Error in acquiring waveform from the agilent 54621A oscilloscope .

error 1074003951 occurs when acquiring waveform from the agilent 54621A oscilloscope.
I have installed
agilent 546xx series instrument driver
NI VISA 14.0

The *IDN command is sent and i have chequed the VISA read it returns the correct string .The error still exists i have attached the block program
Attachments:
AGILENT 54621A Acquire Waveform.vi ‏16 KB

Similar Messages

Acquiring a waveform from the input channel

Hi, while I am trying to acquire teh waveform from the input channel,
it is not showing up in Labview "waveform graph", but the same
waveform is seen on the oscilloscope. I am using NI PCI 6052-E DAQ
board.

Greetings Amu,
How have you configured the PCI-6025E? Is it configured for
differential readings or single-ended readings?
By default, the configuration of the device will be differential,
which means that two input channels are used for every input signal.
When configured in differential mode, you need to connect the positive
terminal of the signal to channel X and the negative terminal of the
signal to channel X+8. For reading a differential signal from channel
0, you will connect the positive terminal of the signal to channel 0
(pin 68) and the negative terminal of the signal to channel 8 (pin
34).
I would suggest to use the Measurement and Automation Explorer (MAX)
software to test the signal before going to LabVIEW. Open MAX and go
to the devices and i
nterfaces folder. The PCI-6052E should be located
in this folder. Right-click on the PCI-6052E and select test panels
and you will be able to test the input signal here. You can change
the mode to continuous and set an sampling rate in the test panels as
well.
Once you can view the signal in the test panel of MAX then I would
suggest to move to LabVIEW. Search for the shipping example entitled
'Cont Acq&Chart (buffered) VI' which is a continuous analog input
example. Select the device number, channel number, and scan rate and
run the VI.
For more information on connecting your signals to the PCI-6052E I
would suggest to refer to chapter 4 of the user manual. I've linked
it below for your reference.
NI 6052E User Manual
http://digital.ni.com/manuals.nsf/webAdvsearch/552436964E347DAF86256BDE00670E9B?OpenDocument&vid=niwc&node=132100_US
I hope this helps.
Let me know if you have any additional questions regarding this issue.
Regards,
Todd D.
NI Applications Engineer

How to acquire data from the memory of multimeter

I am a beginner of Labview. I don't know how to acquire data from the memory of multimeter.
I read some examples about DAQ, but it seems not similar to my case. I can't use DAQ in my computer, as I don't have DAQ board.
Could anybody give me some guide? Similar examples would be great.
Solved!
Go to Solution.

Confirm that you have the VISA Run Time Engine on the target machine. If you do not have it installed, you can install the VISA Run Time Engine from ni.com.
Error -1073807346 Using VISA When Running LabVIEW Executable On Target Computer
Message Edited by Mathan on 10-12-2009 07:11 AM

DB Connect Load - "Unknow error while uploading data from the DB Table"

Hi Experts,
We have our BI7 system connected to Oracle DB based third party tool. The loads are performing quite well in DEV environment.
I would like to know, how we transport DB Connect datasources to Quality systems? Any different process to be followed for DB Connect datasources?
At present the connections between BI Quality and the third party quality systems are established. We transported the DataSource from BI DEV system to BI quality system, but on trigerring an infopackage we are not able to perform loads. It prompts - "Unknow error while uploading data from the DB Table".
Also on comparing the DataSources in DEV system and Quality system there are no fields in "Proposal" tab of datasource in Quality system. Also I cannot change or activate Datasource in Quality system as we dont have change access in quality.
Please advice.
Thanks,
Abhijit

Hi,
Sorry for bumping an old thread ....
Did this issue get ever get resolved?
I am facing the same one. The loads work successfully in Dev. The transport for DBConnect DS also moved in successfully.
One strange this is that DB User for dev did not automatically change to db user from quality when I transported the DBConnect datasource. DBCon DS still shows me the DB User from Dev in Quality system
I get "Unknown Error" whenever I trigger the data package.
Advait

Error message, what does this mean: Itunes couldnt connect because an error occured while reading from the devise?!?!?! HELP

I'm trying to connect my iPAD to my desktop but I receive an error: itunes couldnt connect because an error occured while reading from the devise?!?!?! HELP

have you done a update for your itunes this can be the problem that it will not connect to you ipad so update you itunes and then try it again

Getting error Can't read from the source or disk when moving documents from one folder to another folder in the library

