Error code 0x80070035

First, I'm really green with the computer stuff. I know a little, but I read thru the other forums and I don't understand some of it. I'll apologize ahead of time.
So, I set up my main computer for networking according to all the wizards. OS=Windows XP. I have a laptop that runs Vista home. My main computer (which I've renamed) shows up on in my network, but when I try to connect, I get the error message error code 0x80070035 network path was not found. All I want to do is share files and the printer.
Any info would help, and again, I'm apologizing now for my computer illiteracy.

Hi,
Thank you for posting.
Based on my research, I would like to share the following:
1.    Ping the computers with each other by IP Address and computer name to see how it works. Access Windows Vista computer’s share with both \\computer name\folder and XXX.XXX.XXX.XXX\folder to see if they are works.
2.    Ensure NetBIOS over TCP/IP is enabled on both computers
====================================================
1)     Go to “Control Panel - Network Connections”.
2)     Right-Click on the connection and click Properties.
3)     Find Internet Protocol (TCP/IP) Version 4 in the list.
4)     Click Properties, and then click Advanced.
5)     On the Advanced TCP/IP settings windows, go to “WINS” tab.
6)     Under NetBIOS setting, click Enable NetBIOS over TCP/IP, and then click OK.
3.    Please ensure the firewall on both computers are set the enable “File and Printer Sharing”.
Hope this helps. Thanks.
Nicholas Li - MSFT

Similar Messages

Error code: 0x80070035 The network path was not found

"Error code: 0x80070035 The network path was not found" while trying to access another PC running Windows 7 Ultimate I searched and read dozens of similiar posts to try to resolve this issue with no success.
The situation is, I have a router in home with 4 PC's connected. My central PC is running Windows 7 Ultimate. The others are Windows 7 Ultimate again, and 2 running XP Pro. No special Firewalls, just have Windows Firewall enabled on all PC's, and am running KasperskyInternetSecurity2010 on all. (Have disabled these on all PC's and tried to view/connect and it didnt make a difference, same error)
Fact one: not attempting a Homegroup connection at all, just simply wishing to connect in a basic network environment where I can drag and drop files between all PC's in my Home Network or in my house , however its considered. But on the Windows 7 I am unable to view either of the XP's only the other Win7, and when I try to access that one is when I get the "Error code: 0x80070035 The network path was not found".
Furthermore, while troubleshooting the problem I opened a Command Prompt in all computers, then an "ipconfig" to view each ip address. Then began to ping each machine to determin connectivity. Which resulted in partial success. My main Win7 machine (which i am on now) was able to ping successfully to all machines. But all other machines were unable to ping to me (main Win7). with a 100% loss.
So at least I determined this is most likely a helpful fact in resolving this. Going into "services.msc" I made sure that all the obvious services are started and running:
DCHP Client, Homegroup Listener, Homegroup Provider, Link-Layer Topology Discovery Mapper, NetTcp Port SHaring Service, Network Connections, Network List Service, Network Location Awareness, TCP/IP NetBIOS Helper
All strarted and running in Automactic mode.
Not sure what other information I can give at this point, to help assist in fixing this problem. Please dont hesitate to ask for me for more info if needed. Ready and willing to try anything to get this working, except for reinstalling the OS. All my programs work great and do not wish to go through the drama ao reinstalling all my programs and activating them and redoing all my Adobe settings and CAD settings.
Someone please help !

Hi,
In addition, I would like to suggest the following:
Enable NetBIOS over TCP/IP:
1.    Go to “Control Panel\Network and Internet\Network Connections”.
2.    Right-Click on the connection and choose Properties.
3.    Click “Internet Protocol (TCP/IP) Version 4” in the list.
4.    Click Properties, and then click Advanced.
5.    On the Advanced TCP/IP settings windows, go to “WINS” tab.
6.    Under NetBIOS setting, click “Enable NetBIOS over TCP/IP”, and then click OK.
Thanks.
Nicholas Li - MSFT

