Error compiling movie. Disk Full.

Hello, i keep getting an error message from Adobe Encoder CS5.
- Source File: L:\Toshi_2\Front_Angle_01.mpeg
- Output File: J:\Front_Angle_01_1.MXF
- Preset Used: AVC-Intra Class50 1080
- Video: 1440x1080, 29.97 [fps], Progressive
- Audio: 48000 Hz, Stereo, 16 bit
- Bitrate:
- Encoding Time: 00:23:24
9/25/2011 6:53:13 PM : Encoding Failed
Error compiling movie.
Disk Full.
I'm trying to trancode a 11-minute HDV footage to P2 format for editing. The destination Hard drive is a NTFS file system 500gb esata drive with 300gb free. I have successfully done this many times before but this time it gives me the error message. It happens like 5 times now. I have tried to clean the Cache and set the destination to my PC's internal drive, but the result is the same.
Does anyone has the same problem and how to resolve this?

Make sure you're running the latest updates for AME - it could have been addressed in one of the patches. Beyond that, that Disk Full error can be misleading - there are times that's displayed when it's just an encoding failure. It could actually be something as misleading as an error decoding some part of the mpeg - I'd try loading the .mpeg into PPro and try playing through the entire file - check to see whether or not you get any errors down on the status bar (bottom right, a stop sign will show up) - if there's an error generating the mpeg index file or errors in the stream, that's where they'll pop up.

Similar Messages

Media encoder error compiling movie disk full

I am trying to encode a movie, and the encode is estimated to take 2 hours. I am using my new mac pro, osx 10.9.3.
This comes up after I get the message "DIsk not ejected properly" from the system.
The disks still appear in the finder, and the files in the hard drive are still linked from within premiere.
The disks are not full. There are 1.1 terabytes still available.
The computer is not going to sleep, although the hard drives might be going to sleep.
System Preferences > Energy Saver > Put hard disks to sleep when possible has been UNCHECKED.

Some 10.9.3 links
-Mac 10.9.3 workaround https://forums.adobe.com/thread/1489922
-more Mac 10.9.3 https://forums.adobe.com/thread/1491469
-Enable Mac Root User https://forums.adobe.com/thread/1156604
-more Root User http://forums.adobe.com/thread/879931
-and more root user http://forums.adobe.com/thread/940869?tstart=0

CS6 - "error compiling movie - Disk Full"

This is the message I am getting from both Premiere and Media Encoder cs6 when I try to export my Premiere project. It is 1080p 59.94fps. This disk I am exporting to is FAR from full. I am running Mac OS X 10.7.4 - not sure how else I can export with these settings aside from "match sequence settings". Has anyone else had this problem?

Just to add a data point, having same error editting 1080P60 footage:
New CS6 Premiere Set-up
New Fresh win7 64bit install
P9x79 Mobo - 64MB RAM
3 Drives:
OS - Raid 0 (2 - corsair force SSDs - 350 GB total) - 900/500MB Reads/writes
Clips - Raid 10 (14 - 2 GB WD blacks - Areca controller#1 - 12.7 TB total) - 1000/1000 MB Read/writes
scratch/preview - Raid 0 (9 - corsair force SSDs - Areca controller#2 - 1.6 TB) - 3000/3000 MB Read/writes (yes - I know ;->)
All drives NTFS and internal (so that is not the issue). Have NOT installed quicktime yet.
Can't export back to orginal settings - but can for any other format.
So it is something else beside a FAT32 and/or free space issue.

Export Error. Error compiling movie. Disk Full.

I have the following error since CS6 when exporting some videos: Export Error. Error compiling movie. Disk Full.
All my drives have plenty of space, NTFS 7200rpm, everything was fine with CS5.5. Same problem with Encoder or Premiere Pro.
Much of the stuff I export is going fine but I have this error with some sequences and formats.
It always crash to this error when exporting sequences with "Match Sequence Settings".
For one of my projects, when exporting to wmv, out of 6 sequences one always crash to Export Error. Error compiling movie. Disk Full.
If I encode those sequences to mpeg2, everything is fine.
I installed the new update this morning but it doesn't help.

Hi, since my last post there has been no activity on this thread, so...
Has anyone found a workaround? I find it incredibly inconvenient and unforgivable that I get this error when trying to export a movie in PPCS6 using "Match Sequence Settings". Some facts:
1. I always get this error when trying to export from PPCS6 using match sequence settings. It happens with all movies. Starting a new sequence doesn't change it
2. I never get this error if I use another encoding option
3. My disk is not full
4. It happens whether I use software engine or GPU acceleration (and also if I delete the previews)
5. It happens on both the PC and MAC versions of PPCS6. With sequences created natively on each machine and imported one to the other.
6. If I import the sequence into CS5, then hey presto, it works without error. At the moment that is my workaround, but it is not at all acceptable that I have to do this.
7. The sequences were all created in CS6. None of them were imported from another version
8. My source video is 1080p AVCHD footage
Any further thoughts on how to deal with this really frustrating and crippling new bug in CS6 would be incredibly welcome.

