Error code moving folder

An error cod moving a folder from one folder to another on the latest

Well, you'd have to delete the Movies folder before you could replace it, and deleting the Movies folder would also delete its contents, thereby making the replacement impossible. It's not really surprising that the Finder was confused.
Simple solution: rename the parent folder.

Similar Messages

G4 450 and protools, somehow ran out of memory to startup. Error code 10. Tried turning off extensions to boot but now just locks up as I tried a HD verify/repair and then moved the folder to the desktop screen. cant get it off now.froze.

Ok, I have a Mac g4, os9. ..450 Processor. I Think I upgraded ram, can't remember. Maybe a 512 card. Added an 80 gig internal HD for music storage. Computer was solely used for protools LE 5. I knew I was kinda close on my memory for running the program after recording things with plug ins etc. It was beginning to get slow at startup. Anyway it's been a couple years since I used it. I got it set up yesterday and it wouldn't launch and kept giving me error code 10. So I replaced the battery and tried again. the small finder icon in middle of screen would then pop up and alternate with a "?". Then it would change to a pict of a hard drive disk and then a me alternating "?". It would still give me the error code if I clicked on anything. So I then held down the shift key to turn off extensions as it had mentionEd to do a couple times. Still would give me the error code on my home page. If I tried to get into my hd which is on desktop it would give me the message, but somehow it did open one occasion and I went into it and scrolled to disk verify and repair. Did it. Said things were fine. I then saved the results in a file which was then offered along with location. I chose desktop. Probably really bad idea in hind sight.. It did it, but now no matter if I turn extensions off, the home screen pops up but then goes blank. The hard drive icon along with the new folder, and my protools icon immediately dissapear. And it freezes. at one point a message did pop up saying finder could not start up because there is not enough memory available. I'm not a computer guy. Ive tried finding the guy who helped me set this thing up 10 years ago but to no avail. If I can be guided to somehow uncover some of the unneeded memory usage I would then learn how to more efficiently use it. How the heck do I even start. I can't get to a screen which shows what's eating my computers space to even start getting rid of unneeded stuff. Please help if you can. I have so much to loose if I can't get it to work. Btw...I no longer have the os9 disk. I think it was tossed 10 years ago or more. May not even have my original pro tools disks anymore. Uggh.

Ouch, tough spot, but offhand I'd say some memory may have gone bad, or maybe just needs re-seating after all this time.
Not much you can do, but try this anyway...
PRAM reset, CMD+Option+p+r...
http://support.apple.com/kb/ht1379
In fact, do 3 in a row, takes a bit of time.

HT201413 I am receiving the error code (-50). The original itune songs etc were installed on a win 7 32 bit system and I have now moved to a win 7 64 bit system. Is this why I get the error code? I can access the itunes store to view my account. Any ideas

I am receiving the error code (-50) when trying to access the itunes store. The original itune songs etc were installed on a win 7 32 bit system and I have now moved to a win 7 64 bit system (same PC) and have copied the folder across. Has the switch from 32 to 64 bit caused the problem? Is this why I get the error code? I can, however, access the itunes store to view my account. Any ideas please?

Hello,
The TechNet Sandbox forum is designed for users to try out the new forums functionality. Please be respectful of others, and do not expect replies to questions asked here.
As it's off-topic here, I am moving the question to the
Where is the forum for... forum.
Karl
When you see answers and helpful posts, please click Vote As Helpful, Propose As Answer, and/or Mark As Answer.
My Blog: Unlock PowerShell
My Book: Windows PowerShell 2.0 Bible
My E-mail: -join ('6F6C646B61726C40686F746D61696C2E636F6D'-split'(?<=\G.{2})'|%{if($_){[char][int]"0x$_"}})

Yosemite is awful- unable to empty trash, volume options are haywire, error codes on file management, and files won't replace when moved. What are my options at this point?

Like the topic - "Yosemite is awful- unable to empty trash, volume options are haywire, error codes on file management, and files won't replace when moved. What are my options at this point?"
I installed this OS, and it looks nice, but it's terrible to use. I randomly have the volume controls get disabled, and sometimes the volume menu in the system tray does nothing when adjusted which I've never seen in an OS before. The trash won't empty. When I try to drag and drop newer files over existing ones, nothing happens. The old ones just stay there. I have to delete the old ones and then move the new ones. And when I go into the protected files to manage audio plugins (I make music), the first thing I hit are error codes galore, and password prompts that either don't popup when they should, or don't execute the command after I provide my password.
What can I do now that I installed the flames of **** onto my computer?