Error Code 0x80070035 - The network path was not found, Windows Server 2008 SP2

I have bee receiving following "error code 0x80070035 - The network path was not found" when trying to open file shares in both directions using Windows Server 2008 Standard SP2 at both ends. The issue is identical to the KB article KB958285, however the hotfix is only valid up to but not including SP2. One of the servers in question has moved several times between 2 subnets seperated by a VPN. I have tried changing settings in and around the local NIC/DNS Suffix and in the network connection sharing centre, but with no luck. Firewalls are turned off at both sites, and pings and AD queries are successful (one server is a DC). DNS is also working correctly at both sites. Any help/suggestions would be appreciated.
Richard

I thought I would add in another scenario, since this link came to the top of my list in the search engine.
We are running 2008 R2 with SP1 (it happened without SP1 as well)
We could not map using UNC (IP, FQDN, or netbios name). We could ping access the other servers via other utils like event viewer and services.msc but just could not map.
In our case it turned out to be a VMWARE issue but we still had to make a regedit change first
You have to go to regedit HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\NetworkProvider\Order\
And add LanmanWorkstation to Providerorder
I found on a Citrix board that citrix has an issue with this as well
If you're running VM here is an additional step you should do as well
When you upgrade VMware Tools installed with HGFS from ESX 3.x to ESX 4.x, the HGFS driver may not get uninstalled properly. In this case, the virtual machine's network Provider Order tab in Network Connections
> Advanced > Advanced Settings displays incorrect information and the virtual machine may lose network connectivity.
To avoid this issue, uninstall VMware Tools 3.x before installing VMware Tools 4.x.
To workaround this issue, if you have already upgraded VMware Tools:
Click Start >
Run, type regedit, and click OK. The Registry Editor window opens.
Navigate to
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\NetworkProvider\Order\.
Delete the reference to
hgfs.
Reboot the virtual machine.
We found that if you strip out the HGFS, you do not have to reboot for the provider order tab to come back
I hope that this saves people a lot of time. I spent days researching this.
This was the solution for me on 2008 R2 DC w/ Exchange. I do not have VMWare installed but do have Hyper-V. Thank you so much!

Cannot access a shared folder Error code: 0x80070035

Hello Experts,
I have been working on this issue for like three days without a solution. I am truly desperate.
My company just purchased a new Cloud Server that we will use as our development environment for a software project. In order for all the developers (which are all over the US) to access the development environment, we need to have a few shared folders on
that new server.
As soon as we got the server I did the following:
1) Installed Active Directory
2) Created a directory and made it shared - yes IT IS shared.
3) I created a few new users on the new active directory domain
THE PROBLEM:
I can't access the shared directory.
Other developers have been successful in connecting to the shared folder (so the share is working) - all except me.
when I open explorer and type \\IPADDRESS\SHAREDFOLDER instead I get this error (I am not even asked for credentials)
Network Error
Windows cannot access \\IPADDRESS\SHAREDFOLDER
Error code: 0x80070035
The network path was not found.
Things I have already tried:
a) Enable NetBIOS over TCP/IP - on all adapters - still did not help
b) Disable IPv6 - I am not sure how to check if it truly disabled
c) Turned off all firewalls - did not help
d) Mapping a Drive using different credentials - I just get asked for credentials over and over
e) Ping - yes I can see the server
f) My credentials are correct because I can Remote Desktop with the credentials with no problem ( I am administrator)
My Machine:
Brand New Asus G Series
Windows 7 Home Edition
Any ideas?
Sorcerdon

In my case it was that the OU that my system was in did not have firewall rules for network file and printer sharing enabled. I enabled all of the rules for Domain policy and that fixed it.
I noticed a lot of comments about turning off the firewall not working. I can't be 100% sure, but in my experience with Server 2008 and Windows 7, if you want to configure a service that uses the network the base filter engine and the firewall HAVE to be
turned on while you configure. You can turn the firewall off after configuration, but they have to be active during configuration.
Good luck!