Error compiling movie - unknown error - encoding failed

I am running a 2.40 GHz Quad Core with 8GB RAM
I have a deadline on a video project in Premiere Pro CS4 with 4 video timelines and 8 audio timelines with many transitions and key frames with hours on two sequences of work completed and ready to export to an AVI file and burn a DVD. The 30 minute sequence with only 3 timelines converted to AVI file okay. The larger sequence with more timelines, keyframes, etc. will not export through Adobe Media Encoder for a Microsoft AVI file or an Uncompressed AVI file - getting the above error message each time. Getting same errors when exporting a dynamic link to Encore to burn a DVD.
The sequence acted funny when I loaded the fourth video timeline so I deleted it and waiting untill the completion of the sequence to add any of that fourth timeline to that sequence and I did not even try to load the fourth timeline that I wanted to add...
Here are the error messages I am getting:
- Source File: C:\Users\dbonnett\AppData\Local\Temp\Katie Hill Wedding V03_4.prproj
- Output File: C:\Users\dbonnett\Videos\2009-04-11, katie hill wedding\katie hill finished videos\Hill Ceremony Final.avi
- Preset Used: NTSC DV
- Video: 720x480, 29.97 [fps], Lower, Quality 100
- Audio: 48000 Hz, Stereo, 16 bit
- Bitrate:
- Encoding Time: 00:19:56
6/16/2009 7:29:23 PM : Encoding Failed
Error compiling movie.
Unknown error.
- Source File: C:\Users\dbonnett\AppData\Local\Temp\Katie Hill Wedding V03_5.prproj
- Output File: C:\Users\dbonnett\Videos\2009-04-11, katie hill wedding\katie hill finished videos\Hill Ceremony Final.avi
- Preset Used: NTSC DV
- Video: 720x480, 29.97 [fps], Lower, Quality 100
- Audio: 48000 Hz, Stereo, 16 bit
- Bitrate:
- Encoding Time: 00:16:23
6/16/2009 8:11:08 PM : Encoding Failed
Error compiling movie.
Unknown error.
I have been going back & forth with Adobe Support with troubleshooting advice. I am running a 2.40 GHz Quad Core, 8GB RAM - had to upgrade to Windows Vista 64-bit for computer to recognize more than 2GB RAM, had to purchase Premiere Production Premium CS4 because Adobe no longer supported Premiere Pro 2.0 & Adobe does not support Windows XP-64 bit (so Windows Vista was pushed down my throat...) I have followed the Adobe instructions to Optimize Windows Vista for Adobe Premiere Pro CS4, I have uninstalled and re-installed the full program more than once. I have defragmented my computer, I have performed the disk cleanup and deleted all temporary files, etc. to make sure my computer is running optimally.
I have read the other Adobe threads that talk about CS3 & earlier similar error messages, but have found nothing with this particular message. I have deleted the fourth timeline off of the video and tried to see if that would make it work, but it did not.
Does ANYBODY have any suggestions on how I can further trouble shoot to get this project out or know of a way that I can export this project to another program to get an AVI file and a DVD burned with custom menus...

I am using a 1TB Hard drive with 300 GB free space. Yes, I always have to delete projects off to make room for new projects. I have 3 750GB hard drives in my computer in addition to the main C drive that I am using. Once a project is completed and a client is satisfied, I move the final AVI file off to one of the auxillary drives and delete the entire project from the C drive. Then I defragment, delete temp files, disk cleanup, you name it to get the drive ready to use for the next project. I have followed the Adobe protocol for all of this as well as my computer vendor. I got rid of 95 GB of temp stuff several days ago with the disk cleanup and another 45 GB after deleting another project off my computer... so looks like I am doing these things..please advise if you know of anything else.
In the meantime, I am going to try to export to the MPEG2 -DVD export to see if this will work. I did get an uncompressed file of 31 GB created which errored out at 24:24 minutes into the project and the AVI will not play so it is worthless so I am going to delete it. I went to the timeline at 24.24 minutes and there is nothing unusual about that portion of the clip. This is the largest and most tedious timelines of the project because it is stacked 3 video timelines high with just a a few pieces of the 4th timeline in the project. 24:24 on the timeline is just another keyframe of moving the keyframes up and down to show which video camera version I want visible in that portion of the video - fading in and out of the project with the key frames...
I will let you know if I can get an MPEG2 file. Will this be a good enough quality to put on a DVD. This is a standard NTSC 4:3 format video...

Adobe Media Encoder (Error compiling movie) Unknown error when writing to Isilon OneFS 6.5.5.18

Adobe Media Encoder (Error compiling movie) Unknown error when writing to Isilon OneFS 6.5.5.18 while using Adobe Premiere Pro.
Process:         Adobe Premiere Pro CC 2014
Path: /Applications/Adobe Premiere Pro CC 2014/Adobe Premiere Pro CC 2014.app/Contents/MacOS/Adobe Premiere Pro CC 2014
Identifier: com.adobe.AdobePremierePro
Version:         8.1.0 (8.1.0)
Code Type: X86-64 (Native)
Parent Process: launchd [2538]
Responsible:     Adobe Premiere Pro CC 2014
Date/Time: 2015-01-06 14:04:23.500 -0700
OS Version:      Mac OS X 10.9.2 (13C64)
Report Version: 11
Crashed Thread: 55 Dispatch queue: com.apple.root.default-priority
Exception Type: EXC_BAD_ACCESS (SIGSEGV)
Exception Codes: KERN_INVALID_ADDRESS at 0x0000000000000000
Customer created test export with 777 permissions and set mount parameters to the following:
mount_nfs -o vers=3,tcp,rdirplus,intr,nolocks,async,rsize=32768,wsize=32768
-- Original mount options:
     General mount flags: 0x40 async
     NFS parameters: vers=3,tcp,nolocks,rsize=32768,wsize=32768,rdirplus
-- Current mount parameters:
     General mount flags: 0x4000058 async,nodev,nosuid multilabel
     NFS parameters: vers=3,tcp,port=2049,nomntudp,hard,nointr,noresvport,negnamecache,callumnt,nolocks,quota, rsize=32768,wsize=32768,readahead=16,dsize=32768,rdirplus,nodumbtimr,timeo=10,maxgroups=16 ,acregmin=5,acregmax=60,acdirmin=5,acdirmax=60,nomutejukebox,nonfc,sec=sys
The pcap shows once the movie is created a lockup call is responded from Isilon with Error: NFS3ERR_NOENT
478         V3 CREATE Call (Reply In 479), DH: 0xea5f731c/QBRSN-0-0-1.mov Mode: UNCHECKED
479         V3 CREATE Reply (Call In 478)
484         V3 LOOKUP Call (Reply In 485), DH: 0xea5f731c/._QBRSN-0-0-1.mov
485        V3 LOOKUP Reply (Call In 484) Error: NFS3ERR_NOENT
V3 LOOKUP Reply (Call In ....) Error: NFS3ERR_NOENT -   This is by design of OneFS, we coalesce files and then flush them out to disk which is why the commit time is accurate but the file is not immediately available. however when an async option is used within the mount options this should be avoided if writing asynchronously to the cluster. Has anyone else seen this behavior lately? (current workaround is to store locally and transfer to the cluster via Finder)

That error can happen for many reasons...one of the reasons that I occassionaly get it is because I try exporting a movie to an external drive that has been formated in the old FAT32 instead of the NTSF standard. FAT32 only allows for file sizes up to 2 gigs. And as soon as it reaches that...I would get that error. I don't know if that is why you are getting that error...but it would be easy to check. 1) are you generating a file that is over 2 gigs? 2) is your drive that you are exporting to FAT 32 (just right click the drive in My Computer and select "properties" then just look for what it says next to "file system".

