Error in adding host to vCloud Director 5.5.
In our vCloud Director 5.5, we have added vcenter server through which ESXi Host are visible. however while preparing the ESXi host for vCloud Director i.e. installing vcloud agent it stucks in installation and never completes. N/W connectivity is working fine also we did manual uninstallation and reinstalling the vcloud director agent we are getting error message.
Can someone help, where are the logs file getting generated in ESXi Host also how to resolve this issue.
Hi,
Can you please confirm VC and Host Version ? "we did manual uninstallation and reinstalling the vcloud director agent we are getting error message" What is the message saying ? Screenshot would be of great help.
Please ensure that we don't have any running VM's on that host,if VCD fails to place the host in MM,you can manually put the host in MM mode and try preparing.Also keep an eye on below article to check if you are hitting with any such issues.
VMware KB: Setting up a provider in vCloud Director fails with the error: Cannot prepare host
VMware KB: Preparing a host for VMware vCloud Director fails with the error: java.net.UnknownHostException
For log check -- > /opt/vmware/vcloud-director/logs do check for vcloud-container-debug.log,better to 'tail' the log when the host is going through preparation phase
Also do check /var/log/vmkernel.log and hostd logs.
Similar Messages
-
Encounter another error when adding host target in EM 12c
Hi, all
After installing EM 12c successfully, I then tried to add target to the EM, I encountered such error:
Error Message: The Oracle Management Server (OMS) host and port specified via OMS_HOST and EM_UPLOAD_PORT is not available. Pass in a valid hostname and port number for the OMS to successfully deploy the agent.
Exit Code :1
Again I am sure that my host name is reachable and port number it complains is open.
I also opened the SR with oracle support, the SR is 3-6060170341.
I would appreciate if anyone can help and shed some light on this issue.
Regards.
YongAs i mentioned earlier if you need help from Oracle pls open a Service request (SR) with oracle support and upload the following logs:
<OMS_INSTANCE_HOME>/sysman/agentpush/*.*
Share the SR number.
Can you also ping the oms host from agent host and vice-versa?
Do you have any firwall ?
While deploying the agent using Add host wizard, keep the port input field blank and it will pick up the next free port automatically. There is some env setup issue which is causing this in both install types.
Once you log an SR, Oracle support will help you, they will look into your env and find the root cause. Posting small snapshot of failure in forum can’t be debugged further without logs or a web conference.
Edited by: Akanksha on Feb 11, 2013 2:32 PM -
We are getting this error while adding entries to SSO database. Its working in other environments and failing in only environment. Please advice.
error MSB4018: The "BizTalk.BuildGenerator.Tasks.SSO.PopulateApplicationProperty" task fa
iled unexpectedly.\r
: error MSB4018: System.Runtime.InteropServices.COMException (0xC0002A40): The external cre
dentials in the SSO database are more recent.\r
error MSB4018: \r
error MSB4018: at Microsoft.BizTalk.SSOClient.Interop.ISSOConfigStore.SetConfigInfo(St
ring applicationName, String identifier, IPropertyBag properties)\r
error MSB4
018: at BizTalk.BuildGenerator.Tasks.SSO.SSOConfiguration.Write(String appNa
me, String propName, String propValue)\r
error MSB4018: at BizTalk.BuildGenerator.Tasks.SSO.PopulateApplicationProperty.Execute
()\r
error MSB4018: at Microsoft.Build.BackEnd.TaskExecutionHost.Microsoft.Build.BackEnd.IT
askExecutionHost.Execute()\r
error MSB4018: at Microsoft.Build.BackEnd.TaskBuilder.ExecuteInstantiatedTask(ITaskExe
cutionHost taskExecutionHost, TaskLoggingContext taskLoggingContext, TaskHost t
askHost, ItemBucket bucket, TaskExecutionMode howToExecuteTask, Boolean& taskRe
sult)
Thanks, Pavan MCTS-Microsoft Biztalk Windows Server 2010Hi,
This error generally arises when your system datetime is not in sync with the Domain Controller datetime. Try following steps:
1. Check if the Windows Time Service is running on your machine or not. Try restarting this service and then restart host instances. Then run your script.
2. If this does not works, have a look at this
link
Hope this will help.
HTH,
Sumit
Sumit Verma - MCTS BizTalk 2006/2010 - Please indicate "Mark as Answer" or "Mark as Helpful" if this post has answered the question -
Error in adding the deployfile to the archive
Hi,
I am trying to activate a J2EE library but the CBS build fails with the exception:
error in adding the deployfile to the archive (Error adding file to archive. Can't read file: /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/DCs/bouvet.com/UserIntegrityLibrary/_comp/META-INF/sda-dd.xml)
An ideas of what is wrong? Created a new activity which contained sda-dd.xml , but still same problem.
complete CBS log
Development Component Build (2006-03-27 07:02:55)
Component name: UserIntegrityLibrary
Component vendor: bouvet.com
SC compartment: bouvet.com_JAAS_LOGIN_MODULES_1
Configuration: JDI_ZEPJAAS_D
Location: JDI_ZEPJAAS_D
Source code location: http://sapJDI.st.bouvet.no:50300/dtr/ws/ZEPJAAS/bouvet.com_JAAS_LOGIN_MODULES/dev/active/DCs/bouvet.com/UserIntegrityLibrary/_comp/
DC root folder: /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/DCs/bouvet.com/UserIntegrityLibrary/_comp/
DC type: J2EE Server Component
DC subtype: Library
Host: sap06.st.bouvet.no
DC Model check:
[dcmake] All used DCs are available locally
[dcmake] validating dependency to build plugin "sap.com/tc/bi/bp/addLib"
[dcmake] validating dependency to used DC "bouvet.com/UserIntegrityLoginModule"
[dcmake] validating dependency to used DC "sap.com/security_api"
[dcmake] validating dependency to used DC "sap.com/com.sap.security.api.sda"
[dcmake] validating entity reference from public part "defLib" to public part "api" of DC "bouvet.com/UserIntegrityLoginModule"
[dcmake] DC model check OK
Start build plugin:
[dcmake] using build plugin: sap.com/tc/bi/bp/addLib
[dcmake] starting build plugin from : /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/DCs/sap.com/tc/bi/bp/addLib/_comp/gen/default/public/addLib/
Build Plugins Version 6.40.0.111 (AdditionaLibraryPlugin, 630_VAL_REL ) from 04 July 2005 11:31:30
Building development component 'UserIntegrityLibrary', vendor 'bouvet.com', type 'J2EE Server Component', subtype 'Library'
software component 'JAAS_LOGIN_MODULES', vendor 'bouvet.com'.
location 'JDI_ZEPJAAS_D'.
source code location 'http://sapJDI.st.bouvet.no:50300/dtr/ws/ZEPJAAS/bouvet.com_JAAS_LOGIN_MODULES/dev/active/'.
