(Error disabled. Reason:Disabled by Server Mgr triggered)

I´ve some ports in my Nexus 5k going to err-disable with the following message:
(Error disabled. Reason:Disabled by Server Mgr triggered)
These ports are connected in HPBlade 7000 through FEX Nexus B22 does someone know about this errors ?

Hi,
Not sure if you already found the root cause of the issue,but this message generally comes from blade FEX's when there is an internal communication error or no connection between the FEX HIF's and the server chassis/software. This might come when a port is made "admin up" while is not configured or mapped blade from server perspective.
Thanks,
Ivan.

Similar Messages

Nexus 5500 - Fabricpath Core Port - Error disabled. Reason:DCX-No ACK in 100 PDUs

Has anyone seen Fabricpath Core Interfaces between two Nexus 5596UP switches error-disabled because of missing DCBX Acks after 50mins?
I do not see interface errors and the peer is another 5500.
Both switches are running 5.1(3)N2(1) with this port config:
int e1/3
switchport mode fabricpath
! Cisco 5m Twinax cables
Log messages
2012 May 25 17:40:59 nexus1 %L3VM-5-FP_TPG_INTF_DOWN: Interface Ethernet1/3 down in fabricpath topology 0 - Interface down
2012 May 25 17:40:59 nexus1 %ETHPORT-5-IF_DOWN_NONE: Interface Ethernet1/3 is down (None)
2012 May 25 17:40:59 nexus1 %ISIS_FABRICPATH-5-ADJCHANGE: isis_fabricpath-default [3365] P2P adj L1 nexus5 over Ethernet1/3 - DOWN (Delete All) on MT-0
2012 May 25 17:40:59 nexus1 %CDP-5-NEIGHBOR_REMOVED: CDP Neighbor nexus5(FOX1550GDH1) on port Ethernet1/3 has been removed
2012 May 25 17:40:59 nexus1 %LLDP-5-SERVER_REMOVED: Server with Chassis ID 547f.ee63.fa88 Port ID Eth1/1 on local port Eth1/3 has been removed
2012 May 25 17:40:59 nexus1 %ETHPORT-2-IF_DOWN_ERROR_DISABLED: Interface Ethernet1/3 is down (Error disabled. Reason:DCX-No ACK in 100 PDUs)
Robert

Can you send the output of
show lldp interface ethernet 1/3
show lldp dcbx interface ethernet 1/3
a workaround may be to disable lldp on both sides on these physical interfaces

Error disabled. Reason:DCX-No ACK in 100 PDUs

Hi,
I have a customer who lost all connectivity from the ESX host for both networking and FCoE because (as the title suggests) the interfaces were error disabled. This happened across all 8, dual ported, dual homed CNAs at the same time. Does anyone have any idea what this error comes from? The are using ESX 4.0 and are running Nexus 5020 with 4.2(1)N2(1a).
Thanks,
Thom

DCBX Type Length Values(TLV) are packaged within a LLDP frame which is exchanged between the switch and the CNA. One such Control Sub-TLV is used for ACK which is sequence based. For example, the switch sends this control Sub-TLV with SeqNo of 1 and AckNo of 2. The host is supposed to inverse this and send a LLDP frame with control sub-TLV with SeqNo of 2 and AckNo of 1.
We expect this exchange every 30 seconds from the host and if the switch does not see it for 100 times 30 which is 3000 seconds (or 50 minutes), the switch error disables with following error
2011 May 13 12:03:23 CSX_5020_A1 %ETHPORT-2-IF_DOWN_ERROR_DISABLED: Interface Ethernet115/1/17 is down (Error disabled. Reason:DCX-No ACK in 100 PDUs)
2011 May 13 12:03:27 CSX_5020_A1 %ETHPORT-2-IF_DOWN_ERROR_DISABLED: Interface Ethernet116/1/16 is down (Error disabled. Reason:DCX-No ACK in 100 PDUs)
Some commands on the switch which helps in narrowing down root cause.
F340.24.10-5548-1# show lldp interface ethernet 1/22
Interface Information:
Enable (tx/rx/dcbx): Y/Y/Y    Port Mac address: 00:05:73:ab:29:bd
Peer's LLDP TLVs:
Type Length Value
001 007    040000c9 9d2372
002 007    030000c9 9d2372
003 002    0078
006 045    456d756c 6578204f 6e65436f 6e6e6563 74203130 4762204d 756c7469
            2066756e 6374696f 6e204164 61707465 72
007 004    00800080
127 055    001b2102 020a0000 00000002 00000001 04110000 c0000001 00003232
            00000000 00000206 060000c0 00080808 0a0000c0 00890600 1b2108
000 000
F340.24.10-5548-1# show lldp dcbx interface ethernet 1/22
Local DCBXP Control information:
Operation version: 00 Max version: 00 Seq no: 1 Ack no: 2 <<---Our sequence # and Ack #
Type/
Subtype    Version    En/Will/Adv Config
003/000     000        Y/N/Y      0808
004/000     000        Y/N/Y      8906001b21 08
002/000     000        Y/N/Y      0001000032 32000000 00000002
Peer's DCBXP Control information:
Operation version: 00 Max version: 00 Seq no: 2 Ack no: 1 <<---Peer sequence # and Ack # should be reversed.
Type/      Max/Oper
Subtype    Version    En/Will/Err Config
002/000     000/000    Y/Y/N      0001000032 32000000 00000002
003/000     000/000    Y/Y/N      0808
004/000     000/000    Y/Y/N      8906001b21 08
F340.24.10-5548-1#
Root cause for this problem in most cases is misbehaving CNA/server or incorrect firmware/driver on the CNA.