Error compiling movie. I/O Error.

Hello.
Im not sure if i should have posted in the hardware section.
I have done some reaserch on this problem but haven't really got the solution.
It doesnt matter what format i export it always gives me this error. With h264 and some else, its a bit different too.
- Source File: C:\Users\SEMPER~1\AppData\Local\Temp\Untitled_1.prproj
- Output File: C:\Users\Kristjan\Desktop\Sequence 01.mp4
- Preset Used: YouTube KW
- Video: NTSC, 480x360, 30 [fps], Progressive
- Audio: AAC, 64 [kbps], 48 kHz, Stereo
- Bitrate: VBR, 1 Pass, Target 1,55, Max 2,29 [Mbps]
- Encoding Time: 00:00:00
3.12.2009 0:53:45 : Encoding Failed
Cannot open "C:\Users\Kristjan\Desktop\Sequence 01.mp4" file for writing. Please check the output filename and file permissions (if it already exists) and then try again.
- Source File: C:\Users\SEMPER~1\AppData\Local\Temp\Untitled_2.prproj
- Output File: C:\Users\Kristjan\Desktop\Sequence 01.avi
- Preset Used: NTSC DV
- Video: 720x480, 29.97 [fps], Lower, Quality 100
- Audio: 48000 Hz, Stereo, 16 bit
- Bitrate:
- Encoding Time: 00:00:00
3.12.2009 0:54:47 : Encoding Failed
Error compiling movie.
I/O Error.
- Source File: C:\Users\SEMPER~1\AppData\Local\Temp\Untitled_3.prproj
- Output File: C:\Users\Kristjan\Desktop\Sequence 01.avi
- Preset Used: NTSC DV
- Video: 720x480, 29.97 [fps], Lower, Quality 100
- Audio: 48000 Hz, Stereo, 16 bit
- Bitrate:
- Encoding Time: 00:00:00
3.12.2009 0:58:04 : Encoding Failed
Error compiling movie.
I/O Error.
- Source File: C:\Users\SEMPER~1\AppData\Local\Temp\Untitled_4.prproj
- Output File: C:\Users\Kristjan\Desktop\Sequence 01.avi
- Preset Used: Custom
- Video: 720x480, 25 [fps], Progressive, Quality 100
- Audio: 48000 Hz, Stereo, 16 bit
- Bitrate:
- Encoding Time: 00:00:00
3.12.2009 1:08:37 : Encoding Failed
Error compiling movie.
I/O Error.
- Source File: C:\Users\SEMPER~1\AppData\Local\Temp\Chemistry, Copper_6.prproj
- Output File: C:\Users\Kristjan\Desktop\Youtube.avi
- Preset Used: Custom
- Video: 720x480, 25 [fps], Progressive, Quality 100
- Audio: 48000 Hz, Stereo, 16 bit
- Bitrate:
- Encoding Time: 00:00:01
3.12.2009 1:28:42 : Encoding Failed
Error compiling movie.
There are alot of errors about my hard drive in the event viewer aswell. I have 2 hard drives.
The device, \Device\Harddisk1\DR1, has a bad block.
The driver detected a controller error on \Device\Harddisk2\DR2.
even my cd rom has a bad block, The device, \Device\CdRom0, has a bad block.
I defrag my drives regulary.
My PC ,I use the "system information" option that win 7 has :
OS Name Microsoft Windows 7 Ultimate
Version 6.1.7600 Build 7600
Other OS Description Not Available
OS Manufacturer Microsoft Corporation
System Name SEMPERFI-PC
System Manufacturer System manufacturer
System Model System Product Name
System Type x64-based PC
Processor Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz, 2997 Mhz, 2 Core(s), 2 Logical Processor(s)
BIOS Version/Date American Megatrends Inc. 0503, 14.07.2009
SMBIOS Version 2.5
Windows Directory C:\Windows
System Directory C:\Windows\system32
Boot Device \Device\HarddiskVolume2
Locale Eesti
Hardware Abstraction Layer Version = "6.1.7600.16385"
User Name SemperFi-PC\Semper Fi
Time Zone FLE Standard Time
Installed Physical Memory (RAM) 4,00 GB
Total Physical Memory 4,00 GB
Available Physical Memory 2,10 GB
Total Virtual Memory 8,00 GB
Available Virtual Memory 5,47 GB
Page File Space 4,00 GB
Page File C:\pagefile.sys
I/O:
0x00000000-0x0000000F Direct memory access controller OK
0x00000000-0x0000000F PCI bus OK
0x00000010-0x0000001F Motherboard resources OK
0x00000020-0x00000021 Programmable interrupt controller OK
0x00000022-0x0000003F Motherboard resources OK
0x00000040-0x00000043 System timer OK
0x00000044-0x0000004D Motherboard resources OK
0x00000050-0x0000005F Motherboard resources OK
0x00000061-0x00000061 System speaker OK
0x00000062-0x00000063 Motherboard resources OK
0x00000065-0x0000006F Motherboard resources OK
0x00000070-0x00000071 System CMOS/real time clock OK
0x00000072-0x0000007F Motherboard resources OK
0x00000080-0x00000080 Motherboard resources OK
0x00000081-0x00000083 Direct memory access controller OK
0x00000084-0x00000086 Motherboard resources OK
0x00000087-0x00000087 Direct memory access controller OK
0x00000088-0x00000088 Motherboard resources OK
0x00000089-0x0000008B Direct memory access controller OK
0x0000008C-0x0000008E Motherboard resources OK
0x0000008F-0x0000008F Direct memory access controller OK
0x00000090-0x0000009F Motherboard resources OK
0x000000A0-0x000000A1 Programmable interrupt controller OK
0x000000A2-0x000000BF Motherboard resources OK
0x000000C0-0x000000DF Direct memory access controller OK
0x000000E0-0x000000EF Motherboard resources OK
0x000000F0-0x000000FF Numeric data processor OK
0x00000290-0x00000297 Motherboard resources OK
0x000003B0-0x000003BB Intel(R) X38/X48 Express Chipset PCI Express Root Port - 29E1 OK
0x000003B0-0x000003BB ATI Radeon HD 3850 OK
0x000003C0-0x000003DF Intel(R) X38/X48 Express Chipset PCI Express Root Port - 29E1 OK
0x000003C0-0x000003DF ATI Radeon HD 3850 OK
0x000003F8-0x000003FF Communications Port (COM1) OK
0x00000400-0x0000041F Intel(R) ICH9 Family SMBus Controller - 2930 OK
0x00000480-0x000004BF Motherboard resources OK
0x000004D0-0x000004D1 Motherboard resources OK
0x00000800-0x0000087F Motherboard resources OK
0x00000D00-0x0000FFFF PCI bus OK
0x00009400-0x0000940F Intel(R) ICH9R/DO/DH 4 port Serial ATA Storage Controller 1 - 2920 OK
0x00009480-0x0000948F Intel(R) ICH9R/DO/DH 4 port Serial ATA Storage Controller 1 - 2920 OK
0x00009800-0x00009803 Intel(R) ICH9R/DO/DH 4 port Serial ATA Storage Controller 1 - 2920 OK
0x00009880-0x00009887 Intel(R) ICH9R/DO/DH 4 port Serial ATA Storage Controller 1 - 2920 OK
0x00009C00-0x00009C03 Intel(R) ICH9R/DO/DH 4 port Serial ATA Storage Controller 1 - 2920 OK
