Error during install of Mini WAS 6.20

All,
I'm getting the following error message(s):
InfoExtracting the Database-Dependent SAP system Executables
Warning: CDSERVERBASE ConfirmKey 2 816
Can not read from F:. Please ensure this path is accessible.
Info: LvKeyRequest
For further information see HTML documentation:
step: EXTRACTSAPEXEDBDATA2 and key: DATA1_LOCATION
Warning: CDSERVERBASE ConfirmKey 2 816
Can not read from E:. Please ensure this path is accessible.
Info: LvKeyRequest
For further information see HTML documentation:
step: EXTRACTSAPEXEDBDATA2 and key: DATA1_LOCATION
Warning: CDSERVERBASE ConfirmKey 2 816
We tried to find the label SAPDB:MINI-WAS-DEMO:620:DATA1 for CD DATA1 in path E:\. But the check was not successfull.
Info: LvKeyRequest
For further information see HTML documentation:
step: EXTRACTSAPEXEDBDATA2 and key: DATA1_LOCATION
I first tried the CD1, which was in drive F:, that didn't work, then I put CD3 into drive E:, that didn't work and at last I added the \ to the E: and that didn't work either, so once more the frustration continues.
I read the other posts but none of the solutions works for me. Further more the installation guide is not quite right either (what a surprise). It shows that the installation program wants to have the location of the 3 CDs defined. I never get to see that screen. I started all over, didn't work either.
Now I'm stuck with 3 CDs and cannot do anything with them.
Hope somebody can help, since there is no technical hotline available.
Uwe

The 3 disks are:-
Disk 1, 'Kernel'.
Disk 2, 'Data1'.
Disk 3, 'Data2'.
You will be asked to confirm their location at 25, 41, and 44% of the process.
MattG.

Similar Messages

  • Error During INSTALL of Application Export File

    An error is reported during INSTALL of an application that I am trying to copy (Import/Install) from a "development" Work Space into a "production" Work Space. The production (target) Work Space is on the same HTML DB instance as the development Work Space.
    I am receiving the following INSTALL error:
    ORA-20001: GET_BLOCK Error. ORA-20001: GET_STMT error. ORA-20001: Execution of the statement was unsuccessful. ORA-06550: line 15, column 1: PLS-00103: Encountered the symbol ",'39','RD8','8','S','10','U','43','UD','41','UG','11','W')) END)" when expecting one of the following: . ( * @ % & = - + ; < / > at in is mod remainder not rem <an exponent (**)> <> or != or ~= >= <=
    Following is some pertinent (hopefully) information:
    The above INSTALL error takes exception to part of a Region Select (sql) that works fine in the development Work Space.
    The common HTML DB (v1.6) instance is on UNIX.
    A new Work Space was created on the same instance.
    A new schema name was created during creation of the new Work Space. However, this schema does not point to a database. (We were not certain how to setup the schema to parse to our live database.) I will be running DBLINK upon production application startup in order to access the database objects.
    EXPORT INFO -
    File Format: UNIX (also, tried DOS but received same error during INSTALL)
    IMPORT INFO -
    File Type: Application/Page Export
    File Character Set: Western European Windows 1252
    Target Work Space is newly created on the same HTML DB instance.
    INSTALL INFO -
    *Parse As Schema: COLLIVE17 (Again, this schema does not parse to a database. I intend to use DBLINK.)
    *Build Status: Run and Build Application
    Please refer to above error message.
    Again, any insights or suggestions are appreciated.

