Error code (-1302)/ firewire cable?

I got a new color iPod and installed iTunes 4.90.17 but I get an error message box (2 of them the same) that says:
iTunes error 1302: "the disc 'content' cannot be read" unexpected error 1302
I click OK on both boxes and then iTunes comes up and works OK: how can I resolve these error codes? Win XP/USB 2.0. I have tried reinstalling iTunes but the error boxes always come up
also I had trouble with USB: I have a firewire port: what cable do I need to buy for firewire?
Thanks!!!

Has anyone come up with a solution to this problem? I only began to see this after I upgraded to iTunes 5.0 and now I constantly get a Windows message saying "An unknown error occurred (-1302)."
My songs continue to play, but I get this same message every ten minutes or so and always in a series of two or four.

Similar Messages

Spartan 3E with Labview 2012 (32 bit) on WIndows 7 64-bit - Error Code: -310602 NI-COBS: Unable to communicate with device over communication cable.

Thanks for the info, Kyle. I will probably try to find an older 32-bit XP machine. VM is just not an option for me right now.

Hello everybody,
I am trying to use the DIgilent Spartan 3E board with Labvew 2012 SP1 32 bit. I am able to compile the example code for LED shift. I am however unable to transfer code to the FPGA. I get the following error message:
Error Code: -310602
NI-COBS: Unable to communicate with device over communication cable.
Please verify that the cable is connected to a supported device and that the appropriate drivers are installed.
My system configuration is as follows:
Windows 7 (64 bit) on Dell XPS laptop.
Labview 2012 SP1 (32 bit)
Labview FPGA 2012 SP1
Labview 2012 FPGA support for Spartan3E
Xilinx 13.4 tools
DEFB LV FPGA 2012sp1 support installer
Xilinx USB cable driver v1.3 installed.
I took all the precautions mentioned by others on this forum and others, mainly that the cable must be disconnected before installing the Xilinx cable driver. All software and drivers were installed correctly. I even uninstalled and reinstalled the entire Labview software set I had. I still get the same error.
A few other questions:
1. Is the Xilinx cable different from a regular USB cable of the same configuration ?
2. When I program the FPGA I only have the USB cable connected between my computer and the Spartan 3e board. Should any other cable be connected ?
3. What should be the correct jumper settings for J1 - JP30 (especially J30, J11, JP9, JP6, JP7, etc) ?
I have been at this or over 3 days trying to figure it out. Any help will be greatly appreciated.

TS3694 When i plug in my Iphone to restore it, itunes gives me error code 2009. All i have on my iPhone display is the itunes logo and the usb cable.

When i plug in my iPhone to itunes so i could restore because i found it, itunes gives me error code 2009. on my iPhone, all that is displayed on the screen is the itunes logo and a usb cable saying to connect it to itunes. Help please?

Error 2000-2009 (2001, 2002, 2005, 2006, 2009, and so on)
If you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore. If you are using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore. If that does not resolve the issue, try the USB issue-resolution steps and articles listed for Error 1604 above. If the issue persists, it may be related to conflicting security software.

Error: Account 900000 in company code 1302 cannot be directly posted to

Hi firends,
When I tried to release to accounting in VF02 tr.code, It gives me error message about "Account 900000 in company code 1302 cannot be directly posted to ". In G/L account settings, post automatically only is not checked in create /bank/interest tab. In type/description tab, account group is choosen by recon.account ready for input .
take your opinions...

Is it recon account , if yes then,
It is clear what the system says: You can not make manual Journal Entries to a Reconciliation Account.
If you need to post manually to this account you need to change from from Reconciliation to a normal account. I would not recommend if this is a real reconciliation account, thought.
Have u set up revenue accounts (VKOA)?
And always try to mention the error message while posting.
Check and revert back.
Regards
Ashu

Firewire Error Code -1309

Hi
This is more a Firewire question which is tangentially
related to Final Cut Pro
I have encountered "Error Code -1309" when trying to
transfer several gigs of QT movies from 1 Firewire drive
to the other (specifically a LaCie 320 GB drive from a
Western Digital 250 GB drive)
This has happened several times, can anybody recommend
a Disk Warrior cleanse on the drives or something else?
thanks

First thing to check: are both drives formatted macosextended? If not, some formats limit file size to 2gigs. Diskwarrior can't hurt. Also reformatting the target drive and zeroing it out so that any bad blocks are detected and fenced off is probably a good idea if you're having problems.

My iPod Classic 120GB is clicking and not turning on. It has been charged but does not hold charge. I am not able to restore factory settings. Error code and have tried troubleshooting options without success. Thoughts?

My iPod Classic 120GB makes a clicking noise when syncing with iTunes and will not sync. It will not turn on at this time and has been charged but does not hold the charge. After trying to sync, iTunes states that iPod must be restored. Have tried to do this but not successful, I receive an error code and have done the troubleshooting steps for the error and I am still not able to sync or use my iPod. HELP?

