Error (Err 02) in Canon 7D Mark II when doing image copy from SD to Flash card; is this a bug?

Using hardware and firmware as:- Camera: Canon 7D Mark II firmware ver. 1.0.4.- Flash card (1): Kingston 64 GB ultimate 266X- SD card (2): SanDisk 32 GB Extreme 60 MB/s Both cards where bought from authorized dealer, and looks genuine. Steps to generate the error:1: Test SD card (2) on PC with H2testw with no problems2: Format Flash card (1) in camera3: Format SD card (2) in camera, using low level format4: Take 1505 JPG images in high resolution to the SD card (2)5: Copy images from SD card (2) to Flash card (1) After copying of about 200 images, this resulted in error "Err 02", which cays:"Card2 cannot be accessed. Reinsert/change card2 or format card2 with camera." The problem had occurred previously with a Lexar SD card, so the above steps were made in order to reproduce the error and describe the exact steps taken for the error to occur. Are there anybody else that experience the same error ? Does this look like a bug in the Canon 7D Mark II using firmware ver. 1.0.4, or is there a way I can make it work ? Best regardsMortenZdk

Canon 2nd level support contacted me yesterday.
They said that this issue was unknown in their system.
In order to proceed they needed to read out additional error information from the camera, and such read-out is only possible on an authorized service size, since the software for such read-out is not available for users.
Canon where not interested in providing me the software to do the error read-out, so I could send this to them for further investigation in relation to the support case.
I suggested that the support person should request that such software for error read-out is made available for the end user, in order to provide further information in relation to support case, but the support person was not interested in going forward with such an idea.
Canon were not interested in trying to reproduce the problem them self, even through I offered to send them the SD and Flash cards that caused the problem.
So all Canon could do was to tell me to spendt additional time and money sending the camera to a service size, and then having to miss the camera for 14 days during while the service site investigates.
I must admit, that this has left me with a bad experience in relation to buying a relatively expensive Canon camera together with high-end brand memory cards. In my opinion, it looks like Canon is not giving the end user any good ways of determined the reason for an error, which could lead to product improvement for example a firmware fix. All I can do, if I want to move on this this, and potentially help Canon fix their product, is to spend additional time and money sending the camera to a service size.
There is definitely room for improvement!

Similar Messages

When trying to copy from mac HD to WD for mac i get error code -50

when trying to copy from mac HD to WD for mac i get error code -50 Solutions?

OS X errors are cryptic. error code -50 says error in user parameter list.
You need to give us WAY more info if you want help.
What is WD for Mac? If it's an external drive - did you install any software for it? (shouldn't need to)
How much free space on the Mac HD? Size of the file(s)?
Is it a USB drive or Firewire or Thunderbolt?

"Error check activation" is the message I get when pulling a book from the library. My computer is authorized (per the ADE screen) I have tried un-authorrzing and re-authorizing but nothing works. Please help

"Error check activation" is the message I get when pulling a book from the library. My computer is authorized (per the ADE screen) I have tried un-authorrzing and re-authorizing but nothing works. Please help

I am having the same problem, and my computer is authorized through my Adobe ID and I cannot open any books. I tried downloading a book from the university library, using my ID, the book is in ACSM format, and I cannot open the book because it keeps telling me
"error check activation" I am including screen shots to show my computer is authorized.

Canon 5d Mark II and Raw Images in CS4

HI
I have a Canon 5D Mark II and have just upgraded to standard CS4. When I go to view my Raw files on bridge I am unable to do this - all I see instaed of the thumbnail is the CR2 file. When I click on the file it states 'could not complete your request as it is not the correct type of document' - can you please advise how I can view these files?
Thanks

hu38 wrote: I have a Canon 5D Mark II and have just upgraded to standard CS4. When I go to view my Raw files on bridge I am unable to do this - all I see instaed of the thumbnail is the CR2 file. When I click on the file it states 'could not complete your request as it is not the correct type of document' - can you please advise how I can view these files?
The Canon 5D Mark II requires at least version 5.2 of the ACR plug-in. See http://kb2.adobe.com/cps/407/kb407111.html
The CS4 default installed ACR 5.0 so you have to upgrade the plug-in.
Get version 5.6 here: http://www.adobe.com/downloads/updates/

Upgraded Adobe LR 4.1, CS6 Beta & got the Canon 5D Mark III, WHEN is next dot release Camera Raw?