0x0000A000-0x0000A007 Intel(R) ICH9R/DO/DH 4 port Serial ATA Storage Controller 1 - 2920 OK
0x0000A400-0x0000A40F Intel(R) ICH9 Family 2 port Serial ATA Storage Controller 2 - 2926 OK
0x0000A480-0x0000A48F Intel(R) ICH9 Family 2 port Serial ATA Storage Controller 2 - 2926 OK
0x0000A800-0x0000A803 Intel(R) ICH9 Family 2 port Serial ATA Storage Controller 2 - 2926 OK
0x0000A880-0x0000A887 Intel(R) ICH9 Family 2 port Serial ATA Storage Controller 2 - 2926 OK
0x0000AC00-0x0000AC03 Intel(R) ICH9 Family 2 port Serial ATA Storage Controller 2 - 2926 OK
0x0000B000-0x0000B007 Intel(R) ICH9 Family 2 port Serial ATA Storage Controller 2 - 2926 OK
0x0000B080-0x0000B09F Intel(R) ICH9 Family USB Universal Host Controller - 2934 OK
0x0000B400-0x0000B41F Intel(R) ICH9 Family USB Universal Host Controller - 2935 OK
0x0000B480-0x0000B49F Intel(R) ICH9 Family USB Universal Host Controller - 2936 OK
0x0000B800-0x0000B81F Intel(R) ICH9 Family USB Universal Host Controller - 2937 OK
0x0000B880-0x0000B89F Intel(R) ICH9 Family USB Universal Host Controller - 2938 OK
0x0000BC00-0x0000BC1F Intel(R) ICH9 Family USB Universal Host Controller - 2939 OK
0x0000C000-0x0000CFFF Intel(R) X38/X48 Express Chipset PCI Express Root Port - 29E1 OK
0x0000C000-0x0000CFFF ATI Radeon HD 3850 OK
0x0000D000-0x0000DFFF Intel(R) ICH9 Family PCI Express Root Port 6 - 294A OK
0x0000D800-0x0000D8FF Marvell Yukon 88E8056 PCI-E Gigabit Ethernet Controller OK
0x0000E000-0x0000EFFF Intel(R) ICH9 Family PCI Express Root Port 5 - 2948 OK
0x0000E400-0x0000E40F Standard Dual Channel PCI IDE Controller OK
0x0000E480-0x0000E483 Standard Dual Channel PCI IDE Controller OK
0x0000E800-0x0000E807 Standard Dual Channel PCI IDE Controller OK
0x0000E880-0x0000E883 Standard Dual Channel PCI IDE Controller OK
0x0000EC00-0x0000EC07 Standard Dual Channel PCI IDE Controller OK
0x0000FFE0-0x0000FFEF AS0MMTY9 IDE Controller OK
Drives:
Drive C:
Description Local Fixed Disk
Compressed No
File System NTFS
Size 149,05 GB (160 040 443 904 bytes)
Free Space 57,80 GB (62 065 405 952 bytes)
Volume Name
Volume Serial Number 44C64C64
Drive D:
Description Local Fixed Disk
Compressed No
File System NTFS
Size 149,05 GB (160 038 907 904 bytes)
Free Space 53,30 GB (57 233 891 328 bytes)
Volume Name Windows
Volume Serial Number 728D93DE
Drive E:
Description CD-ROM Disc
Drive G:
Description CD-ROM Disc
Disks:
Description Disk drive
Manufacturer (Standard disk drives)
Model SAMSUNG HD160JJ ATA Device
Bytes/Sector 512
Media Loaded Yes
Media Type Fixed hard disk
Partitions 1
SCSI Bus 1
SCSI Logical Unit 0
SCSI Port 5
SCSI Target ID 0
Sectors/Track 63
Size 149,05 GB (160 039 272 960 bytes)
Total Cylinders 19 457
Total Sectors 312 576 705
Total Tracks 4 961 535
Tracks/Cylinder 255
Partition Disk #1, Partition #0
Partition Size 149,05 GB (160 040 448 000 bytes)
Partition Starting Offset 32 256 bytes
Description Disk drive
Manufacturer (Standard disk drives)
Model WDC WD1600BB-00GUC0 ATA Device
Bytes/Sector 512
Media Loaded Yes
Media Type Fixed hard disk
Partitions 1
SCSI Bus 0
SCSI Logical Unit 0
SCSI Port 0
SCSI Target ID 0
Sectors/Track 63
Size 149,05 GB (160 039 272 960 bytes)
Total Cylinders 19 457
Total Sectors 312 576 705
Total Tracks 4 961 535
Tracks/Cylinder 255
Partition Disk #0, Partition #0
Partition Size 149,05 GB (160 038 912 000 bytes)
Partition Starting Offset 1 048 576 bytes
Multimedia shows me these codecs:
video:
c:\windows\system32\iyuv_32.dll Microsoft Corporation OK C:\Windows\system32\IYUV_32.DLL 6.1.7600.16385 52,50 KB (53 760 bytes) 14.07.2009 3:06
c:\windows\system32\msrle32.dll Microsoft Corporation OK C:\Windows\system32\MSRLE32.DLL 6.1.7600.16385 15,50 KB (15 872 bytes) 14.07.2009 3:18
c:\windows\system32\msvidc32.dll Microsoft Corporation OK C:\Windows\system32\MSVIDC32.DLL 6.1.7600.16385 37,50 KB (38 400 bytes) 14.07.2009 3:18
c:\windows\system32\msyuv.dll Microsoft Corporation OK C:\Windows\system32\MSYUV.DLL 6.1.7600.16385 24,00 KB (24 576 bytes) 14.07.2009 3:06
c:\windows\system32\tsbyuv.dll Microsoft Corporation OK C:\Windows\system32\TSBYUV.DLL 6.1.7600.16385 14,00 KB (14 336 bytes) 14.07.2009 3:06
c:\windows\system32\xfcode~1.dll Not Available Xfire video codec [XFR1] OK C:\Windows\system32\XFCODEC64.DLL 1.0.0.40405 26,89 KB (27 536 bytes) 30.11.2009 21:33
audio:
c:\windows\system32\imaadp32.acm Microsoft Corporation OK C:\Windows\system32\IMAADP32.ACM 6.1.7600.16385 21,50 KB (22 016 bytes) 14.07.2009 3:18
c:\windows\system32\l3codeca.acm Fraunhofer Institut Integrierte Schaltungen IIS Fraunhofer IIS MPEG Layer-3 Codec OK C:\Windows\system32\L3CODECA.ACM 1.9.0.401 79,50 KB (81 408 bytes) 14.07.2009 3:22
c:\windows\system32\msadp32.acm Microsoft Corporation OK C:\Windows\system32\MSADP32.ACM 6.1.7600.16385 23,50 KB (24 064 bytes) 14.07.2009 3:18
c:\windows\system32\msg711.acm Microsoft Corporation OK C:\Windows\system32\MSG711.ACM 6.1.7600.16385 14,50 KB (14 848 bytes) 14.07.2009 3:18
c:\windows\system32\msgsm32.acm Microsoft Corporation OK C:\Windows\system32\MSGSM32.ACM 6.1.7600.16385 28,50 KB (29 184 bytes) 14.07.2009 3:18
I downloaded and installed the Win7 codecs by Shark. Because...there are any other codecs available for win 7 ?
Tell me if need any more info..which u probably do.
If there are any better forums for this kind of problem then please tell me.
I hope we can fix this prooblem.
I think i haven't said my motherboard. Its P5E3 PRO. It has EPU engine and it turns off the hard drive when its idle...Premiere pro and all the sytem files are installed on my C drive which is like the main drive. On D drive i keep my music, downloads and stuff. I think it can turn of both drives then idle, but mostly it turns off D drive, I think. I have a new motherboard and i haven't got the hang of it how it shuts them down.
But i think this really isnt a problem.
Thanks in advance.