Network error code 0x80070035

Hello
I have router Siemens SE555 with USB File server enabled and i have one disk connecetd on it. On Windows 7 when I wont to access to disk I get massage Windows cannot acecess \\NetworkDisk. I also have one PC with Windows Vista Business and one with Windows XP and both off them can access to that disk.
I get code: Error code: 0X80070035 The network path was not found.
Please if anyone can tell me what to do?
Thanks

Since you are able to see and access Computer 2 from Computer 1 and unable to see computer 2 from computer 1. I would suggest you to first check with both the computer if the Network discovery is turned on both the computer.
To turn on network discovery
1.Open Advanced sharing settings by clicking the Start button, and then clicking Control Panel. In the search box, type network, click Network and Sharing Center, and then, in the left pane, click Change advanced sharing settings.
2.Click the chevron to expand the current network profile.
3.If network discovery is off, under Network discovery, click Turn on network discovery, and then click save changes. If you're prompted for an administrator password or confirmation, type the password or provide confirmation.
Also you may access the link and follow the steps and check if it helps to see the computer 2.
http://windows.microsoft.com/en-us/windows7/Why-can-t-I-connect-to-other-computers
Also you may verify if you can access computer 2 from computer 1 by opening with the run command and typing the IP address of computer 2.
To do this, follow the steps in computer 1.
1. Click on Start
2. In the start search box type \\ipaddress\ of the computer 2 and press enter eg: \\192.168.0.2\
Check if this opens and connects to Computer 2 in the network.
Also you may try to boot both the computer in safe mode with networking and see if they are able to see each other. To boot to the desktop in safe mode with networking keep tapping F8 key during restart. Once you see the option to boot in safe mode with
networking select it and press enter.
Access the link to know more about how to boot the computer in safe mode:
http://windows.microsoft.com/en-US/windows7/Start-your-computer-in-safe-mode

Error code 0x80070035 on drive maps in GPO, "Network path cannot be found".

I am trying to apply a GPO that maps drives so that another GPO can then make them available offline for a couple of hundred users.
Every time I try to apply the policy it fails with an 0x80070035 error which translates as a "Network Path cannot be found". The security settings for that particular folder is fine and the user can see it ok, furthermore following logon I can
manually map the drive through windows explorer and through CMD/powershell using the net use command.
The path i tried was \\servername\otherdir\securearea\ which didnt work (i did drop and add the final "\" just in case i was going mad)
i then tried \\servername\otherdir\unsecurearea\ which
still failed
just to prove my lack of sanity i created a folder on the hard drive of the laptop itself, made it a shared folder and tried both \\localhost\sharedfolder and \\127.0.0.1\sharedfolder,
they all fail with the same error code.
i have checked the hosts and the lmhosts files are there is nothing new in there, only the usual MS gumf that has come with every copy on windows since Win95
patience is wearing thin, hair is getting short ...
thoughts anyone?
Nothing is unfixable - with a suitable sized hammer!

Hi klimacher,
Would you please let me know the current situation of this issue? Have you referred to Kelly's suggestion and solved this issue?
Based on your description, I understand that you configure Drive Maps via GPP. However, can’t apply the policy
with error code 0x80070035. If anything I misunderstand, please don’t hesitate to let me know.
If so, you should find Event 4098 as below shows.
When you type the location of this mapped drive, please remove trailing slash on the UNC path. Then apply the
setting and run gpupdate command to update group policy setting. Please monitor the result.
In addition, please refer to the following article and troubleshoot this issue.
Troubleshooting
the Drive Maps Preference Extension in Group Policy: Adding a Share Name with Trailing Slash '\' Returns Error Code 0x80070035
If this issue still exists, please let me know summarily how you configure the Drive Maps. For an example,
where the GPO link? Did link to user OU? Any update, please feel free to let us know.
Hope this helps.
Best regards,
Justin Gu

Error Code 0x80070035 shows when I try to Access Windows XP machine from Windows8/Windows7

Error Code 0x80070035 shows when I try to Access Windows XP machine from Windows8/Windows7. in my PC i m installed windows8 and used primary and secondary IP. Primary is used for Access my Domain/Internet and secondary IP is used for access my VPN and
there is no internet on VPN. VPN is only used for my Head Office Appication. After i give secondary IP to my windos8/windos7 PC the Active network status changed to private network and not able to acces windows XP machines. Please Advice...