Options:
convert *.xlf to *.properties: yes
include sources for debugging: yes
run JLin tests is available : no
Creating Ant build file..
No 'default' JDK_HOME_PATH defined, will use running VM. Please update your configuration.
Redefining context object 'dc_depend_allDirs' from '[com.sap.tc.buildplugin.util.ComponentDependencies@1570945, com.sap.tc.buildplugin.util.ComponentDependencies@121b59a, com.sap.tc.buildplugin.util.ComponentDependencies@19a37a]' to '[com.sap.tc.buildplugin.util.ComponentDependencies@13bdd36, com.sap.tc.buildplugin.util.ComponentDependencies@1381960, com.sap.tc.buildplugin.util.ComponentDependencies@9fa8f]'
Generating provider.xml
Using velocity macro file: /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/DCs/sap.com/tc/bi/bp/addLib/_comp/gen/default/public/addLib/macros/build.vm
Creating Ant build file /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/DCs/bouvet.com/UserIntegrityLibrary/_comp/gen/default/logs/build.xml
Ant build file created in 0.374 seconds
Starting Ant with build file /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/DCs/bouvet.com/UserIntegrityLibrary/_comp/gen/default/logs/build.xml, target build
Using temporary directory /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/t/4DEAF5E55DDD90D1E9FC40123D749AEB
Ant build started at 2006-03-27 07:02:56 GMT-05:00 (EST)
prepare:
[mkdir] Created dir: /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/DCs/bouvet.com/UserIntegrityLibrary/_comp/gen/default/deploy
build:
[echo] Generating public part defLib [compilation]
[pppacker] Packing compilation public part 'defLib'
[pppacker] Packing entity bouvet.com~UserIntegrityLibrary (SERVER_COMPONENTS)
[pppacker] Packing entity reference UserIntegrityLoginModule (bouvet.com), api
[pppacker] Packed 1 entity and 1 entity reference for compilation public part 'defLib'
[timer] Public part packaging finished in 0.138 seconds
[copy] Copying 1 file to /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/t/4DEAF5E55DDD90D1E9FC40123D749AEB
[echo] creating source code archive
[mkdir] Created dir: /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/DCs/bouvet.com/UserIntegrityLibrary/_comp/gen/default/src/java
[zip] Building zip: /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/DCs/bouvet.com/UserIntegrityLibrary/_comp/gen/default/src/java/src.zip
[echo] Creating bouvet.com~UserIntegrityLibrary.sda
[jarsap] Info: JarSAP version 20041217.1600
[jarsap] Info: JarSAPProcessing version 20050426.1600 / JarSL version 20050426.1600
[jarsap] Property jarsap.info.dir is not set.
[jarsap] Building: /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/DCs/bouvet.com/UserIntegrityLibrary/_comp/gen/default/deploy/bouvet.com~UserIntegrityLibrary.sda with compression
Ant build finished with ERRORS
file:/usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/DCs/bouvet.com/UserIntegrityLibrary/_comp/gen/default/logs/build.xml:69: error in adding the deployfile to the archive (Error adding file to archive. Can't read file: /usr/sap/JDI/JC03/j2ee/cluster/server0/temp/CBS/29/.B/8827/DCs/bouvet.com/UserIntegrityLibrary/_comp/META-INF/sda-dd.xml)
Ant build finished at 2006-03-27 07:02:56 GMT-05:00 (EST), Duration: 0.386 seconds
Build finished with ERROR
Cleaning up.Did a space modification (since the DTR actually check diff for difference before checkin) and activated the new activity.
-
Error while adding principal to a process
Hi All,
I am getting the following error while adding security principal to Task Manager for my process,
Caused by: | [com.adobe.livecycle.usermanager.client.DirectoryManagerServiceClie
nt] errorCode:16385 errorCodeHEX:0x4001 message:Exception wrapped in DSCExceptio
n is Null or NOT An Instance of UMException chainedException:ALC-DSC-012-000: co
m.adobe.idp.dsc.registry.ServiceNotFoundException: Service: DirectoryManagerServ
ice not found.chainedExceptionMessage:Service: DirectoryManagerService not found
. chainedException trace:ALC-DSC-012-000: com.adobe.idp.dsc.registry.ServiceNotF
oundException: Service: DirectoryManagerService not found.
at com.adobe.idp.dsc.registry.service.impl.ServiceRegistryImpl.getServic
e(ServiceRegistryImpl.java:972)
at com.adobe.idp.dsc.registry.service.impl.ServiceRegistryImpl.getHeadAc
tiveConfiguration(ServiceRegistryImpl.java:830)
at com.adobe.idp.dsc.engine.impl.ServiceEngineImpl.resolveConfiguration(
ServiceEngineImpl.java:146)
at com.adobe.idp.dsc.routing.Router.routeRequest(Router.java:58)
at com.adobe.idp.dsc.provider.impl.base.AbstractMessageReceiver.routeMes
sage(AbstractMessageReceiver.java:88)
at com.adobe.idp.dsc.provider.impl.vm.VMMessageDispatcher.doSend(VMMessa
geDispatcher.java:210)
at com.adobe.idp.dsc.provider.impl.base.AbstractMessageDispatcher.send(A
bstractMessageDispatcher.java:57)
at com.adobe.idp.dsc.clientsdk.ServiceClient.invoke(ServiceClient.java:2
08)
at com.adobe.livecycle.usermanager.client.DirectoryManagerServiceClient.
findPrincipals(DirectoryManagerServiceClient.java:835)
at com.adobe.repository.ui.aac.commands.FindPrincipalsCommand.execute(Fi
ndPrincipalsCommand.java:127)
at com.adobe.repository.ui.aac.commands.CommandProcessor.execute(Command
Processor.java:56)
at com.adobe.repository.ui.aac.struts.actions.FindPrincipalsAction.execu
te(FindPrincipalsAction.java:115)
at com.adobe.repository.ui.aac.struts.actions.CommandProcessorAction.exe
Any help is greatly appreciated.
