Error during MaxDB upgrade from 7.3.00.42 to 7.5.00.32

Hello all,
I am attempting to upgrade from MaxDB 7.3.00.42 to 7.5.00.32, as part of a migration from HP-UX 11.11 to Windows Server 2003.  The MaxDB database supports a Content Server 6.30 application, and from what I have found so far, I need to upgrade/patch to 7.5.00.51 on the HP-UX server, before I can migrate using the loadercli (as per note 962019).
While performing the upgrade to 7.5.00.32 (following the steps in the Upgrade Guide to MaxDB 7.5), I receive the following error.
chperm 660 sdb:sdba /sapdb/data/config/SDB.mmm
user sdb can access /sapdb/data/config/SDB.mmm
remove /sapdb/data/wrk/dbmsrv.prt
remove /sapdb/data/wrk/SDB.knl
remove /sapdb/data/wrk/SDB.mdf
permissions for databases as of version 7.5.00 are used on your system
database owner is sdb
administrators group is sdba
owner of SDB is sdb (sdba sdba)
user_logon failed
Obviously there is a permissions problem of some kind, but I have not been able to pinpoint where.  I allowed the DDUPDATE.SH script to create the user SDB, and it appears to have been created successfully and was used during the earlier steps of the upgrade script.
While working with SAP support I confirmed that I could connect to the database using the SDB user and I also executed the sdbverify, which completed successfully.  As per the upgrade guide, I am logged in to HP-UX as root when running the upgrade (and when I ran sdbverify).
If anyone has suggestions on the cause of this error, I would greatly appreciate any assistance.
Best Regards,
Rusty Robbins

Isn't that how it always goes...
I have been fighting this for 4-5 days, and had replied back and forth with support, with no luck on a resolution.  But of course just as soon as I post my question here, support comes back with the answer!.  I guess that just goes to show how good the SDN site is!  ;p
Anyway, the answer to my problem was related to the group permissions on this HP-UX server. The ddupdate script did create the SDB user and set the primary group as SDBA, which normally would give the SDB user all rights for that group.  However, in this case the error continued to occur, until I explicitly added the user SDB to group SDBA (at the request of SAP support).  This upgrade step did finish successfully, and I am now continuing on with the other steps to migrate to Windows.  Hopefully the rest of the steps will go smoother...
Regards,
Rusty Robbins

Similar Messages

  • Load_systab ERR_EXECUTE during MAXDB upgrade

    Hello,
    I performed MAXDB upgrade from 7.7.04.028 to 7.8.01.014.
    During the upgrade I received the following message:
    load_systab
    -24964,ERR_EXECUTE: error in program execution
    768,/sapdb/EFL/db/bin/sdbsysload -R /sapdb/EFL/db -d EFL -u superdba,*
    Installing tables for instances
    ----------Command----------------
    DROP PACKAGE SYS_DDL_PACKAGE
    -----------Error-----------------
    Unexpected error -9205
    But I could see that the version was updated and I could start the system. So I applied the patch to upgrade to 7.8.02.024.
    If I execute load_systab from dbmcli, I still get the same message, and in Database Studio -> Diagnosis files-> Database error, the following entry appear:
    620:  Thread      0xE91 Task    570  2011-09-08 15:59:52 ERR SYSERROR   51080:  AK Catalog information not found:ãu20ACu20ACãu20ACu20ACãu20ACu20ACãu20ACu20ACãu20ACu20ACãu20ACu20ACãu20ACu20AC
    Could you please help me, and tell me how this affects my system?
    Thank you in advance

    Hello,
    1. Are you SAP customer?
        Did you download  7.8.02.024 version?
        7.8.02.024. is not released for free download at www.sdn.sap.com/irj/scn/maxdb-downloads
       MAXDB 7.8.02.25 Server Package  released for SAP customers.
    2. If you are SAP customer => Did you create the SAP message where this issue was reported?
    Regards, Natalia Khlopina

  • Role of Time Mgmt functional consultant during SAP Upgrade from 4.7 to ECC6

    Hi,
    Could anyone explain the role of a time management functional consultant during SAP upgrade from R/3 4.7 to ECC6.0. Please provide me if you got any documentation.
    Thanks,
    Sunny

    "After you upgrade to SAP ERP 6.0, you can enhance the functionality of your application without performing a further
    upgrade thanks to a new deployment technology u2013 the SAP enhancement package for SAP ERP. The enhancement
    packages simplify the way you manage and deploy new software functions for SAP ERP." - that is the real benefit of ECC 6.0
    There aren't any major changes to PTM functionalities from 4.7 to 6.0. I hope your system is already using IT 2006 instead of IT 0005. Under functional role, you are required to configure/test any functional upgrade and manage data.
    Regards
    Yash

  • Error during the upgrade phase "start_shdi_first"

