matching address, and the host is not known as a domain, then further rewrite rules are not applied ?

i found the problem,
in option.dat, DOMAIN_UPLEVEL must be set to 0, in order to have the old behaviour (wildcards in aliasfile, and possibility to send mails directly to specified hosts)
i had set it to 1, in the hope the MTA would be more tolerant to find users (if [email protected] is not found, then maybe it exists at [email protected], so use this instead) as some of our users have quite problems addressing other users in the correct subdomain.

Error after setting up new Taskflow

I have copied the existing taskflow in HRMS application "US HRMS PERSON TASKFLOW" and created a new one. Every node in the new taskflow is the same as the old one, only I have added one node in this new taskflow.
However, after assigning this taskflow to a function when I click on that button which points to the new node, I get the below error:
Function not available to this responsibility. Change responsibilities or contact your System Administrator.
Does anyone know the solution for this.

Seeing as your question is a Oracle Enterprise Business Suite (EBS) question, please post it in the [EBS General Discussion|http://forums.oracle.com/forums/forum.jspa?forumID=475] forum where you will have greater success in getting your question answered.
Craig...

The account password was not specified. Error after setting up a second Crawl Database and Crawler on different server.

We have a three server farm. (SPWebTest, SPAppTest, SPDBTest)
We have added an additional database server (SPDBRMTest) and an additional application server (SPAPPRMTest).
Today I created a new Crawl Database on SPDBRMTest and a new Crawler on SPAPPRMTest.
I create a distribution rule to all crawling activity for 1 web application to the new crawl database on SPDBRMTest.
This web application was part of the original crawl and had no errors or issues. We are trying to scale our Search to improve performance but when a full crawl is executed against this content source I get the following crawl error:
"The account password was not specified. Specify the password."
I have tried re-entering the "Default Content Access Account" but the issue continues.

Hi Brian,
when you add the crawl rules, do the account that is provided have the permission to read the content at the web application?
http://technet.microsoft.com/en-us/library/jj219686(v=office.15).aspx
please disable the loopback check, perhaps it may help:
http://support.microsoft.com/kb/896861
Regards,
Aries
Microsoft Online Community Support
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Problem with Direct LDAP

Hi Jay,
I am having a problem with the switch to Direct LDAP. I am finally doing it on my production server. Using ldap 4.16 currently. Once I get this working I am upgrading to 5.2
We have a server that holds messages until a user releases them. This server is called ewall.mydomain.com.
They get a message in their inbox that allows them to click on a link to send the ewall server a message to release the held mail.
the link would look like this:
[email protected]
(all on one line)
This worked just fine in dirsync mode but after switching to Direct Ldap I get an 5.1.1 unknown or illegal alias when the user tries to send the message. If I switch back to dirsync mode it works fine again. Everything else is working fine.
Any ideas?
Thanks
Don

Well, it means that for some reason, your [email protected]
user isn't being picked up in the direct ldap.
It could be that your domain is "mydomain.com", and the user is in "ewall.mydomain.com". dirsync assumes that subdomains are part of an overall domain
direct ldap doesn't, unless you set
domain_uplevel=3 in your option.dat, and recompile

Direct Ldap Issue

Hi
I am using messaging server 5.2. Previously we are using Dirsync in our messaging server , after migrating to direct Ldap we are receiving the the following error
for some domain
"5.1.1 unknown or illegal alias: [email protected]"
i am attaching the output of /imsimta test -rewrite [email protected] for your reference
forward channel = l
channel description =
channel user filter =
dest channel filter =
source channel filter =
channel flags #0 = BIDIRECTIONAL MULTIPLE IMMNONURGENT NOSERVICEALL
channel flags #1 = NOSMTP DEFAULT
channel flags #2 = NOSENDPOST NOWARNPOST POSTHEADONLY HEADERINC NOEXPROUTE
channel flags #3 = LOGGING NOGREY NORESTRICTED RETAINSECURITMULTIPARTS
channel flags #4 = EIGHTBIT NOHEADERTRIM NOHEADERREAD RULES
channel flags #5 =
channel flags #6 = LOCALUSER REPORTHEADER
channel flags #7 = NOSWITCHCHANNEL NOREMOTEHOST DATEFOUR DAYOFWEEK
channel flags #8 = NODEFRAGMENT EXQUOTA REVERSE NOCONVERT_OCTET_STREAM
channel flags #9 = NOTHURMAN INTERPRETENCODING USEINTERMEDIATE RECEIVEDFROM VALIDATELOCALSYSTEM NOTURN
defaulthost = hathway.com hathway.com
linelength = 1023
channel env addr type = SOURCEROUTE
channel hdr addr type = SOURCEROUTE
channel official host = mhr.hathway.com
channel queue 0 name = LOCAL_POOL
channel queue 1 name = LOCAL_POOL
channel queue 2 name = LOCAL_POOL
channel queue 3 name = LOCAL_POOL
channel after params =
channel user name =
urgentnotices = 1 2 4 7
normalnotices = 1 2 4 7
nonurgentnotices = 1 2 4 7
channel rightslist ids =
local behavior flags = %x7
backward channel = l
header To: address = [email protected]
header From: address = [email protected]
envelope To: address = [email protected] (route (mhr.hathway.com,mhr.hathway.com)) (host ol24.net)
envelope From: address = [email protected]
name =
mbox = test
Extracted address action list:
[email protected]
Extracted 733 address action list:
[email protected]
Address list expansion:
0 expansion total.
Expanded address:
[email protected]
Submitted address list:
Address list error -- 5.1.1 unknown or illegal alias: [email protected]
Submitted notifications list:
Regards
Prashant