Hi mafiose15,
Thanks for visiting Apple Support Communities.
Restoring your iPod to factory settings is the best way to try and get it back to working order. You can use the instructions below to restore it:
How to restore iPod
Verify that you have an active Internet connection, because you may need to download new versions of the iTunes and iPod Software.
Download and install the latest version of iTunes if necessary.
Open iTunes. Connect your iPod to your computer using the USB or FireWire cable that came with your iPod.
After a few moments, your iPod will appear in the Source panel in iTunes.
Select your iPod in the Source panel. You will see information about your iPod appear in the Summary tab of the main iTunes window.
Click Restore.
If you are using a Mac, you will be asked to enter an administrator’s name and password.
A progress bar will appear on the computer screen, indicating that stage one of the restore process has begun. When this stage is done, iTunes will present one of two messages with instructions specific to the iPod model you are restoring.
Disconnect iPod and connect it to iPod Power Adapter (typically applies to older iPod models).
Leave iPod connected to computer to complete restore (typically applies newer iPod models).
During stage two of the restore process, the iPod displays an Apple logo as well as a progress bar at the bottom of the display. It is critical that the iPod remain connected to the computer or iPod power adapter during this stage.
Note: The progress bar may be difficult to see, because the backlight on the iPod display may be off.
After stage two of the restore process is complete, the iTunes Setup Assistant window will appear. It will ask you to name your iPod and choose your syncing preferences, as it did when you connected your iPod for the first time.
You can find the instructions in this article:
Restoring iPod to factory settings
http://support.apple.com/kb/ht1339
All the best,
Jeremy

HT201263 I purchased an 1gen 16GB Ipod from a seller. The ipod only shows the connect to itunes logo when connected to computer. The display shows without the word itunes. I got error codes 1603 and 1604 and have followed all the steps that were shown on

I purchased a 16gb ipod touch 1 gen and it wont restore or show the battery chaging icon. It shows the symbol of usb cable and what appears to be an itunes symbol without the itunes words being displayed. Upon trying to restore I have gotten error codes 1603 & 1604. I referred to the apple website for assistance and followed the steps to the letter with no results. So what else should I try or could I try because I have has no such luch thus far? I have held the home button and power button I tried to enter DFU mode but unsuccessful due to the screen boots with apple logo then immediately goes to the itunes screen and no further only when connected. Will not power on without usb connection have charged battery to see if it was the issue and no battery bar locator displays with or without being connected to PC.

So you did all this:
Error 1603: If you receive this error and the iOS device is not automatically placed into recovery mode, it may be necessary to do so manually. Refer to iPhone and iPod touch: Unable to restore for steps on placing iPhone into forced recovery mode. Also, remove the IPSW and attempt to restore again. If you do not want to remove the IPSW in the original user, try restoring in a new administrator user.
Error 1604: This error is often related to USB timing. Try changing USB ports, uninstalling and reinstalling USB ports, and other available USB troubleshooting steps (troubleshooting USB connections, device not recognized properly, computer won't recognize a FireWire or USB device). If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode,put it into Recovery Mode.
Restore and wait for error 1604.
When prompted, click OK.
Close and reopen iTunes while iPhone remains connected.
iPhone should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
http://support.apple.com/kb/TS3694#error1603
Did you try the last paragraph too?

" can't be read or written. (Error code -36)".

I am trying to drop files onto a newly installed GoFlex network storage system, but keep getting "The Finder can’t complete the operation because some data in “” can’t be read or written. (Error code -36)". I have seen some discussion, and tried as suggested, but no luck yet. Any suggestions?

I've been fighting "error code -36" with my Drobo connected to my Mac Pro (12 core) over Firewire 800. After hours of messing with it, I don't know for sure if I've solved the problem as I have only done cursory testing. Time will tell.
However, my solution was to move the Firewire cable to the 2nd Firewire port on the Mac Pro.
It seems to be working, as the copy operations are able to get past the errors I was having. Time will tell.

Error code -36

Hi there,
I'm encountering the following problem when attempting to trash or move files from a drive in an external FW800 enclosure:
The Finder cannot complete the operation because some data in "folder name" could not be read or written. (Error code -36).
Any ideas?
Many thanks in advance,
Ben
Dual 2 GHz PowerPC G5, 8GB DDR SDRAM Mac OS X (10.4.8) MacBookPro 2GHz Intel Core Duo, 1 GB 667 MHz DDR2 SDRAM

i have gotten this error a few times, i have a 250gb HD that is in a firewire enclosure, and i am copying the whole drive to a 500gb usb external, and it chokes part way through saying can't be read or written, -36 (is it so hard to say just read or write to narrow it down?). tried this on my powerbook and mac mini, tried switching 250gb hd's and firewire enclosures, firewire cables and power cables, so the only constant is the same usb drive. it's a new drive, guess it could be bad, but it keeps happening at different points in the transfer after reformatting the drive in between attempts, as well as popping up randomly during other large data transfers.
no other firewire devices attached, and the files that make it choke copy to the internal HD fine right afterwards. wish the error message told if it was a bad drive, bad drive cable, usb problem, firewire problem, or whatever else. seems to me like it's the usb external in this case, but i have gotten the same error on firewire to firewire transfers too. boo!

To what does G4 error code post16/4609 refer?

to what does G4 error code post16/4609 refer?
G4 MDD 1.42 PPC passes all hardware tests but gives post16/4609 error at start up.
What does it mean?
What is the resolution?