Thanks
RaghuI am using RHEL 5 - 64 bit Linux on 3-Tera Virtual host with Java 5,MySQL and adobe pre-configured Jboss 4.2 to install LiveCycle 8.2 and My intension is to get the Rights Management Service Installed . After configuring the .ear files(using Rights Management alc-lfs not excluded-solution component in the LCM CLI properties file ) and running the Jboss , I get the Jboss Running but with following Error
ERROR [org.jboss.ejb.plugins.LogInterceptor] RuntimeException in method: public abstract java.lang.Object com.adobe.idp.dsc.transaction.impl.ejb.adapter.EjbTransactionBMTAdapterLocal.do RequiresNew(com.adobe.idp.dsc.transaction.TransactionDefinition,com.adobe.idp.ds c.transaction.TransactionCallback) throws com.adobe.idp.dsc.DSCException:
ALC-DSC-000-000: com.adobe.idp.dsc.DSCRuntimeException: Internal error.
at com.adobe.idp.dsc.transaction.impl.ejb.adapter.EjbTransactionBMTAdapterBean.doR equiresNew(EjbTransactionBMTAdapterBean.java:249)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
Caused by: java.lang.NoClassDefFoundError: com/adobe/dctmconnector/config/DctmConnectorConfigBean
at java.lang.Class.getDeclaredConstructors0(Native Method)
at java.lang.Class.privateGetDeclaredConstructors(Class.java:2357)
at java.lang.Class.getConstructor0(Class.java:2671)
at java.lang.Class.newInstance0(Class.java:321)
at java.lang.Class.newInstance(Class.java:303)
at com.adobe.idp.dsc.registry.component.impl.ComponentRegistryImpl$12.doInTransact ion(ComponentRegistryImpl.java:877)
at com.adobe.idp.dsc.transaction.impl.ejb.adapter.EjbTransactionBMTAdapterBean.doR equiresNew(EjbTransactionBMTAdapterBean.java:218)
... 199 more
2009-06-16 10:23:02,554 ERROR [com.adobe.idp.dsc.startup.DSCStartupServlet] DSC Startup failed. Reason: Internal error.
2009-06-16 10:23:02,554 WARN [com.adobe.idp.dsc.startup.DSCStartupServlet] Unable to start the DSCManager
and upon running the deploy liveCycle Component using LCM CLI task
./ConfigurationManagerCLI.sh deployLiveCycleComponets -f cli_propertyFile.txt
I see that few of DSCs (especially the adobe-usermanager-dsc ) were never started by the installer and It stopped throwing Exceptions While trying to deploy adobe-rightsmanagement-jboss-dsc.jar.
Progress: [5%, DSC already installed, but is not started adobe-remotingConnector-dsc.jar]
Progress: [8%, Deploying DSC adobe-usermanager-dsc.jar]
Progress: [8%, DSC already installed, but is not started adobe-usermanager-dsc.jar]
Progress: [11%, Deploying DSC adobe-usermanager-util-dsc.jar]
Progress: [11%, DSC already installed, but is not started adobe-usermanager-util-dsc.jar]
Progress: [14%, Deploying DSC adobe-jobmanager-dsc.jar]
Progress: [14%, DSC already running adobe-jobmanager-dsc.jar]
While LCM CLI tries to install RightsManagement DSC following exceptions are thrown
[2009-06-16 10:47:16,604], INFO, main, com.adobe.livecycle.lcm.feature.deployment.DeployDSCs, DSC not installed. DSC will now be installed: com.adobe.livecycle.RightsManagement /opt/adobe/livecycle8.2/deploy/adobe-rightsmanagement-jboss-dsc.jar
[2009-06-16 10:47:32,227], SEVERE, main, com.adobe.livecycle.lcm.feature.deployment.DeployDSCs, Failed to deploy component /opt/adobe/livecycle8.2/deploy/adobe-rightsmanagement-jboss-dsc.jar.
com.adobe.livecycle.lcm.core.LCMException[ALC-LCM-030-200]: \ to deploy component /opt/adobe/livecycle8.2/deploy/adobe-rightsmanagement-jboss-dsc.jar.
at com.adobe.livecycle.lcm.feature.deployment.DeployDSCs.deployDSCFiles(DeployDSCs .java:396)
at com.adobe.livecycle.lcm.feature.deployment.DeployDSCs.deployDSCs(DeployDSCs.jav a:149)
Caused by: com.adobe.idp.common.errors.exception.IDPSystemException: nullorigin: | [com.adobe.livecycle.usermanager.client.DirectoryManagerServiceClient] errorCode:16385 errorCodeHEX:0x4001 message:Exception wrapped in DSCException is Null or NOT An Instance of UMException chainedException:ALC-DSC-012-000: com.adobe.idp.dsc.registry.ServiceNotFoundException: Service: DirectoryManagerService not found.chainedExceptionMessage:Service: DirectoryManagerService not found. chainedException trace:ALC-DSC-012-000: com.adobe.idp.dsc.registry.ServiceNotFoundException: Service: DirectoryManagerService not found.
I tried to look for adobe-usermanager-dsc in the admin UI but did not find one over there . I even tried copying the adobe-usermanager-dsc.jar to pre-configured Jboss server/all/lib directory but that does'nt makes a difference .