Serious hardware problems!
Go for a fresh install of OS & programs, but be prepared to first check your disks with a utility from the drive manufacturer (WD and Samsung). You may need new disks.
Great to include these details, but for readability I suggest you include these as an attachment instead of in the text. It may scare people off reading all that detail.

Error compiling movie 'unknown error' premiere elements 11, tried every troubleshoot, what now?

I'm trying to export a video and I keep on running into this error message, which stops the export process. I've already visited and tried the troubleshooting suggestions on this page and this page, and this page, and none of those suggestions have worked. Here's a list of what failed:
Export in various file formats, every single one failed
I removed each asset individually and tried to export the video after each removal (100+ assets, imagine how long that took) and I got the error after every single time
I removed the front half of the video and tried exporting, still failed.
I removed the back half of the video (because if it failed if I removed the front, the problem asset should be in the back, right? nope.) and tried exporting, it still failed.
I don't have any Auto Color, Auto Contrast, Auto Levels, or Shadow/Highlight on any of my clips, although if I did, I'd try removing them.
All of my video files are the same format, so it's not a mix of formats in my timeline which is causing the problem.
I tried disabling auto-save, but it already tried to auto-save during the first 20 times I've attempted this, so the damage might already be done.
I obviously didn't use any other programs during this process
I moved all my assets to a different location on my harddrive, then reopened the project and refound the assests one by one, each of which had no problem getting into the timeline. I tried rendering after this, and the render bar sailed along until a certain point, where it got stuck indefinitely. I cancelled the render, which froze the program. I had to close it and re-open the project, and re -link every asset again. Once again there were no problems adding the assets. I saved the project before the next render, so I wouldn't have to do this a third time, and it was a good idea I did, because the program froze again during the subsequent render.
My computer didn't go to sleep or hibernate during the first 5-10 times I tried various methods for exporting. It has slept in some of the 10+ times I've tried it since, because I don't have the patience to sit in front of my screen and watch it fail again and again and again and again and again and again and again and again and again and again and again and again and again and again and again and again and again and again and again. CAN YOU TELL THAT I'M FRUSTRATED???
The first thing I noticed that was wonky with this project was when I first tried to render my sequence. The render window chugged along just fine until it got to a certain point (can't remember the %), at which point it got stuck indefinitely. I had to cancel the render, and then render other parts of the sequence bit by bit, avoiding what I thought was the problem part. I tried rendering the problem part, and it got stuck again, so I eventually just decided that that clip didn't need to be in this movie, so I deleted it from the timeline. All should be good at this point, my whole timeline is green from being rendered. But, when I tried to export the video, I started down this tourtuous path of failed exports and frustration, and now here I am, posting in the forum, hoping someone can help me out.
The problem asset (if that was the problem in the first place) isn't in the timeline any more, but I'm still having issues exporting the movie. The fact that rendering still gets stuck after re-linking assets, and after getting rid of the first problem asset, makes me think that there is some bigger underlying issue, but I have no idea what that could be. I followed these instructions and re-opened the project, tried to export, and still got that 'Unknown Error'.
Please assist before I put my fist through this company computer.

