Error code "-1" while updating the iOS from IPAD2

When I try to update my IPAD2 to iOS 4.3.2 I receive the error code "-1" at the end of the installation, and now I´m stuck in the restore point, because the system don´t boot anymore. When I connect to Itunes it says I have to download the update, then the error appear again, and this is going over and over... Any hints here?

i dont 'now whay people of apple company not concern about this probleme .
i am facing the the same that you have . no one answer . please good felwo help us

Similar Messages

Does anybody know the error code 11 while updating to ios 4.3.3.? thx

does anybody know the error code 11 while updating to ios 4.3.3. on an ipad1? thx

but my hard drive is still lot of spaces...still keep on trying to update...

Error code 0x80240031 while updating to 8.1

From last 20 days I am facing this error code 0x80240031 while updating to 8.1 sharp at 50% ...tried almost 50-60times on my ... G500s ... pre-installed os .... I contacted both Microsoft and Lenovo for this issue ... both of them tried to solve it ... Microsoft suggested me to reinstall the whole os. So I contacted Lenovo for the same ...they reinstalled it ... BUT STILL THE PROBLEM EXISTS.... I don’t know what to do m very frustrated ... should I sue Microsoft for not solving or Lenovo..... Because if this issue won’t get solve... I might have to take some legal source to solve my case ...I tired every option available on the web .....as i cant even get an new windows key or DVD...

I tried everything on that link... but still facing the error...
command prompt and type/run: "sfc /scannow" ...no problem
Dism /Online /Cleanup-Image /RestoreHealth.... no problem
Antivirus ..uninstalled .....
i tired the every possible thing on this webiste also
1. http://answers.microsoft.com/en-us/windows/forum/windows8_1-windows_install/windows-81-update-error-...
2. http://www.thewindowsclub.com/error-code-0x80240031-updating-to-windows-8-1

Iphone hung while updating the ios what should i do ?

iphone hung while updating the ios what should i do ?

Placing your device into recovery (DFU-Device Firmware Upgrade) mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
   1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
       other end of the cable connected to your computer's USB port.
   2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
       until the red slider appears, then slide the slider. Wait for the device to turn off.
              * If you cannot turn off the device using the slider, press and hold the
                Sleep/Wake and Home buttons at the same time. When the device turns off,
                release the Sleep/Wake and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the
       device. The device should turn on. Note: If you see the battery charge warning,
       let the device charge for at least ten minutes to ensure that the battery has some
       charge, and then start with step 2 again.
4. Continue holding the Home button until you see the "Connect to iTunes" screen.
       When this screen appears you can release the Home button:
5. If necessary, open iTunes. You should see the following "recovery mode" alert:
6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

Extraction time while updating the data from update rule

Hello Friends,
Can you please tell me that why it is taking more time while updating the data from update rule to data target.
I believe that it is taking 40% of total extraction time.
Is there any specific reason for it?
Prompt reply will be appreciated.
Regards,

hi,
check if you have complex transformation in that update rules, like calculation, read from other tables, etc.
take a look 'bw loading performance and analysis' doc
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/1955ba90-0201-0010-d3aa-8b2a4ef6bbb2
and bi performance tuning knowledge center
Business Intelligence Performance Tuning [original link is broken]
there e-learning for bw performance
hope this helps.

My iPhone 4S has locked up while updating the ios. what do I do?

my iPhone 4S has locked up while updating the ios. what do I do?

Reset your device: hold down the home button along with the sleep/wake button until the screen goes black and you see the Apple, then let go. Then try it again.

Error code 6 when updating to iOS 7

Hi, I have a fairly new iPhone 4S which had behaved impeccably, bur when I came to update the iOS to 7.0, through iTunes, error code 6 was returned. I had to restore to factory settings, which gave me the new iOS and then I had to restore all apps etc from my last back up. The same thing happened when I updated to iOS 7.02. I have an iPhone running the latest iOS and it's working fine, but if I have to do this everytime there in an incremental iOS update it's going to be really annoying having to set the iPhone aside for a few hours rather than a few minutes.
I've read the Apple Support docs realating to error code 6 and can't really make any sense of it. Also, it's predominantly aimed at Windows users.
Can anyone help me?

Hello Phillips, this error usually has to do with Jailbroken iphones, just need to go into DFU mode then restore and update. Hope this helps.

Why is the Error Code 0x8002006E While Burning the Disc?

Hey there! I don't seem to get through this Issue. I was trying to burn content to a Disc and it failed with the error code 0x8002006E, while the process was almost complete. I came across a few forums and nothing helped much to resolve this problem. Is there someone who knows the exact cause? Is this is a known-issue or anything already being addressed by Apple? Or a work-around to get this resolved? because i also read (did not try) that no third-party applications, as an alternative, solved this Issue. Disappointed! Help!
Model: iMac (21.5-inch, Mid 2011)
OS: Lion OS X 10.7.4
I have the latest software updates and Firmware updates installed.
Thank you,
Sivarama Krishnan (kvsrkrishnan)
<Edited by Host>

I found this article excerpt:
The few solution that where found where by calling at Apple and get technical support. There are a few solutions that might work.
The first one would be Go to users > your computer name / user name > library > Preferences > com.apple.finder.plist and delete this file. Also it’s advised to keep the burn speed at 8x.
The second solution found that Apple technical support gave is to unplug everything, including the AC power cord and then remove the battery. Press the power button for 10 seconds without replacing the battery or attaching the AC power cord and after the 10 seconds are up replace the battery. After the battery is in slot hold down the following keys with the left hand: Option + Apple (command) + R and with the right hand hold down the following keys: P + Power Button. You will need to hold all 5 of these buttons at the same time until you hear both sets of startup chimes Release all of the 5 buttons after you hear the two startup chime sounds.
Hope this helps

While updating the software from 6.1.3 to 6.1.4 on iPhone 5, the power failed. iTunes had just finished the backup and was beginning the software update. Now the phone screen says to connect to iTunes but the phone is not recognised when plugged in.