ISE error disable interface

Dears
After configuring DOT1x on access ports , some ports show error disabled without enabling the port-security , is their any way to increase the number of MAC addresses allowed on the port ? , is it possible to disable this feature
Sent from Cisco Technical Support iPhone App

Hi Eng.malak,
The port config provided by you the interface GigabitEthernet1/0/2 is configured for MDA that means an IP phone and a single host behind the IP phone are authenticated independently, even though both the IP phone and host machine are connected to a single switch port on the switch. If more than once device is detected in either domain, a security violation will be triggered. This can be a problem when a phone fails to authenticate properly. If a phone fails authentication, then the switch does not receive the "device-traffic-class=voice" VSA from the radius server and the switch will assume that the failed device was in the data domain. However if there is already a data device behind the phone, there will be now 2 devices in the data domain, and a security violation is triggered. On this port only 2 MAC addresses are allowed. The switch place the client machine in a data vlan and the IP phone in a voice vlan.
Configure the violation mode. The keywords have these meanings:
authentication violation shutdown | restrict | protect | replace}
•shutdown-Error disable the port.
•restrict-Generate a syslog error.
•protect-Drop packets from any new device that sends traffic to the port.
•replace-Removes the current session and authenticates with the new host.
Configuring 802.1x Violation Modes
http://www.cisco.com/en/US/docs/switches/lan/catalyst3560/software/release/12.2_55_se/configuration/guide/sw8021x.html#wp1324086
~BR
Jatin Katyal
**Do rate helpful posts**

Cisco Prime Infrastructure 2.1 error-disable alert

We have a cisco PI 2.1 managing switches and a lot of switchports have BPDUGuard enabled. When occur error-disable , request send email notification to administrator .
By default, when a port of a switch goes down, the Prime generates alarm for that. (this is a problem, because every laptop disconnection will generate alarm for administrator)
Can i change the alert just for error-disable and how to ?
Thanks

Causes of Errdisable
This feature was first implemented to handle special collision situations in which the switch detected excessive or late collisions on a port. Excessive collisions occur when a frame is dropped because the switch encounters 16 collisions in a row. Late collisions occur after every device on the wire should have recognized that the wire was in use. Possible causes of these types of errors include:
A cable that is out of specification (either too long, the wrong type, or defective)
A bad network interface card (NIC) card (with physical problems or driver problems)
A port duplex misconfiguration
A port duplex misconfiguration is a common cause of the errors because of failures to negotiate the speed and duplex properly between two directly connected devices (for example, a NIC that connects to a switch). Only half-duplex connections should ever have collisions in a LAN. Because of the carrier sense multiple access (CSMA) nature of Ethernet, collisions are normal for half duplex, as long as the collisions do not exceed a small percentage of traffic.
There are various reasons for the interface to go into errdisable. The reason can be:
Duplex mismatch
Port channel misconfiguration
BPDU guard violation
UniDirectional Link Detection (UDLD) condition
Late-collision detection
Link-flap detection
Security violation
Port Aggregation Protocol (PAgP) flap
Layer 2 Tunneling Protocol (L2TP) guard
DHCP snooping rate-limit
Incorrect GBIC / Small Form-Factor Pluggable (SFP) module or cable
Address Resolution Protocol (ARP) inspection
Inline power
Note: Error-disable detection is enabled for all of these reasons by default. In order to disable error-disable detection, use the no errdisable detect cause command. The show errdisable detect command displays the error-disable detection status.