    Urgently need help! I've read several other Forum messages having a related problem but none having same Install error message.
    Again, my Export/Import from development Workspace to production Workspace is successful. The following error is reported when I attempt to "Install" into the production Workspace:
    ORA-20001: GET_BLOCK Error. ORA-20001: GET_STMT error. ORA-20001: Execution of the statement was unsuccessful. ORA-06550: line 15, column 1: PLS-00103: Encountered the symbol ",'39','RD8','8','S','10','U','43','UD','41','UG','11','W')) END)" when expecting one of the following: . ( * @ % & = - + ; < / > at in is mod remainder not rem <an exponent (**)> <> or != or ~= >= <=
    The "snippet" of Region Sql Select code that relates to the reported error is:
    ELSE htmldb_item.display_and_save (5, DECODE (GET_GRADE_B93 (sac.stc_final_grade,sac.stc_verified_grade),'18','AU','1','A','3','B','4','C','7','CR','5','D','46','DR','6','F','47','FW','49','IB','30','IC','31','ID','23','IF','44','MW','9','NC','21','RD','14','RD0','33','RD1','32','RD2','34','RD3','35','RD4','36','RD5','37','RD6','38','RD7','39','RD8','8','S','10','U','43','UD','41','UG','11','W'),'GRADE_'||ROWNUM) END q_v_grade,
    HTML DB version is: 1.6.0.00.67. I've also tried to Export/Import/Install the application into the "same" Workspace specifying the same schema, and only changing the Application ID. However, I get the same Install error (see above).
    Any suggestions on things to try in order to get application into production is greatly appreciated.
    Thanks, Bernard.

  • Errors During Instalation Of Final Cut Studio 5.1

    Aloha,
    I am having some trouble here!! I am trying to install FCP Studio Pro 5.1 on my mac. I tried to do an upgrade from FCP 4.5 HD on my orriginal Hard drive. The instalation went through its paces & asked me to put in the second disc. I did then it came back with an anoucment that there were errors during instalation & to try again I did & was never able to get it to instal... Getting frustrated I ran diskworior on the drive & tried again no luck... after some time I thought it might be the drive would not let me because there was an earlier version on there.... so any way after some other problems with this drive I decided to completely erase & instal Mac OSX on my second hard drive that has never had anything on it. I made this my new startup disk & upgraded the OS to OS 10.4.9 I then Tried to install FCP Studio Pro 5.1 on this drive.. this time It never got to ask me to put in another disk it came back with the same error during instalation try again!!!!!! So now I am getting ******!! but odly enough Final cut studio shows up in my aplications. When I click on it it gives me a warning that there was an error registering & once I click ok it seems to launch FCP 5.1....... ?? So is it really there or not??? & why is it not installing the other 4 discs??? and to add insult to this I have tried to install iLife 06 & I get the same error!!!! WHY!!!!!!!!!
    Another thing.. I installed FCP Studio Pro 5.1 on another Identical computer down the street & it installed no problem!!!!
    Can anyone help Please!!!!!!

    I would take a different approach.
    I would backup the old drive files to an external, and then do a clean wipe and new install of OS, updates and the FCS.
    Best way to do it, in my view.

  • Error during Addon Installation Index was outside the bounds of array

    Hi  wen im trying to install addon on x64 2003 server its throwing me error
    Customer library
    "Error during Addon Installation Index was outside the bounds of array."
    "Error(-2) at EndInstallEx(False) at the end of the addon installation"
    Please provide me a solution for this.
    Thanks
    Rekha

    Hi Rekha,
    You may check this: Add-on Installer Issue
    Is this your add-on or SAP add-on? If it is 3rd party add-on, post it to the other forum
    Thanks,
    Gordon

  • OMS error during install Grid control 10gR2 on Windows 2003

    He,
    I get this error during install Grid control 10gR2 on a new server win2003.
    "oracle.sysman.emcp.agent.AgentPlugIn"
    What I see in forums is that I have to stop my listener and continue my installation.
    But I still have the same error !!
    Can you please help?
    Many thanks

    There are some guidelines here:
    Subject:      OracleAS Install Error When Configuring AS Console Agent - "oracle.sysman.emcp.agent.AgentPlugIn has failed"
         Doc ID:      Note:386308.1
    The solution stated is "Check the contents of the hosts of file and ensure that every entry is correct. All hostname / ip addresses have to be valid."
    When installing AS 9i R2 there was an issue with the names, those were supposed not to hava a hypen, so may be something was inherited from those kernels.
    There is another metalink note that document hosts issues:
    Problem: AgentCA: Grid Control Release 2 install fails with java.lang.Exception: 6 during Agent Configuration Assistant
         Doc ID:      Note:358640.1
    ~ Madrid.

