Error ibtsta: (1) set gpib(0), status 0X8100 returned when 0X100 expected

During install of a GPIB-ENET/100 device and the associated NI-488.2 v1.4 software and running the ibtsta utility (to check for proper software install) I recieve multiple errors the first of which is: (1) set gpib(0), status 0X8100 returned when 0X100 expected

To: Steven B.,
I am using "GPIB Getting Started with Your GPIB-ENET/100 and NI-488.2 for HP-UX", guide March 2001 Edition, P/N 322987A-01 to help me with the installation of a GPIB-ENET/100 device on a HP-UX Workstation.
Our System Information:
1. We are using HP-UX 10.2
2. We have a "E154502 24 AWG CMR (UL) VERIFIED CATAGORY 5 PATCH CABLE ALLEN TEL PRODUCTS CSA LL97744 AWM I/II A/B FT4" blue cable connected from a "LINKSYS FAST ETHERNET 10/100 5-PORT NETWORK HUB" port 1 to a "GPIB-ENET/100" device.
We also have a "HITACHI DATA MASTER CATAGORY 5e -- HCM 4PR/24 AWG (UL) TYPE CM c(UL) -- TYPE FT4 -- (UL) -- VERIFIED TO TIA/EIA -- 568 -- B.2 CAT 5e -- 5/02 (A3394) 180738" green cable connected from the network port on our "STANDARD C3600 HP-UX CONTROLLER SERVER" to the "LINKSYS FAST ETHERNET 10/100 5-PORT NETWORK HUB" port 2.
3. We have TCP/IP installed on our UNIX controller.
4. We are using NI-488.2 Version 1.4.
Also:
Upon power up the PWR/RDY LED blinks red/yellow rapidly. After approx. 30-60 seconds later the PWR/RDY LED stays constant.
According to the guide because we are not connected to the network and therefore no DHCP is available, our GPIB-ENET/100 device should automatically go into network configuration mode recognized by the PWR/RDY LED continuing to blink red/yellow rapidly. This however does not happen. We have entered network configuration mode manually by holding down the CFG RESET switch for approx. 3 seconds. After this we run the EthernetConfig utility and we get the following results:
IP ADDRESS/HOSTNAME ETHERNET ADDRESS SERIAL NUMBER MODEL COMMENT
(0) *busy* 00:80:2F:0A:30:6B
When we try to view properties of the device we get the message: No device found.
We also performed the steps per Chapter 2, page 2-1 installing the software and running the instgpib utility. We followed the instructions that appeared and everything seemed to install fine. After we were having trouble above we decided to check the software installation using the ibtsta utility per 5-1 in the "GPIB Getting Started with Your GPIB-ENET/100 and NI-488.2 for HP-UX" guide. We got several errors of which this one shown is the first:
Error: (1) set gpib(0), status 0X8100 returned when 0X100 expected. Error ENEB returned.
Also, I cannot find the UNIX instruction or variable iberr anywhere. Can you tell me how I can find out the value of iberr?
Thank you,
Abel Fernandez
Raytheon EWS

Similar Messages

  • HT204150 Getting error message ("The set of folders cannot be opened") when clicking on "iCloud' folder in Outlook 2007. Lost contacts and calendar in outlook 2007 while installing icloud.

    Vista + Outlook 2007 + Icloud : Lost all contacts and calendar in outlook when installing/Synchronizing iCloud. Both still available on iphone and iCloud.
    How to get them back in Outlook? Understand iCloud erased them and transferred them in an other outlook account. In Outlook 2007, I can see a folder called "iCloud" but get an error message ("The set of folders cannot be opened...") when clicking on it. I suspect all is there, but no access possible. I assume some Outlook settings are uncorrect, but wonder which settings...?

    Well. Working just fine now, since uninstalling and re-installing icloud and syncing.

  • Workflow Error Message: System Account - The Workflow could not set Content Approval Status

    This is the first time I try an approval workflow. I am using a template in MS Word and assigned an approval workflow to it. The approval workflow is only going to one person in this case.
    When I start the work flow the following 3 error messages show up:
    Workflow Error Message: System Account - The Workflow could not set Content Approval Status. Enable content moderation for this list and run the workflow again.
    Workflow Error Message: System Account - The e-mail message cannot be sent. Make sure the e-mail has a valid recipient.
    Workflow Error Message: System Account - The e-mail message cannot be sent. Make sure the outgoing e-mail settings for the server are configured correctly.
    Thank you for your kind guidance.