Prashant_wagh wrote:
I am using messaging server 5.2. Previously we are using Dirsync in our messaging server , after migrating to direct Ldap we are receiving the the following error for some domain Please always provide the full version of Messaging Server (./imsimta version).
"5.1.1 unknown or illegal alias: [email protected]"
Was this address "working" prior to implementing direct-ldap?
This issue usually occurs for two reasons:
1) You have no user/group LDAP entry which has a mail:/mailalternateaddress:/mailequivalentaddress: of [email protected]
2) You have more then one entry with a mail:/mailalternateaddress:/mailequivalentaddress: of [email protected]
The old (and broken) dirsync mechanism would "handle" the second scenario. You can check to see whether you have (1) or (2) occurring by performing an ldap search e.g.
ldapsearch -h <directory server> -b <user/group base> -D "cn=directory manager" -w <directory manager password> \
"(|(mail=[email protected])(mailalternateaddress=[email protected])(mailequivalentaddress=[email protected]))" dn
e.g.
ldapsearch -h myserver.com -b o=isp -D "cn=directory manager" -w secretpass \
"(|(mail=[email protected])(mailalternateaddress=[email protected])(mailequivalentaddress=[email protected]))" dnRegards,
Shane.

Even after adding the country code i can't seem to make any international calls.im not sure if this is relevant but apparently, the option dial assist is not to be found on my setting.pls direct me...thank you.and my phone moddle is 5s(A1457)gold

even after adding the country code i can't seem to make any international calls.im not sure if this is relevant but apparently, the option dial assist is not to be found on my setting.pls direct me...thank you.and my phone moddle is 5s(A1457)gold eddition.

Hi, Thilina66. You say you have entered the country code but still cannot make international calls. I suppose you are adding the international access code before the country code. This internaltional access code (011 in the US, 00 in Europe, etc.) can be substituted by adding a + sign before the country code.
For example, to call a number in the UK from the US you have to dial:
011 44 7540 267898
or
+44 7540 267898
To call a number in the US from the UK you have to dial:
00 1 212 456 1470
or
+1 212 456 1470
Please check that the contact number in your address book is correctly written if you are dialing directly from the address book or that you enter the correct numbers in the keyboard if you are dialing from the keyboard.

"No bootable device --- insert boot disk and press any key" after setting up Bootcamp