  • Integrity constraint error during install

    We have installed htmldb on zlinux from the companion CD.
    Because we had an error during install of the flows schema we repeat it (have removed the Flows-User and Flow-Files before) using ins.sql! The apache was still running.
    Most of the new installation was fine but near the end we got:
    error creating "Procedure arguments" id=122 Ora-01400, cannot insert NULL into ("FLOWS_010500,"WWv_Flows_STEPS","SECURITY_GROUP_ID")
    declare
    Error at line1
    Ora-02291- integrity constraint(FLOWS_0150000.WWV_FLOW_PLUG_ZO_PAGE_FK) violated
    parent key not found
    ORA-06512 at "FLOWS_01500.WWV_FLOW_API line 4695
    ...

    OK, it's solved:
    I finally managed to install Apex 3.0 correctly once I figured out my error.
    I was logging in remotely to the server the dadbase was on, then trying to connect to sqlplus using 'sys/password@instance as sysdba' to run the script.
    Turns out that the problem had something to do with sys not being allowed to be sysdba when I log in remotely, or that having the username/password and instance info in there made the program think I was logging in remotely and therefore not giving me sysdba privileges.
    The root of the problem was running the install .sql without the correct privileges.
    Since I found out the database server I was trying to install on uses OS authentication, I remote-connected to the database server as the oracle user, tried to run the install .sql again after connecting to sqlplus: 'conn / as sysdba'
    and everything worked like a charm!
    ~PF :)

  • Solution for Power Saver error during install

    Hello,
    i have read several topics about the powersaver error during install of this utilty.
    i had the same problem even with a clean install of windows XP and i have found the solution.
    The error seems to disapear and Powersaver works fine after install of the Hotkey utility :
    http://support.toshiba-tro.de/tools/Satellite/sa60/win-xp/hotkey-dd/hotkey-dd-xp-10008sa-du.zip
    Hope this post where helpfull.
    Greetz DeLorean
    [Edited by: admin]

    Hi
    You are absolutely right. Common modules is a kind of basic application who must be installed first. All other Toshiba tools should be installed after. The functionality of Power saver utility depends also on installed common modules.
    Unfortunately I can not give you any kind of advice but in case that there is some error message the best solution is to remove and install the Power saver again. Check also Toshiba download page. Maybe you can find a newer version.
    Bye

  • Quicktime errors during install, uninstall, or run

    Quicktime errors during install, uninstall, or run. No error code. It just says it encountered an error and must exit.

    I located a previous response that satisfied my issue. Below is the process that allowed me to use quicktime.
    The "fatal error" in this context has (recently) been indicating trouble with old, misplaced QuickTime componentry lurking about in your system.
    (Whether or not the message is a symptom of that problem seems to depend on what version of old misplaced stuff is lurking and what version of QuickTime proper we're trying to install or uninstall ... but in recent times, there's been an uptick in fatal errors being caused by that.)
    So let's try investigating that possibility first.
    First we'll adjust some view settings on the PC.
    1. Open My Computer from the desktop or Start menu.
    2. In the Tools menu, click Folder Options.
    3. Click the View tab.
    4. In the "Advanced settings" pane under "Hidden files and folders" make sure that the "Show hidden files and folders" option is selected, and the "Hide extensions for known file types" option is unchecked.
    5. Click OK.
    Now in "My Computer" open Local Disk C: (or whichever drive your operating system is installed on).
    Open the "Windows" folder.
    Open the "System32" folder.
    What files or folders can you see in there with QuickTime in the file or folder name? (In a standard installation of QuickTime, you should see precisely two files ... QuickTime.qts and QuickTimeVR.qtx ... and no QuickTime folders whatsoever.)

  • FCP error during install.

    I keep getting an error after installing FCP 5.1.1.
    It says error during install please try again.
    Im using 10.4.7 on my ibook 1ghz 640mb ram.
    I know it will work because a friend has installed it on his.
    Any one help?