Back up all data before proceeding.
This procedure will unlock all your user files (not system files) and reset their ownership, permissions, and access controls to the default. If you've intentionally set special values for those attributes on any of your files, they will be reverted. In that case, either stop here, or be prepared to recreate the settings if necessary. Do so only after verifying that those settings didn't cause the problem. If none of this is meaningful to you, you don't need to worry about it, but you do need to follow the instructions below.
Step 1
If you have more than one user, and the one in question is not an administrator, then go to Step 2.
Triple-click anywhere in the following line on this page to select it:
sudo find ~ $TMPDIR.. -exec chflags -h nouchg,nouappnd,noschg,nosappnd {} + -exec chown -h $UID {} + -exec chmod +rw {} + -exec chmod -h -N {} + -type d -exec chmod -h +x {} + 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window by pressing command-V. I've tested these instructions only with the Safari web browser. If you use another browser, you may have to press the return key after pasting.
You'll be prompted for your login password, which won't be displayed when you type it. Type carefully and then press return. You may get a one-time warning to be careful. If you don’t have a login password, you’ll need to set one before you can run the command. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The command may take several minutes to run, depending on how many files you have. Wait for a new line ending in a dollar sign ($) to appear, then quit Terminal.
Step 2 (optional)
Take this step only if you have trouble with Step 1, if you prefer not to take it, or if it doesn't solve the problem.
Start up in Recovery mode. When the OS X Utilities screen appears, select
Utilities ▹ Terminal
from the menu bar. A Terminal window will open. In that window, type this:
resetp
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window will open. You’re not going to reset a password.
Select your startup volume ("Macintosh HD," unless you gave it a different name) if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Under Reset Home Directory Permissions and ACLs, click the Reset button.
Select
 ▹ Restart
from the menu bar.

Error code -8065 when moving Quicken 2007

Hey everyone
I recently bought Quicken 2007 (because I got tired of having to switch to Windows every time I wanted to use it) and am very happy with the purchase, contrary to many of the reviews I read on Apple.com
The only problem (inconvenience, rather) is that Quicken 2007 is in it's own folder (/Applications/Quicken 2007) . It contains the program package, the ReadMe, the license file, etc. However, I want to move just the program to /Applications. Every time I try, I get this error message:
+"Sorry, the operation could not be completed because an unexpected error occurred. (Error code -8065)"+
Does anyone know how to get around this? Or at least what the error code means? I searched Apple's online support and did not find info on the error code.
Thanks.

I had already looked at Google and did not find anything. I got Quicken moved by changing the folder name to Q2007 and then moving the app to the Applications folder. Thanks!
As to why I wanted to do this: I didn't want it in my dock, but I didn't want to have to open up a new finder window every time I wanted to use the app.
Thanks again.

Error code 36 when moving big files

getting error code 36 when moving big files from my mbp (10.6.8) to my external hard drive. have tried using the sudo command in terminal, but it doesnt work. what do i do?

sorry about that
I'm moving movie files around 800mb++ to HFS+ and NTFS formatted drives. no problems when using the NTFS drives with other computers but i cant really test the HFS drive on another computer since im the only one with a mac.
I've tried:
sudo cp /source/folder /destination/folder
but to no avail.

Cannot move folder because of error code -43

I am trying to move a Folder into my Applications/Utilities folder. When I move into any folder like Applications or Documents it moves fine. But when I try to move it into Utilities it asks me to authenticate and then I get this error:
The operation cannot be completed because one or more required items cannot be found. (Error code = -43).
Anyone know why this is happening?
Thanks,
Frank

It turns out what was going on was the folder I was moving is a shortcut. And where I was trying to move it already had a shortcut of the same name So Mac OS X gave me that informative error to tell me about the conflict.
Nice.

Error Code when trying to burn from a burn folder

Hey everyone,
I am trying to clean up some space on my powerbook G4 (not that I need to) but I like to keep things tidy. I was trying to burn some files onto a CD, it recognized the blank CD, displayed it in my finder as well as the burn icon, I had all the files set up, I hit burn, went to the speed selector, and then when I hit ok an error message popped up saying could not burn "Error Code 0x80020000). Any clue as to why that is? This is the first time I have had a problem burning files, both music and data have worked before.
Thanks for the help.