I Purchased the Upgraded Adobe LR 4.1, CS6 Beta & got the Canon 5D Mark III, Mac Pro server update to Lion, WHEN is next dot release Camera Raw? My workflow has trippled in time because of this issue. I'm so frustrated with having to convert images in a slowed up piece of crap canon software package and then wait another decade for the newest LR to load the images I could crap fire! Come on Adobe, where's the release? After a few grand you'd think we'd get a better response time. As for Canon, they are not consistant with community software sharing and can kiss my *!! because to leave Adobe hanging sux!
There should be new laws that penalize jerks that screw with workflow!
Time is money, let's go Adobe!

"so there are no Adobe staff here to see your rant."
Oh, they're here and they see it...
BTW this might help?

Error using jar, but the programme works right when i run it from any IDE

I have a programme with 25 .java archives. Is a GUI with a main panel and a JToolBar. When i run ir from Eclipse iDE, NetBeans or in the Linux shell it works rigth. Then i try to make a .jar. In the process i haven't any error, and when the application starts either. But when i click in some of the JMenuItems, they don't work. The function of this Items are change the main panel. It's like some .class of event listeners aren't included, but i check the .jar and has the same .class archives than the compiled project.
What can be problem?? It's very urgent, please.
Regards

I'm so sorry for annoying you, i'm a poor stupid
student that don't have money to hire an expert, so i
try to learn and find help everywhere. But, don't
worry, i resolve my problem by myself.what errors are you getting. It would be helpful if you could post the errors or some stack traces that you are getting

The x mark at the right corner of each tab is missing in my ff4.1. I have to right click the tab and then choose the close tab from the drop down? Is this a bug or am i missing something

I am using FF4.1 and the x mark on the right side of each tab is missing
Addons i have installed are
ABP
Download helper
Firebug
Forecast Weather
Ghostery
Live Http Headers
Save as PDF
Test Pilot

I think we can eliminate the graphics card as a suspect (and therefore its driver). I just re-connected my monitor using the internal graphics processor. The Intel 4600. Not fantastic but actually has better features than the card I had hooked up before. (I might as well stay with this for now. It's an HDMI hook up.)
The problem is still there.
This gets more curious all the time. At this point It would seem that the the likelihood of this being a bug is more or less zero, as myself and one other individual are the only ones reporting it.
So, I'm thinking it has to be a flawed install. Maybe some line/lines of code are corrupt, if that can happen while still maintaining the rest of the programs integrity.
Any other thoughts anyone?
Derek.

I receive an error message on HP Pavilion Dv6 when trying to read from an sdhc memory card.

HP Pavilion Dv6 A6y00UA#ABA
Windows 7 64-bit
When I insert the memory card, I am presented with the scan disk message asking to scan and fix the "<memory card name> (D" If I click on "Scan and Fix", select either one check box or both check boxes (doesn't matter) it will scan the card and close out. When I then try to WRITE a folder to the memory card, doesn't matter which card I try, it sits there for a while thinking and then gives an error:
"File Too Large: The file '<%1 NULL:NameDest>' is too large for the destination file system."
If I try to read a photo from a card put there by my camera I get the message:
You need to format the disk in drive D: before using it.
or
Please insert a disk into SDHC (D.
or
any number of random errors.
I've updated the Intel chipset drivers, right clicked and updated the Realtek Card reader drivers using Windows Update.
HELP!!!