    Hello,
    We are having issue with upgrading r/3 4.7 enterprise extension set to ECC 6.0
    Here the error message goes....
    starting system failed rc=0
    to analyse the error during start of shadow instance
    view files 'Startsfi.log' and 'devtrace.log'
    in directory usr\..put
    repeat phase until shadow instance is started
    and u can logon instance no '01'"
    We have changed the DDIC password during upgrade.after that we ran the initphase to update the password.
    I think sapup is referring the old password which was entered initially during the upgrade and we dont remember the old password also.
    Appreciate your response
    Startsfi.log
    1 ETQ201XEntering upgrade-phase "START_SHDI_FIRST" ("20080218175653")
    2 ETQ366 Connect variables are set for shadow instance access
    4 ETQ399 System-nr = '01', GwService = 'sapgw01'
    4 ETQ399 Environment variables:
    4 ETQ399   dbs_mss_schema=de4
    4 ETQ399   auth_shadow_upgrade=1
    4 ETQ399 Set environment for shadow connect:
    4 ETQ399 ENV: dbs_mss_schema=de4
    4 ETQ399 ENV: auth_shadow_upgrade=1
    4 ETQ399 Set RFC variables for shadow connect:
    4 ETQ399 System-nr = '01', GwService = 'sapgw01'
    4 ETQ399 Set tool parameters for shadow connect:
    4 ETQ380 computing toolpath for request "TP_SHADOW_CONNECT"
    4 ETQ381 request "TP_SHADOW_CONNECT" means "tp needs to connect to shadow system"
    4 ETQ382 translates to group "R3UP_TOOL_GROUP_NEW"
    4 ETQ383 translates to path "exe"
    4 ETQ383 translates to path "exe"
    4 ETQ399   default TPPARAM: SHADOW.TPP
    4 ETQ380 computing toolpath for request "TP_ALWAYS_NEW"
    4 ETQ381 request "TP_ALWAYS_NEW" means "always tp from DIR_PUT/exe, for phase KX_SWITCH"
    4 ETQ382 translates to group "R3UP_TOOL_GROUP_NEW"
    4 ETQ383 translates to path "exe"
    4 ETQ383 translates to path "exe"
    2 ETQ399 Starting shadow instance
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2 ETQ353 Starting system
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-3"
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-3"
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-3"
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-3"
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-3"
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-3"
    2 ETQ370 starting test RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    4 ETQ233 Calling function module "UPG_IS_SHADOW_SYSTEM" by RFC
    4 ETQ359 RFC Login to: System="DE4", Nr="01", GwHost="MTW02SDEC01", GwService="sapgw01"
    4 ETQ232 RFC Login succeeded
    2EETQ235 Call of function module "UPG_IS_SHADOW_SYSTEM" by RFC failed (error-status "-3")
    4 ETQ239 Logging off from SAP system
    2WETQ372 test RFC failed, rc="-3"
    2EETQ399 Starting shadow instance failed
    2EETQ399 Test RFC failed finally
    2EETQ399 Dialogue: ERROR
    2EETQ399 Starting system failed, rc=0
    DEVTRACE:
    trc file: "dev_disp", trc level: 1, release: "700"
    sysno      01
    sid        DE4
    systemid   560 (PC with Windows NT)
    relno      7000
    patchlevel 0
    patchno    111
    intno      20050900
    make:      multithreaded, ASCII, optimized
    pid        2272
    Mon Feb 18 16:08:40 2008
    kernel runs with dp version 229(ext=109) (@(#) DPLIB-INT-VERSION-229)
    length of sys_adm_ext is 364 bytes
    SWITCH TRC-HIDE on ***
    ***LOG Q00=> DpSapEnvInit, DPStart (01 2272) [dpxxdisp.c   1239]
         shared lib "dw_xml.dll" version 111 successfully loaded
         shared lib "dw_xtc.dll" version 111 successfully loaded
         shared lib "dw_stl.dll" version 111 successfully loaded
         shared lib "dw_gui.dll" version 111 successfully loaded
         shared lib "dw_mdm.dll" version 111 successfully loaded
    rdisp/softcancel_sequence :  -> 0,5,-1
    Mon Feb 18 16:08:52 2008
    WARNING => DpNetCheck: NiHostToAddr(www.doesnotexist0065.qqq.nxst) took 12 seconds
    Mon Feb 18 16:09:10 2008
    WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 18 seconds
    ***LOG GZZ=> 2 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c  5361]
    MtxInit: 30000 0 0
    DpSysAdmExtInit: ABAP is active
    DpSysAdmExtInit: VMC (JAVA VM in WP) is not active
    DpIPCInit2: start server >MTW02SDEC01_DE4_01                      <
    DpShMCreate: sizeof(wp_adm)          19976     (908)
    DpShMCreate: sizeof(tm_adm)          3605136     (17936)
    DpShMCreate: sizeof(wp_ca_adm)          18000     (60)
    DpShMCreate: sizeof(appc_ca_adm)     6000     (60)
    DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528040/528048
    DpShMCreate: sizeof(comm_adm)          528048     (1048)
    DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0
    DpShMCreate: sizeof(slock_adm)          0     (96)
    DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
    DpShMCreate: sizeof(file_adm)          0     (72)
    DpShMCreate: sizeof(vmc_adm)          0     (1296)
    DpShMCreate: sizeof(wall_adm)          (22440/34344/56/100)
    DpShMCreate: sizeof(gw_adm)     48
    DpShMCreate: SHM_DP_ADM_KEY          (addr: 065C0040, size: 4241064)
    DpShMCreate: allocated sys_adm at 065C0040
    DpShMCreate: allocated wp_adm at 065C1B30
    DpShMCreate: allocated tm_adm_list at 065C6938