Hi,
When we try to move documents from one folder to another folder in the document library using "Open with explorer" getting beloe error.
Can read from the source file or disk.
The user having below permission for the Library as well as site.
Fullcontrol,Limited access--->Given directly
Read,Limited access--->Givin through the all Test grp
Contribute,Limited Access-->given through test members grp
Read,Limited access---> givin through The group grp
Could you please help me anyone....
Thanks

Hi Reddy,
If you are moving files in two libraries in different sites, then the error will occur and it is by design that there are limitations on the DAV move commands that the DAV client is respecting.
https://social.msdn.microsoft.com/Forums/en-US/6245f332-c609-4a7b-8e00-c8b5e46f7759/cant-move-files-using-windows-explorer-cant-read-from-source?forum=sharepointgeneral
If you are moving files in the same library, I recommend you to use Wireshark to reveal the error message and enable IIS
Trace Logging for Failed Requests to examine the IIS log file for troubleshooting.
https://social.msdn.microsoft.com/Forums/en-US/47cd569d-98f2-4cca-b78e-fd178c097285/cant-read-from-the-source-file-or-disk?forum=sharepointgeneralprevious
To narrow down the issue scope, I recommend you to test with another library and see if the copy in explorer can work.
Best regards.
Thanks
Victoria Xia
TechNet Community Support

I just set up my new iMac, and receive error messages when trying to purchase from the iTunes store (error 8003) or update from the App store (error 403 forbidden). THOUGHTS?

I just set up my new iMac, and receive error messages when trying to purchase from the iTunes store (error 8003) or update from the App store (error 403 forbidden). THOUGHTS?

I am not sure what you mean by "Flash Player for steam"; the only Flash Player installers I know is the ActiveX (for Internet Explorer) and the plugin (for other browsers); you can find both at http://helpx.adobe.com/content/help/en/flash-player/kb/installation-problems-flash-player- windows.html#main-pars_header
[topic moved to Flash Player forum]

Error occured while reading from the device

I need help!!! whenever i try to update my iphone to the new 1.1.1 version, i get an error message saying "error occured while reading from the device" the same message comes up when i try to restore it. i havent mod'd my phone in any way. does anyone know whats wrong or how to fix it?

I have the same problem. Was a solution ever given ?

"An error occurred while restoring from the backup.Files can't be restored"

My 4 month old MacBook Pro 15" running 10.6.2 lobotomized itself and I had to have a new HD put in it. I backed up the old one w/ TM on an external HD. I've tried (by the book, and with direct verbal guidance from the Help People at Apple) to restore the system and files but every time it gets to 10.2% in the restoration process and then I get this message: "An error occurred while restoring from the backup. Please restart." and under the frozen progress bar is the chilling line: "Files can't be restored." I've tried restoring from several dates on the TM backup list but it always stops at 10.2% completion. Help!

Hi.
Start by booting from your SL install disc, and selecting Utilities from the menubar, but before going on to +Restore System from Backups,+ instead select +Disk Utility.+
Make +*absolutely certain+* that your internal HD has the GUID *Partition Map Scheme* and the +Mac OS Extended (Journaled)+ Format (unless you're sure it should be +Mac OS Extended (Case-sensitive, journaled).+
Then do a +*Repair Disk+* (not permissions) on your Time Machine drive.
If that succeeds, quit Disk Utility, then continue with the full restore (per #14 in the FAQ).
But if that finds errors it can't fix, it's possible that +Disk Warrior+ can fix them. It's about $100, and is probably a good long-term investment, but there's no guarantee.
If all else fails, go back to Disk Utility and erase your internal HD, then install OSX. When your Mac restarts, use +Setup Assistant+ to transfer your users, apps, settings, and data from your backups (see #19 in the FAQ).
Then download and instal the "combo" update to get back to 10.6.2. Info and download available at: http://support.apple.com/kb/DL959 (or http://support.apple.com/kb/DL1017 for 10.6.3).
Be sure to do a +Repair Permissions+ via Disk Utility afterwards.

Error 1901. Error attempting to read from the source installation database

OS: Windows 7 Enterprise 64-bit
Browsers: IE 9 and Firefox 10
Flash Version 11.7.700.169
I'm logged in as Administrator. I'm trying to install using this:
start "" /wait msiexec /i install_flash_player_11_active_x.msi /qb
and
start "" /wait msiexec /i install_flash_player_11_plugin.msi /qb
Both commands result in:
Error 1901. Error attempting to read from the source installation database: C:\Windows\Installer\3c0cc1.msi
(the file name seems to be random)
echo %errorlevel% returns 1603.
Help.