    This most often caused by a damaged or otherwise faulty disk in the package. It happens. Try cleaning the disks and then get out your receipt and serial number because your only recourse will be to call Apple for a replacement.
    bogiesan

  • WRT160N error during install

    I just purchased WRT160N and during the install of LELA there is an error. " Linksys Updater failed to start- verify you have sufficient privileges to start system services" pops up during install.  Then it asks to retry and it hasn't worked or close window.  Then when says this "Setup for Linksys Advisor has failed "Fatal Error During Install" please check your settings and try again.
    Help!  I am not computer savy, and don't want to start changing anything and screw it up.
    Internet is working on the installed computer (I believe this is called the gateway? not wireless uses the ethernet cable)but I can't setup my wife's new laptop til this is fixed.
    BTW this is a cable modem hook up if that makes a difference.  I have tried restarting, turning power off as well but still get the same problem every time.
    Thanks,
    Don

    As you have mentioned that your Hardwired computer is able to go online throught the router, and now you are trying to setup your wireless computer. You dont have to run the setup disk on your computer, you can configure all the settings on your Router manually and then make your Wife's computer go online wirelessly..
    Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave username blank & in password use admin in lower case...
    For Wireless Settings, please do the following : -
    Click on the Wireless tab
    - Here select manual configuration...Wireless Network mode should be mixed...
    - Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
    - Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
    Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
    For Wireless Security : -
    Click on the Sub tab under Wireless > Wireless Security...
    Change the Wireless security mode to WEP, Encryption should be 64 bit.Leave the passphrase blank, don't type in anything...Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...
    Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
    Click on Advanced Wireless Settings
    Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
    Now see if you can locate your Wireless Network and attempt to connect...

  • Error During install Exchange 2013 through Powershell on Server 2012 "Mailbox role: Client Access service"

    Dear all
    During install Exchange 2013 through Powershell on Server 2012 I got this error in Mailbox role: Client Access service :
    The following error was generated when "$error.Clear();
    $BEVdirIdentity = $RoleNetBIOSName + "\OWA (Exchange Back End)";
    new-OwaVirtualDirectory -Role Mailbox -WebSiteName "Exchange Back End" -DomainController $RoleDomainController
    set-OwaVirtualdirectory -Identity $BEVdirIdentity -FormsAuthentication:$false -WindowsAuthentication:$true;
    " was run: "An error occurred while creating the IIS virtual directory 'IIS://MONAMBX2.mona.local/W3SVC/2/ROOT/o
    wa' on 'MONAMBX2'.".
    The following error was generated when "$error.Clear();
    $BEVdirIdentity = $RoleNetBIOSName + "\OWA (Exchange Back End)";
    new-OwaVirtualDirectory -Role Mailbox -WebSiteName "Exchange Back End" -DomainController $RoleDomainController
    set-OwaVirtualdirectory -Identity $BEVdirIdentity -FormsAuthentication:$false -WindowsAuthentication:$true;
    " was run: "The operation couldn't be performed because object 'MONAMBX2\OWA (Exchange Back End)' couldn't be fo
    und on 'MonaDc1.mona.local'.".
    Any advice please !!

    I can't answer your question but I had a similar issue when I was trying to move our mailbox database off the C: drive.  Our environment still has an Exchange 2007 server in it and when I was trying to move the database on the 2013 server, I would get
    error messages saying the database does not exist.  It seemed like it was trying to move the database on the 2007 server from the similar error messages that I was getting.  To get around it, I deleted the database and created a new one on the drive
    where we wanted it.
    I discovered this when I was configuring the Antispam settings.  I deleted our 2007 settings, added them to the 2013 shell, the settings appeared on our 2007 server.  The shell on 2013 was making changes to 2007.
    I'm not sure if there is a "Get|Set or New" command that I/we should be using when this happens.  Or maybe my issues will be fixed if I just remove the Exchange 2007 server?  I'm not ready to do that yet because I can't configure the spam filtering
    on 2013 yet with its shell not being able to make the changes that we need.
    I don't know if your environment is in coexistence mode like mine.
    Hopefully someone else out there has an answer or can tell us when/how the shell can make the appropriate changes to the 2013 server.  Does this happen after the 2007 server is removed?

  • Itunes error during install service apple mobile device failed to start.. help

    I had to install Chrome browser in order to use my gmail account.  Now I cannot open itunes on my Window Vista computer, get a Microsoft Visual C++ Runtime Library. R6034. I uninstall itunes and reinstall itunes 64-bit itunes installer.  During install received error during the 'starting services' process "Service 'Apple Mobile Device' (Apple Mobile Device) failed to start. Verify that you have sufficient privelges to start sytem services. I ignore with the same error message so I abort. At the end of uninstalling I received the Microsoft Visual C++ Runtime Library error again. I click ok than an error from itunes. "itunes was not installed correctly. Please reinstall itunes. Error 7 (Windows error 1114). I click ok.  Help.. 