I was suggested to use different combinations of excluded solution components in the cliProperties file
When I used the following list of excludedSolutionComponents I did not see the (ERROR [com.adobe.idp.dsc.startup.DSCStartupServlet] DSC Startup failed. Reason: Internal error.) but still the dobe-usermanager-dsc does not starts and I get the same errors of (com.adobe.idp.dsc.registry.ServiceNotFoundException: Service: DirectoryManagerService not found.) when the LCM CLI reaches installing the Rights Management DSC.
excludedSolutionComponents=ALC-LFS-BusinessActivityMonitoring,ALC-LFS-ConnectorI BMContentManager,ALC-LFS-ContentServices,ALC-LFS-PDFGenerator,ALC-LFS-ProcessMan agement
#,ALC-LFS-RightsManagement,ALC-LFS-BarcodedForms,ALC-LFS-DigitalSignatures,ALC-L FS-Forms,ALC-LFS-Output,ALC-LFS-PDFGenerator3D,ALC-LFS-ReaderExtensions,ALC-LFS- ConnectorEMCDocumentum,ALC-LFS-ConnectorIBMFileNet
Any help on this issue will be highly obliged.
Thank you.
Mohammad -
Network Error []: Cannot Get Host Name when running business rules
Guru's
We are getting the following error intermittently when we are running business rules (Planning Application >>Tools>>Business Rules) or running SmartView refreshes:
Network error []: Cannot Get Host Name
The following is then logged in the Essbase Application logs:
Local/Application/Database/admin@Native Directory/Error(1042022)
Network error []: Cannot Get Host Name.
A quick look at the Essbase Error Messages Doc says it is a network error and we have to consult the network documentation. Unfortunately this is not very descriptive so we logged an SR with Oracle but we don't seem to be getting a resolution.
The environment is 11.1.2.0 and the architecture is as follows:
Server 1 - MS Server 2008 x64:
Planning, Calc Manager, Foundation Services, Framework Web Services, EAS, APS, Web Analysis, FR Web Services
Server 2 - MS Server 2008 x64:
Essbase Server
Server 3 - MS Server 2008 x64:
Framework Services, FR Print Services
We have tried doing the following:
1. Put in the server host names into the hosts file on the Hyperion Servers
2. Applied the following TCP/IP settings on all the Hyperion Servers and one of the user machines as a test:
- Added a new DWORD Value named TcpTimedWaitDelay and set it to 30.
- Added a new DWORD Value named MaxUserPort and set it to 65534.
- Added a new DWORD Value named MaxFreeTcbs and set it to 6250
3. Confirmed that there are no packet drops by monitoring the server NICs so no packet loss could be the cause of this issue
4. The Essbase Config file has the following settings:
NETDELAY 2000
NETRETRYCOUNT 2500
Has anyone come across this issue and if you managed to resolve it, how did you go about it.
ThanxHi Rahul
The issue is happening to a number of calcs so it it not one calc specifically. I will ask the functional consultants to enhance the logging in the business rules so that we can see if the issue happens on a specific member\block etc and yes we do use Xrefs
We can run this as a calc in EAS without any issues and it's intermittent because this business rule runs 95% of the time in Planning Application >> Tools >>Business Rules without any issues.
Thanks -
Error in Adding new vritual machine server to HaA cluster ???
Hi
when i adding new Server to my cluster i see this error
Check prerequisites to add server (192.168.20.253) to server pool (karkas) succeed
2009-11-29 12:16:33 Check prerequisites to add server (192.168.20.253) to server pool (karkas) succeed
2009-11-29 12:16:46 During adding servers ([192.168.20.253]) to server pool (karkas), Cluster setup failed: (OVM-1011 OVM Manager communication with 192.168.20.254 for operation HA Setup for Oracle VM Agent 2.2.0 failed: errcode=50006, errmsg=Do 'clusterm_init_root_sr' on servers ('192.168.20.253') failed. )
but when edited again see solved problem but not HA feature work correctly(when shutdown server pool virtual machine is goes down )
i test is with nfs server but not work i user iscsci target on RHEL5 for create iscsi server
i see ha work correctly same az this
2009-11-29 12:25:44 Check prerequisites to add server (192.168.20.253) to server pool (karkas) succeed
2009-11-29 12:25:50 Check prerequisites to add server (192.168.20.253) to server pool (karkas) succeed
Select Server Pool Name Status High Availability Status Servers Users Logs
Select karkas Active Enabled Total: 2 Total: 1 View Logs
and no error in /var/log/ovs/*.log
but when add new server i see in status "error in adding server "" and when edited again see server add and active state
1-i have no ocfs2 partition on my machine use iscsi initiator
2-all server use root cluster id /var/ovs/mount/disk_id
3-all permission set for everybody and 777
any idea for solve this problem
thankshi
and very thanks for your reply
every this work good
[root@OVS2-253-32 ~]# service o2cb online
Starting O2CB cluster ocfs2: OK
[root@OVS2-253-32 ~]# service o2cb start
Starting O2CB cluster ocfs2: OK
[root@OVS2-253-32 ~]#
but see :
During adding servers ([192.168.20.253]) to server pool (jojo), Cluster setup failed: (OVM-1011 OVM Manager communication with 192.168.20.254 for operation HA Setup for Oracle VM Agent 2.2.0 failed: errcode=50006, errmsg=Do 'clusterm_init_root_sr' on servers ('192.168.20.253') failed. )
Select Server Host/IP Server Name Server Type Status Server Location Server Pool Name Logs
Select 192.168.20.254 254 Server Pool Master,Utility Server,Virtual Machine Server Active jojo View Logs
Select 192.168.20.253 253 Virtual Machine Server Error jojo View Logs
but edit this server work fine. i use doc in step by step configure and no error occur in configuration but still see this error on adding new server and HA can't works correctly (only when i power off virtual quest machine after 15 second this server goes up and live migration not work correctly )when i shutting down one virtual machine server guest still wait for powering up this server
ocfs2 kernel module load correctly
cat /var/log/ovs-agent/ovs_root.log
StackTrace:
File "/opt/ovs-agent-2.3/OVSXCluster.py", line 115, in clusterm_init_root_sr
sr.initialize()
File "/opt/ovs-agent-2.3/_storage/OVSFileSR.py", line 127, in initialize
self.sp.mount(mp)
File "/opt/ovs-agent-2.3/_storage/plugins/OVSFileSP.py", line 209, in mount
fs_spec = self.get_fs_spec()
File "/opt/ovs-agent-2.3/_storage/plugins/OVSFileSP.py", line 184, in get_fs_spec
tgt_dev = get_dev_spec(self.fs_uuid, self.fs_spec)
File "/opt/ovs-agent-2.3/_storage/plugins/OVSFileSP.py", line 82, in get_dev_spec
raise Exception("No device found: dev_uuid=%s" % dev_uuid)
are you have any idea for solve this problem ???
very thanks -
Unable to import vAppTemplate to vCloud Director with PowerCLI
I have encountered the following issue with PowerCLI and vCloud Director:
Import-CIVappTemplate cmdlet is not functioning in PowerCLI 5.8 and 6.0 against vCloud Director 5.5.