Not sure how much I can help you with this. Error 1603 usually indicates that the installer cannot proceed because something is in use; search this page for 1603: http://msdn.microsoft.com/en-us/library/windows/desktop/aa372835%28v=vs.85%29.aspx

Error occurred while restoring from the TimeMachine backup

I have an brand new HD that I want to restore from TimeMachine.
Erased and partitioned this brand new drive. Created 2 partitions and formatted as “OS Extended Journaled/ GUID.”
Did a “Command R recovery boot” and went through the steps to backup from TM to my new HD.
         15 seconds into the restoration process Msg. reads:
“Error occurred while restoring from the backup.
Restart your computer and then try restoring again.”
Trouble shooting:
Luckily my original files and initial boot drive that TM was backing up from remains fine and I performed some more TM back ups as well as a TM backup onto another drive as well.
I even tried restoring to another empty drive with older backups and backups off of another HD and got the same error message.
All my BU’s and BU attempts have been within 10.7.3 on the same MP.
Thank you in advance for any help!!

These are the four hard drives I am using for troubleshooting:
1. Internal new 1TB drive
2. External erased and reformatted 500GB firewire drive
3. Internal original 500GB drive designated for TimeMachine with
~200Gigs of successful backup (Including entire bootdrive)
4. External erased and reformatted 300GB drive that I told
TimeMachine to back up to for testing purposes.
I have only erased and reformatted the first 2 empty drives to use as a future boot drive once I can finally restore from my TimeMachine files to one of them successfully.
My troubles all started when I couldn’t get my cpu to boot from my initial boot drive. That’s what has put me on this track. I have since repaired that boot drive with DiskWarrior to perfect order.
Through a lot of my trouble shooting, I have left that initial boot drive in but have since taken it out. I don’t have lion installed on any other drive. Again, my 2 test drives are empty.
I don’t know how long this old boot drive will remain in perfect order and am glad I have found that I cant use TimeMachine on this side of needing it desperately.
Pondini- Thank you again for hangin' in there with me. I think I understand your last recommendation:
         Do I load a new copy of Lion from this location?:
http://itunes.apple.com/us/app/os-x-lion/id444303913?mt=12&ls=1
The suggestion of “coping the installer” is to have a hard copy like I used to in SnowLeopard etc. for a faster future install?

I am trying to sync iphone 5 to itunes but it says "iTunes could not connect to the iphone as an error occured while reading from the device " and the iphone is not seen on itunes........

i am trying to sync iphone 5 to itunes but it says "iTunes could not connect to the iphone as an error occured while reading from the device " and the iphone is not seen on itunes........

First thing to try is to reset your device. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider should one appear until the Apple logo appears. Let go of the buttons and let the device restart. And then reboot your computer.
See if that fixes your problem.

Error occurred moving data from the transformation RECON_SEQ_GEN: to the transformation FILTRANS.

Hi,
Today one my task in the DAC Etl failed and when I opened the DAC log file of it. I saw the error description as below
Error while contacting Informatica server for getting workflow status for PLP_SRC_WH_AP_Invoice_Reconciliation
Error Code = 36331:Unknown reason for error code 36331
Since there is no much information in DAC log file about the failure, I opened the PLP_SRC_WH_AP_Invoice_Reconciliation session log file.
The error description in the session log file says.
There is an error in the port [NEXTVAL]: The default value for the port is set to: ERROR(<<Expression Error>> [ERROR]: transformation error
... nl:ERROR(u:'transformation error')).
2014-01-14 08:00:45 : ERROR : (582188 | TRANSF_1_1_1) : (IS | Oracle_BI_DW_Server) : node01_ : TT_11023 : An error occurred converting data in the port [NEXTVAL]. The row was dropped.
2014-01-14 08:00:45 : ERROR : (582188 | TRANSF_1_1_1) : (IS | Oracle_BI_DW_Server) : node01_ : TT_11021 : An error occurred moving data from the transformation RECON_SEQ_GEN: to the transformation FILTRANS.
2014-01-14 08:00:45 : ERROR : (582188 | TRANSF_1_1_1) : (IS | Oracle_BI_DW_Server) : node01 : CMN_1086 : RECON_SEQ_GEN: Number of errors exceeded threshold [1].
2014-01-14 08:00:45 : INFO : (582188 | TRANSF_1_1_1) : (IS | Oracle_BI_DW_Server) : node01_ : CMN_1053 : : Rowdata: ( RowType=-4(error but dropped due to abort) Src Rowid=1186281 Targ Rowid=1186281
NEXTVAL (ROW_WID:Int:): "(NULL)"
I am not sure of this error and I have never seen before. Can any one share some ideas on how to tackle this error and make the task execute successfully.
Many Thanks.