This forum is about making podcasts. The best place to ask would be in either the iTunes for Windows or iTunes for Mac forum as appropriate.

BYMONTHDAY is causing the error while opening the ics file in outlook when event is exported from SharePoint Calendar

Hi All,
I am trying to parse the SharePoint recurrence data to get the RRULE for the ics file the RRULE parsed works fine for Yearly and Daily but it causes error when opening the ics file for the Monthly and
weekly recurrence recurrence. I have opened the ics file in the notepad and observed that the BYDAY and BYMONTHDAY causes the problem. If I remove the tag the file opens fine but with wrong recurrence pattern.
Any help will be appreciated.
Regards
Ajeet
Ajeet

Ajeet,
I see that this is an extremely old post, but I thought I would refresh it with a bit more info.
I wish I had found this post a few days ago. I realized the same thing as well. I don't quite understand the reasoning behind requiring the by day date must be the same as the event date. Another thing with rrecurrence is that if
you pick a day of the week for a recurrence (i.e. Friday), then the start date must also occur on a Friday (I am just casting it as the first Friday of the month).
I have come into this same issue with the BYMONTHDAY. I am currently working on trying to configure an .ICS file to allow for multiple monthly recurrences, but it appears Outlook does not support multiple days within an event (determined by trying
to create an even in Outlook and picking the recurrence option). It seems that you are only allowed to have an event on (for example) every Friday of each month, or the (x) day of each month. You cannot set any other occurrences of any other day
within the same ICS file. Hopefully someone else will find this information useful.
Cheers,
Tracy

Error when doing blind transfer from CAD

We have put a button on our CAD desktop with an action to perform a blind transfer to a specific extension (which happens to be a routepoint).
20% of the transfers fail with this error message:
"The agent- or workflow-initiated action request failed."
Any ideas how we can fix this?
Our CAD is version 6.4.2.12, on UCCX Prem. 5 and CUCM 6.1.
Thanks,
Johnny

There's a known bug for this but it's not for blind transfers, might be worth TAC'ing this. I also found a similar bug for v6.0.
CSCsl88916 Bug Details
Supervised Transfer Causes WrapUp Data problem
Symptom:
After Making a supervised transfer, if wrap up data is enabled on the CDA, than agent will get this error message:
"The agent or workflow-initiated action request failed"
Conditions:
This error only happens on Supervised transfer, not blind.
Workaround:
This error only happens when you have enabled this 2 following options on RP and CTI Ports,
Caller Number
Redirected Number
Disable those
Further Problem Description:
The above 2 options are not on by default and many users have them unchecked, but some users modify those parameters and CAD throws that error message
To reproduce this is what can be done:
Enabled the 2 options:
Caller Number
Redirected Number
On the CTI port and Route Point,
call to the RP
Agents Picks Up the Call
Talks to the caller
Hits the transfer button and initiates a call to the NON - ICD extension.
Waits till the called party answers
Hits the transfer button again
If wrap up data option is enabled on the CDA, than
Agent will get this error message:
The agent or workflow-initiated action request failed Status
Product:
Cisco Unified Contact Center Express
Technology:
1st Found-In
5.0(1)
5.0(1)SR1
5.0(1)SR2
Fixed-In
5.0(2.1)
7.0(1)
7.1(1.26)
5.0(2.1.10)
5.0(2.2.20)
Component(s)
icd
Related Bug Information Workflow Initiated failed Exception - Unable to set the wrapup data
Symptom: Work Flow Initiation Exception comes when Agent selects Wrap up data after Transfer is completed Conditions: Agent 1 has an ICD call He click Work button on CAD Now he Transfers the call to another extension from CAD The Agent1 is asked to choose Wrap-up data Once he chooses wrapup data Workflow Initiation exception is thrown
Workaround: None
Please rate useful posts...