Error Message on PowerCLI:An attempt was made to move the file pointer before the beginning of the file.
Error Message on vCloud Director UI:Catalog item file transfer failed due to SSL error.
I had confirmed the issue is on each individual cell when I connect direct to the cell before running the cmdlet.
The same ovf and cmdlet is working well in PowerCLI 5.5 and 5.8 against vCloud Director 5.1.
Any suggestion is welcome.Try trashing the preferences using this free app
http://www.digitalrebellion.com/prefman/ -
Single Primary Site running SCCM 2012 SP1 with SQL 2008 SP3 CU14 on Windows Server 2008 SP1.
We are in process of upgrading to SCCM 2012 R2.
Ran the ConfigMgr 2012 R2 setup with the /TESTDBUPGRADE on SQL Server.
F:\SMSSETUP\BIN\X64\setup.exe /testdbupgrade
cm_bc1
Error: SQL Instance hosting an active site database, error cannot run Testdbupgrade on a SQL Instance which host an active site database.
We are using s-syscenter account which has SA rights on SQL and added as local admin.You should run Testdbupgrade on a copy of your database (ie a backup) rather than the "live" database.
Note that you cannot upgrade a database once you have run Testdbupgrade on it.
See here for more information
http://technet.microsoft.com/en-us/library/jj865691.aspx
Gerry Hampson | Blog:
www.gerryhampsoncm.blogspot.ie | LinkedIn:
Gerry Hampson | Twitter:
@gerryhampson -
Error while adding A/P Credit Memo!
Error while adding A/P Credit Memo..........
'G/L Accounts' (OACT) (ODBC-2028) Message - 131-183
Please advice me .....
Thanks...Hi
Check this thread this may help you.
[Re: AP Invoice - No Matching Account Error]
Regards
Balaji -
Error while adding a connector for SSL..help!!!
i'm getting this error when i added a connector for SSL and restarted tomcat
my connector tag is
<Connector keystorePass="kalima" scheme="https" port="8443" sslProtocol="TLS" redirectPort="-1" enableLookups="true" keystoreFile="Mykeystore" protocol="TLS" keystore="C:\Documents and Settings\santhoshyma\Mykeystore" clientauth="false" algorithm="SunX509" keypass="changeit" secure="true" keytype="JKS">
<Factory className="org.apache.coyote.tomcat5.CoyoteServerSocketFactory" keystorePass="kalima" keystoreFile="C:\SSLTest\Mykeystore"/>
</Connector>
LifecycleException: Protocol handler instantiation failed: java.lang.NullPointe
rException
at org.apache.coyote.tomcat5.CoyoteConnector.initialize(CoyoteConnector.
java:1368)
at org.apache.catalina.core.StandardService.initialize(StandardService.j
ava:609)
at org.apache.catalina.core.StandardServer.initialize(StandardServer.jav
a:2384)
at org.apache.catalina.startup.Catalina.load(Catalina.java:507)
at org.apache.catalina.startup.Catalina.load(Catalina.java:528)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.
java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces
sorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:324)
at org.apache.catalina.startup.Bootstrap.load(Bootstrap.java:250)
at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:424)The question is answered in CRM 7.0 forum:
Getting error while adding a custom field (with input help) through AET -
Error while adding a custom field with Input help via AET
Hi All,
I need to add two custom field under Service orders at Item level in component BT140I_SRVP.
One field is required to have the input search help f4 and autopopulates the second field
I am able to add one field(not requiring help) successfully through AET .
I have created one Zsearch_help in se11 and its successfully running and Autopopulating seocnd field while I am testing it
While adding second field through AET,I need to enter following details as -
field label,search relevant ,serach help etc.
When I type the name of my 'Zsearch_help' against field search help it gives me following error
'Search help is not compatible'.
Secondly,not getting getter and setter methods for the attrributes in BTAdminI.
Last,please tell me if i create zhelp and activate it,would it automatically appear in the list on AETwhile assiging it to input field?
Please help me out.Kindly be detailed as I am new to SAP CRM.
Thanks,
ShivaniThe question is answered in CRM 7.0 forum:
Getting error while adding a custom field (with input help) through AET -
I am getting the following error while adding record into the table CM_RECIPE_ITEM :
<h4> Error </h4>
ORA-20505: Error in DML: p_rowid=626, p_alt_rowid=CRI_ID, p_rowid2=, p_alt_rowid2=. ORA-01410: invalid ROWID ORA-06512: at "COSTMAN.CM_RECIPE_ITEM_T3_AFTER", line 11 ORA-04088: error during execution of trigger 'COSTMAN.CM_RECIPE_ITEM_T3_AFTER'
Error Unable to process row of table CM_RECIPE_ITEM.
Kindly suggest if the problem is because of the Global temporary table or the triggers given below. Also suggest the solution.