maxlong99
Thanks for your update. Let us go through it.
You wrote
During one of my isolation tests, I stripped the timeline off all assets except clips from the same footage and I also removed that New Blue effect, and the project exported without issue.
Did you run a control which included "with the New Blue effect" in this isolated test which does not sound like the "Full Project" as suggested in what you wrote next?
You wrote
Could multiple renders and project files be part of the problem? I've created many, many different versions of this project to test and see where the problem is, which in turn means I've created many different render files for each different project. If this could be part of the problem, should I keep the original project and delete all my test projects and associated render files therein?
Each of the projects should have its own name which will be applied to its files. And each project should have rendered files specific to it (for SD project whether video or still clip = DV .avi file; for HD project whether video or still clip = MPEG2.mpg file). Are you naming these different projects with distinctive names?
Have you expanded the Timeline with the -+ slider and closely inspected the track content for
a. leftovers such a very thin vertical black lines scattered about
b. gaps
c. transitions, and especially audio placement
You have probably seen the following, but I will post the link just in case. I suspect you have been there and done that.
http://helpx.adobe.com/premiere-elements/kb/error-error-compiling-movie-render.html
Please let us know what the closer inspection of the Timeline content (as mentioned) revealed.
Thanks.
ATR

Error Compiling Movie - XF305 MXF Clip

I'm rendering a clip from a Canon XF305 using Premiere Pro version 7.2.1 on a Windows 7 i7-920, 48 GB, LSI 9286CV-8E that I've been using for 4 years starting with PR 5.0. The error is happening in the middle of the clip on the same frame. I'm exporting with Match Sequence Settings. The clip plays fine in PR and I don't see anything happening when I go frame by frame around the area where it gets the error. The file size when it gets the error is ~3GB and I have 3TB of available space on this RAID 6 disk.
The clip properties are:
File Path: T:\Video\XF305\CONTENTS\CLIPS001\SA0343\SA034301.MXF
Type: MXF
File Size: 1.9 GB
Image Size: 1920 x 1080
Frame Rate: 23.976
Source Audio Format: 48000 Hz - 16 bit - Stereo
Project Audio Format: 48000 Hz - 32 bit floating point - Stereo
Total Duration: 00:41:41:12
Pixel Aspect Ratio: 1.0
MXF File details:
Wrapper type: MXF OP1a (type: SingleItem SinglePackage MultiTrack Stream Internal)
File generated by: CANON, XF305
MPEG-2 422 Long-GOP
FIXED: Not sure what type of bug this is, but I did a cut just before and after the frames where the exporter would get the error and was able to export each cut of the clip without error. Now, I've been able to export the whole sequence. The only difference were the two cuts I made.
I created a new sequence with the original clips in the same project and it exported without error.
Has anyone had a similar problem?
Thanks,
Rob

Not me... but some saved messages about Error Compiling Movie
-http://helpx.adobe.com/premiere-pro/kb/error-compiling-movie-rendering-or.html
-and nested sequences http://forums.adobe.com/thread/955172

Export Error, Error compiling movie. "A low-level exception occurred in: H.264"

Hi
I'm still learning AE. I'd appreciate any help. I can export to Windows. Can't export to Vimeo SD 25 fps in H.264 either. When I try to compile via media encoder the following I get this message.
- Encoding Time: 00:00:00
07/30/2013 03:01:03 PM : Encoding Failed
A low-level exception occurred in: H.264 (Exporter)
Export Error
Error compiling movie.
Unknown error.
Movie Spec screen grabs:

Update: no error on the following, media encoder didn't throw any errors... must be the project. Disk cache is 120GB BTW. I was able was unable to run through YouTube HD 1080P 23.96 FPS.

PP CS4: Error compiling movie. I/O Error

I get this incessant I/O error any time I try to export a movie, regardless what format or
codec I am exporting to. I've tried this on a BRAND NEW Project with the same result.
I'm almost convinced that it's a problem or issue with Adobe Media Encoder? I tried to
export a GIF image with the result of:
Error compiling movie.
Unable to create or open output file.
Just five seconds ago, this is seriously driving me up a wall as I have my projects due
very very soon. ANY help would be greatly appreciated.
-jd

@ Harm Millaard
I'm not really sure what you mean by OE? Are you saying that its something to do with my hardware?
I had this running great in the past, before we changed buildings, I fired it up today to do some work
and no dice.
I insert a video, drag it to my time line, file > export and any option therein is wrong. The only thing I've
been able to export as is a static GIF, no AVI or etc....?
@ the_wine_snob
Actually I already did check out my Event Viewer prior to post, it came out with a clean bill besides
a few issues with my network not being able to update its dynamic ip (does not effect, has been doing
it for ages.) I used to be a computer tech so it was the first thing that I looked at. As for addressment
errors with hardware issues I'll have to wait until I get back to work tomorrow in order to check those
and make sure that I'm still running a tight ship.
I can tell you BOTH though that I am running a custom built Graphics Workstation put together by
me with no expense spared. I am running a Quadcore w/ 4gb high latency ram, and a 10k rpm hdd.
I believe that if there's a problem it would show itself in my other Adobe apps, and PS and AI seem
to scream, as well as After Effects, EnCore and other resource intense Master Suite apps.....?
This really has me scratching my head, I'm wondering if a full reinstall might be in order......

Error compiling movie

During publish + share operation I receive the following "Export Error" Error compiling movie. Unknown error.
The timeline plays through without any troubles and I rendered the footage before attempting to export. I read a vague tip that some of the clips may cause the error but how can you diagnose without individually removing every clip?
I am using trial version of Adobe Premiere Elements 13.1 (20150131.daily.767917) with Intel Core i5 2.4 GHz/ 8 GB RAM)/ 297 GB free hard disk space
Your cooperation is appreciated.
JS

JS
This is not Adobe. Rather user to user. But you would be going through the same drill I suspect either way if it offered you support.
Things will not get better going from tryout to purchased product....if there a flaw in the construction of your Timeline or a corrupt file, that will happen with tryout or purchased version. It is good that you are looking at the tryout before purchase.
You write
I am currently trouble-shooting clips and it appears that one of them is the cause...which one...hours later I am still deducing.
......this is a pretty clumsy way to trouble-shoot an issue (IMO).
Have you expedited matters in the strategy that you have used for the selective elimination troubleshooting
a. section by section...sort good from bad sections...you do not have to and should not start by eliminating clip by clip by clip
b. bad section breakdown
c. moving forward as indicated
Issue get troubleshooted as indicated by the user input. It would be good information to have with regard to the export involved
when the compiling error was triggered. Have you gone through a through d in my post 1 to rule each of those factors in or out?
What is the duration of the problem project? If it is a short project, have you considered starting a new project (redoing the old) and
determining if the compiling error hits again?
We will be watching for further developments.
ATR