Hi guys,
I am trying to install Windows 7 via Bootcamp but after setting up Bootcamp and restarting the computer I get the error message "No bootable device --- insert boot disk and press any key".
I use an iMac with a DIY Fusion Drive consisting of a 120 GB SSD and a 1 TB HDD.
Since Bootcamp can only be installed on the HDD I believe disk1 is the interesting one. Here is the output of sudo gpt -r -vv show disk1:
gpt show: disk1: mediasize=1000204886016; sectorsize=512; blocks=1953525168
gpt show: disk1: Suspicious MBR at sector 0
gpt show: disk1: Pri GPT at sector 1
gpt show: disk1: Sec GPT at sector 1953525167
       start        size index contents
           0           1         MBR
           1           1         Pri GPT header
           2          32         Pri GPT table
          34           6
          40      409600      1 GPT part - C12A7328-F81F-11D2-BA4B-00A0C93EC93B
      409640 1709658208      2 GPT part - 53746F72-6167-11AA-AA11-00306543ECAC
1710067848     1269536      3 GPT part - 426F6F74-0000-11AA-AA11-00306543ECAC
1711337384          88
1711337472   242186240      4 GPT part - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
1953523712        1423
1953525135          32         Sec GPT table
1953525167           1         Sec GPT header
And the output of sudo fdisk /dev/disk1:
Disk: /dev/disk1
geometry: 121601/255/63 [1953525168 sectors]
Signature: 0xAA55
         Starting       Ending
#: id cyl hd sec - cyl hd sec [     start -       size]
1: EE    0   0   2 -   25 127 14 [         1 -     409639] <Unknown ID>
2: AF   25 127 15 - 1023 254 63 [    409640 - 1709658208] HFS+
*3: 07 1023 254 63 - 1023 254 63 [1711337472 - 242186240] HPFS/QNX/AUX
4: 00    0   0   0 -    0   0   0 [         0 -          0] unused
Here is also the list of my disks:
/dev/disk0
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *120.0 GB   disk0
   1:                        EFI EFI                     209.7 MB   disk0s1
   2:          Apple_CoreStorage                         119.7 GB   disk0s2
   3:                 Apple_Boot Boot OS X               134.2 MB   disk0s3
/dev/disk1
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *1.0 TB     disk1
   1:                        EFI EFI                     209.7 MB   disk1s1
   2:          Apple_CoreStorage                         875.3 GB   disk1s2
   3:                 Apple_Boot Recovery HD             650.0 MB   disk1s3
   4:       Microsoft Basic Data BOOTCAMP                124.0 GB   disk1s4
/dev/disk2
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:                  Apple_HFS FusionDrive            *975.5 GB   disk2
                                 Logical Volume on disk0s2, disk1s2
                                 FFA13FBC-2001-40B7-8BBB-BE6EECF8AC11
                                 Unencrypted Fusion Drive
/dev/disk3
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:                            GRMCPRXFRER_DE_DVD     *3.2 GB     disk3
I have gdisk installed and am ready to mess around. Any help would be greatly appreciated!

So, when I started my iMac yesterday morning it couldn't boot into OS X anymore either. Several hours of restoring later I am back to square one. I tried installing Windows 7 via Bootcamp again but got the same error message. This time I noticed though that Bootcamp asked me to remove the bootable option from the USB drive with the support drivers in order to install from DVD. Does that ring any bells? I am building another USB drive right now, hoping it would ask me again but this I will decline and try to boot from it.
When you restored, was a Time Machine restore used? TM does not backup Bootcamp and does an erase of the partition. It may also erase the entire disk (including the Fusion drive) if the specific backup of the volume layout of the disks indicates a pre-Bootcamp layout.
My MacBook Pro is a 2009 model and also once had a built-in optical drive. I have no idea why it would work on there but not on the iMac.
You also wrote
When I plug the external DVD drive in, the boot manager recognizes a "Windows" disc and an "EFI Boot" disc. If I select the "Windows" disc I get a black screen with a blinking dash.
The blinking dash indicates that it is working, but does not have the requisite drivers to enable the GPU/Mouse/Keyboard on the media being used.
In the MBP case, did you have two drives installed in the MBP, a Fusion configuration, and then were able to successfully install Bootcamp?
For example on a Mac mini I have a DIY Fusion drive, but the sequence was done differently. Bootcamp was installed using a USB stick+Windows 7 ISO.
1. The two disks are not in a CoreStorage set up initially.
2. The second disk is partitioned (64Gb) and a Bootcamp W7 install completed via USB (this is different HW as compared to IMac, because it has no Optical drive).
3. After the HDD is partitioned, the first partition and the SSD are then used to create a CoreStorage volume.
4. Here is the working version and disk layout. (I plan to erase both disks, put W7 on a partition on the SSD, and make the non-Bootcamp+entire HDD in a CoreStorage volume).
diskutil cs list
CoreStorage logical volume groups (1 found)
|
+-- Logical Volume Group A8C00490-0E14-401F-AB69-59F37724E8C4
    =========================================================
    Name:         Fusion
    Status:       Online
    Size:         1190201270272 B (1.2 TB)
    Free Space:   0 B (0 B)
    |
    +-< Physical Volume 4772013B-5520-4801-9BE5-BCAEF4AEDAB3
    |   ----------------------------------------------------
    |   Index:    0
    |   Disk:     disk0s2
    |   Status:   Online
    |   Size:     255716540416 B (255.7 GB)
    |
    +-< Physical Volume A679A101-3C78-4A59-B5EE-A4339210CFAD
    |   ----------------------------------------------------
    |   Index:    1
    |   Disk:     disk1s2
    |   Status:   Online
    |   Size:     934484729856 B (934.5 GB)
    |
    +-> Logical Volume Family 5EF5C7CA-0B9C-4169-82A1-41C84F206672
        Encryption Status:       Unlocked
        Encryption Type:         None
        Conversion Status:       NoConversion
        Conversion Direction:    -none-
        Has Encrypted Extents:   No
        Fully Secure:            No
        Passphrase Required:     No
        |
        +-> Logical Volume 1512657C-ED13-4B31-82C6-7AECBBCA7F98
            Disk:                  disk2
            Status:                Online
            Size (Total):          1185508581376 B (1.2 TB)
            Conversion Progress:   -none-
            Revertible:            No
            LV Name:               Fusion HD
            Volume Name:           Fusion HD
            Content Hint:          Apple_HFS
diskutil list
/dev/disk0
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *256.1 GB   disk0
   1:                        EFI EFI                     209.7 MB   disk0s1
   2:          Apple_CoreStorage                         255.7 GB   disk0s2
   3:                 Apple_Boot Boot OS X               134.2 MB   disk0s3
/dev/disk1
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *1.0 TB     disk1
   1:                        EFI EFI                     209.7 MB   disk1s1
   2:          Apple_CoreStorage                         934.5 GB   disk1s2
   3:                 Apple_Boot Boot OS X               650.0 MB   disk1s3
   4:       Microsoft Basic Data BOOTCAMP                64.9 GB    disk1s4
/dev/disk2
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:                  Apple_HFS Fusion HD              *1.2 TB     disk2