Thanking You,
Yogesh
<h4> CM_RECIPE_ITEM Table </h4>
CRI_ID------CRI_CR_ID--------CRI_BOM_CODE--------CRI_CIFG_CODE---------CRI_CIRM_CODE--------CRI_SEQ--------CRI_QTY--------CRI_RM_COST
625----------464-----------------PRODUCT3001----------FG003----------------------10---------------------------1-------------------60-----------------10
626----------464-----------------PRODUCT3001----------FG003----------------------12---------------------------2-------------------40------------------10
<h4>Global temporary table</h4>
DROP TABLE COSTMAN.INTERIM CASCADE CONSTRAINTS;
CREATE GLOBAL TEMPORARY TABLE COSTMAN.INTERIM
ROW_ID ROWID
ON COMMIT PRESERVE ROWS
NOCACHE;
CREATE OR REPLACE TRIGGER COSTMAN."CM_RECIPE_ITEM_T3"
BEFORE INSERT OR UPDATE ON "CM_RECIPE_ITEM" FOR EACH ROW
BEGIN
INSERT INTO interim VALUES (:new.rowid);
END;
<h4>Trigger to update data on CM_RECIPE table </h4>
CREATE OR REPLACE TRIGGER COSTMAN."CM_RECIPE_ITEM_T3_AFTER"
AFTER INSERT OR UPDATE ON "CM_RECIPE_ITEM"
BEGIN
FOR ds IN (SELECT row_id FROM interim) LOOP
UPDATE CM_RECIPE
SET CR_RMC = (
SELECT SUM(CRI_QTY * CRI_RM_COST)/SUM(CR_QUANTITY)
FROM CM_RECIPE_ITEM
WHERE CRI_BOM_CODE = CR_BOM_CODE
AND rowid = ds.row_id
UPDATE CM_RECIPE
SET CR_TOTAL_COST = (
SELECT CIFG_PACKING + CIFG_OVERHEAD +CIFG_OTHERS
FROM CM_ITEM_FG
WHERE CIFG_CODE = CR_CIFG_CODE
AND rowid = ds.row_id
) + CR_RMC;
UPDATE CM_RECIPE
SET CR_GROSS_MARGIN =
(SELECT CIFG_DP_RATE
FROM CM_ITEM_FG
WHERE CIFG_CODE = CR_CIFG_CODE
AND rowid = ds.row_id) - CR_TOTAL_COST) / CR_TOTAL_COST;
END LOOP;
END;
/The scripts of the tables CM_ITEM_FG, CM_RECIPE, CM_RECIPE_ITEM are as follows :
<h4>CM_ITEM_FG</h4>
ALTER TABLE COSTMAN.CM_ITEM_FG
DROP PRIMARY KEY CASCADE;
DROP TABLE COSTMAN.CM_ITEM_FG CASCADE CONSTRAINTS;
CREATE TABLE COSTMAN.CM_ITEM_FG
CIFG_CODE VARCHAR2(13 BYTE) NOT NULL,
CIFG_CCG_ID NUMBER NOT NULL,
CIFG_NAME VARCHAR2(50 BYTE) NOT NULL,
CIFG_PACKING NUMBER NOT NULL,
CIFG_OVERHEAD NUMBER NOT NULL,
CIFG_OTHERS NUMBER NOT NULL,
CIFG_DP_RATE NUMBER NOT NULL,
CIFG_CR_BY VARCHAR2(32 BYTE),
CIFG_CR_ON DATE,
CIFG_UPD_BY VARCHAR2(32 BYTE),
CIFG_UPD_ON DATE
TABLESPACE COST_MANAGER
PCTUSED 0
PCTFREE 10
INITRANS 1
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
BUFFER_POOL DEFAULT
LOGGING
NOCOMPRESS
NOCACHE
NOPARALLEL
MONITORING;
CREATE UNIQUE INDEX COSTMAN.CM_ITEM_FG_PK_001 ON COSTMAN.CM_ITEM_FG
(CIFG_CODE, CIFG_CCG_ID)
LOGGING
TABLESPACE COST_MANAGER
PCTFREE 10
INITRANS 2
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
BUFFER_POOL DEFAULT
NOPARALLEL;
CREATE UNIQUE INDEX COSTMAN.CM_ITEM_FG_UK_001 ON COSTMAN.CM_ITEM_FG
(CIFG_CODE)
LOGGING
TABLESPACE COST_MANAGER
PCTFREE 10
INITRANS 2
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
BUFFER_POOL DEFAULT
NOPARALLEL;
CREATE OR REPLACE TRIGGER COSTMAN."CM_ITEM_FG_T1"
BEFORE UPDATE ON "CM_ITEM_FG"
FOR EACH ROW
BEGIN
BEGIN
UPDATE CM_RECIPE
SET CR_TOTAL_COST = (CR_RMC + :NEW.CIFG_PACKING + :NEW.CIFG_OVERHEAD + :NEW.CIFG_OTHERS);
END;
BEGIN
UPDATE CM_RECIPE
SET CR_GROSS_MARGIN = (:NEW.CIFG_DP_RATE - CR_TOTAL_COST) / CR_TOTAL_COST;
END;
END;
ALTER TABLE COSTMAN.CM_ITEM_FG ADD (
CONSTRAINT CM_ITEM_FG_PK_001
PRIMARY KEY
(CIFG_CODE, CIFG_CCG_ID)
USING INDEX
TABLESPACE COST_MANAGER
PCTFREE 10
INITRANS 2
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
CONSTRAINT CM_ITEM_FG_UK_001
UNIQUE (CIFG_CODE)
USING INDEX
TABLESPACE COST_MANAGER
PCTFREE 10
INITRANS 2
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
ALTER TABLE COSTMAN.CM_ITEM_FG ADD (
CONSTRAINT CM_ITEM_FG_FK_001
FOREIGN KEY (CIFG_CCG_ID)
REFERENCES COSTMAN.CM_COST_GROUP (CCG_ID));
<h4>CM_RECIPE</H4>
ALTER TABLE COSTMAN.CM_RECIPE
DROP PRIMARY KEY CASCADE;
DROP TABLE COSTMAN.CM_RECIPE CASCADE CONSTRAINTS;
CREATE TABLE COSTMAN.CM_RECIPE
CR_ID NUMBER NOT NULL,
CR_CCG_ID NUMBER,
CR_EFF_FROM DATE,
CR_CIFG_CODE VARCHAR2(10 BYTE) NOT NULL,
CR_BOM_CODE VARCHAR2(50 BYTE),
CR_QUANTITY NUMBER,
CR_RMC NUMBER,
CR_TOTAL_COST NUMBER,
CR_GROSS_MARGIN NUMBER,
CR_CR_BY VARCHAR2(32 BYTE),
CR_CR_ON DATE,
CR_UPD_BY VARCHAR2(32 BYTE),
CR_UPD_ON DATE
TABLESPACE COST_MANAGER
PCTUSED 0
PCTFREE 10
INITRANS 1
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
BUFFER_POOL DEFAULT
LOGGING
NOCOMPRESS
NOCACHE
NOPARALLEL
MONITORING;
CREATE UNIQUE INDEX COSTMAN.CM_RECIPE_PK_001 ON COSTMAN.CM_RECIPE
(CR_CCG_ID, CR_ID, CR_CIFG_CODE)
LOGGING
TABLESPACE COST_MANAGER
PCTFREE 10
INITRANS 2