Hi,
This error means that the Network path was not found. Was Windows XP locating in the same network as the secondary IP on Windows 8/7?
Please try the solution below. Use the IP address of the target computer, not the computer name.
1) Find out what the target computer's IP address is. It is desirable to give the target computer a static private IP address, for example, 192.168.1.10, so it does not change. Use the local windows help when sitting in front of the target computer
to do this if you don't know how.
2) When sitting in front of the Windows 7 computer you want to access the target computer from, open Windows Explorer and in the address bar type \\ followed by the target computer's static address, for example,\\192.168.1.10 and hit enter.
If the target computer uses username/password sharing, after a few seconds you will be prompted for credentials. Enter the same username and password employed to log on to the target computer when you are sitting in front of it.
The target computer will be added to the Windows 7 computer's Network list, appearing as an IP address instead of a computer name. Then you can access its shares just as if it were listed by name instead of by number.
Kate Li
TechNet Community Support

Cannot delete file from external hard drive (error code 36) in Finder, but Terminal is ok

I have a relatively new Macbook Pro Retina 15" and have a Western Digital 1 TB Passport. I've been using the passport for about a year now without any problems on older Macbooks in my house. I used to be able to read and write to this drive no problem. I am using the Paragon NTFS for Mac software in order to read and write to the NTFS drive. When I navigate through the drive in Finder, if I try to create a new folder, I do not have a problem. If I try to delete that folder I just created, I get this error:
The Finder can’t complete the operation because some data in “untitled folder” can’t be read or written.
(Error code -36)
The folder has nothing in it whatsoever. I just created it. But if I go to Terminal and I run
rm -rf "untitled folder"
This works fine. Why is Terminal acting different than Finder? This does not happen on my other Macbooks. Thanks in advance.

Thanx for such qucik reply!!! The pages were great, it had an answer for my problem, but unfortunately it also involved me dealing with it only on the MacIntosh HD itself, not on mounted external drive I suppose... So it didn't work they say that there is an icon in the left corner indicating locked folder - I don't see any icon on it. It says you can untick the box to unlock the folder - there is no tick to be unticked. Finally, they say that if I don't have permition or rights I cannot delete it. But how do i change permittion which already says that i can read and write in it? So everything appears to be normal only I cannot delete it. there is not even any warnig telling me I don't have enough rights, it just requires the password and after me typing it in it makes the sound of scraping paper but does nothing more. I aslo had some problems with emptying Trash after being seemingly succesful with one file and had got so far to have them appear in the Trash (no clue how this one actully got there though..) I followd the advice and emptied the Trash with Terminal. The Folder is still there but it shows 0 Kb... So far so good BUT: It is still on the external drive, so I obviously only managed to copy it into the Trash!!! Phew, innit a bit too tight to poor owners, this macbook?? I want my rights back!

Report generation failed----error code:-17205; Access Denied.

Hi, All
    i have a trouble about report generation.it seems the error happened at the "write UUT report"--this step is teststand report generation'DLL.
    detail:
    An error occurred calling 'Save' in 'Report' of 'NI TestStand 2010 SP1 API'
Access Denied.. Error writing to file 'D:\program\seq\xxx.xml'.
The file might be open in another application. If file access is intermittently denied, you should try disabling the Microsoft FindFast utility.
    error code:-17205; Access Denied.
    locationtep 'Write UUT Report' of sequence 'Single Pass' in 'SequentialModel.Seq'
    How to fix it?
    Thanks a lot.
BR

Hm, it looks like the file might be open in another application. If you see that file accesss is intermittently denied, you should try disabling the Microsoft FindFast utility.
CTA, CLA, MTFBWY

There was a recent upadate on my PC, however it does not work. A error code comes up which says, min version is not compatible with max version. And I caanot open my browser. Please help.

I do a system restore which allows me to open my browser. Without this I cannot open my browser - the error code comes up every time.

Do a clean (re)install
* Download a fresh Firefox copy from http://www.mozilla.com/firefox/all.html and save the file to the desktop.
* Uninstall your current Firefox version and remove the Firefox program folder before installing that copy of the Firefox installer.
* Don't remove personal data when uninstalling.
* It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
From https://support.mozilla.com/en-US/questions/764376

My ipod touch is not list as a device on itunes. When I tried do update itunes, I get a ox8007054f error code and the update will not complete.

My ipod touch is not listed as a device when connected to my computer. As suggested I attempted to download the latest of itunes. I got an
ox8007054f error code and the down load will not complete. I have also tried to restore my computer to an earlier setting, but it will
not accept the change.