    DpShMCreate: allocated tm_adm at 065C6968
    DpShMCreate: allocated wp_ca_adm at 06936BF8
    DpShMCreate: allocated appc_ca_adm at 0693B248
    DpShMCreate: allocated comm_adm at 0693C9B8
    DpShMCreate: system runs without slock table
    DpShMCreate: system runs without file table
    DpShMCreate: allocated vmc_adm_list at 069BD868
    DpShMCreate: allocated gw_adm at 069BD8A8
    DpShMCreate: system runs without vmc_adm
    DpShMCreate: allocated ca_info at 069BD8D8
    DpShMCreate: allocated wall_adm at 069BD8E0
    MBUF state OFF
    DpCommInitTable: init table for 500 entries
    EmInit: MmSetImplementation( 2 ).
    MM global diagnostic options set: 0
    <ES> client 0 initializing ....
    <ES> InitFreeList
    <ES> block size is 1024 kByte.
    Using implementation view
    <EsNT> Using memory model view.
    <EsNT> Memory Reset disabled as NT default
    <ES> 2046 blocks reserved for free list.
    ES initialized.
    WARNING => System running without ICM - check rdisp/start_icman [dpxxdisp.c   12437]
    rdisp/http_min_wait_dia_wp : 1 -> 1
    ***LOG Q0K=> DpMsAttach, mscon ( MTW02SDEC01) [dpxxdisp.c   11753]
    DpStartStopMsg: send start message (myname is >MTW02SDEC01_DE4_01                      <)
    DpStartStopMsg: start msg sent
    CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
    CCMS: start to initalize 3.X shared alert area (first segment).
    DpMsgAdmin: Set release to 7000, patchlevel 0
    MBUF state PREPARED
    MBUF component UP
    DpMBufHwIdSet: set Hardware-ID
    ***LOG Q1C=> DpMBufHwIdSet [dpxxmbuf.c   1050]
    DpMsgAdmin: Set patchno for this platform to 111
    Release check o.K.
    Mon Feb 18 16:09:13 2008
    MBUF state ACTIVE
    DpModState: change server state from STARTING to ACTIVE
    trc file: "dev_ms", trc level: 1, release: "700"
    [Thr 4724] Mon Feb 18 16:08:40 2008
    [Thr 4724] MsSSetTrcLog: trc logging active, max size = 20971520 bytes
    systemid   560 (PC with Windows NT)
    relno      7000
    patchlevel 0
    patchno    110
    intno      20050900
    make:      multithreaded, ASCII, optimized
    pid        5420
    [Thr 4724] ***LOG Q01=> MsSInit, MSStart (Msg Server 1 5420) [msxxserv.c   1824]
    [Thr 4724] MsInitAclInfo: acl file D:\usr\sap\put\DE4\SYS\global\ms_acl_info.DAT not found, unrestricted access
    [Thr 4724] MsGetOwnIpAddr: my host addresses are :
    [Thr 4724]   1 : [172.20.28.159] MTW02SDEC01.mindsap.com (HOSTNAME)
    [Thr 4724]   2 : [127.0.0.1] MTW02SDEC01.mindsap.com (LOCALHOST)
    [Thr 4724] MsHttpInit: full qualified hostname = MTW02SDEC01.mindsap.com
    [Thr 4724] HTTP logging is switch off
    [Thr 4724] MsHttpOwnDomain: own domain[1] = mindsap.com
    [Thr 4724] ms/icf_info_server : deleted
    [Thr 4724] *** I listen to port sapmsSHDDE4 (3601) ***
    [Thr 4724] CUSTOMER KEY: >J1537289841<
    trc file: "dev_rd", trc level: 1, release: "700"
    Mon Feb 18 16:09:10 2008
    ***LOG S00=> GwInitReader, gateway started ( 2344) [gwxxrd.c     1694]
    systemid   560 (PC with Windows NT)
    relno      7000
    patchlevel 0
    patchno    110
    intno      20050900
    make:      multithreaded, ASCII, optimized
    pid        2344
    gateway runs with dp version 229(ext=109) (@(#) DPLIB-INT-VERSION-229)
    gw/local_addr : 0.0.0.0
    CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
    CCMS: Initalizing shared memory of size 40000000 for monitoring segment.
    Bind service sapgw01 (socket) to port 3301
    GwPrintMyHostAddr: my host addresses are :
      1 : [172.20.28.159] MTW02SDEC01.mindsap.com (HOSTNAME)
      2 : [127.0.0.1] MTW02SDEC01.mindsap.com (LOCALHOST)
    DpSysAdmExtCreate: ABAP is active
    DpSysAdmExtCreate: VMC (JAVA VM in WP) is not active
    DpShMCreate: sizeof(wp_adm)          19976     (908)
    DpShMCreate: sizeof(tm_adm)          3605136     (17936)
    DpShMCreate: sizeof(wp_ca_adm)          18000     (60)
    DpShMCreate: sizeof(appc_ca_adm)     6000     (60)
    DpCommTableSize: max/headSize/ftSize/tableSize=500/8/528040/528048
    DpShMCreate: sizeof(comm_adm)          528048     (1048)
    DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0
    DpShMCreate: sizeof(slock_adm)          0     (96)
    DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
    DpShMCreate: sizeof(file_adm)          0     (72)
    DpShMCreate: sizeof(vmc_adm)          0     (1296)
    DpShMCreate: sizeof(wall_adm)          (22440/34344/56/100)
    DpShMCreate: sizeof(gw_adm)     48
    DpShMCreate: SHM_DP_ADM_KEY          (addr: 06110040, size: 4241064)
    DpShMCreate: allocated sys_adm at 06110040
    DpShMCreate: allocated wp_adm at 06111B30
    DpShMCreate: allocated tm_adm_list at 06116938
    DpShMCreate: allocated tm_adm at 06116968
    DpShMCreate: allocated appc_ca_adm at 0648B248
    DpShMCreate: allocated comm_adm at 0648C9B8
    DpShMCreate: system runs without slock table
    DpShMCreate: system runs without file table
    DpShMCreate: allocated vmc_adm_list at 0650D868
    DpShMCreate: allocated gw_adm at 0650D8A8
    DpShMCreate: system runs without vmc_adm
    DpShMCreate: allocated ca_info at 0650D8D8
    MtxInit: -2 0 0
    Mon Feb 18 16:09:14 2008
    GwDpInit: attached to gw_adm at 0650D8A8
    Thanks,
    Vadi

