Error alert on my WLC.

We getting the below mentioned error continuously on the WLC when WIFI Voice phone associating with WLC - code(7.0.116.0) and phone firmware
1.3.4
Logs below:
*apfReceiveTask: Sep 28 08:20:17.937: %APF-3-USER_DEL_FAILED: apf_ms.c:5743 Unable to delete username VOICE-PHONE for mobile 00:22:00:11:cf:15
The documents says this mostly occurs due to incompatibility on the client side.
Below mentioned activites has been performed
1,Check if the client is Wi-Fi certified for WPA2 and check the configuration of the client for WPA2
2, Check the data sheet in order to see if the client Utility supports WPA2. Install any patch released by the vendor to support WPA2. If you use Windows Utility, make sure that you have installed the WPA2 patch from Microsoft in order to support WPA2
3, Upgrade the client's Driver and Firmware.
4, Turn off Aironet extensions on the WLAN.

Are all the phones using the same username ?
Are you sure that you allowed multiple logins with the same username (option under the security tab) ?
If you reboot the WLC, do these messages go away ?

Similar Messages

IPod Touch cannot be synced because of unknown error alert (-50)

i connect my ipod touch on my lap top and i cannot sync my photos cuase an unknown error alert (-50)
but on the ipod settings shows like it sync the photos but i cannot see it
how can i fix it?

Hi,
Does the issue occur while syncing photos?
If it does try deleting the iPod photo Cache from the root of the folder photos are synced from, as described here: http://support.apple.com/kb/TS1314
Also, make sure you have the latest software updates available for your Mac. Just click the Apple(top left corner of the scree)> Software Update..
-Jason

When i try to download 'Get album artwork' I receive error alert with (-609) I have tried to download the artwork on the advanced tab, but still no success. My computer runs Windows 7 and the alert appears in my itunes which on my computer.Can you assist?

When i try to download 'Get album artwork' I receive error alert with (-609) I have tried to download the artwork on the advanced tab, but still no success. My computer runs Windows 7 and the alert appears in my itunes which on my computer.Can you assist?

Perhaps try the "Error -609" section in the Specific Conditions and Alert Messages: (Mac OS X / Windows) section of the following document:
iTunes: Advanced iTunes Store troubleshooting

How to send Run time errors alerts to email ?

Dear Friends,
I am using SAP CRM ABAP 6.0. I am checking run time errors in ST22 transaction. Usually, i check in morning or evening, based on my free time. I feel, dificully in this. so, i need to configure in somewhere for send this runtime error alerts to my office mail id.
We are sending report outputs to our office id. But, i dont know, how to send run time errors with log or with out log to emai id?
thanks in advance.
Rajagopal
Chennai - INDIA

Thanks Dieter.
Now, i have set the background job as per your suggestions. but, i have below doubts:
1. I added my office mail id in spool list receipient. This background job alert mail goes to business work place inbox (SBWP). But, i need, in my outlook mail box.
2. This background job gives all months runtime errors. but, only i need today & yesterday only. I checked in ST22 for create variant. Unfortunately, i did not get option. so, how to set variant?
Thanks in advance.
Rajagopal
Chennai - INDIA.

How to clear Error alerts ORA-01219 on standby databases

Hello all
I'm using EM 10.1.0.5. Some weeks ago, we did an upgrade of our standby databases to 10.2.0.4. At that moment, we got many alerts of type Error: ORA-0219: database not open, queries allowed on fixed tables/views only. That's right, these databases are not open. Now I'm getting tired of seeing these 130 messages every day, I would like to delete them. But I cannot ! I removed several alerts of type Warning by setting the threshold value of the metric to NULL and then back again. This works fine. But I cannot use the same procedure for Error alerts, because I do not find these metrics. Example: the metric Streams Capture Message Statistics is displayed on the All Metrics page, but NOT on the Metric and Policy Settings page (selecting All Metrics in the drop down list). Apart from upgrading the EM to 10.2.0.4, is there a way to remove these Error alerts ?
Thank you for any advice
pher

I have checked my 10.2.0.4 OMS and the "Streams Capture Message Statistics" metrics are not displayed on the Metric and Policy Settings page either. This looks like it could be a bug. You might bnefit from raising an SR with Oracle support. In the meantime I will continue to seek a resolution.