    Hi,
    For the first error: Did you set Content Approval in the workflow?  If so, see if you have it in the versioning settings of the list settings.
    For the second error: double check your recipient is set up as being valid.  Did you type in the email address or is it referring to a people picker field?  also, make sure that in the workflow for the email that you actually populated it in the
    To: field.
    for the third error: I suspect that either your farm is not configured for email.  Or, this error is a knock on from the second error.  If you get the second error rectified it may clear this error.  If not then double check the email settings
    for your farm.
    Johnathan Lightfoot

  • Troubleshoot-Adapter engine:Error Setting the message status to DLNG failed

    Dear Experts,
    We use SAP RFC- PI-JDBC(MSSQL).  here the Data(message) successfully transfered to mssql table but the status is been set to DLNG failed,  And it finally shown as SYSTEM ERROR.
    QoS required: ExactlyOnce ,  here The Message has got inserted in that particular table and in PI adapter the  status turned to  DLNG faild and the service again tries to send the same message which is not possible becoz the data is set for primary value.
    2010-09-15 09:59:48 Success Message successfully received by messaging system. Profile: XI URL: http://XXXXX:50000/MessagingSystem/receive/AFW/XI Credential (User): YYYY
    2010-09-15 09:59:48 Success Using connection JDBC_http://sap.com/xi/XI/System. Trying to put the message into the receive queue.
    2010-09-15 09:59:48 Success Message successfully put into the queue.
    2010-09-15 09:59:48 Success The message was successfully retrieved from the receive queue.
    2010-09-15 09:59:48 Error Setting the message status to TBDL failed, due to: com.sap.aii.af.ra.ms.api.DeliveryException: Error updating status..
    2010-09-15 09:59:48 Success Delivering to channel: CCR_JDBC_ZZZZZ
    2010-09-15 09:59:48 Success MP: Entering module processor
    2010-09-15 09:59:48 Success MP: Processing local module localejbs/CallSapAdapter
    2010-09-15 09:59:48 Success Receiver JDBC adapter: processing started; QoS required: ExactlyOnce
    2010-09-15 09:59:48 Success JDBC adapter receiver channel CCR_JDBC_ZZZZZ : processing started; party  , service BS_BCP_IMPLOG_ZZZZZ 
    2010-09-15 09:59:49 Success Database request processed successfully
    2010-09-15 09:59:49 Success MP: Leaving module processor
    2010-09-15 09:59:49 Success The message was successfully delivered to the application using connection JDBC_http://sap.com/xi/XI/System.
    2010-09-15 09:59:49 Error Setting the message status to DLNG failed, due to: com.sap.aii.af.ra.ms.api.DeliveryException: Error updating status..
    2010-09-15 10:37:01 Success The message was successfully retrieved from the receive queue.
    2010-09-15 10:37:01 Success The message status set to DLNG.
    2010-09-15 10:37:01 Success Delivering to channel: CCR_JDBC_ZZZZZ
    2010-09-15 10:37:01 Success MP: Entering module processor
    2010-09-15 10:37:01 Success MP: Processing local module localejbs/CallSapAdapter
    2010-09-15 10:37:01 Success Receiver JDBC adapter: processing started; QoS required: ExactlyOnce
    2010-09-15 10:37:01 Success JDBC adapter receiver channel CCR_JDBC_ZZZZZ : processing started; party  , service BS_BCP_IMPLOG_ZZZZZ
    2010-09-15 10:37:01 Error Unable to execute statement for table or stored procedure. 'imp_log' (Structure 'STATEMENT') due to com.microsoft.sqlserver.jdbc.SQLServerException: Violation of PRIMARY KEY constraint 'PK_XXX_log'. Cannot insert duplicate key in object 'dbo.XXX_log'.
    2010-09-15 10:37:01 Error JDBC message processing failed; reason Error processing request in sax parser: Error when executing statement for table/stored proc. 'imp_log' (structure 'STATEMENT'): com.microsoft.sqlserver.jdbc.SQLServerException: Violation of PRIMARY KEY constraint 'PK_XXX_log'. Cannot insert duplicate key in object 'dbo.XXX_log'.
    Thanks in advance for your valuable answer.