Hi, Joshua.
I presume you are using the internal optical drive that shipped from the factory with your PowerBook G4.
1. You wrote: "I am trying to clean up some space on my powerbook G4 (not that I need to) but I like to keep things tidy."Be careful not to "tidy up" anything outside of your Home folder or the Macintosh HD > Users > Shared folder. Your Home > Library folder is another folder that should not be altered unnecessarily.
"Tidying" System files can render your Mac inoperable unless you either:
• Have a deep understanding of Mac OS X and the files in question.
• Are instructed to remove such a file by someone with such understanding.
2. You wrote: "Error Code 0x80020000)"This is an "Internal Disc Recording" error.
You may have selected too high a speed for the optical media or the optical drive, have bad media, or be using optical media that your optical drive cannot see correctly. Some new, high-speed media use dyes that are problematic with older Mac optical drives. See Macintosh: Factors That Affect Writing to or Reading From Optical Media. If you've not used this brand of media before, try a brand and speed of media that has worked in the past.
Good luck!
Dr. Smoke
Author: Troubleshooting Mac® OS X

Hi guys, an empty folder is stuck in my trash & I get this message: "The Finder can't complete the operation because some data in the folder can't be read or written. (Error code -36). It won't shift no matter how I try to Secure Empty trash. Any ideas?

Hi guys, an empty folder is stuck in my trash & I get this message: "The Finder can’t complete the operation because some data in the folder can’t be read or written. (Error code -36). It won't shift no matter how I try to Secure Empty trash. Any ideas?

The Time Machines Backup is formated as Mac OS Extended (Case Sensitive, Journaled), my mac is formated as Mac OS Extended (Journaled).
The names on the file are all Uppercase
When I try to copy the Aperture file, it copies about 70% of the file (it's about 33GB in size), and halfway through I get this error.
I'm able to copy 99.99% of all of the images if I open the Aperture Folder using the "show package contents" under the backups using finder (Time Machine Backups>Backups.backupdb>CQ Macbook Air>2012-04-30-070933>HD.....>Pictures>Aperture Library). The only file I can't copy is that picture, which I'm totally ok with deleting, but Finder won't delete it for me. If nothing else works, I could copy the individual masters and re-create the folders, however I'd hate to do this as I would have to go through 10,000+ pics

I have one folder on an XSAN that one machine can not make changes to. Whenever I try to duplicate or copy a file in this folder I get 'The operation can't be completed because an unexpected error occurred (error code -50).'?

I have one folder on an XSAN that one machine can not make changes to. Whenever I try to duplicate or copy a file in this folder I get 'The operation can’t be completed because an unexpected error occurred (error code -50).'
The permissions are fine, and I have trashed the finder plist and reset the NVRAM.
Anyone have a answer?
Thanks

Tips I received so far (thanks to A-Mac via Twitter http://www.a-mac.nl and Remco Kalf http://www.remcokalf.nl/)
- make sure you have at least 10% of your harddisk in free space (I had only 5%).
- do a PRAM-reset (http://support.apple.com/kb/ht1379)
- perform a hardware test (http://support.apple.com/kb/HT1509)
- make a complete backup (with for example Carbone Clone Copier, see http://www.bombich.com/)
- after complete backup: use diskwarrior (boot from Diskwarrior DVD, first perform diagnostics, then perform "Rebuild" which rebuilds your file directory).
So far I only cleared up some space on my HD, and already the problem occurs less.
Still, I will go through the other tips too.
(will post progress)

Error Code -36 When Copying iTunes Music folder to an External Drive

_*"The finder cannot complete the operation because some data in "NAME.mp3" could not be read or written. (Error code -36)_"*
This is the error message I get when trying to copy my iTunes music folder to an external drive. I am following Apple's knowledge base article, so yes, I have consolidated my library, have closed iTunes and there is plenty of room on the external drive. For what it's worth, I am also getting this error when trying to do the same thing with my iPhoto library.
Would be grateful for some insight,
With oodles of appreciation in advance,
Joe

I was getting the same "-36" error while trying to backup to a Lacie firewire external drive.
I had a lot of people telling me to re-format, erase, reinstall, run utility programs ... yada, yada, yada.
First off, test to see if it is the connection type (firewire). I reconnected the offending external drive via USB, restarted the drive and ... BINGO! ... all transfers went perfectly.
Once i knew it was the firewire connection and not the drive itself i simply unplugged my iSight camera (the only other firewire device connected to my machine), reconnected my external drive via firewire and the problem is now corrected.
Firewire buses seem to be very finicky things ... i would suggest eliminating all firewire devices from the machine (except, of course, the external drive you're trying to transfer to) and see if the problem goes away.
Like i said, i simply unplugged my iSight camera and the transfer to my external drive went perfect and my transfer rates went from an average of 4MB/sec to over 19MB/sec.
P.S. BTW - prior to the error and after i corrected the error by unplugging the iSight camera, my internal and external drives all checked out 100% on Disk Utility, Disk Warrior and TechTool Pro.

"Error Code -50" when moving macbook pro?