Error compiling movie: out of memory !!! Premiere CS3

Hey every1 --- desperate need of some guidance here. I've been all over the internet and these boards --- have seen this come up with a lot of people but no real solid answers that I'd seen or that have helped.
First off, my comp is an imac 3.06 Ghz Core 2 Duo, 4GB memory. (just bought the computer last year)
I'm shooting with a canon 7d in HD (1920 x 1080p) and I'm editing using Premiere CS3. I've noticed that editing has become very difficult since I started using HD; playback is very choppy and the 'quality settings' in the preview monitor are a joke and do absolutely nothing whether it's on draft or automatic.
Anyway, despite the choppiness and slow editing, I was able to get a 3 min clip completed. These are my export settings:
Export > Movie
H.264
960 x 540
23.976 fps
Square pixels,
100% quality,
recompress: unchecked.
Once exported (I was able to export smaller timelines previously--- say, 50 secs of footage or so) the files look AMAZING and from there I use them for online video via vimeo -- stuff looks really awesome.
Anyway, recently I'm getting: 'Error compiling movie. Out of Memory. Change optimization preferences to memory', etc. etc. Well, I did as it asked and that did absolutely nothing.
So, I decided to open up my activity monitor and watch what's going on with my memory while premiere is exporting. I also closed ALL unused applications. System runs at about 2.16gb free memory before I start exporting. Memory seems stable during export UNTIL around the 50% exporting mark, and then its starts climbing like crazy and my memory just gets eaten up --- finally resulting in a crash at about 70% render.
I really don't know what else to do. Does my computer not have the power to export 3 min of HD footage??? This seems surprising to me ... I don't know what else to try.
Thanks for any help !!!
-Mark

Hi Mark,
Hope you are having a wonderful day.
Sorry to hear that you are having such a hard time. Although I did not specifically get the out of memory error, I can only be convinced that that is the problem.
Although I am not a computer whiz, I have learned my share of things. I have been troubleshooting a video all this week (really, a couple of months), but I had to put it aside and come back to it.
I tend to be talkative; so I will get back on topic or at least try to stay on topic, so bare with me. Smile....
Here is what I have learned and maybe it will help you with yours if you have not found a solution already.
Based on your hard drive specs and ram, I was thinking the same thing e.g. hard to believe that you are not able to render 3 minutes of video in HD. I primarily work in HD/1080p.
The place where we are similar is that I eventually could get the video to render by reducing the workspace that is rendered piece by piece until I was able to render the entire file. When I tried to encode the video, I kept getting error compiling messages. I tried different codecs, deleting xmpses, not rendering xmpses, etc. I could not figure out the keyframe trick so I just put in a black video from after effects. By the way, all of my videos intro the same and no problems with the other videos fading from black to a still photo.
Here is the problem from what I could gather.
Simply, out of memory. I was rendering and trying to encode a 45 minute video with after effects compositions and the dynamic linking kept timing out once the file reached a certain size. There were no other true fancy effects. I do alot on the green screen and just use after effects to make a white background. Smaller videos, rendering has been slow, but doable. This massive video would never compile. I won't bore you with my system specs, but know that similar to your situation, the system in theory should have been adequate.
Work around...
I ended up exporting the video as 3 separate 15 minute video clips. I could not get them to encode as .wmv files so I encoded them as .mp4 files. By the way, I still encoded in HD.
Here is the kool stuff.
After what seems like forever, I found a converter that could convert .mp4 to .wmv and rejoin the files to play as one large file with the same quality as my source file and no audio synching issues. By the way, I do not work for this company. I just found this encoder at 4 o'clock this morning after trying all of these other converters that were straight garbage or were free to try and not really free if you wanted quality. By the way, the conversion tool is not only user friendly, but free which is awesome.
The name of the software is Media Cope. Just visit www.mediacope.com.... Be sure to send the owner an e-mail to thank him and let him know that Mark sent you. I just sent him an e-mail earlier to let him know that I was going to post on Adobe what a wonderful software he created. I just needed something free, quick, easy, and user-friendly.
Whoops... got off topic....
I'll do a summary at the end for my recommendation to you.
Here are some other tidbits that I learned as well that may save you some time.
When editing this is what I do now...
1) I use CCleaner from www.piriform.com to quickly clean my system especially temporary files before I start editing and if I am switching from project to project.
2) In all of my troubleshooting this week, I found a kool little software call Smart Close. (Just google to find this one.) It closes all of your non-critical background files in order to maximize system resources. (When I am done editing, I just reboot and all of my background programs start up again. You do not have to do it that way, that's just how I do it. The nice thing is that it is a wizard interface; so you do not have to try to figure out if a process in the background is critical or non-critical.)
3) Depending on my mood and if I did not forget, smile.... I change the priority to high for the adobe products in the task manager.
More things that I learned...
1) We are not able to change the temp file for how Adobe encodes. My logic was if I could change the encoding to a hard drive that was simply empty so Adobe can render there, then I would be good. Wrong.... Adobe does not allow you to change the temp location. (Note: This is what I discovered in the different forums; so encoding to an external hard drive is not the best move. Read more to se why.)
2) It is best to have your scratch disks as your internal disk. If you have multiple internal disks, then you shoud check some other forums for the best way to set up your scratch disks. When I was just starting out, I bought an external hard drive enclosure with the thought that I would work primarily off of those external drives with the option of doing some RAID work. Bad idea... Even the simplest of tasks took forever. It was best to work off of the internal drive. By the way, I still use the enclosure hard drives for backups in order to allow me to free up some space on the primary hard drive. When rendering, it is truely a use of the RAM and the hard drive space in the editing process.
I'll leave you with this...
I take back what I said earlier, you do need a new computer with more RAM. If you can get 16 GB, great. The primary reason is that if you are editing in Premiere and if you do anything with dynamic linking into your after effects, it will cause your ram to climb as the file gets larger. Of course, be sure to get the largest hard drive possible as an internal drive, the maximum on processor speed, 64 bit operating system, etc.
I know you are like by now, Mark, what is the point of all of your gibberish... Really, it was to share with you and others on some really kool work arounds.
My recommendation for you are as follows.
1) You have already proven that you can render and encode 50 second clips and you are very happy with those clips, so create separate smaller clips for this particular project.
2) Once you have the final clips outputted, then use Media Cope to rejoin the files as one large file and you are done.
(Note: The one thing that I did notice is that there is a small break right between where the files are merged. The nice thing is that as a video editor/film maker, you will be the only person likely to notice it because you know where the breaks are. The other nice thing is that the untrained eye will not notice it and if you had to submit your work to a television station especially on DVD, the video system should recognize the file as one large file and play all the way through. Note: For the last sentence, I said 'should play all the way through' as I have not had a chance to check this one yet as I just finished this project today and still have to turn in all of my videos. I still have some more videos to merge.)
By the way, the only specs that I will share are that I work on a PC and it has 8 GB of ram.
The summary of the summary is that sometimes an error compiling message could simply be that your system does not have resources to render and the encode that large of a file. At least that is what I learned this week or at least my specific situation. The confirmation is that I just finished shooting a documentary which was one hour and some change and was able to render and encode to .wmv with no problems. Of course, I was not using after effects for this particular project.
In either case, hope all the information helps you with your project.
Have a wonderful day and happy holidays everyone.
Mark

Why is Premiere 6 giving a "Error writing file (disk full?)" message?