Project Load: Error Alerts Suppression Feature

I don't believe there is, but does anyone know of a way to suppress error alerts when loading a project that's missing plugins, can't load a mov file, etc...?
I've already filed a feature request for this and would love if others would too. This has been a big annoyance for me on a large project. Having to click Ok on 20+ alert popups is unnecessary and mind numbing to say the least when you are trying to get in and out of a file quickly. After Effects should simply log all of the errors and create an Error log text file and after the last error just before project is ready to open show one simple alert stating that there were errors and to check out the log for details, or even a small summary of the errors in ONE alert popup. If there is an error, I get it, no need to announce every single one and force me to Ok it. Just give me a list of the problems. Faster, more organized, and just simply a better user experience.
https://www.adobe.com/cfusion/mmform/index.cfm?name=wishform
This is what I filed:
*******Enhancement / FMR*********
Brief title for your desired feature:
    Error log text file for project load errors.
How would you like the feature to work?
    When opening a project that has errors with files, missing plugins, etc... errors of any kind. It would be extremely valuable to consolidate those alert warnings into one single txt log file for easy review and only have ONE alert that either gives a summary of the errors or states that an error log was created in the parent folder of said project file.
Why is this feature important to you?
     Getting a single alert popup for every single error is extremely annoying and in most cases takes way too much valuable time to babysit and click "Ok" for every alert. This annoyance is amplified by not having a printed summary to review afterwards if there are lots of errors or missing plugins.

This is the primary one that I have been dealing with a lot. It's Avid media conversion files that are hit and miss on mac it seems. I have lots of composition timelines that were built via AAF through Auto Duck and these timelines need to stay present in my project. So I have to deal with 10 - 30 of these alert popups each time I open a AEP file, due to the number of mov's in the AEP file. Stuff like that is what makes no sense. Consolidate all errors into one notification, preferrably something tangable like a simple text document so it can be easily reviewed and delt with if need be in addition to the alert popup.
Also after opening another AEP that had missing plugins, I now see the new consolidated alert for missing plugins. Many thanks, that really helps.

FRM-40405: No change to apply. Error Alert.

The first time a detail is updated this message does not display.
The second time a detail is updated, this message displays when the form_commit (or COMMIT) trigger fires.
The alert fires even when a new master record with new details has been queried.
A form level or block level ON-ERROR trigger does NOT intercept this alert. It does intercept other errors like navigation past the first record error or the out of range error.
Where is this error generated? Is it caused because we are using a ref-cursor stored procedure?

That message is issued as a result of a Post; command, not a commit.
Look for a stray post command in your form.
And it can ONLY be handled by an on-error trigger. Please post the code in your on-error trigger.
Also, do not create an On-Error trigger at the block level. (That may be why your trigger is not intercepting it.) From the Forms On-line help:
In most cases, On-Error triggers should be attached to the form, rather than to a block or item. Trapping certain errors at the block or item level can be difficult if these errors occur while Form Builder is performing internal navigation, such as during a Commit process.

Error when adding a WLC to WCS

When adding a WLC to WCS I get this error: Failed to add device to WCS Reason:
COMMON-1: Some unexpected internal error has occured. If the problem persists please report to the Tech Support.
WCS 7.0.164.0 was upgraded from 5.2.110.0 because the WLC were running 7.0.98.0
WLC4404-100 7.0.98.0 (Already in WCS)
WLC4402-12 7.0.98.0 (Changed the ip address of the management and ap manager. Was in WCS but deleted from WCS prior to the ip address change and prior to the WCS being upgraded)
I know that the snmp strings are fine and that the WLC's both respond to snmp get commands.
The intial WCS upgrade from 5.2.110.0 to 7.0.164.0 didn't require the previous version to be uninstalled. After the upgrade and restoring the WCS from backup. I was getting the error posted above. We uninstalled WCS and re-installed WCS from scratch and still we are getting the same error. We tried restarting the WCS services and also the VM box as well and not luck. I was wondering if the WCS has the old ip and mac address of the WLC4402-12 in the database and that is why i'm getting this error.
I did delete and try different snmp community strings with no luck with WCS. Again, snmp is working since I can do snmp get from the WLC's.

Scott,
This is the issue:
com.cisco.common.persistence.transaction.TransactionException: Null value was assigned to a property of primitive type setter of com.cisco.server.managedobjects.aaa.GuestUserTemplateCG.userStatus
Could be an existing bug or a new one. I cant say unless I look into your setup.

Message Mapping error Alert in Email...

Hi All,
Continuation of the thread.
Email Alert Configurationu0085
I need to send a email if we get any error with the mapping.
I configured the ALRTCATDEF and other as mentioned in my earlier thread.
While testing the Alert in <b>SE38 using the program RSALERTTEST</b>. Getting the Email alert as a test and getting the same in RWB Alert Inbox too. But while exicuting in the real time scenario if any mapping fails their is no alert is processing in the Email or Alert inbox in the RWB.
What type of the RFC have to create. Is it TCP/IP or Abap Connections?
Let me know what I have to check and to resolve this issue.
Thanks,
Jane.

Hi Praveen,
Right now it seems to be the different error I am getting.
Error     9/25/07 2:17:15 AM     46f7dfe4-b1a2-612e-e100-0000ac1d0612     Message processing failed. Cause: com.sap.aii.af.ra.ms.api.RecoverableException: java.io.IOException: server does not support PLAIN or LOGIN authentication
Error     9/25/07 2:17:15 AM     46f7dfe4-b1a2-612e-e100-0000ac1d0612     failed to send mail: java.io.IOException: server does not support PLAIN or LOGIN authentication
     9/25/07 2:17:15 AM     46f7dfe4-b1a2-612e-e100-0000ac1d0612     sending mail ...
     9/25/07 2:17:15 AM     46f7dfe4-b1a2-612e-e100-0000ac1d0612     Message processing started.
It seems to be the mail adapter is down let me know how to up the Mail Adapter.
Thanks,
Jane.