Laptop only coming up with a blank screen after set-up?

Ok, so. My parents bought me a brand new hp laptop for christmas. On christmas day i went through the whole set-up process and did all the steps it told me to do. When i'd been through all the steps, i got a loading symbol and ever since, all it comes up with is a blank, black screen and a mouse icon that i can move. I'm not 100% sure of the model though (appologies). What do i need to do??
Cheers

Hello @15_,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your notebook is coming up with a blank screen after setting it up. Is the power on the computer on? Is there an error message on the screen? I would be happy to help you, but first I would encourage you to post your product number for your computer. Below is a is an HP Support document that will demonstrate how to find your computer's product number. In addition, it will also help if you indicate which operating system you are using; and whether your operating system is 32 or 64 bit. The more information you can provide, the better!
How Do I Find My Model Number or Product Number?
Which Windows operating system am I running?
Is the Windows Version on My Computer 32-bit or 64-bit?
Please re-post with the necessary information, this way I will be able to research this further for you. I look forward to your reply!
Cheers!
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

"Page not found" error after 5 minutes of see "processing" on the screen

We are using WebLogic 8.1 server and also the WebLogic proxy as our front end. When a user runs a process that takes over 5 minutes using the Proxy URL they receive an IE "Page not found" error after 5 minutes of seeing "processing" on the screen. If they run it on none Proxy URL (directly on WebLogic server) it works fine.
We have looked into the WLIOTimeoutSecs parameter and set in the web.xml for both the HttpClusterServlet and HttpProxyServlet, but this had no affect.
Is there another timeout that controls this 5 minute timeout? It seems if one uses Apache and sets the WLIOTimeoutSecs parameter to a higher number than 300 seconds there is not an issue.
Did this parameter get omitted for the WebLogic Proxy and if so, what does one use?
Thanks,
Jim

Hello George,
Thank you for the quick reply. I will surely try the option suggested by you.
But what i was thinking is that as this is not a Connection Time Out (500) error, instead its a Page Not Found error, it would be Session-Timeout and not Connection Time-Out.
Maybe I should be looking at:
SESSION-TIMEOUT due to kernel:
Kernel parameter: rdisp/gui_auto_logout
Kernel parameter: rdisp/plugin_auto_logout
as per the SAP OSS Note: 705013
But again, I think this Note is pointing to the SICF service and IAC type of iView and not SAP Transaction type iView. Please advice.
Thanks,
Gaurav
Edited by: Gaurav Shah on Dec 4, 2008 9:37 PM
Edited by: Gaurav Shah on Dec 4, 2008 9:42 PM

