Error Communicating with DCR Server

Hello,
While trying to edit device credentials, I got this error from DCR:
Error in communicating with DCR Server.
DCR Server may be down. Please start the DCR Server and then refresh the page.
But when I checked the DCRServer process status from Process Status Report and the Process List, it's Running normally.
What could be the problem? The CiscoWorks server runs 3.0.1 (December 2007 Update). Attached are pdshow command output, dcr and DCRServer logs

Hi Joel,
I have the same problem with LMS 3.1,
Products Installed
Re: Error Communicating with DCR Server
Name
Version
License Status
Size
CiscoWorks Common Services
3.2.0
Licensed
Not applicable
Campus Manager
5.1.4
Evaluation
100
CiscoView
6.1.8
Licensed
Not applicable
CiscoWorks Assistant
1.1.0
Licensed
Not applicable
Device Fault Manager
3.1.3
Evaluation
100
Internetwork Performance Monitor
4.1.0
Evaluation
100
Integration Utility
1.8.0
Licensed
Not applicable
LMS Portal
1.1.0
Licensed
Not applicable
Resource Manager Essentials
4.2.0
Evaluation
100
Health and Utilization Monitor
1.1.0
Evaluation
100
When I try to edit Device Credential, this error appears.
Error in communicating with DCR Server.
DCR Server may be down. Please start the DCR Server and then refresh the page.
DCRServer is stopped and started but the problem still appears.
Thanks.

Similar Messages

Error in communicating with DCR server (Operations Manager 8.5)

Hi,
I just installed Operations Manager 8.5 on a new server. And, although I'm able to login to the OM, I'm unable to add any devices to the DCR. When attempting to add the device the following error is returned:
"Error in communicating with DCR Server
DCR Server may be down. Please start DCR server and then refresh the page. "
The same error is returned when an attempt is made toaccess the screen to change the mode (standalone/master/slave.) However, according to pdshow output DCRServer is up and running:
Process= DCRServer
State = Running normally
Pid    = 9220
RC     = 0
Signo = 0
Start = 7/29/2011 2:46:33 PM
Stop   = Not applicable
Core   = Not applicable
Info   = DCRServer is up and running
I've browsed the site and tried all suggestions for LMS since I didn't see any for OM. No success.
Any/all suggestions are much appreciated.
Kind regards,
Bart

It appears the answer is rather simple. According to a trusted source who works for a Cisco training partner, one must wait before even attempting a login into OM.
Apparently, it takes about 25 to 30 minutes for all the services to start. Any attempt to login to the OM may corrupt the database. This is based on CiscoWorks. When command "net stop crmdmgtd" is issued it takes about 5 minutes to stop the service and a confirmaiton that the service was stopped is displayed. However, when starting the service with "net start crmdmgtd" there is no confirmation that it started successfully. One may look into ":\ program Files\CSCOpx\objects\dmgt\ready" directory for a _lock file." As long as the lock file is present one shouldn't use the browser to login. However, I was advised the best approach is to restart the service and give it 30 minutes.
It worked for me
Kind regards,
Bart.

Error in Communicating with DCR Server LMS 4.0

I´m receiving this error when I try do add a device in isolated form or by discovery:
Error in communicating with DCR Server.
DCR Server may be down. Please start the DCR Server and then refresh the page.
I am using windows 2008 standard server RC1 SP1, and CiscoWorks LMS 4.0.
I had applied all of patches includes.
The DCRserver is running. ( I did restart it)

You're using Windows 2008 RC1 (a release candidate version)? LMS is only supported on the final shipping version of Windows 2008, and not yet on R2.
If you're running on the final version of 2008 server, post the output of the pdshow command as well as the dcr.log, DCRServer.log, NMSROOT/MDC/tomcat/logs/stdout.log and stderr.log.

Error in communicating with DCR Server. in LMS 3.1

I am receiving this error when I try to ad device: Error in communicating with DCR Server.
DCR Server may be down. Please start the DCR Server and then refresh the page.
The DCRserver is running. ( I did restart it)
I am using Windows version of LMS 3.1
CiscoWorks Common Services 3.2.0 Licensed Not applicable
Campus Manager 5.1.4 Purchased 300
CiscoView 6.1.8 Licensed Not applicable
CiscoWorks Assistant 1.1.0 Licensed Not applicable
Device Fault Manager 3.1.3 Purchased 300
Internetwork Performance Monitor 4.1.0 Purchased 300
Integration Utility 1.8.0 Licensed Not applicable
LMS Portal 1.1.0 Licensed Not applicable
Resource Manager Essentials 4.2.0 Purchased 300
Health and Utilization Monitor 1.1.0 Evaluation(Expired) 100