Scripting disabled by Server

Hi,
I want to run following script to check SAP-GUI sessions.
In rz11 sapgui/user_scripting_per_user is set to "TRUE" - but the script means, that guiConn.DisabledByServer is true!!
Though I cannot connect to an existing SAPGUI-session.
Any idea?
Tnx.
Now the script
WScript.echo("connecting to SAP GUI")
Set sapGUI = GetObject("SAPGUI")
If(sapGUI Is Nothing) Then
    WScript.echo("ERROR: No SAP GUI found")
    WScript.Quit 1
End If
WScript.echo("SAP GUI connected, connecting to script engine")
Set guiApp = sapGUI.GetScriptingEngine
If(guiApp Is Nothing) Then
    WScript.echo("ERROR: scripting engine not available")
    WScript.Quit 1
End If
WScript.echo("Scripting Engine available")
WScript.echo(" Version " & CStr(guiApp.MajorVersion) & "." & CStr(guiApp.MinorVersion) & " Patch " & CStr(guiApp.PatchLevel) & " Revision " & CStr(guiApp.Revision))
WScript.echo(CStr(guiApp.connections.Count) & " connection(s) available")
For Each guiConn In guiApp.Connections
    WScript.echo(" connection " & guiConn.description)
    WScript.echo("    disabled by server : " & CStr(guiConn.DisabledByServer))
    WScript.echo("    connection string : " & CStr(guiConn.ConnectionString))
    if(guiConn.Sessions.Count > 0) then
        set guiSess = guiConn.Sessions(0)
        WScript.echo("    application server : " & CStr(guiSess.Info.ApplicationServer))
        WScript.echo("    message server     : " & CStr(guiSess.Info.MessageServer))
        WScript.echo("    group              : " & CStr(guiSess.Info.Group))
        WScript.echo("    system name        : " & CStr(guiSess.Info.SystemName))
        WScript.echo("    system number      : " & CStr(guiSess.Info.SystemNumber))
        WScript.echo("    client             : " & CStr(guiSess.Info.Client))
        WScript.echo("    user               : " & CStr(guiSess.Info.User))
        WScript.echo("    language           : " & CStr(guiSess.Info.Language))
        WScript.echo("    code page          : " & CStr(guiSess.Info.CodePage))
    end if
    WScript.echo("    sessions           : " & CStr(guiConn.Sessions.Count))
    For Each guiSess In guiConn.Sessions
        WScript.echo("    session " & CStr(guiSess.Info.SessionNumber))
        WScript.echo("      busy : " & CStr(guiSess.Busy))
        WScript.echo("      session information")
        WScript.echo("        transaction        : " & CStr(guiSess.Info.Transaction))
        WScript.echo("        program            : " & CStr(guiSess.Info.Program))
        WScript.echo("        screen number      : " & CStr(guiSess.Info.ScreenNumber))
        WScript.echo("      performance information")
        WScript.echo("        response time      : " & CStr(guiSess.Info.ResponseTime))
        WScript.echo("        interpretation time: " & CStr(guiSess.Info.InterpretationTime))
        WScript.echo("        flushes            : " & CStr(guiSess.Info.Flushes))
        WScript.echo("        round trips        : " & CStr(guiSess.Info.RoundTrips))
    Next
Next
WScript.Quit 0
And this is the output

Hi,
Not sure if you already found the root cause of the issue,but this message generally comes from blade FEX's when there is an internal communication error or no connection between the FEX HIF's and the server chassis/software. This might come when a port is made "admin up" while is not configured or mapped blade from server perspective.
Thanks,
Ivan.