    Try the following user tip:
    Troubleshooting issues with iTunes for Windows updates

  • Error during install of the iTunes 11.0.1 update on Windows Vista

    Error during the process of installing the iTunes update to 11.0.1, when iTunes attempts to write to file C:\Config.msi\b530a0c.rbf. iTunes says it can't access that directory, but i'm installing iTunes as an Administrator.  And i don't find the specified file in this directory on my c:\ drive

    I seem to have solved this problem as follows:
    1.  Download the iTunes.exe file from apple.com, but save the file to my Desktop rather than running it.
    2.  Execute (double click) the iTunes.exe file from my Desktop.
    3.  When i encountered the problem that i've reported (the iTunes installer announces that it can't access a file in the c:\config.msi directory, i clicked the Retry button in the error window.  The iTunes installer process appeared to move past the error.
    4.  I experienced the same error one more time during my apparently successful iTunes 11.0.1 install, but the 2nd time this error came up iTunes reported that it was trying to access a different file name in the c:\config.msi directory.  Again, i clicked the Retry button in the error window and the iTunes installer appeared to move on past the error.

  • "WRITE SAME failed. Manually zeroing." error during install or boot

    Hello everyone!
    Since the lasts kernels (I'm almost sure it happens since 3.9 because 3.8 worked fine) I can't boot on Archlinux anymore. This error floods my screen and I can't do anything, and because the new Archlinux iso (june 2013) comes with 3.9 kernel it now also happens during installation. Fortunately, I saved the may iso so I still can install archlinux and switch during install to LTS kernel but this is not a good solution. I can't find a solution online, some people have this issue but it seems to be a bit different everytime.
    I use Archlinux on a server, with hardware raid : Dell PERC H200a with LSI SAS2008 according to my BIOS. According to http://kernelnewbies.org/Linux_3.7, the WRITE SAME SCSI command "allows the same block to be efficiently replicated throughout a block range. Only a single logical block is transferred from the host and the storage device writes the same data to all blocks described by the I/O (commit)". Here is the exact configuration :
    - DELL® PowerEdge R210 II
    - 1x Intel® Xeon® E3 1220 V2
    - HDD: 2 x 1 To SATA2 RAID
    - RAID: Hardware, Dell PERC H200, (Raid 1)
    So my first problem is that I can't find online if my server is capable of this command (but I don't think so) and then the other issue is that I want to know if I can disable it. I found kernel patches for this issue :
    https://patchwork.kernel.org/patch/1898441/ and https://patchwork.kernel.org/patch/1982051/ (the first link seems to be a better solution).
    Then, I checked in the kernel source of 3.9 and I think that this patch isn't implemented (there is no device_write_same_capable function for instance). But kernel patching is not a really good solution, if I have to patch my kernel everytime the main kernel is updated...
    After some research, I found that my hardware RAID driver seems (I'm not sure) to be the kernel module "mpt2sas", so I checked both may and june isos of Archlinux and it's the same version (14.1) so it shouldn't be the problem.
    Does somebody can help me on this issue ? I don't really know what to do now.
    Thanks for reading, if I forgot something or if you want more informations, ask me!
    Bye.
    PS : My English isn't very good, sorry.
    EDIT : I found a part of the solution ! It seems to be an issue with the kernel that doesn't detect properly if my disc is capable of doing WRITE SAME command.
    So I have to write "0" in the file "max_write_same_blocks" under /sys. But the problem is that /sys is renewed every boot so I don't know how to make my changes permanent. I made a systemd service file, it almost works, but this solution isn't nice : the parameter is applied lately so errors shows at the beginning and this is not really easy to set up. I prefer a solution like "sysctl" but it seems that it only controls parameter under /proc/sys and not /sys, am I right ?
    Moreover, I tried two other things : Ubuntu 12.04 with kernel 3.9.4 works and Archlinux iso with 3.8.10 has max_write_same_blocks > 0 and it also works... So I don't really understand this issue. Maybe in 3.8 the parameter max_write_same_blocks has no effect (or not the same as in 3.9) ?
    Here is the systemd file that I made to reduce the issue :
    [Unit]
    Description=No WRITE SAME
    After=local-fs.target
    [Service]
    Type=oneshot
    ExecStart=/bin/sh -c 'echo 0 > /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/host0/target0:1:0/0:1:0:0/scsi_disk/0:1:0:0/max_write_same_blocks'
    RemainAfterExit=no
    [Install]
    WantedBy=multi-user.target
    This is not a good solution, see my next post. I don't delete it in case you want to compare.
    Last edited by rfnx (2013-06-02 15:26:50)