    Hi Vinaygam,
    2010-09-15 10:37:01 Error Unable to execute statement for table or stored procedure. 'imp_log' (Structure 'STATEMENT') due to com.microsoft.sqlserver.jdbc.SQLServerException: Violation of PRIMARY KEY constraint 'PK_XXX_log'. Cannot insert duplicate key in object 'dbo.XXX_log'.
    2010-09-15 10:37:01 Error JDBC message processing failed; reason Error processing request in sax parser: Error when executing statement for table/stored proc. 'imp_log' (structure 'STATEMENT'): com.microsoft.sqlserver.jdbc.SQLServerException: Violation of PRIMARY KEY constraint 'PK_XXX_log'. Cannot insert duplicate key in object 'dbo.XXX_log'.
    See above error, It cannot the Duplicate Key in your log table. Duplicate means repeated as a same data.So kindly check once your data.
    IF,I assume your scenario is Synchronous, If you are using any sender JDBC adapter  just check with your Quality of Service and set it to "Exactly once".
    so kindly do it.
    Thank you,
    Sateesh
    Edited by: sateesh kumar .N on Sep 17, 2010 8:17 AM

  • Error while releasing the Marketing Campaign Status

    Hi Experts,
    I have created a Campaign in CRM 7.0 and when i am trying to set its New Status to "Release"  (in edit mode) from the current status "Created" ,  the browser is directing me to an error page  "400 Bad HTTP request "..
    Can some one suggest me what might be the problem ?
    Thanks,
    Dan

    No answers actually.

  • Set sign-in status toggles to disabled on its own?

    Hello! I have a user whos "Set sign-in status" in OWA keeps toggling to disabled on a daily basis.
    MS support says this is managed by the AD settings for the user. I've checked ever setting and compared them to users who are not experiencing the issue. Does anyone know
    what attribute controls this setting?
    Thank you!

    Hi Chris,
    I want to double confirm the Exchange server version.
    If you are using Office 365, I find this KB for your reference:
    "It looks like your account has been blocked" error when a user tries to sign in to Office 365
    https://support2.microsoft.com/kb/2742372?wa=wsignin1.0
    Since Exchange Online is different from Exchange On-Premises, I suggest ask Exchange Online Froum for help so that you can get more professional suggestions, if you are using Exchange Online. For your convenience:
    http://social.technet.microsoft.com/Forums/msonline/en-US/home?forum=onlineservicesexchange
    Thanks
    Mavis Huang
    TechNet Community Support

  • SP2010 Designer workflow "Set Content Approval Status" does not work

    Hello
    I'm having a problem with a workflow for one of my clients.It is a SharePoint 2010 environment and I can only use SharePoint 2010 designer (no visual studio).
    We have an approval workflow in place, which works great. After the document approval workflow has does its thing, a new workflow can be launged by specific users (they have writing rights and can approve content). The workflow is used to set the release
    date of the document. This can only be determined after content approval.
    However, when the release date is set, the document approval status is changed to concept. This is of course to be expected, as we changed to document metadata. That is why I wanted to add the action "Set content approval" to this workflow. I cannot
    seem to get this action to work. Right now the workflow does the following:
    check out the document (check out is obligatory in our library)
    set the release date field to the released date parameter (defined when starting the workflow)
    check in the document
    set content approval to approved.
    The release date gets set to the parameter value, but the document is not checked in and the content approval status is not set. SharePoint produces the following error message (translated from Dutch): "An error occured. Cannot edit the item, possibly
    because one or more columns require another type of content. Unknown error."
    Guided by other posts online I gathered that this might be because the actions checkin and set content approval occur to close together. I tried letting the workflow pause for the duration of 1 minute after checking in, but this pauses the workflow indefinitely.
    I then tried 5 minutes (as this is the time standard set by SP2010 designer) but this also resulted in indefinite pausing.
    Posts online lead me to believe that I'm not the only suffering from this problem, but as of yet, I haven't been able to find a solution that works for me. Hopefully someone can help me.