Hi,
This issue most likely is related to a communication problem with the database or a corruption as we can see from the logs :
2010/11/21 19:44:41 main ani ERROR POStore: Failed resolving object because: java.lang.NullPointerException
2010/11/21 19:44:41 main ani ERROR AniMain: java.lang.NullPointerException
ANI Server failed to load from the database.
Please stop and restart the system. You may need to re-initialize the database.
If this does not work, please contact technical support.
The next step is to re-initialize the Campus Manager database. This procedure will delete all the records and maps that you have in Campus Manager, you would need to run a new Campus Data Collection and User Tracking Acquisition to have clean and fresh database information.
If that ok with you, you can try the below steps to re-initialize the Campus database. By doing this, it will not effect any other database of LMS will clean Campus Manager database.
+) Stop the daemon manager:
net stop crmdmgtd
+) cd CSCOpx\bin\
+) Type the following command (case sensitive):
perl dbRestoreOrig.pl dsn=ani dmprefix=ANI
+) Start the daemon manager:
net start crmdmgtd
Now, wait another 15 minutes and wait for dmgtd.lock file to release from location CSCOpx\objects\dmgtd\ready.
Now check the status of ANIServer with command :- pdshow ANIServer ( case sensitive)
it should have the status Busy with Flag set.
Thanks,
Gaganjeet

There was an error communicating with the server. Click on the back button in you browser and try resubmitting the form.

I've had several users complain of receiving this message after they have filled out and submitted a form.
There was an error communicating with the server. Click on the back button in you browser and try resubmitting the form.
However the data is being saved in forms central. I can't duplicate the issue on my end but it seem to be happing frequently with other users.

Do you mind emailing the URL of your fillable form to me ([email protected]).
I would like to investigate as to what the issue might be with Internet Explorer.
Sorry for the inconveniences.
Gen

An error has occurred. There was an error communicating with the server. Please try again later.

I have a simple form which allows users to submit receipts as attachments. I have some required identifying information (name, etc.) and then three optional slots for attachments, along with optional text boxes for descriptions. The form tests fine with attachments on my computer and on a couple other computers we tested with.
However, I am getting complaints from several users that they see the following message when they hit "Submit": "An error has occurred. There was an error communicating with the server. Please try again later." Any ideas why this might be or how I can fix it?

Do you mind emailing the URL of your fillable form to me ([email protected]).
I would like to investigate as to what the issue might be with Internet Explorer.
Sorry for the inconveniences.
Gen

Error communicating with AdobeID server - DAY 3

So, I'm trying to activate the Digital Editions of Adobe on my MacBook, but I keep getting this darned message:Error communicating with AdobeID server. Please try again later.
What in the world is happening? I've been trying to get this to work for nearly 3 days. My classes will begin soon, and I'm REQUIRED to have this Adobe Digital Editions in order to download my books. WTH?! Can someone please help me get around this problem please?
Thank,
Monique

I'm getting the same problem. I'm in the UK
My error message is: E_AUTH_DATABASE_CONSISTENCY http://adeactivate.adobe.com/adept/SignInDirect AdobeID
(I have removed my ID)

When I try to access GameCenter on my Mac it says "The requested operation could not be completed due to an error communicating with the server." How can I fix this?

When I try to access GameCenter on my Mac it says "The requested operation could not be completed due to an error communicating with the server." How can I fix this?

This usually caused by a customised hosts file.
These need to be the only entries in your /etc/hosts file:-
# Host Database
# localhost is used to configure the loopback interface
# when the system is booting. Do not change this entry.
127.0.0.1       localhost
255.255.255.255 broadcasthost
::1             localhost
fe80::1%lo0     localhost
Remove anything below these entries, then try and reconnect with GC. Once GC starts properly you can put the extra entries back in your hosts file, GC should start normally afterwards.
https://discussions.apple.com/message/19276629#19276629
Jerry

"Error communicating with AdobeID server"

Every time I try to authorize my ADE, I keep getting this error message:
"Error communicating with AdobeID server. Please try again later.
E_ADEPT_IO AddSignInDirect Error%20#2032"
I've tried to authorize it more times than I can count over the past few weeks - anyone know what I can do to fix it?
It used to work just fine, but then I started getting error messages on any books I tried to download and nothing I did would fix it, so I tried uninstalling then reinstalling and it won't let me authorize it now (I tried authorizing with a different ID too, to see if that was the problem but it wouldn't work).

Hi,
As per the error message that you are getting E_AUTH_BAD_DEVICE_KEYplease follow the steps as given below.
1) Open Adobe Digital Editions.
2) Press Ctrl+Shift+D key of your Keyboard and deauthorize Digital Editions
3) Move your e-books to some different Location.
4) uninstall Adobe Digital Editions from your computer.
     Click start>>Control Panel>>Add or remove Program
     Select Adobe Digital Editions from the list and Delete.
5) Also delete following files.
    Click Start>>Run
    Type "regedit" without quotes in the box and hit enter.
    Locate the following key "HKEY_CURRENT_USER>Software>Adobe>Digital Editions"
    delete the full folder (Right click on it and click delete).
     Also locate HKEY_CURRENT_USER>Software>Adobe>Adept
     Delete the full folder.
6) Now download and install Adobe Digital Editions from the link given below.
     http://www.adobe.com/products/digitaleditions/
7) When asked to authorize computer then please enter same Adobe ID and password and authorize the same.
I hope this will help you!!!
Regards
Rizwan

Error communicating with AdobeID server. E_AUTH_BAD_DEVICE_KEY

Running Digital editions 1.5 on an Ibook G4 with OSX version 10.4.11
Installed digital editions, downloaded my book. Started reading, then needed to reboot machine. once I rebooted, I tried to open ADE once more, but I again had to "reactivate" the machine... once I try to reactive it I keep n getting stuck (whether I chose to authorize or not authorize the machine is irrelevant) on the same error...
Activate Digital Editions
Error communicating with AdobeID server. Please try again later.
E_AUTH_BAD_DEVICE_KEY
what's going on? When can I read my book? Is your server down? does this happen often? Is this related to the version of ADE?