Hi,
fist check weather any special characteristics if not
check in data source under this we have fields tab check the format of a particular field format internal/external/check u choose internal format, if any check routine once
use Semantic Groups in the DTP.
Try it
Thanku
lokeeshM
Edited by: lmedaSAP_BI on Oct 20, 2010 6:44 AM

Acquire waveforms from function generator to oscilloscope

I have a problem. We constructed a virtual function generator and a virtual oscilloscope. It's working well, the oscilloscope is displaying the (almost) correct data. My problem is that the waveform displayed in the oscilloscope vi is always sine, although the selected waveform in the function generator is already different.
I should replace the constant 'zero' with something so that the cases will change in order for my oscilloscope to display different waveforms. Is there a way to acquire the values of the constant enum, for instance, from another vi to this vi?

Yes, you would need to replace the constant with a control. Once you do this, in the main VI you simply do a right click on the subVI's terminal and select Create Control/Constant that but you cannot change it as the subVI runs.

Adobe Media Encoder for CS4 error Could not read from the source

Hello,
I get an error when I try to export from Premiere CS4. It doesn't matter how I export. Seems like an easy fix, but I can't figure it out. Any help is appreciated:
- Source File: C:\DOCUME~1\ARTWHI~1\LOCALS~1\Temp\extra and b roll.prproj
- Output File: E:\Living Accused Movie Transfers\video\Cindy at table.avi
- Preset Used: NTSC DV
- Video:
- Audio:
- Bitrate:
- Encoding Time: 16:10:34
1/21/2009 9:50:25 PM : Encoding Failed
Could not read from the source. Please check if it has moved or been
deleted.
Thank you
Art

When you attempt to encode media with Adobe Media Encoder CS4 on Windows, the following error message appears in the text file (AMEEncodingErrorLog.txt) that opens when you click the error icon: "Encoding Failed. Could not read from the source. Please check if it has moved or been deleted."
If it's that correct, you removed an earlier version of Adobe Premiere Pro or Adobe Creative Suite on the same computer.
Do one or both of the following solutions:
Solution 1: Create a shortcut to the Premiere Pro executable file, rename the shortcut to Premiere, and move the shortcut to C:\Program Files\Common Files\Adobe\dynamiclink.
Close all Adobe applications.
In Windows Explorer, navigate to C:\Program Files\Adobe\Adobe Premiere Pro CS4. (If you installed Premiere Pro CS4 in a location other than the default of C:\Program Files\Adobe, then navigate to your custom installation location.)
Right-click on Adobe Premiere Pro.exe (which might appear without the .exe extension) and choose Create Shortcut.
Rename the newly created shortcut to just Premiere.
Important: The name of the shortcut must be exactly Premiere with no other characters.
Open a second Windows Explorer window, and navigate to C:\Program Files\Common Files\Adobe\dynamiclink.
Move the Premiere shortcut that you created into the dynamiclink folder.
Solution 2: Remove and reinstall all Premiere Pro CS4 components or all Adobe Creative Suite 4 components.
Do one of the following:
Windows XP: Choose Start > Control Panel > Add or Remove Programs.
Windows Vista: Choose Start > Control Panel > Programs and Features.
In the list of installed programs, select Adobe Premiere Pro CS4, Adobe Creative Suite 4 Production Premium, or Adobe Creative Suite 4 Master Collection.
Click Change/Remove (Windows XP) or Uninstall (Windows Vista).
Follow the on-screen instructions to remove all components of Premiere Pro CS4 (including Adobe Encore CS4 and Adobe OnLocation CS4) or to remove all components of your edition of Adobe Creative Suite 4.
Re-install your Adobe software.

Error in acquiring waveform from the agilent 54621A oscillosco​pe .

Similar Messages

Maybe you are looking for

Error in acquiring waveform from the agilent 54621A oscilloscope .