While updating the iPhone 5 software from 6.1.3 to 6.1.4, the power failed. iTunes had just finished the backup and was beginning the software update. Now the phone screen says to connect to iTunes but the phone is not recognised when plugged in. Using Windows 7 and phone not recognised by computer, let alone by iTunes.
Any suggestions? Happy to take it off to the the Apple genius people but would prefer to get it running myself.
Regards.

Try this
iOS: Device not recognized in iTunes for Windows

HT4623 I am getting an error messae when I update the iOS

I am getting an error messae when I update the iOS

Sorry don't recall. But it's OK. working now. Thanks for responding

Receiving error code 3194 during update to iOS 4.3.3 on IPad

Every single step is taken into account like admin rights, running Itunes in admin mode etc. etc.
Still its not possible to update the iOS 4.2.1 into iOS 4.3.3 on an IPad 1.
WHAT TO DO ???

This page suggests that updating to the latest version of iTunes should help : http://support.apple.com/kb/TS3694

URGENT : ERROR 18 while updating the Infocube from ODS....

Hello
We got the data into BW from MS SQL. There are 19 Datasources and we used views for all. Using 19 child ODS objects we updated 3 Parent ODS Objects.
Now we have to update the 3 ODS objects data to the InfoCube. When we try to Update its giving the error
"ERROR 18 in the Update" and some hexadecimal error message in the data, but we can only find the error like IV hexavalue inbetween the words(the InfoObject data type is CHAR) and in some errors we cannot find any mistake. It is just like normal text.
What could be the problem ?
Best Regards....
Sankar Kumar
+91 98403 47141

Dear Sankar Kumar,
I think this is related to Invalid character issues.. or SPaces setting in RSKC..
may be you want to look at eh following post..
Re: invalid characters
/people/siegfried.szameitat/blog/2005/07/18/text-infoobjects-part-1
Example:
let us say..
1. Check in RSKC for allowed characters..
2. Add a code in the update rule to restrict the texts contains..
!"%&''()*+,-./:;<=>?_0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ' are allowed characters in RSKC transaction then other than the above character is 'Invalid' including the smaller case letters and will throw the hex.. error.
since this is from database system even 'NULL' datatype from there is not visble to the eyes and can cause the failure.
regards,
Hari

Error code 3014 when updating new IOS

I tryed to update my iPhone 4s to the new software 6.0.1 this evening and now m iphone is a brick. I am unable to update

Error 3014 means the following:
Errors 3000-3999 (3004, 3013, 3014, 3018, 3164, 3194, and so on): Error codes in the 3000 range generally mean that iTunes cannot contact the update server (gs.apple.com) on ports 80 or 443.
Update to the latest version of iTunes.
Verify the computer's date and time are accurate.
Check that your security or firewall software is not interfering with ports 80 or 443, or with the server gs.apple.com.
Follow Troubleshooting security software. Often, uninstalling third-party security software will resolve these errors.
An entry in your hosts file may be redirecting requests to gs.apple.com (see "Unable to contact the iOS software update server gs.apple.com" above).
Internet proxy settings can cause this issue. If you are using a proxy, try without using one.
Test restoring while connected to a known-good network.
Error 3014 may indicate that you need to free up more disk space on the computer before trying to restore again.
Here's the article containing the above: http://support.apple.com/kb/TS3694

Error code A12E1 while updating Creative Cloud

Hello,
The title of this topic says enough, I think. While updating Creative Cloud I get an error code A12E1. What is this and how can I fix this problem?
Thanks!

Hi Niels Joormann,
Please follow these steps to fix this issue.
Please launch task manager and check whether any Adobe updater or Acrotry process is running. If yes please close them before you perform these steps.
Download and run Adobe Creative Cloud Cleaner Tool. You can download it from this Website
http://www.adobe.com/support/contact/cscleanertool.html
Once done please rename OOBE Folder to OOBE.old from the mentioned location.
C:\Program Files (x86)\Common Files\Adobe
Download and Install Creative Cloud Desktop App from this Location
https://creative.adobe.com/products/creative-cloud
If none of the above steps work then please create another Admin user Account and try to install Creative Cloud Desktop app there.
Please let us know if it helps.
Regards,
Abhijit

Why I encountered error code 50 while installing the app?

I was using the trial version and just purchased the app via online. However ,when I try to install the desktop app, it shows error code 50 in which it encountered issue while installing.

For Windows :
1)End all Adobe process from Task Manager
2) Open C:drive and navigate to C:\Program Files (x86)\Common Files\Adobe.
Open Adobe folder and delete folders named Adobe Application Manager and OOBE.
3) Navigate to C:\Program Files (x86)\Adobe.
Open Adobe folder and if present delete Adobe Creative Cloud folder. [ Important step]
4) Press Windows button (located between Ctrl and Alt buttons) along with R button together at a time , you will get a run command window.
Type in below command and hit 'Enter' key.
appdata
Then navigate to Local>Adobe.
Open Adobe folder and delete folders named AAMUpdater and OOBE.
5) Click on the below link and download Creative Cloud setup file and use the same to install the Creative Cloud Desktop application.
https://creative.adobe.com/products/creative-cloud

Error code "-1" while updating the iOS from IPAD2

Similar Messages

Maybe you are looking for