Have you looked at this completed previos discussion. It discusses 0x8007054F.
Re: Error message when trying to install iTunes

Capturing oracle error codes into a variable

Hi
Can someone show me how it is possible to save an Oracle defined error code into a variable? What I am trying to do is when a stored procedure fails an Oracle error is raised, such as ORA-xxxx, then pass this code into variable to be saved into a log.
How do I achieve this?

user633278 wrote:
How do I achieve this?Function SQLCODE in PL/SQL exception handler returns error code. SQLERRM returns message:
SQL> declare
2      x number;
3 begin
4      x := 1/0;
5    exception
6      when others
7        then
8          dbms_output.put_line('Error code: ' || SQLCODE);
9          dbms_output.put_line('Error message: ' || SQLERRM);
10 end;
11 /
Error code: -1476
Error message: ORA-01476: divisor is equal to zero
PL/SQL procedure successfully completed.
SQL> SY.

Error Code:942 While Scheduling a report in BI Publisher

Hi All,
I am trying to schedule one report in BI Publisher.
After Clicking Submit Button while scheduling report,i get following error:
Exception [TOPLINK-4002] (Oracle TopLink - 11g Release 1 (11.1.1.0.0) (Build 080319)): oracle.toplink.exceptions.DatabaseException Internal Exception: java.sql.SQLException: ORA-00942: table or view does not exist Error Code: 942 Call: UPDATE SEQUENCE SET SEQ_COUNT = SEQ_COUNT + 50 WHERE SEQ_NAME = 'JOB_ID_SEQ' Query: DataModifyQuery()
Kindly Help me in resolving this issue
Regards
Amrita Singh

i know the issue,i can give quick fix, but in-order to make sure you don't get another glitch like this.
I would recommend, you to install the scheduler in another schema or another db.
Re-installing the scheduler schema tables will fix this.

ORA-00600: internal error code, arguments: [ktsircinfo_num1]

While taking export of a table received EXP error and while dropping/selecting the same gor ora-600 errors.
. . exporting table TEST4
EXP-00003: no storage definition found for segment(29, 371385)
SQL >Drop table test4 cascade;
ORA-00600: internal error code, arguments: [ktsircinfo_num1], [29], [29], [371385], [], [], [], []
sql> Desc test4;
ORA-00600: internal error code, arguments: [ktsircinfo_num1], [29], [29], [371385], [], [], [], []
I dont want to log TAR with oracle right now... I tried dropping and recreating Undo tablespace but still did not help much . Database version is 9204

hi
read metalink ID - 153788.1
CHeers

Transport control program tp ended with error code 0212

Hi all,
I have created a two system landscape of development & production server. But while I am releasing any request from develpoment server a error is showing: " Transport control program tp ended with error code 0212 Errors: could not access file as supposed (see dev_tp or S".I have chosen development server as domain controller. TMS alert viewer error message also contains the following information------>command: TMS_MGR_READ_TRANSPORT_QUEUE
                                                                       service: transport service
                                                                       start : online
                                                                       Function: TMS_TP_SHOW_BUFFER
                                                                       message: TP_REPORTED_ERROR
In import monitor it's showing : "tp finished: could not access file as supposed (see dev_tp or SLOG1113.K"
Can you tell me how to resolve this issue?

dev_tp contains:
This is R3trans.exe version 6.14 (release 700 - 09.04.10 - 11:26:00).
unicode enabled version
usage: R3trans.exe [<options>] <control_file>
The control_file describes what R3trans has to do.
The following options are possible:
-c f1 f2 : Copy file f1 to f2 with character set conversion.
-d       : DB connect. Test if SAP database is available.
-i file : Import from file without using a control file.
-l file : List the contents of file to the log file.
-m file : List the contents of file to allow tp to create a cofile.
-t       : Test. All database changes are rolled back.
-t4      : Trace level 4. Switch on developer trace.
-u <int> : Unconditional modes. See below.
-v       : Verbose. Write more details to the log file.
-w file : Log file. The default log file is 'trans.log'.
-x       : DB connect without access on any SAP table.
R3trans.exe finished (0012).
& the slog file is not there in the trans/log directory

Error code 0x80070035

Similar Messages

Maybe you are looking for