I don't get any unhappy beeps.
I get the chime. If I am not patient restarting I get high speed fan - I shut off be patience restart and get chime and search for drive then circle slash. hardware test gives me the master post 16 / 4609. - suggesting a bad drive according to other apple pundits. However, I have put two new 250GB WD drives in and still get a mass storage error. My G4 Mdd 1.42 supports drives 128GB+. I've replaced IDE cables and have master drive with out a jumper and have tried slave at CS and 3/4 slave setting all with the same result.
Target boot got me to the "firewire drive" showed me one unformatted 250GB drive and I used disc utility to partition it according the PPC settings. Still same error.
What gives?

Error code 1604

I keep getting Error code 1604 when trying to restore my Ipod Touch (keeps entering restore mode. never jailbroken)
Ive checked all my USB ports they are all 2.0 and all have up to date driver software. Does anyone have any other suggestions for this?
I have also tried updating Windows, and Itunes, shutting down my computer, creating a new user account, stopping the software from running and restarting it.
I am ready to throw the thing through the wall.
I can send it in for repairs but cannot call apple for support

This may help:
"Error 1604: This error is often related to USB timing. Try changing USB ports, uninstalling and reinstalling USB ports, and other available USB troubleshooting steps (troubleshooting USB connections, device not recognized properly, computer won't recognize a FireWire or USB device). If you are using a dock, bypass it and connect directly to the USB 30-pin dock-connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode, put it into Recovery Mode.
Restore and wait for error 1604.
When prompted, click OK.
Close and re-open iTunes while iPhone remains connected.
iPhone should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection."
Above from:
http://support.apple.com/kb/TS1275

Ipad stuck in recovery mode and won't restore--error code 1604

I tried to backup and update my ipad this evening and when doing so it now is stuck on the itunes and USB screen. When I connect the Ipad to the Itunes it says the Ipad is in recivery mode and to restore. I click ok and it tells me i can't restore the ipad and gives me an error code of 1604. I have no idea where to go from here or what happened. Any ideas?

Error 1604: This error is often related to USB timing. Try changing USB ports, uninstalling and reinstalling USB ports, and other available USB troubleshooting steps (troubleshooting USB connections, device not recognized properly, computer won't recognize a FireWire or USB device). If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
   1. Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode, put it into Recovery Mode.
   2. Restore and wait for error 1604.
   3. When prompted, click OK.
   4. Close and reopen iTunes while iPhone remains connected.
   5. iPhone should now be recognized in Recovery Mode again.
   6. Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
http://support.apple.com/kb/TS3694

My ipod touch has entered restore mode, but when I attempt to restore it I get the error code 1604.

My daughters ipod touch has entered restore mode, but when I attempt to carry out a restore I get an error code 1604.
Any easy solution to this problem?

Error 1604: This error is often related to USB timing. Try changing USB ports, uninstalling and reinstalling USB ports, and other available USB troubleshooting steps (troubleshooting USB connections, device not recognized properly, computer won't recognize a FireWire or USB device). If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode, put it into Recovery Mode.
Restore and wait for error 1604.
When prompted, click OK.
Close and reopen iTunes while iPhone remains connected.
iPhone should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
Above from:
http://support.apple.com/kb/TS3694

Upgrade failure, then restore failure, error code is 1604

IOS 5.01 upgrade to IOS 5.1 failure and can't restart, then restore failure and the error code is 1604

Error 1604: This error is often related to USB timing. Try changing USB ports, uninstalling and reinstalling USB ports, and other available USB troubleshooting steps (troubleshooting USB connections, device not recognized properly, computer won't recognize a FireWire or USB device). If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode, put it into Recovery Mode.
Restore and wait for error 1604.
When prompted, click OK.
Close and reopen iTunes while iPhone remains connected.
iPhone should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.

My 3GS went black today. How do I fix Error Code 1604?

My 3GS went black today. At first, I just thought the battery was dead. But when I went to charge it, it behaved differently. Eventually the Apple logo popped up, and then a message appeared that stated that I needed to activate the phone. The next screen said that I needed to hook it up to iTunes.
When I did that, it said that I needed to "restore" the device. Upon doing so, I eventually got a message that said there was a problem, and referenced Error Code 1604. I can see the online instructions of what to do, but none of that works.
So should I toss the phone in the garbage? Or take it 60 miles to the nearest Apple store? Or is there some brilliant person out there that can tell me how to fix this? :-)
Thanks!

Well, as the article says about 1604, if none of the steps work, it needs service;
Error 1604: This error is often related to USB timing. Try changing USB ports, uninstalling and reinstalling USB ports, and other available USB troubleshooting steps (troubleshooting USB connections, device not recognized properly, computer won't recognize a FireWire or USB device). If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode, put it into Recovery Mode.
Restore and wait for error 1604.
When prompted, click OK.
Close and reopen iTunes while iPhone remains connected.
iPhone should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
So you can either take it into an apple store, or call Apple and use one of their mail services.

Error code (-1302)/ firewire cable?

Similar Messages

Maybe you are looking for