    Dear All,
    The issue has been resolved by changing the DDIC password to what it was when we have started the upgrade.The password was "welcome" when we have started with upgrade after that it has been changed to
    "basis05" during upgrade.we changed it back to welcome and it started working fine.
    Here it took long time to find out what was the password when we have starte upgrade.Resetting to standard ddic password also ddint help out in our case.
    Thanks for all your replies.

  • SCM5 - SCM7 Upgrade Error during LiveCache upgrade Step C4

    We are in the process of upgrading our SCM5 system to SCM7 release level. During livecache upgrade step C4 to load transaction data, we are getting error CONNE_IMPORT_WRONG_COMP_TYPE. The dump says that "when importing the object 'OT_ORDERS", the component no. 5 in the dataset has a different type from the corresponding component of the target object in the program "/SAPAPO/SAPLOM_UPGR_PARALLEL". The data type is "P" in the dataset, but "C in the program".
    Our source livecache version is 7.6.03.12 and target livecache version we are upgrading to is 7.7.04.29. We used BS 7 SR1 liveCache 7.7.04 DVD from service marketplace. We did not use the update DVD since the guide mentioned that customers on SCM5.1 or higher need to run livecache upgrade from update DVD.
    All steps in A, B have already been completed.
    More details from the ST22 dump -
    Error analysis | | An exception occurred that is explained in detail below. | | The exception, which is assigned to class 'CX_SY_IMPORT_MISMATCH_ERROR', was | | not caught in | | procedure "GET_DB" "(METHOD)", nor was it propagated by a RAISING clause. | | Since the caller of the procedure could not have anticipated that the | | exception would occur, the current program is terminated. | | The reason for the exception is: | | When importing the object "OT_ORDERS", the component no. 5 in the | | dataset has a different type from the corresponding component | | of the target object in the program "/SAPAPO/SAPLOM_UPGR_PARALLEL". | | | | The data type is "P" in the dataset, but "C" in the program. Information on where terminated | | Termination occurred in the ABAP program "/SAPAPO/SAPLOM_UPGR_PARALLEL" - in | | "GET_DB". | | The main program was "SAPMSSY1 ". | | | | In the source code you have the termination point in line 3222 | | of the (Include) program "/SAPAPO/OM_UPG_CLASS_IMPCLUT". | | The termination is caused because exception "CX_SY_IMPORT_MISMATCH_ERROR" | | occurred in | | procedure "GET_DB" "(METHOD)", but it was neither handled locally nor declared | | in the RAISING clause of its signature. | | | | The procedure is in program "/SAPAPO/SAPLOM_UPGR_PARALLEL "; its source code | | begins in line | | 3221 of the (Include program "/SAPAPO/OM_UPG_CLASS_IMPCLUT ".
    We are running AIX5.3 and Oracle 10.2.0.2.0.
    Any help here will be greatly appreciated.

    This is exactly the same with OSS 305147 2010. It will be answered in BC-DB-LCA area.