Error after updating version 6.0.2.5 to 6.0.2.10

Hello,
I wonder if anyone could help with an error I'm seeing after installing SP10. I was able to install
successfully to the repository and application server, then all process servers. All but one process server
is able to startup local -- for ease of reading we'll call this one 'Server A'.
Server A (HP-US IA64) has one PS configured for production and one for qa. The configuration is handled as such:
/etc/inetd.conf
rwnp stream tcp nowait cronacle /-----/------/-----/----/rwnp rwnp
rwnq stream tcp nowait cronacle /-----/------/-----/----/rwnq rwnq
/etc/services
rwnp -----/tcp # Redwood Cronacle u2013 Production
rwnq -----/tcp # Redwood Cronacle u2013 QA
$JCS_HOME/admin/rwtab.jcs
servera_dbq:/---/redwood/server/602:::CRNQ:Y
servera_dbp:/---/redwood/server/602:::CRNP:Y
$JCS_HOME/admin/initservera_dbp.jcs
$JCS_HOME/admin/initservera_dbq.jcs
$JCS_HOME/bin/rwnq
$JCS_HOME/bin/rwnp
Initially Server A and Server B weren't resolving the 'found' name correctly. In order to get Server B to
startup, I had to force the license server to change the hostname to a different alias.
RS> set license host ********
After setting the license host, I ran the setup license command for Server A. Now B will startup but A,
rather than being unable to resolve, now shows the license as tampered with. Installation of SP10 also
fails with the same error on Server A.
cd $JCS_HOME/install
sh ./setup license
        --answer questions--
- Obtaining license phase FAILED!
Connected.
JCS-00348: invalid security key
Current license information:
Company name    : Bechtel Corporation
Contract no     : -----------------
Registration key: ----.----.----.----.----.----
License host    : --------
        This license was tampered with.
* Abort the install?
        Answer: [YN](Y)
! ABORT: User aborted installation
When I attempt to startup the scheduler for Server A there is the following error:
RS> startup SERVERA_DBQ local
JCS-00348: invalid security key
JCS-00328: your license is not valid. Type SHOW LICENSE to examine license
When I type 'show license' at the RS prompt I receive another error:
RS> show license
JCS-00348: invalid security key
Current license information:
Company name    : Bechtel Corporation
Contract no     : -----------------
Registration key: ----.----.----.----.----.----
License host    : --------
        This license was tampered with.
Does anyone have any idea of what to look for in this configuration, or at least poitn me in the right
direction?
Thank you for any help you can provide,
Renee

Hi Renee,
Looks like you solved the problem, you've flagged your question as answered already :-).
A possible cause for the issue you experienced is version differences in the executables, maybe the update of one process server installation failed (f.i. binaries in use) or was missed (f.i. the secondary node of a cluster installation).
I hope everything is resolved for you now, let me know if you need any additional information.
Kind regards,
Anton Goselink.

Direct Ldap configuration mismatch....

I am running directory server 5.1 and messaging server 5.2.
I have one message store (msA.example.com) for users to retriew mail and it queries directory master server (dsA.exaple.com) with direct ldap configured.
I am configuring another messaging server (msB.example.com) with smtp authentication for same users to send mail through that and it queries another ldap consumer server (dsB.example.com).
dsB is replicated by dsA immediatly after any modification done to dsA. My present setup works fine if msB is configured on dirsync mode, but I want to configure it to use direct ldap from dsB.
When I try to send email via msB (with direct ldap enabled) it waits a long time after (smtp) authentication and then terminated with "server unexpectedly terminated the connection" message on outlook client. I can not see any message on mail.log_current.
All my direct ldap settings are correct and compiled properly.
Later I found that when I comment the
" $* $E$F$U%$[email protected]$V$H " line on imta.cnf file it works fine, ie. without any delay message is delivered.
(But this has to be uncomment with direct ldap mode according to the sun documentation)
Can anyone clarify this? I could see even without uncommenting the above line direct ldap works fine!

Thanks for replys...
But I tried with the way that you mentioned, but still the problem persists.
No any message on DEBUG logs.
But I have some more thing to tell....
When I first install the messaging server (msB), I used the dsA as the ldap server. So after installation I got gelow results with configutil.
local.ugldaphost = dsA.example.com
local.ldaphost = dsA.example.com
local.service.pab.ldaphost = dsA.example.com
Since I want to use ldap queries from dsB, I change user lookups to dsB
Then the output was,
local.ugldaphost = dsB.example.com
local.ldaphost = dsA.example.com
local.service.pab.ldaphost = dsB.example.com
Do you think this cause thye error?
I can not use dsB for local.ldaphost since it causes the msB not usable. What I only need here is to get the user lookups from dsB.

The Outlook links do not connect to Firefox even after setting the customize option in Default Programs. Please help.

The''' Outlook links do not connect to Firefox '''even after setting the customize option in Default Programs. Please help.

Message to Toad-Hall
Thank you, for that. To be sure, I tried your suggestion, and selected "System Proxy" as the choice, for Thunderbird and Firefox. Rebooted, and looked at the outcome.. NO Joy.. :-(
I believe that I shall send the output of the Error Log in my next post. Perhaps someone can point me in the right direction after looking at the Error.log.
Thank you...Toad Hall. If you think of something else to try, I am ALL ears.. I shall keep trying..

Error after setting up direct LDAP

Similar Messages

Maybe you are looking for