    I found a solution to disable the WRITE SAME command. That doesn't answer all my questions but it solves my issue. I was looking for a file like "sysctl.conf" but for /sys parameters : you already can do that in Arch, just create a file that ends with ".conf" in tmpfiles.d and add one line per parameter you want to modify. This file will be loaded early at boot.
    To disable it in an existing Archlinux installation, add in you file the line :
    w /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/host0/target0:1:0/0:1:0:0/scsi_disk/0:1:0:0/max_write_same_blocks - - - - 0
    Read the manpage of tmpfiles.d if you don't understand this line, it depends on your configuration and you can't copy it.
    Then reboot and no more error !
    If you want to disable it during the Arch install, just change directly the value you want in /sys. You have to do it at the beginning before mounting partitions, for instance just after choosing your keymap.
    Bye.
    Last edited by rfnx (2013-06-02 15:34:11)

  • Linking errors during install on Linux Mandrake

    When I installed oracle (8.1.7) on linux mandrake I got a series of errors during
    the very last portion of the install involving a bunch of *.mk files.
    The first error says:
    Error invoking target relink of makefile
    $ORACLE_HOME/precomp/lib/ins_precomp.mk
    All the others are virtually identical. I'm still pretty new to linux so I avoided
    recompiling the kernel. Aside from that I followed the install instructions to the
    letter. If anyone knows whats going on I would very much appreciate a push in
    the right direction.

    Alright, I've tried using the most recent archboot (2011.02-2) a couple times. I selected GRUB2 x86_64 EFI. It asked me whether or not I wanted to convert my existing MBR to GPT. When I say no, it says installation was successful, when I say yes, it drops me into parted, so I just quit. My GPT should be fine as is.
    My issue is that now, in rEFIt, I only get OS X and Legacy OS options. Legacy just freezes my computer. The legacy option has been there since I last tried to install, though I've tried to get rid of it a few different ways.
    Should I choose a different bootloader option? Can I use the cd to boot in and fix it manually? if possible, I'd like to keep using rEFIt.

Maybe you are looking for

  • WIndows 7 Pro 64 bit rebooting after installing flash player 11.4

    Hi There, I was wondering if anyone could help me to solve the problem I am encountering with my home computer which after installing adobe flash player keeps on rebooting soon after it gets to the logon screen and other times whilst I am playing CSS

  • Artist Sorting Issues or displaying artist name on iPod.

    Hello, I have been struggling with this for a while now and it's really becoming irksome. I have to have a compliation CD displayed as Various Artists when searching through my iPod on Artist browse mode, yet once the individual songs are played i wa

  • Sync cable for BlackBerry Flip 8230

    I recently bought a Blackberry Flip 8230 to replace my (lost) Blackberry 8130.  I tried to synch it tonight with the old cord for my other Blackberry but it did not fit.  I can't remember if a synch cord comes with the phone or is it something I have

  • IPhoto only partially updates albums after syncing

    I purchased iPhoto after I upgraded my iPad 4 to iOS 7 so I don't know if this is a new problem or not. What happens is whenever I change out albums on my PC and synch my iPad iPhoto acts very strange. It shows the new albums and new images but it tr

  • Trackpad not level

    My trackpad is very slightly wobbely/uneven and makes a sound when I'm scrolling that drives me crazy. It's like a table where one of the legs is slightly shorter than the others.  On my trackpad it happens to be the lower left corner.  It wobbles in