  • AE Deployment Errors in SDM - Upgrading from 5.1 to 5.2

    Hello-
    I'm in the process of upgrading Access enforcer on a Java standalone system from version 5.1 to 5.2.
    Documentation provides a short list of project files that must be deployed in order - I have successfully deployed all others but am now facing the last require file - AEEAR4WS.ear.
    Errors logs are below - Any advice or insight is greatly appreciated.
    ===========================================================================
    Deployment started Mon Dec 01 16:22:04 EST 2008
    ===========================================================================
    Starting Deployment of AEEAR4WS
    Aborted: development component 'AEEAR4WS'/'sap.com'/'localhost'/'2007.12.08.00.49.25':
    Caught exception during application deployment from SAP J2EE Engine's deploy service:
    java.rmi.RemoteException: Cannot deploy application sap.com/AEEAR4WS.. Reason: Error while reading [default web.xml] while deploying [AESelectSystemService_5_2/Config1] web application.; nested exception is:      com.sap.engine.services.deploy.container.DeploymentException: <--Localization failed: ResourceBundle='com.sap.engine.services.deploy.DeployResourceBundle', ID='com.sap.engine.services.servlets_jsp.server.exceptions.WebDeploymentException: Error while reading [default web.xml] while deploying [AESelectSystemService_5_2/Config1] web application.
         at com.sap.engine.services.servlets_jsp.server.container.WebContainerHelper.initXmls(WebContainerHelper.java:570)
         at com.sap.engine.services.servlets_jsp.server.container.WebContainerHelper.deploy(WebContainerHelper.java:143)
         at com.sap.engine.services.servlets_jsp.server.container.DeployAction.deploy(DeployAction.java:140)
         at com.sap.engine.services.servlets_jsp.server.container.WebContainer.deploy(WebContainer.java:104)
         at com.sap.engine.services.deploy.server.application.DeploymentTransaction.makeComponents(DeploymentTransaction.java:606)
         at com.sap.engine.services.deploy.server.application.DeployUtilTransaction.commonBegin(DeployUtilTransaction.java:319)
         at com.sap.engine.services.deploy.server.application.DeploymentTransaction.begin(DeploymentTransaction.java:307)
         at com.sap.engine.services.deploy.server.application.ApplicationTransaction.makeAllPhasesOnOneServer(ApplicationTransaction.java:292)
         at com.sap.engine.services.deploy.server.application.ApplicationTransaction.makeAllPhases(ApplicationTransaction.java:326)
         at com.sap.engine.services.deploy.server.DeployServiceImpl.makeGlobalTransaction(DeployServiceImpl.java:3139)
         at com.sap.engine.services.deploy.server.DeployServiceImpl.deploy(DeployServiceImpl.java:539)
         at com.sap.engine.services.deploy.server.DeployServiceImplp4_Skel.dispatch(DeployServiceImplp4_Skel.java:1555)
         at com.sap.engine.services.rmi_p4.DispatchImpl._runInternal(DispatchImpl.java:304)
         at com.sap.engine.services.rmi_p4.DispatchImpl._run(DispatchImpl.java:193)
         at com.sap.engine.services.rmi_p4.server.P4SessionProcessor.request(P4SessionProcessor.java:122)
         at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)
         at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
         at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
         at java.security.AccessController.doPrivileged(Native Method)
         at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:100)
         at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:170)
    Caused by: com.sap.engine.frame.ServiceException: <Localization failed: ResourceBundle='com.sap.engine.frame.KernelResourceBundle', ID='ERROR:java.io.IOException: Access is denied', Arguments: []> : Can't find resource for bundle java.util.PropertyResourceBundle, key ERROR:java.io.IOException: Access is denied
         at com.sap.engine.core.service630.container.PersistentHelper._getPersistentEntryFile(PersistentHelper.java:98)
         at com.sap.engine.core.service630.container.PersistentHelper._getPersistentEntryStream(PersistentHelper.java:44)
         at com.sap.engine.core.service630.container.PersistentHelperWrapper.getPersistentEntryStream(PersistentHelperWrapper.java:20)
         at com.sap.engine.services.servlets_jsp.server.container.WebContainerHelper.initXmls(WebContainerHelper.java:566)
         ... 20 more
    Caused by: java.io.IOException: Access is denied
         at java.io.WinNTFileSystem.createFileExclusively(Native Method)
         at java.io.File.createNewFile(File.java:828)
         at com.sap.engine.core.service630.container.PersistentHelper._getPersistentEntryFile(PersistentHelper.java:55)
         ... 23 more
    ', Arguments: []--> : Can't find resource for bundle java.util.PropertyResourceBundle, key com.sap.engine.services.servlets_jsp.server.exceptions.WebDeploymentException: Error while reading [default web.xml] while deploying [AESelectSystemService_5_2/Config1] web application.
         at com.sap.engine.services.servlets_jsp.server.container.WebContainerHelper.initXmls(WebContainerHelper.java:570)
         at com.sap.engine.services.servlets_jsp.server.container.WebContainerHelper.deploy(WebContainerHelper.java:143)
         at com.sap.engine.services.servlets_jsp.server.container.DeployAction.deploy(DeployAction.java:140)
         at com.sap.engine.services.servlets_jsp.server.container.WebContainer.deploy(WebContainer.java:104)
         at com.sap.engine.services.deploy.server.application.DeploymentTransaction.makeComponents(DeploymentTransaction.java:606)
         at com.sap.engine.services.deploy.server.application.DeployUtilTransaction.commonBegin(DeployUtilTransaction.java:319)
         at com.sap.engine.services.deploy.server.application.DeploymentTransaction.begin(DeploymentTransaction.java:307)
         at com.sap.engine.services.deploy.server.application.ApplicationTransaction.makeAllPhasesOnOneServer(ApplicationTransaction.java:292)
         at com.sap.engine.services.deploy.server.application.ApplicationTransaction.makeAllPhases(ApplicationTransaction.java:326)
         at com.sap.engine.services.deploy.server.DeployServiceImpl.makeGlobalTransaction(DeployServiceImpl.java:3139)
         at com.sap.engine.services.deploy.server.DeployServiceImpl.deploy(DeployServiceImpl.java:539)
         at com.sap.engine.services.deploy.server.DeployServiceImplp4_Skel.dispatch(DeployServiceImplp4_Skel.java:1555)
         at com.sap.engine.services.rmi_p4.DispatchImpl._runInternal(DispatchImpl.java:304)
         at com.sap.engine.services.rmi_p4.DispatchImpl._run(DispatchImpl.java:193)
         at com.sap.engine.services.rmi_p4.server.P4SessionProcessor.request(P4SessionProcessor.java:122)
         at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)
         at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
         at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
         at java.security.AccessController.doPrivileged(Native Method)
         at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:100)
         at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:170)
    Caused by: com.sap.engine.frame.ServiceException: <Localization failed: ResourceBundle='com.sap.engine.frame.KernelResourceBundle', ID='ERROR:java.io.IOException: Access is denied', Arguments: []> : Can't find resource for bundle java.util.PropertyResourceBundle, key ERROR:java.io.IOException: Access is denied
         at com.sap.engine.core.service630.container.PersistentHelper._getPersistentEntryFile(PersistentHelper.java:98)
         at com.sap.engine.core.service630.container.PersistentHelper._getPersistentEntryStream(PersistentHelper.java:44)
         at com.sap.engine.core.service630.container.PersistentHelperWrapper.getPersistentEntryStream(PersistentHelperWrapper.java:20)
         at com.sap.engine.services.servlets_jsp.server.container.WebContainerHelper.initXmls(WebContainerHelper.java:566)
         ... 20 more
    Caused by: java.io.IOException: Access is denied
         at java.io.WinNTFileSystem.createFileExclusively(Native Method)
         at java.io.File.createNewFile(File.java:828)
         at com.sap.engine.core.service630.container.PersistentHelper._getPersistentEntryFile(PersistentHelper.java:55)
         ... 23 more
    (message ID: com.sap.sdm.serverext.servertype.inqmy.extern.EngineApplOnlineDeployerImpl.performAction(DeploymentActionTypes).REMEXC)
    Deployment of AEEAR4WS finished with Error (Duration 31437 ms)