Timeout error (Hex 0xBFFF0015) in NI VISA test panel when attempting to read from device

Hello,
I am attempting to control the set position of three daisy chained four-way actuator valves. They are VICI Valco and model # EUHA. I have them connected via RS-232 to USB into my computer. I was able to communicate with them when I sent some simple commands through hyperterminal and when I open MAX the devices appear and the panel says the devices are functioning properly. However, when I go into the test panel and try to run some default commands, I get the timeout error, 0xBFFF0015, when reading the command. Thank you for any help you can provide.
Solved!
Go to Solution.

Okay I'm running it again today and I'm noticing that its displaying results when I attempt to read from the valve but still tells me it timed out. Aside from the timeout error, both hyperterminal and visa are providing comparable results. The two commands I have been trying to read from the valves are AM (to check what mode the actuator is set to) and CP (to check what position the valve is at).

Error Log when doing a Copy data from the Hyperion web Administration tool

Hello, I got an error message below when I was trying to use the copydata Administration tool in Hyperion Web.
" MSG_COPY_DATA_OPTIONS_FAILED: An error occurred while running the specified calc script. Check the log for details."
Could you please let me know the path to find the log so I could find out what was the error about?
Thanks

Hello, found the log...here's the error log
[Thu Aug 19 10:55:14 2010]Local/PLCMPLAN/Main/user name /Info(1013162)
Received Command [Calculate] from user [hyperionprod]
[Thu Aug 19 10:55:15 2010]Local/PLCMPLAN/Main/user name /Error(1200315)
Error parsing formula for [FIX STATEMENT] (line 1): invalid object type
[Thu Aug 19 10:55:15 2010]Local/PLCMPLAN/Main/user name /Error(1012001)
Invalid Calc Script syntax [
This is not the first time I have done this process.. it worked great before... however, I noticed that performance bar is very slow...
If you recommend to restart services which services? The Hyperion Admin services, Provider Services or the Essbase services?
Please advise

Error in Console: "Failed to check-in!" when trying to copy files.

Whenever I try to copy files, I get the "Preparing to copy..." dialog, which never gets beyond the striped bar. At the same time I try to copy a file, in the Console, I get an error of "Failed to check-in!" Also I get a similar reaction when I try to empty the trash, it just hangs at the "Preparing..." dialog with the striped bar.
I have tried restarting, running repair/verify on the permission and disk. Have also tried Disk Warrior with no success. Does anyone have an idea of what's going on?

I reinstalled Snow Leopard and it fixed the problem.

I keep getting error message: chrome://adblockplus/content/utils.js:90 when I load certain sites. How do I fix this issue?

When I "expand threads" on livejournal pages, Firefox freezes and I'm repeatedly sent the error message: chrome://adblockplus/content/utils.js:90 . It doesn't matter if I chose "stop script" or "keep running script", it still keeps freezing.
I've googled the problem, but I couldn't find a solution for it anywhere.

You might want to reinstall Adblock+. I think I had the same problem once and it was just brought on by a very spotty connection that day, but if this is happening frequently for you there may be a bug with your Adblock+

I get an error message "iPhone is already on a call" when making phone calls from Macbook Air. What can I do to fix this problem?

I have followed the instructions exactly according to Apple for making phone calls from my Macbook Air. Im signed in to iCloud on both devices. Im on the same wifi network. Wifi calls is turned off on my iPhone. Any suggestions?

Howdy jcannon130,
Thanks for using the Apple Support Communities.
To troubleshoot this issue where your Mac believes you iPhone is still on a call while trying to make a call from your Mac, please first reset your iPhone, and then verify you have the settings configured correctly on your Mac and iPhone.
Restart or reset your iPhone, iPad, or iPod touch - Apple Support
Get help using Continuity with iOS 8 and OS X Yosemite - Apple Support
Happy Holidays!
Alex H.

Error (Err 02) in Canon 7D Mark II when doing image copy from SD to Flash card; is this a bug?

Similar Messages

Maybe you are looking for