MacBookPro SSD Error- ALERT: The partition map needs to be repaired because there's a problem with the EFI system partition's file system.

MacBook Pro OS x Mavericks. I have Sandisk 256GB SSD and I am getting a below error message.
ALERT: The partition map needs to be repaired because there's a problem with the EFI system partition's file system.
Does anyone know how to resolve this error and fix it ? unfortunately I don't have a Time Machine backup. Thanks!

Have you tried to run the verify/repair permissions and verify/repair disk through the recovery disk? If that didn't work then I would reinstall the OS after backing up. If that still doesn't work I would take it in.

BPM error alert XI3

Hi
I have an asynchronus interface with a target system. I need to generate an alert email to support when I get an error returned in my asynchronous send step. How can I achieve this in the BPM
For example, I get a return error of say HTTP 500 from the target system. Currently the BPM terminates with an error. I need to generate an email from this response. Please advice.
Reg
Abhinav

Dear,
Please refer this link,
[SAP Alert|configure ALERT Notification]
Also check Mobile Push Alert Configuration guide mentioned in note 937659.
Hope it will help you.
Regards,
R.Brahmankar

When I run RSPCM gives error in PC and message error, alert, popup

When I run the transaction RSPCM gives error in process chains and appear several popups, messages, alerts. what can be?

Symptom
The job log of a job contains message 00 517 (Job finished) and message BT
608 (Job status was manually set to 'cancelled').
Reason and Prerequisites
There is a program error in the function BP_JOB_ABORT.
Previously, the function BP_JOB_ABORT did not call the job status check
correctly. As a result, BP_JOB_ABORT may still have set a job that had
already finished correctly to 'cancelled'
Solution
Import the Support Package or implement the correction instructions

Concurrent Error Alert Need to send mail

Hi Everybody,
My Requirement:_
if any concurrent program completed with error, it need to send an mail alert notification to the users.
My Environment:_
OS : OEL4U5
DB : 9.2.0.8
Apps Version : 11.5.10.2 (with ATG RUP 7)
Steps i have done:
1) OS level Mailer configured and am able to send a mail.
2) From the application level regarding workflow notification all the services are up and running and am able the receive test mail from application to my mailer account.
Issue:
For alert configuration i referred this mention meta-link id *"How To Send A Notification For A Failed Concurrent Request [ID 730657.1]"*
But for me it showing an error in alerts *"System Alerts are disabled because of following: Logging is disabled"*
for this log disabled issue i referred this doc but in my case its not worked *"System alerts in OAM are disabled because of the following:Logging is disabled [ID 455937.1"*
Kindly suggest me to step forward
Regards
Athish

Hi ,
Now am able to receive the error concurrent alert to the user mail perodically.
Referred Metalink Doc:
How to send a Concurrent Program Error Exception Report as a notification to users using Alerts [*ID 396756.1*].
Issue Currently Facing:_
If i run the Periodic Alert Scheduler concurret program in alert manager manually am able to receive the error concurret report with log file to the user mail id.
At the same time if i schedule this Periodic Alert Scheduler concurret program for every *10 minutes* am not receving any error concurrent report and logfile to user mail id.
Kindly Suggest me i need to schedule this Periodic Alert Scheduler concurret program perodically for every 10 minutes at the mean time error report mail need to receive for users mail id.
Regards
Athish.
Edited by: Athish on Mar 20, 2012 6:04 AM

Mapping Error Alert Generate by mail.

I have to send one mail, If there is any Error in Mapping & message is in Error in SXMB_MONI.
How I can configure that alert ?

Hi,
There are so many blogs and wiki on the same.
Plz have a look:
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/00e97ba2-85ce-2b10-20bc-bc05cd172154?quicklink=index&overridelayout=true
http://wiki.sdn.sap.com/wiki/display/XI/AlertConfigurationin+XI
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--troubleshooting-guide
/people/pravesh.sharma/blog/2009/07/02/configuration-for-forwarding-alerts-as-emails
Thanks
Amit

Form submittal error alert

I have a form created in Acrobat. I included a
button with the submit form action to submit the entire pdf as an attachment.
It works but after the user submits the email it returns an error "User Canceled Operation. Any ideas?

If you aren't creating the message in your form, then it is the procedure that you are calling. Either way, just rtrim the message when you put it into the alert.
But it would be better to get the person who wrote the original process that generates the messages to clean up their code and remove the trailing spaces at the source.

Error alert on my WLC.

Similar Messages

Maybe you are looking for