    Hi,
    According to your post, my understanding is that the "Set Content Approval Status" didn’t work in SharePoint 2010 Designer workflow.
    I try to reproduce the issue and the result is the same as yours.
    If I only check out and check in the item, the workflow works well.
    However, once I set Content Approval Status after checking in the item, the workflow get error.
    As a workaround, I recommend to use two workflow to achieve what you want.
    First, create the first workflow, and allow the workflow to be manually started.
    Then, create the second workflow, and
    start the workflow automatically when an item is changed.
    When you start the first workflow, the document will be set value of the release date. And then the second workflow will be started automatically to set the content approval status.
    Thank you for your understanding.
    Best Regards,
    Linda Li
    Linda Li
    TechNet Community Support

  • HTTP status code returned by site-wide error handler is 200 OK?

    I'm using a developer install of ColdFusion 11. I set up the following page at http://localhost:8500/test/index.cfm:
    <cfthrow type="application" message="This is an error">
    When I visit that page, the HTTP status code returned is 500, as expected.
    I then created the following page at http://localhost:8500/error.cfm:
    <p>Sorry! That was an error.</p>
    If I set the site-wide error handler in the CF Admin to /error.cfm and visit /test/index.cfm, the HTTP status code returned is 200 OK.
    This seems weird to me. It looks like I can include the following in the error.cfm file to send an error code instead:
    <cfheader statuscode="500" statustext="Server Error">
    Does anyone see that as problematic? Is there a reason why the site-wide error handler should return 200 OK?

    Error Codes are the responsibility of the developer, to define and broadcast. Ultimately, the ColdFusion server has acted appropriately and fulfilled the request (hence the 202). Only the code would know what error was truly thrown, and how to appropriately handle that message to the user, hence the need for you to change the header in the response, if you want that broadcast to the browser in anything of than a "successful request" type of status.

  • Error in Demo-Appl. 'Project Status'

    Reporting an error:
    Project Status Demo. When I try to add a new task to a project, I get:
    ORA-06502: PL/SQL: numeric or value error: character string buffer too small ORA-06512: at "CBOURBOU.PROJSTAT_TASKS_BIU", line 4 ORA-04088: error during execution of trigger 'CBOURBOU.PROJSTAT_TASKS_BIU'
    Regards
    Tino

    i'm pretty sure that the cause of your error is that your userid is longer than 30 characters when you're logged in and trying to create a new task. all the projstat_tasks_biu trigger does is set the last_update_user, last_update_date, and task_id values for projstat_task table. last_update_user is defined in that projstat_tasks table as a varchar2(30), so you'll get that error for sure with a long userid when the trigger does a ":new.last_update_user := v('USER');". try either modifying your table or creating tasks while logged in with a shorter userid and let us know if you still have issues.
    regards,
    raj

  • URGENT - SET TASK (SYSTEM STATUS) TO COMPLETE - IW22

    Hi,
    Can anybody suggest a FM and its parameters (necessary) to set the system status of a task in IW22 transaction?
    I tried using STATUS_CHANGE_INTERN by calling it in my report with OBJNR and STAT. it didn't gimme any error but the status didn't get reflected in IW22.
    All quick inputs in this regard will be highly valuable and appreciated.
    Thanks in Advance,
    Bharathi.

    Hi.
    After calling FM STATUS_CHANGE_INTERN need run some procedure:
    CALL FUNCTION 'STATUS_UPDATE_ON_COMMIT'.
    COMMIT WORK.
    Good luck.