Error disable due to loopback

Hi,
We have a campus network. A student's hostel room port that is connected to a 2960 switch get error-disabled time and again and it shows the reason being "loopback".
From switch patch panel to user's LAN port in room , we have tested the connectivity through cable tester and it is found to be proper.
He has changed his LAN cable also, what can be the exact reasons causing this problem

Thanks for the output to the command "sh version".
Look at the uptime of the switch. Because of this the output to the "loopback_error_2960" is totally useless. Why? If there was any line errors which can determine if there was a cabling issue, a NIC card issue or something more sinister, then there's only 4-days worth of data. Not much to run with.
The IOS is very, very old.
Currently, the only thing I can think of is remove the configuration of setting the speed to the port to 10 Mbps. (I don't see the benefit of punishing students by slowing down their network speed.) Once the port is running auto speed/auto duplex, wait for approximately 30 minutes and run a TDR on the port. Even better if you can move the cable to the GigabitEthernet port and run the TDR there so you'll get a better picture of all the pairs.
Another thing, post the output to the command "sh post".

Vfc error disabled because of Ethernet port down?

We are building a new datacenter and is starting to set up the SAN.
This small DC consist of 2 Nexus 5596UP, a Compellent SAN and 2 Dell M1000e cassis with blade servers.
naive FC part in Nexus has been easy to set up but we have problems with the FCOE setup.
Since the blades are not installed yet none of the Ethernet ports are up. As soon as we bind an ethernet port to a vfc the vfc goes to error disable with this message:
%PORT-2-IF_DOWN_ERROR_DISABLED: %$VSAN 1900%$ Interface vfc101 is down (Error disabled)
Config snippets:
vlan 1900
fcoe vsan 1900
name VSAN-A-FCOE
vlan 1901
name VSAN-B-FCOE
vsan database
vsan 1900 name "VSAN-A"
vsan 1901 name "VSAN-B"
interface vfc101
bind interface Ethernet1/1
no shutdown
vsan database
vsan 1900 interface vfc101
vsan 1900 interface fc2/13
vsan 1900 interface fc2/14
vsan 1900 interface fc2/15
vsan 1900 interface fc2/16
interface Ethernet1/1
switchport mode trunk
spanning-tree port type edge trunk
vlan 1900
fcoe vsan 1900
name VSAN-A-FCOE
vlan 1901
name VSAN-B-FCOE
vsan database
vsan 1900 name "VSAN-A"
vsan 1901 name "VSAN-B"
vsan database
vsan 1900 interface vfc101
vsan 1900 interface fc2/13
vsan 1900 interface fc2/14
vsan 1900 interface fc2/15
vsan 1900 interface fc2/16
interface vfc101
bind interface Ethernet1/1
no shutdown
interface Ethernet1/1
switchport mode trunk
spanning-tree port type edge trunk
Do the vfc go error disable because the ethernet interface being down? I was under the impression it should just go "down"

What you are seeing is normal.. Here are outputs from my lab switch where I shut Eth1/20 which is tied to vFC 20
24.10.5020A.1(config)# int ethernet 1/20
24.10.5020A.1(config-if)# shut
2011 Oct 21 10:16:01 24 %ETHPORT-5-IF_DOWN_CFG_CHANGE: Interface Ethernet1/20 is down(Config change)
2011 Oct 21 10:16:01 24 %FLOGI-5-MSG_PORT_LOGGED_OUT: %$VSAN 100%$ [VSAN 100, Interface vfc20: mode[TF]] Nx Port 21:00:00:c0:dd:12:0e:35 logged OUT.
2011 Oct 21 10:16:01 24 %PORT-5-IF_PORT_QUIESCE_FAILED: Interface vfc20 port quiesce failed due to failure reason: Epp Not Supported by Peer (0x19d)
2011 Oct 21 10:16:01 24 %PORT-5-IF_DOWN_NONE: %$VSAN 100%$ Interface vfc20 is down (None)
2011 Oct 21 10:16:01 24 %PORT-2-IF_DOWN_ERROR_DISABLED: %$VSAN 100%$ Interface vfc20 is down (Error disabled)
2011 Oct 21 10:16:02 24 %ETHPORT-5-IF_DOWN_ADMIN_DOWN: Interface Ethernet1/20 is down (Administratively down)
24.10.5020A.1(config-if)#

Error disabled ports

I have a 3550 switch that gets a error-disabled copper ports. There is no errors ont the port. What else would cause it to be disabled?