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
BUFFER_POOL DEFAULT
NOPARALLEL;
CREATE UNIQUE INDEX COSTMAN.CM_RECIPE_UK_001 ON COSTMAN.CM_RECIPE
(CR_ID)
LOGGING
TABLESPACE COST_MANAGER
PCTFREE 10
INITRANS 2
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
BUFFER_POOL DEFAULT
NOPARALLEL;
CREATE UNIQUE INDEX COSTMAN.CM_RECIPE_UK_002 ON COSTMAN.CM_RECIPE
(CR_BOM_CODE)
LOGGING
TABLESPACE COST_MANAGER
PCTFREE 10
INITRANS 2
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
BUFFER_POOL DEFAULT
NOPARALLEL;
CREATE OR REPLACE TRIGGER COSTMAN."CM_RECIPE_T1"
BEFORE INSERT ON "CM_RECIPE"
FOR EACH ROW
DECLARE
L_ID NUMBER;
BEGIN
IF INSERTING THEN
IF :NEW.CR_ID IS NULL THEN
--SELECT CM_RECIPE_SEQ.NEXTVAL INTO L_ID FROM DUAL;
:NEW.CR_ID := CM_RECIPE_SEQ.NEXTVAL; --L_ID;
END IF;
:NEW.CR_CR_ON := SYSDATE;
:NEW.CR_CR_BY := nvl(v('APP_USER'),USER);
END IF;
IF UPDATING THEN
:NEW.CR_UPD_ON := SYSDATE;
:NEW.CR_UPD_BY := nvl(v('APP_USER'),USER);
END IF;
END;
ALTER TABLE COSTMAN.CM_RECIPE ADD (
CHECK ("CR_EFF_FROM" IS NOT NULL) DISABLE,
CHECK ("CR_CCG_ID" IS NOT NULL) DISABLE,
CHECK ("CR_QUANTITY" IS NOT NULL) DISABLE,
CHECK ("CR_QUANTITY" IS NOT NULL) DISABLE,
CHECK ("CR_QUANTITY" IS NOT NULL) DISABLE,
CHECK ("CR_QUANTITY" IS NOT NULL) DISABLE,
CHECK ("CR_QUANTITY" IS NOT NULL) DISABLE,
CHECK ("CR_QUANTITY" IS NOT NULL) DISABLE,
CONSTRAINT CM_RECIPE_PK_001
PRIMARY KEY
(CR_ID)
USING INDEX
TABLESPACE COST_MANAGER
PCTFREE 10
INITRANS 2
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
CONSTRAINT CM_RECIPE_UK_002
UNIQUE (CR_BOM_CODE)
USING INDEX
TABLESPACE COST_MANAGER
PCTFREE 10
INITRANS 2
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
<h4>CM_RECIPE_ITEM</H4>
ALTER TABLE COSTMAN.CM_RECIPE_ITEM
DROP PRIMARY KEY CASCADE;
DROP TABLE COSTMAN.CM_RECIPE_ITEM CASCADE CONSTRAINTS;
CREATE TABLE COSTMAN.CM_RECIPE_ITEM
CRI_ID NUMBER NOT NULL,
CRI_CR_ID NUMBER NOT NULL,
CRI_BOM_CODE VARCHAR2(50 BYTE) NOT NULL,
CRI_CIFG_CODE VARCHAR2(10 BYTE) NOT NULL,
CRI_CIRM_CODE VARCHAR2(10 BYTE) NOT NULL,
CRI_SEQ NUMBER,
CRI_QTY NUMBER,
CRI_RM_COST NUMBER,
CRI_CR_BY VARCHAR2(32 BYTE),
CRI_CR_ON DATE,
CRI_UPD_BY VARCHAR2(32 BYTE),
CRI_UPD_ON DATE
TABLESPACE COST_MANAGER
PCTUSED 0
PCTFREE 10
INITRANS 1
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
BUFFER_POOL DEFAULT
LOGGING
NOCOMPRESS
NOCACHE
NOPARALLEL
MONITORING;
CREATE UNIQUE INDEX COSTMAN.CM_RECIPE_ITEM_PK_001 ON COSTMAN.CM_RECIPE_ITEM
(CRI_ID)
LOGGING
TABLESPACE COST_MANAGER
PCTFREE 10
INITRANS 2
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
BUFFER_POOL DEFAULT
NOPARALLEL;
CREATE OR REPLACE TRIGGER COSTMAN."CM_RECIPE_ITEM_T2"
BEFORE INSERT OR UPDATE ON "CM_RECIPE_ITEM"
FOR EACH ROW
BEGIN
IF :NEW.CRI_CR_ID IS NULL THEN
SELECT CR_ID INTO :NEW.CRI_CR_ID
FROM CM_RECIPE
WHERE CR_BOM_CODE = :NEW.CRI_BOM_CODE;
END IF;
END;
CREATE OR REPLACE TRIGGER COSTMAN."CM_RECIPE_ITEM_T1" BEFORE
INSERT OR UPDATE ON "CM_RECIPE_ITEM" FOR EACH ROW
DECLARE
L_ID NUMBER;
SEQ NUMBER;
BEGIN
IF INSERTING THEN
IF :NEW.CRI_ID IS NULL THEN
SELECT CM_RECIPE_ITEM_SEQ.NEXTVAL
INTO :NEW.CRI_ID
FROM dual;
END IF;
:NEW.CRI_CR_ON := SYSDATE;
:NEW.CRI_CR_BY := NVL(v('APP_USER'),USER);
SELECT (NVL(MAX(CRI_SEQ),0)+1)
INTO SEQ
FROM CM_RECIPE_ITEM
WHERE CRI_BOM_CODE = :NEW.CRI_BOM_CODE;
:NEW.CRI_SEQ := SEQ;
END IF;
IF UPDATING THEN
:NEW.CRI_UPD_ON := SYSDATE;
:NEW.CRI_UPD_BY := NVL(v('APP_USER'),USER);
END IF;
END;
ALTER TABLE COSTMAN.CM_RECIPE_ITEM ADD (
CHECK ("CRI_RM_COST" IS NOT NULL) DISABLE,
CHECK ("CRI_QTY" IS NOT NULL) DISABLE,
CHECK ("CRI_SEQ" IS NOT NULL) DISABLE,
CONSTRAINT CM_RECIPE_ITEM_PK_001
PRIMARY KEY
(CRI_ID)
USING INDEX
TABLESPACE COST_MANAGER
PCTFREE 10
INITRANS 2
MAXTRANS 255
STORAGE (
INITIAL 64K
MINEXTENTS 1
MAXEXTENTS UNLIMITED
PCTINCREASE 0
ALTER TABLE COSTMAN.CM_RECIPE_ITEM ADD (
CONSTRAINT CM_RECIPE_FK_002
FOREIGN KEY (CRI_CIRM_CODE)
REFERENCES COSTMAN.CM_ITEM_RM (CIRM_CODE),
CONSTRAINT CM_RECIPE_ITEM_FK_001
FOREIGN KEY (CRI_CR_ID)
REFERENCES COSTMAN.CM_RECIPE (CR_ID));
Yogesh -
Error while adding a job to scheduler
Hello,
I have a batch job that is running fine in both DEV and QA environment. In DEV, I am able to schedule and run it daily. I created a similar schedule in QA environment using BODS Mgmt Console/Administrator. However, upon Activating the schedule, I am getting the following error message. Would someone know why would this error be thrown and steps to troubleshoot this error?