    Hi Christof,
    The VB codes used in the excel sheets are only excel dependent. I don't think Microsoft has any backward compatability issue with 2003 to 2007. Similarly the VB commands from 5.1 is maintained in 7 so you should not face any major issues there too.
    Badrish

  • EM12c displaying Plug-in Error during OMS upgrade

    I'm doing a 2-System Upgrade from EM 10.2.0.5 to 12.1. The current OMS is on AIX 6.1 and the new OMS will be installed on RHEL 6.2. After staging the 12.1.0.1 plugins and agents on the source OMS (12.1.0.2 plugins with BP1 only available for Linux/Windows) and backing up my repository I am unable to upgrade to the new OMS because of error message seen in the screenshot below.
    https://s3.amazonaws.com/griddba/blogs/em12_oms_upgrade_error.png
    The Pre-upgrade Console indicates all agents and targets are upgradeable (green). I used the command ./runInstaller -pluginLocation /u02/orastage/em12c-agents/ to upgrade the agents during the OMS install. The downloaded plug-ins and agents were copied to /u02/orastage/em12c-agents.
    I checked the note EM 12c: Upgrading Enterprise Manager from 11.1.0.1 to 12.1.0.1 Fails with Error: Plugins are not present for installation of the current Management Service [ID 1437063.1] but it's still unclear why I'm getting this error since the plugin version is the same.
    Any ideas?
    Edited by: DBA on Jun 15, 2012 2:44 PM

    The bp1 for Aix will be released soon. You hav 2 options:
    a) you can wait for few more days and then pick the revisied plugins for aix platform and then do the upgrade.
    b) If you dont want to wait then you can run a specific sql to trun off the pre-req cheecks as sysman on the clones or backed up repository. Since this is an external form i donnt want to paste the sql here which will expose the repository table/parameters. Can you drop me an email and i will send you the sql.

  • Error 1015 when upgrading from 3.0 to 3.0.1

    Hello,
    I recently purchased an iPhone and my first time connecting it to iTunes it asked to upgrade from 3.0 to 3.0.1, which I assumed was fairly standard so I let it go.
    However, it made it about 75% through the progress bar on the iPhone display and to the "restoring iPhone firmware" stage in iTunes, then it gave the 1015 error. I have tried it on several computers since then and it happens every time regardless of which computer/OS I use.
    After this every time I turn the iphone on, connect to the computer or not, it displays a USB with an arrow to the iTunes icon, and I have no control. Basically nothing on it works anymore.
    When I searched on google I found a lot of hits for people trying to downgrade/jailbreak, neither of which I was trying to do, I was simply upgrading based on iTunes request.
    Thanks for any help, right now my iPhone is useless to me, and it's really frustrating.
    Thanks,
    Boyd

    I just got this link off Apple Support. It is a KB article that describes issues with that particular error code. Try and see if that solves your problem.
    http://support.apple.com/kb/TS1275

  • Issues during technical upgrade from 4.6c to ecc 6.0

    Hi
    We are doing a technical upgrade from 4.6C to ECC 6.0. Some transactions in QM module when tested in ECC 6.0 test client give a abap termination message (or dump) and certain transactions like qs42,46, qa18, qs34 etc do not get executed (error = no entry foound for......) and similarly in PP-PI module transactions like C203 have similar problems, even though master data does exist. What should I look for?  Can somebody pl. give details on configuration checks and the OSS notes from a functional point of view for a technical upgrade?
    For certain transactions I get the error message - "Central system of distribution SM-P06CLNT430_TRUSTED is unreachable RFC destination SM_P06CLNT430_Trusted does not exist" - what does this mean?
    thanks
    BE

    Hi,
    1. Have you done successfull installation from 4.6C to ECC 6.0 at the time of PrePare ans SAPUP?
    2. Check SP' for QM and PP-PI modules from http://service.sap.com/sp-stacks.
    3. Configure RFC connections correctly, SM_<SID>CLNT<No>_Trusted automatically created, not manually.
    http://service.sap.com/notes --> search for RFC trusted connections for Ecc 6.0
    http://service.sap.com/upgrade.
    Regards,
    Srini Nookala