Hello helpful experts,
I'm using Premiere 6 on a Windows 7 machine.
I have a file imported in to the timeline and it is set to play in reverse via the speed setting being set to -100 and it plays back in the preview window correctly, in reverse, when I click the play button.
But when I do a "File>Export Timeline>Movie" command I get an error message saying "An error occurred while making the movie. Error writing file (disk full?)"... but my hard drive is not nearly full, with over 30 gigs left open on it... and my RAM usage gadget shows over half of my RAM capacity is unused.
Now previously, weeks ago on a different project, I was getting this same error message for a while when I would hit enter to preview my movie on the timeline (but that worked itself out somehow and eventually stopped giving me that error message). But when I went to save and export, then I would not get the error message... now, it is just the opposite... I'm now getting the error message when trying to do an export and save the movie.
And also now when I hit enter to preview, as opposed to just clicking the play button on the preview window, Premiere is going through the process of saving the movie since it is saving a temporary preview file... hopefully, since I'm getting this error message, I can find the temporary preview file and save it as my exported AVI file.
But I still shouldn't be getting this error message when trying to save, or when trying to preview, as I did for a while a couple of weeks ago.
Does anyone know about the erroneous error message that says, "An error occurred while making the movie. Error writing file (disk full?)"
Thanks,
numetro

Depending on your hard drive size, P6 may be confused... since drives were not as large when it was written
For Win7 64bit Pro or Ultimate (or Enterprise?) this is ONE example of using Virtual XP http://forums.adobe.com/thread/702693?tstart=0
This is saved from an OLD message that may help
File size limits by disk format type
Fat = 2 Gig maximum file size
Fat32 = 4 Gig
NTFS = ?Terrabytes?
Message saved from Premiere forum
John Acocks - 07:52am Apr 17, 2003 Pacific
I am unable to complete captures because I get a message
that says "capture stopped because disk was full." What
does this mean?
Daniel Conklin - 08:02am Apr 17, 2003 Pacific (#1 of 2)
If you are using a Pinnacle card, a possible solution to
this is to right click on the recycle bin, and set the
percentage on your media drive to less than 2%.
There a several other possible causes as well, but you
need to supply some info about your system. How are you
capturing and what format is your video? How big is
your hard drive?
Jeff Schell - 09:57am Apr 17, 2003 Pacific (#2 of 2)
this is one of my favorite error messages. Basically,
you've chosen an incorrect setting in your DV settings.
(Odds are you have DV settings). If so, read on:
1. The DV format is very rigid. Meaning that if you
   make changes to the format, it cannot export as
   requested, because your movie file must match every
   single spec exactly.
2. When Premiere goes to export a project, the DV codec
   says "Whoa. I can't do anything, because the settings
   don't match."
3. Then Premiere comes back to you and has to report an
   error. (Don't shoot the messenger). Unfortunately,
   Premiere doesn't know why it wasn't able to export a
   movie. So it says to you, "Um... I can't make the movie.
   Um... maybe your hard drives are full?"
It's a complete guess. And has nothing to do with your harddrives.
Check your project settings and/or your export settings. Make
sure you have chosen one of the "presets" that will specify
every correct setting for you. Make sure it is one of the DV
presets, if you are using DV video, or make sure it is one of
the presets supplied by your capture card manufacturer (in this
case I'm going to guess Pinnacle or Matrox.)
To choose a preset, go to Project > Settings Viewer, and then
click on the project settings column, and then click 'load' to
load a correct preset. Do the same with export settings.

Can't EXPORT or RENDER in PREM CC!! "Error compiling movie. Unknown Error."

I am using PMW200 MXF files alongside 5D MKiii files - I finished the edit and went to render/export and it won't let me do either! I can't get the edit out of the software and I have a deadline in an hour.
I only bought the software today (have been using the trial version and I am just coming from FCP 7 - I get this error:
"Error compiling movie. Unknown Error."

Hello Bill
The Adobe KB Article (http://helpx.adobe.com/premiere-pro/kb/error-compiling-movie-rendering -or.html ) does not answer the question asked, because the end of the error message is "Unknown error" which is not listed in this article.
I often encouter this error which is a RANDOM error which occurs only with pictures (4256x2832 .jpg or more when I use panoramic pictures with more than 50 MPx) but never with video (1920x1080 HD .m2ts) from my camcorder. The only way I found to do a complete render is :
- save and close the project without editing it,
- close Adobe Premiere Pro (CS6 or CC, same error),
- reopen Premiere Pro and reload the project,
- resume the render.
If I render WITHOUT Mercury Playback Engine : all is perfect, no error but the render needs very much more time.
My own conclusion : this render crash might be due to VRAM oveflooded during render with Mercury Playback Engine (this might be checked and monitored with the freeware GPU-Z).
My GPU is GTX 570 with 1280 MB VRAM and the render are only full HD (H.264 1920x1080i).
If you have a solution except remove the GPU and purchase a GTX 770 OC 4 GB VRAM, I am waiting for it.
My actual system :
- CPU Intel core i7 970 (6 cores, overeclocked to 3,9 GHz),
- MoBo : Intel DX58SO2,
- RAM : 24 GB,
- GPU GTX570 with VRAM 1280MB (Nvidia driver allways up-to-date),
- HDD : RAID 10 with four WD 1002FAEX (7200 tpm, 64 MB cache),
- OS W7 64 SP1, 64 bits (allways updated)
Regards
Jacques

Error compiling movie. Disk Full.

Similar Messages

Maybe you are looking for