Although there is no error on the port , there should be an error message in the log that should tell you the reason why the port got error disabled like port security violation , loopback detection , etherchannel misconfig etc.
You can enable errordisable recovery for all different causes by setting a timer. What happens is once this timer expires , the port is brough out of error dsiabled state.
Here are some of the useful commands.
D-C3550-2A(config)#errdisable ?
detect Error disable detection
recovery Error disable recovery
D-C3550-2A(config)#errdisable recovery ?
cause Enable error disable recovery for application
interval Error disable recovery timer value
Hope this helps.
Salman Z.

Nexus 4k error disable

Anyone ever seen this before? Trying to understand why the port error disabled.
2011 Jan 18 11:53:09 MTWDAVDC1BLDB9001 %ETHPORT-2-IF_DOWN_ERROR_DISABLED: Interface Ethernet1/1 is down (Error disabled. Reason:requested by sap: MTS_SAP_DCX, req down_type: 2, req down_reason: 222 )
MTWDAVDC1BLDB9002# sh int eth1/1
Ethernet1/1 is down (DcxMultipleMSAPs)
Hardware: 1000/10000 Ethernet, address: 0027.0d23.4d8d (bia 0027.0d23.4d8d)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 10 Gb/s, media type is 10g
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
Last link flapped 1d03h
Last clearing of "show interface" counters never
1 minute input rate 0 bits/sec, 0 packets/sec
1 minute output rate 0 bits/sec, 0 packets/sec
Rx
    153349455 input packets 143221479 unicast packets 3730739 multicast packets
    6397237 broadcast packets 0 jumbo packets 0 storm suppression packets
    66448449173 bytes
Tx
    328643307 output packets 90031378 multicast packets
    113132871 broadcast packets 12877361 jumbo packets
    62121338327 bytes
    0 input error 0 short frame 0 watchdog
    0 no buffer 0 runt 0 CRC 0 ecc
    0 overrun 0 underrun 0 ignored 0 bad etype drop
    0 bad proto drop 0 if down drop 0 input with dribble
    1416 input discard
    0 output error 0 collision 0 deferred
    0 late collision 0 lost carrier 0 no carrier
    0 babble
    0 Rx pause 0 Tx pause
8 interface resets

I looked into the error and would suggest opening a TAC case so our engineering team can look into this error. You can open a case using the supportforum as well to turn the thread into a case.
Sorry to not be able to help more, but looks like our internal team needs to look into this further.
Chad

Error-disabled cause by loopback?

Hello All,
Does anyone please explain me about error-disabled cause by loopback? What is loopback? When does it happen? And why?
Thank you very much,
Nitass

This happens usually with IP Phones using power over ethernet. Hope this link helps
http://www.cisco.com/en/US/products/hw/phones/ps379/products_field_notice09186a008031575e.shtml
Iam not sure of any other reasons though,

Campus Manager report - Ports in error Disabled state

Hi,
I have LMS 3.2 and I wonder how Campus Manager collects information from the switch to generate a report of discrepancies, namely a report of "Ports in Error Disabled state"??
I find that I have ports in errDisabled state but Campus Manger doesn´t show this information in "Ports in Error Dissabled state" report. What could be the problem?
Thanks.

Hi,
Campus Manager do snmpwalk on the ciscoErrDisableMIB to get the status of the error disabled ports.
Thanks,
Gaganjeet Singh

UDLD Detection & Error Disable On Cat 6513

Hi
We have a problem with an etherchannel trunk between 2 Cat 6513's. The etherchannel is 8Gb split across 2 Copper 10/100/1000Mb 16 port cards in each chassis. The trunk uses ports 13 - 16 on slot 5 in one chassis to 13 - 16 on slot 5 in the other chassis and 13 - 16 on slot 6 in one chassis to 13 - 16 in slot 6 on the other chassis.
We appear to have had a UDLD Detection which error disabled all 4 of the links from slot 6 to slot 6 at the same time. IE ports 13 - 16 on slot 6 of both chassis went into error disabled state.
Could this be a ASIC hardware problem on one of the cards? If so, how do we establish which end of the trunk the problem exists? All other connections on these slot 6 cards are working fine.