  • Add-On ST error in Prepare Upgrade from 46D to ECC 6.0

    I have getting Error Add-On ST 2D, and undecided, I don't know what to do, I had installed Solution Manager for 46D and ST 2D, If anybody has this situation, how do I download the Add on
    I will appreciate any help on this matter.
    Thanks
    Jagraj Dhillon

    > Dear,
    >
    > I believe you have the addon component 'SAPKITL02D
    > "SAP Solution Manager - Installation 4.6C (02D) "
    > installed in 4.6C , is that right?
    >
    > Since the ST (Solution Manager) cannot be upgraded
    > from current version
    > to the latest using the R3 upgrade, You need to
    > Deinstall the addon. (with import of SAPKITL029 in
    > SAINT) Please reset prepare as described in the
    > upgrade manual (SAPup reset prepare + empty DIR_PUT)
    > and next import the request SAPKITL029 using SAINT
    > which should take care of the de-installation of ST
    > 02D.
    >
    > I hope this helps.
    >
    > Lucio Rodrigues
    > SAP AGS
    Hello, Lucio.  I am in the same boat, only with R/3 version 4.6C, and ST 0.2C (SAPKITL02Y).  Would the SAPKITL029 work for me as well, or is there another SAINT package designed to remove ST 0.2C?
    SAP support has not been very helpful to this point.  If you have an import which would help with uninstalling the addon, please email it to [email protected], or please let me know where to download it if it is available for download.
    Mike McCrory - BMW Global Data Center America's
    Message was edited by:
            McCrory Michael

  • Error after SPS upgrade from SP10 to SP12

    Hi Friends,
    Recently we have done SOLMAN 7.1 sp upgrade from sp10 to sp12.
    Now I want to perform configuration activities in SOLMAN_SETUP.
    But when I am trying to do SYSTEM PREPARATION, I am facing error in first step(Maintain Users).
    "Error: Number of elements in the collection of node COMPONENT CONTROLLER.1.NAMESPACES violates the carnality".
    Kindly suggest me how to clear this above error and proceed further. Further please let me know as a SOLUTION MANAGER consultant what are the steps I need to perform post SP upgrade. I am not BASIS guy. So please let me know what are the activities which need to be performed by BASIS guy and SOLMAN guy
    Please find the attached screen shot for the error screen.
    Thanks & Regards,
    Solman Starter

    Go the transaction STMS, if a window appears when you start the transaction that's mean it is not configured.
    Only in this case :
    1.     Logon on to client 000  with DDIC.
    2.     Execute transaction SE06
    3.     Select the Database Copy or migration option
    4.     Press the Post-installation Processing button.
    5.     When prompted Do you want to re-install the CTS? Press the Yes button
    6.     When prompted for the Source System of Database Copy?, make sure that the <SID> of the production system is selected.  Press the checkmark button to continue.
    7.     When prompted Change originals from PRD to QUA?, press the Yes button
    8.     When prompted Delete TMS Configuration?, press the Yes button
    9.     When prompted Delete old TMS configuration?, press the Yes button
    10.     When prompted Delete Old Versions of transport routes?, press the No button
    Concerning the initial problem, i found this note :
    http://service.sap.com/sap/support/notes/2025884

  • Issues during technical upgrade from  version 4.6C to ECC 6.0

    Dear All,
    We have done a technical upgrade from version 4.6C to ECC 6.0 and encountered following issues -
    In the t-code ABZE (acquisition with in house production) there is a check-box for reversal posting on screen with version 4.6C. However, this field is missing in ECC 6.0. Why so?
    In the report s_alr_87012327, there is a field "only with creation block" in version 4.6C. However, this field is missing in ECC 6.0. Why so?
    Request to kindly suggest the alternative to carry out the same in ECC 6.0.
    Thanks in advance.
    Regards,
    Dhawal

    Hi Akshya,
    Please find answers below.
    1) 4.6c is NON-UNICODE system, Can I upgrade it into ECC 6.0 UNICODE system?
    Yes you can.
    If you are on a single code page system then you can give a gap between your uprade and unicode conversion. There is no problem with the singlecode upgrade and conversion.
    But if your system is MDMP then you will have to do the CUUC method that is both upgrade and unicode conversion together. Though you can give a gap and sign an disclaimer with SAP it is still not recomended way.
    2) 4.6c does not have any ITS system installed. If we upgrade it to ECC6.0 ABAP only, then Can I activate WAS internal ITS?
    Yes you can activate it.
    3) 4.6c does not have any JAVA stack. When I upgrade it to ECC 6.0, can I upgrade it to dual stack (ABAP+JAVA)? If yes, then how?
    After the upgrade and unicode conversion you can install the java stack.
    Regards,
    Ravi.