  • Error "The request failed with HTTP status 401: Unauthorized"

    Dear All,
    While running ssrs report using reportviewer I am getting following error as "The request failed with HTTP status 401: Unauthorized". I have also added required entry in registry and rebooted the server. But same issue appears. So, please help
    me to resolve this.
    Thanks in advance

    Hi dsddsadsa,
    According to your description, when trying to running report from the report viewer control, the error  "The request failed with HTTP status 401: Unauthorized" is thrown out.
    While running report viewer control without impersonation setting, by default it will use the process identity which is Network Service (the AppPool identity is Network Service). Depending on the identity of the AppPool the app is running under, the identity
    might be rejected. In your scenario, you may haven’t enable ASP.NET impersonation, you will get this exception. Please set up the following impersonation in the Web.config file, so that ASP.NET will use the configured user name and password to access the report
    server:
    <configuration>
    <system.web>
    <identity impersonate="true"
    userName="domain\user"
    password="password" />
    Reference:
    Request failed with HTTP status 401: Unauthorized (ReportViewer
    control)
    If you have any question, please feel free to ask.
    Best regards,
    Qiuyun Yu

  • SSRS Report Manager error "Sys.WebForms.PageRequestManagerServerErrorException: An unknown error occurred while processing the request on the server. The status code returned from the server was: 500"

    Hi All,
    I am getting error "Sys.WebForms.PageRequestManagerServerErrorException: An unknown error occurred while processing the request on the server. The status code returned from the server was: 500"
    in one of my Test Environment when trying to run the SSRS 2012 report from report manager.
    Any clue why it is happening.
    Thanks Shiven:) If Answer is Helpful, Please Vote

    Hi All,
    Upon investigation found that there was no space (0 Byte is available) in E drive where underlying SQL DB is residing. 
    Once I cleared the space, report started working and above error was not displaying. 
    Thanks Shiven:) If Answer is Helpful, Please Vote

  • An Error Occurred During Report Processing - Sys.WebForms.PageRequestManagerServerErrorException: An unknown error occurred while processing the request on the server. The status code returned from the server was: 12019

    When I run the report on production I got the following error message:
    Sys.WebForms.PageRequestManagerServerErrorException: An unknown error occurred while processing the
    request on the server. The status code returned from the server was: 12019
    It hasn’t happen on Dev and Test before.                           
    I googled, The error is described as:
    12019 ERROR_INTERNET_INCORRECT_HANDLE_STATE
    The requested operation cannot be carried out because the
    handle supplied is not in the correct state.
    But I cannot find the solution for that. 
    Has it happend to you before? How to solve that?      

    Same behaviour here, Sharepoint 2013 with SSRS in integrated mode
    Error: Sys.WebForms.PageRequestManagerServerErrorException: An unknown error occurred while processing the request on the server. The status
    code returned from the server was: 12019

  • Sys.webforms.page request manager server error exception:An unknown error occured while processing the request on server. The status code returned from the server was:0

    sys.webforms.page request manager server error exception:An unknown error occured while processing the request on server. The status code returned from the server was:0 We got this response(In firebug console) when we try to click on link (after leave webpage for 3 minuts ideal) which is AJAX based. Please reply ASAP because its urgent.

    Hi SP,
    Please check if the following web config appSettins value settings from SSRS server could fix the issue (Note, back up your original web config file before any modification).
    http://stackoverflow.com/questions/10911610/ssrs-webpage-error-status-code-500
    http://srinivasbn.blogspot.in/2013/09/syswebformspagerequestmanagerservererro.html
    http://connect.microsoft.com/SQLServer/feedback/details/782155/ssrs-2012-failed-with-win32-error-0x03e3
    If you have more questions about the SSRS error logs related to this issue, you can post in the SSRS forum for a better assistance with more experts.
    http://social.msdn.microsoft.com/Forums/sqlserver/en-US/home?forum=sqlreportingservices
    Thanks
    We are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • I keep getting an error message that says "The administrator has set policies to prevent this installation" when I try to install iTunes.  I have tried everything on the website.

    I keep getting an error message that says "The administrator has set policies to prevent this installation" when I try to install iTunes.  I have tried everything on the website.  When i try to remove the components of iTunes I get the same message.  How can I download iTunes?

    Let's try something relatively simple. Download and save a copy of the installer to your hard drive (don't run the install on line and don't start the install just yet):
    http://www.apple.com/itunes/download/
    Now right-click on the iTunesSetup.exe (or iTunes64Setup.exe) that you downloaded and select "Run as administrator".
    Does that go through any better for you?

Maybe you are looking for