Hello!
I'm having an issue that I can't exactly find anywhere else. Starting in August or so, my hard drive started having issues with error code -50, almost always when I moved the computer suddenly (setting it on a table, standing up with it too quickly, etc) or not-excessively-gently, although occasionally it happens without any movement. The computer still functions fundamentally "normally," but I can't use the internet (probably because the cache can't be accessed) and I can't open or save files. The issue corrects itself when I restart the computer, and probably repeats itself a few times a week.
It didn't start happening until I replaced my 320gb hard drive with a 500gb one and upgraded my 4gb RAM to 8gb at the same time. Thinking it was the hard drive, I took it back out and replaced my original hard drive, but the problem persisted. I did not try replacing the new RAM back with the original, but could bad RAM even contribute to the problem?
Thank you!

CLICKY CLICK----> Negative Value Error Codes
Disconnect all devices from the computer then do the following:
Boot up from your Snow Leopard Install DVD while holding down the "c" key.
Select the language you wish to use, and then choose "Disk Utility" from the menu bar.
Your HD should appear in a panel on the left hand side of the window which opens. Select it and then click on the "repair disk" button in the right hand section of the window.
Once this process has been completed restart your computer and repair permissions directly from Disk Utility.
If Disk Utility is unable to complete the repair, you will need to use a stronger 3rd party utility like DiskWarrior, Techtool PRO (not Deluxe) or Drive Genius.
Mac OS X (10.6.1)
Use Software Update or the OS 10.6.8 combo update to update your OS. Also, update everything SU has to offer for your computer. When done, repair permissions and restart your computer.

When I try to create a new folder I get an error code -50

I am copying files to an external Hard drive. I want to create a new folder on the external and I get an error code of -50 and no folder is created. How do I clear the error code so I can create floders?

The same thing happened to me: https://discussions.apple.com/message/25953748#25953748

I'm trying to transfer my pictures from my iPhoto library to my external hard drive. I dragged the iPhoto Library folder into the drive and after waiting a while it says Error Code -36. I need to free up space asap, what should i do?

I'm trying to transfer my pictures from my iPhoto library to my external hard drive. I dragged the iPhoto Library folder into the drive and after waiting a while it says "Error Code -36 The finder cannot complete the operation because some data in 'iPhoto Library' could not be read or written". I need to free up space asap, what should i do??

Yes, the Old Master file has a folder for each year where I find all photos from that specific year. I am attaching a screen shot of the file.
In the meantime i have managed to download all photos (it did not download any video files though in mpg, avi, 3gp, m4v,mp4 and mov format) to a new iphoto library. Unfortunately the photos are quite mixed and often doubled up. I ma considering to purchase iphoto library which checks all duplicates in iphoto. this will save me a lot of time. What do you think?

Cannot access a shared folder Error code: 0x80070035

Hello Experts,
I have been working on this issue for like three days without a solution. I am truly desperate.
My company just purchased a new Cloud Server that we will use as our development environment for a software project. In order for all the developers (which are all over the US) to access the development environment, we need to have a few shared folders on
that new server.
As soon as we got the server I did the following:
1) Installed Active Directory
2) Created a directory and made it shared - yes IT IS shared.
3) I created a few new users on the new active directory domain
THE PROBLEM:
I can't access the shared directory.
Other developers have been successful in connecting to the shared folder (so the share is working) - all except me.
when I open explorer and type \\IPADDRESS\SHAREDFOLDER instead I get this error (I am not even asked for credentials)
Network Error
Windows cannot access \\IPADDRESS\SHAREDFOLDER
Error code: 0x80070035
The network path was not found.
Things I have already tried:
a) Enable NetBIOS over TCP/IP - on all adapters - still did not help
b) Disable IPv6 - I am not sure how to check if it truly disabled
c) Turned off all firewalls - did not help
d) Mapping a Drive using different credentials - I just get asked for credentials over and over
e) Ping - yes I can see the server
f) My credentials are correct because I can Remote Desktop with the credentials with no problem ( I am administrator)
My Machine:
Brand New Asus G Series
Windows 7 Home Edition
Any ideas?
Sorcerdon

In my case it was that the OU that my system was in did not have firewall rules for network file and printer sharing enabled. I enabled all of the rules for Domain policy and that fixed it.
I noticed a lot of comments about turning off the firewall not working. I can't be 100% sure, but in my experience with Server 2008 and Windows 7, if you want to configure a service that uses the network the base filter engine and the firewall HAVE to be
turned on while you configure. You can turn the firewall off after configuration, but they have to be active during configuration.
Good luck!

Error code moving folder

Similar Messages

Maybe you are looking for