Thanks.
[Repository:AECON_DW_REPOSITORY Schedule:Daily_Run_QA Error:Error while adding a job to scheduler]
When contacting the server above exception was encountered, so it will be assumed the schedule is not active anymore.Hi Rizwan Tahir ,
Delete the job server associated with the current batch job and recreate it.
Then try creating a new schedule using the new job server.
And take care that job server is created in QA environment.
Hope this should work.
Regards, -
Error while adding Image: ORA-00001: unique constraint
Dear all,
I have an error while adding images to MDM I can´t explain. I want to add 7231 images. About 6983 run fine. The rest throws this error.
Error: Service 'SRM_MDM_CATALOG', Schema 'SRMMDMCATALOG2_m000', ERROR CODE=1 ||| ORA-00001: unique constraint (SRMMDMCATALOG2_M000.IDATA_6_DATAID) violated
Last CMD: INSERT INTO A2i_Data_6 (PermanentId, DataId, DataGroupId, Description_L3, CodeName, Name_L3) VALUES (:1, :2, :3, :4, :5, :6)
Name=PermanentId; Type=9; Value=1641157; ArraySize=0; NullInd=0;
Name=DataId; Type=5; Value=426458; ArraySize=0; NullInd=0;
Name=DataGroupId; Type=4; Value=9; ArraySize=0; NullInd=0;
Name=Description_L3; Type=2; Value=; ArraySize=0; NullInd=0;
Name=CodeName; Type=2; Value=207603_Img8078_gif; ArraySize=0; NullInd=0;
Name=Name_L3; Type=2; Value=207603_Img8078.gif; ArraySize=0; NullInd=0;
Error: Service 'SRM_MDM_CATALOG', Schema 'SRMMDMCATALOG2_m000', ERROR CODE=1 ||| ORA-00001: unique constraint (SRMMDMCATALOG2_M000.IDATA_6_DATAID) violated
Last CMD: INSERT INTO A2i_Data_6 (PermanentId, DataId, DataGroupId, Description_L3, CodeName, Name_L3) VALUES (:1, :2, :3, :4, :5, :6)
Name=PermanentId; Type=9; Value=1641157; ArraySize=0; NullInd=0;
Name=DataId; Type=5; Value=426458; ArraySize=0; NullInd=0;
Name=DataGroupId; Type=4; Value=9; ArraySize=0; NullInd=0;
Name=Description_L3; Type=2; Value=; ArraySize=0; NullInd=0;
Name=CodeName; Type=2; Value=207603_Img8085_gif; ArraySize=0; NullInd=0;
Name=Name_L3; Type=2; Value=207603_Img8085.gif; ArraySize=0; NullInd=0;
I checked all data. There is no such dataset in the database. Can anybody give me a hint how to avoid this error.
One thing I wonder: The PermanentId is allways the same but I can´t do anything here.
BR
Roman
Edited by: Roman Becker on Jan 13, 2009 12:59 AMHi Ritam,
For such issues, can you please create a new thread or directly email the author rather than dragging back up a very old thread, it is unlikely that the resolution would be the same as the database/application/etc releases would most probably be very different.
For now I will close this thread as unanswered.
SAP SRM Moderators.
Maybe you are looking for
-
How can I use my ADC apple cinema display on my iMac 2006 with mini display port?
I got this new screen on eBay for £20 and its an old ADC display and to my annoyance I found there isn't a way to hook it up to my iMac with a mini dvi port . So I was wondering if there is a work around that the community has come up with or if its
-
10.1.1 Didn't save my work despite creating snapshots
I recently installed Mavericks and FCP 10.1.1 on a fresh drive to test it out on a small work project. Nothing but FCP X 10.1.1 was installed on the drive. It's a Mac Pro 5,1 12 core with 32GB ram. I ran through the Lynda course and went at it. Afrai
-
Help with Zebra Label Printer and Multi Order Shipping Tool- Partial Label Printing
I have a zebra gx420d which is compatible the zebra 2844 (its the new model) and I am having a hard time printing labels with the multi order shipping tool. I have the correct driver, the printer test page works fine, and everything is configured for
-
Flash page: need to 'pin' top and left perhaps too...see
Dear Experts, Thank for reading this. http://maharishihoney.safire.com/ in the above page it is behaving just like wanted, EXCEPT want the top and left side (perhaps) to be 'pinned', meaning when resizing the browser window, the top does not disappea
-
Error with report - pkg and bind var
Hi to all, i'm writing some report and i found a strange isssue. I would like to retrieve some data using packages. So, something like select dbms_xxxx(var1, var2, var3) from dual; I would like to pass through bind vars the value per each variable. I