Carolina,
regarding the E_AUTH_BAD_DEVICE_KEY error...
We can't tell you -exactly- what this is, but we can give you some general direction.
On the Mac, Digital Editions 1.5 stores an encryption key (to make sure our client to server calls are secure) in your OS X Keychain.
If there is a problem creating this key then E_AUTH_BAD_DEVICE_KEY is the error you'd see.
The key information is stored as an application password in your keychain. Likely causes of failure include denying access to Digital Editions, or locking your user keychain, and not entering their password when prompted.
If you're denying access explicitly to Digital Editions, well don't do that (ha. )
Now, you may not be doing this intentionally. The access permissions on OS X are complicated, so this could be a side effect of some other permission work. You can explicitly grant Digital Editions access to the the keychain item:
Open Keychain Access (Applications/Utilities)
Select Passwords from Category
Select Digital Editions from password list
Click info button (or press Cmd+i)
(Dialog labeled Digital Editions should appear)
Select Access Control tab
Click + button
Navigate to our install directory and select ADE 1x5
Click Save
Close Dialog
Launch Digital Editions.
Anyway, hopefully this helps you narrow the issue down.
Regards,
Bentley Wolfe
Senior Support Engineer, Flash/Flash Player/Digital Editions
Adobe

That sends me this error: There was an error communicating with the server, try later when I want to create a new Keynote presentation?

good day !!! I am trying to create a new presentation in keynote,
when selected sends me the following message: An error occurred while communicating with the server, try again later. I tried for
several days to make the presentation but I keep sending the same message. I'm trying to make it from the keynote
beta (from iCloud)

This is the Mac discussion, post your issue in the iWork iCloud discussion where folks who use iCloud can help you.
iWork iCloud Discussion

CDAU12035 Error communicating with Enterprise Server

I am getting this error when trying to get the Enterprise Data to display on the CAD. Anyone seen this before.

Hi everyone,
We just received this error message.... CDAUI2035 Error Communicating with the Enterprise service. We are using UCCX 9 and premium NO HA on this server.... What can we do to fix this issue?

Activate change lists error - Communication with JMS server failed

Hi,
I have this error message prompted when I try to activate my design object in Integration Builder :-
<i>Communication with JMS server failed Repeat the last action. If the problem continues to occur after multiple attempts, contact your system administrator to check the availability of the JMS provider service.</i>
Anyone knows where should I fix the errors ? Many Thanks in Advance.
regards

Hi,
I think you should check the JMS Provider service in the Visual Administrator.
Have a look at those help pages:
<a href="http://help.sap.com/saphelp_nw04/helpdata/en/90/57849e5e3e45d784afc4e3bfa8136f/frameset.htm">JMS Administration</a>
<a href="http://help.sap.com/saphelp_nw04/helpdata/en/a9/ad3d9ef22e4b2ea9752de8d98db5a4/frameset.htm">JMS Provider Service</a>
Best regards,
Manuel

Error communicating with FTP server....

Hey everyone,
I registered a domain through GoDaddy.com two days ago, but only finally settled down with a host yesterday (Monday). My free host is byethost.com. After signing up for a host, adding my domain, and changing the domain's DNS's, I am aware that there is a period of time for "propagation." Using iWeb 09, I have been trying to upload my site via ftp (obviously), using the settings and information Byethost has given me. However, iWeb always comes back saying that there was an error in communication. Do I need to wait until the DNS propagation is completely done (as it is not at the time of this post)? Or, is there something I am missing? Thank you for your help and I'll be glad to send along any info necessary!
BTW: The "Test Connection" button works perfectly and says I can upload. hmmm...nope
Jordan

You should be able to upload your files as this has nothing to do with the domain name.
The iWeb FTP is not exactly the world's best!
Try downloading the freeware Cyberduck if you don't have an FTP application.
http://www.iwebformusicians.com/SearchEngines/Upload.html

I Have this error when i try to access Resource central in Encore CS4:We're sorry, but there was an error communicating with the server. Please try again and if the problem persists, contact Adobe Technical Support. (200) INVALID_QUERY : [object XMLList]

Please anyone whit same problem tell me something i need a solution...
Best regards,
Luís Vaz de Miranda.

I do not believe the Resource Central exists anymore. You can download the CS6 full library.
http://helpx.adobe.com/encore/using/download-library-content.html

Error Communicating with DCR Server

Similar Messages

Maybe you are looking for