UDLD is a protocol that discovers if communication over a link is one-way only, and therefore partially broken. A damaged fiber cable or other cabling/port issue could cause this one-way only communication. Spanning tree loops can occur with this problem. UDLD allows the port to detect a unidirectional link, and can be configured to put a port in errDisable state when it detects this condition.

Non-SysAdmins get error 18456 Severity 14 State 11 Login Failed for user _ Reason Token-based server access validation failed with an infrastructure error.

I have a SQL 2008 R2 system (10.50.4000) where I'm having problems connecting any user that is not a SysAdmin. Example: I setup a new SQL Login to use Windows Authentication and grant that user db_datareader on the target database. The user attempts
to connect using Excel client or Access or SQL Management Studio and receives Error 18456. The SQL Server Logs shows Error 18456 Severity 14 State 11 Login Failed for user _ Reason Token-based server access validation failed with an infrastructure error.
The strange part is that if I temporarily grant the user the sysadmin server role then the user can connect successfully and retrieve data. But, if I take away that sysadmin server role then the user can no longer connect but again receives the Error
18456 Severity 14 State 11 Login Failed for user _ Reason Token-based server access validation failed with an infrastructure error.
We've turned off UAC on the client machine to see if that was the problem, but no change.
I have dropped and re-added the user's SQL Login (and the related database user login info). No success.
The Ring Buffers output shows:
The Calling API Name: LookupAccountSidInternal
API Name: LookupAccountSid
Error Code: 0x534
Thanks for any help.
-Walt

Yes, you understand correctly. The user is logging onto a workstation (not the server) with a Windows Authenticated id. The user is using either Excel or Access or SSMS and connecting to the server using a Windows Authenticated SQL Login account.
If the account has sysadmin role (which is only for testing) then the connection is successful. If I take away sysadmin role from the account then the connection is unsuccessful and the SQL Server Log shows Error
18456 Severity 14 State 11 Login Failed for user _ Reason Token-based server access validation failed with an infrastructure error.
(SQL Authentication is not an option here. I must use Windows Authentication).
Any other troubleshooting assistance you can offer would be appreciated. Thanks.
-Walt

Java - Shared archive: sharing disabled for server vm ?

Hi,
My mac is PowerMac G5(1.8Ghz) + leopard server 10.5.1.
I have a question.
After typing *java -version*, the following messages are shown.
*Shared archive: sharing disabled for server vm*
*java version "1.5.0_13"*
*Java(TM) 2 Runtime Environment, Standard Edition (build 1.5.0_13-b05-237)*
*Java HotSpot(TM) Client VM (build 1.5.0_13-119, mixed mode)*
What is *Shared archive: sharing disabled for server vm* ?
Using my other macs, iMac(Intel 1.8GHz) and PowerBook G4(1.5GHz) + leopard client-10.5.1,
the message is
*java version "1.5.0_13"*
*Java(TM) 2 Runtime Environment, Standard Edition (build 1.5.0_13-b05-237)*
*Java HotSpot(TM) Client VM (build 1.5.0_13-119, mixed mode, sharing)*
So, the difference is "sharing".
Anyone know what it means?

I'm getting the same message. I'm intrigued. This would seem to be something to do with the new version of Java
Java(TM) 2 Runtime Environment, Standard Edition (build 1.5.0_13-b05-237)
Java HotSpot(TM) Client VM (build 1.5.0_13-119, mixed mode, sharing)
I don't get the message when doing java -version, but I do get it when starting JBoss:
./run.sh: line 80: ulimit: open files: cannot modify limit: Invalid argument
run.sh: Could not set maximum file descriptor limit: unlimited
=================================================================
JBoss Bootstrap Environment
JBOSS_HOME: /usr/local/jboss-4.0.2
JAVA: java
JAVA_OPTS: -server -Xms256m -Xmx512m -Dprogram.name=run.sh
CLASSPATH: /usr/local/jboss-4.0.2/bin/run.jar:/lib/tools.jar
=================================================================
Shared archive: sharing disabled for server vm
15:42:09,736 INFO [Server] Starting JBoss (MX MicroKernel)...
It doesn't seem to cause any trouble, but it would be good to know what it's all about (man java doesn't help).
Bruno.

(Error disabled. Reason:Disabled by Server Mgr triggered)

Similar Messages

Maybe you are looking for