  • Error during data transfer from Lotus Notes to SAP via JCO - Urgent Help Required

    Dear SAP Expert:
    I need your help! Recently getting error during data transfer to SAP. I need your suggestion!
    I am transferring Lotus Notes data to SAP via JCO, recently getting the below error msg, could you pls tell me what could be the reason?
    Please suggest me how to fix that kind of issue.
    "com.sap.mw.jco.JCO$Exception: (104) RFC_ERROR_SYSTEM_FAILURE: Error in ABAP/4 statement when processing an internal table. table.
    at com.sap.mw.jco.rfc.MiddlewareRFC$Client.nativeExecute(Native Method)
    at com.sap.mw.jco.rfc.MiddlewareRFC$Client.execute(MiddlewareRFC.java:1244)
    at com.sap.mw.jco.JCO$Client.execute(JCO.java:3842)
    at com.sap.mw.jco.JCO$Client.execute(JCO.java:3287)
    at SAPAdapter.execute(Unknown Source)
    at JavaAgent.fillBapiAndWriteBackToNotes(Unknown Source)
    at JavaAgent.NotesMain(Unknown Source)
    at lotus.domino.AgentBase.runNotes(Unknown Source)
    at lotus.domino.NotesThread.run(NotesThread.java:249)
    Thanks in advance! Your help would be highly appreciated! Thanks again!

    error is clear, check your abap code.

  • LDAP synch not supported during OIM upgrade from 9.x to 11g

    Hi Experts,
    Following line is mentioned in OIM upgrade guide for 9.x to 11g (http://docs.oracle.com/cd/E21764_01/upgrade.1111/e10129/upgrade_oim.htm)
    “LDAP Sync is not supported when you upgrade from Oracle Identity Management 9.1 to Oracle Identity Management 11g”
    Please help me in understanding the above line.
    I have a pretty simple setup of OIM (version 9.1.0.2) with AD and Exchange connected. I guess I don't have any impact of above line.
    LDAP synch is required when we integrate oracle identity manager with oracle access manager.
    Please suggest.
    Thanks
    M S

    Yes LDAP Sync has most of the features when you have OIM and OAM integrated with each other. You can go ahead with upgrade if LDAP Sync is not part of your requirement.

  • Error during Proxy Processing from ECC system

    Hi All,
    I had created Webservice  using ABAP in ECC system with Message interface designed in XI system. This Webservice will simply displays employee address when you enter employee id and address type.During my testing of Web service in ECC system via Tcode WSADMIN, I am getting below error
    "An error has occurred. Maybe the request is not accepted by the server: "
    "Error during proxy processing"
    Request
    POST /sap/bc/srt/xip/sap/Z_ADDRESS_01?sap-client=100 HTTP/1.1
    Host: rpmsap3.rapidigm.com:8080
    Content-Type: text/xml
    Connection: close
    authorization: <value is hidden>
    Content-Length: 389
    SOAPAction: ""
    <SOAP-ENV:Envelope xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xs="http://www.w3.org/2001/XMLSchema"><SOAP-ENV:Body><ns1:Request_Message xmlns:ns1='http://sap2webservice'><Employee_Id>MM01</Employee_Id><Address_Type>AM</Address_Type><Date>11/11/2006</Date></ns1:Request_Message></SOAP-ENV:Body></SOAP-ENV:Envelope>
    Response
    <SOAP-ENV:Envelope xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xs="http://www.w3.org/2001/XMLSchema"><SOAP-ENV:Body><ns1:Request_Message xmlns:ns1='http://sap2webservice'><Employee_Id>MM01</Employee_Id><Address_Type>AM</Address_Type><Date>11/11/2006</Date></ns1:Request_Message></SOAP-ENV:Body></SOAP-ENV:Envelope> HTTP/1.1 500 Internal Server Error
    set-cookie: sap-usercontext=sap-client=100; path=/
    content-type: text/xml; charset=utf-8
    content-length: 270
    sap-srt_id: 20061111/154215/v1.00_final_6.40/A901A40749EEA74BB8D8AB72B56C02A7
    server: SAP Web Application Server (1.0;640)
    <soap-env:Envelope xmlns:soap-env="http://schemas.xmlsoap.org/soap/envelope/"><soap-env:Body><soap-env:Fault><faultcode>soap-env:Server</faultcode><faultstring xml:lang="en">Error during proxy processing</faultstring></soap-env:Fault></soap-env:Body></soap-env:Envelope>
    Appreciate any help on above issue
    Regards
    Manish Mundra

    Hi All,
    Please help on below issue.
    Thanks in Advance
    Regards
    Manish

Maybe you are looking for

  • Dead Ipod photo

    Hello, Since last few days my Ipod Photo is dead. It does not start. Earlier I connected to my Macbook and it started so I formatted and now it does not. When i connect to AC adapter, it still showing "connect to ac supply" icon. I think it is not ab

  • New release desktop software sync problem

    Having downloaded the new deskup software, and made sure that it notifies me of any conflcts in sync-ing the blackberry and Outlook 2003, it now tries to delete anything new added to Outlook that it is not yet on the blackberry. It notifies me of all

  • Which program would export a swf with embedded mp3?

    And not export with it in a Resource folder, as i need to upload one file with music embedded within? I am currently exporting from INDD but the interactive mp3 is exported in a seperate resource folder, and I wish to upload the SWF to a website home

  • I have 2 phones sharing the same i cloud account. Can i delete the account on one phone and set up a separate account. ?

    I have 2 phones sharing the same i cloud account. Can i delete the account on one of the phones and set up a separate account, will this stop the contacts being shared ?

  • Xperia Z1 mic issue (low volume) when using WeChat

    Was searching this forum for a solution, but to no avail. Using Wechat on Xperia Z1 with Android 5 is impossible because mic records at very low volume and other parties strugle to hear me. Microphone suppresion and voice enhancement are turned off,