Error in DB13 scheduled backup
Hi All,
We schedule db13 backup in SAP on DB6 database (WIN2K3 OS) the backup is completing successfully but it was giving couple of errors in JobLog. Please find the error messages as follows
"Action deleted in SDBAP at 20061129225959"
"Job cancelled after system exception ERROR_MESSAGE"
Can any one tell me is there any problem with this error. Or can i ignore if we ignore this error can we able to restore this backup file?
Thanks in advance.....
Eshwar B
Hi Eshwar,
This is a message related to jobs which have been scheduled periodically. If someone deletes such a periodic job in DB13, the job in SM37 is not deleted immediately but only gets an invalidation timestamp. If the invalidated job tries to start again in SM37, it fails with the error message you experienced.
Normally you can ignore this, as long as DB13 itselfs shows correct results. You should not interprete the jobs in SM37 only.
Depending on your SAP release there is a background job which cleans up such invalidated SM37 jobs
Best regards
Ralf
Similar Messages
-
Error if we schedule Backup in DB13
Hi Friends,
I am getting an error, if we schedule back up from DB13. It is saying "file size is greater than it can fit in an cpio header--limit is 32 bits". This error is occuring when PSAPDATA3\undo_1\undo.data1 file is in backup process. And undo.data1 file is 5GB in size. Is this could be problem or any other problem with settings in InitSID.sap. Please help me with your valuable solutions.
Regards,
NageshwarHI nageshwar,
Check the initSID.sap file for parameters CPio, dd that has mentioned. Change that according to your OS and the tape parameters also needed to be set based on your OS. After doing changes, try the backup.
Regards,
Maheswaran -
DB13 scheduled backups getting failed
Hello Experts,
Till sometime back our backups were working fine. But recently it started getting failed.
I have checked the RFC connection SAPXPG_DBDEST_PRODORADB. RFC connection test is throwing the following error.
Logon Connection Error
Error Details Error when opening an RFC connection
Error Details ERROR: timeout during allocate
Error Details LOCATION: SAP-Gateway on host PRDAPP1 / sapgw00
Error Details DETAIL: no connect of TP sapxpg from host PRODORADB
after 20 sec
Error Details COMPONENT: SAP-Gateway
Error Details COUNTER: 217995
Error Details MODULE: gwr3cpic.c
Error Details LINE: 2030
Error Details RETURN CODE: 242
Error Details SUBRC: 0
Error Details RELEASE: 700
Error Details TIME: Thu Aug 4 12:34:49 2011
Error Details VERSION: 2
Please let me know how can I rectify the issue.
Thanks & Regards,
Shanahas.KHi,
You need to check whether service in port 123 is up.In the folder /etc/services you can see the entry
For telnet aix use port number 123.Port number are mentioned in /etc/services file.check for available port in services file. and
Check the user you telnet own the privilege of remote login or not
Let me know
Regards
Thomas -
DB13 - Scheduled Update Statistics not run - Error
Hello gurus,
I´m faccing with an error in DB13, I scheduled Update statistics every day but it did not run due an error.
I think this may resulted because an authorization problem.
In /usr/sap is with this permissions:
drwxr-xr-x 15 orad01 dba 4096 Oct 18 16:34 sap
The /oracle/D01/sapcheck is with the following permissions:
drwxr-xr-x 2 orad01 dba 4096 Nov 14 20:28 sapcheck
Inside of sapcheck directory I can see the following files with permissions:
-rw-r--r-- 1 orad01 dba 32262 Oct 14 13:16 ceeimamu.sta
-rw-r--r-- 1 orad01 dba 2705 Oct 15 17:42 ceeisafo.sta
-rw-r--r-- 1 orad01 dba 2705 Oct 15 17:50 ceeisazq.sta
-rw-r--r-- 1 orad01 dba 1932 Oct 15 17:58 ceeisbie.sta
-rw-r--r-- 1 orad01 dba 1791 Oct 15 22:16 ceeisyhm.sta
-rw-r--r-- 1 orad01 dba 1931 Oct 15 22:24 ceeisyta.sta
-rw-r--r-- 1 orad01 dba 19394261 Oct 15 23:45 ceeiszph.sta
-rw-r--r-- 1 orad01 dba 1930 Nov 9 11:27 ceenjunx.sta
-rw-r--r-- 1 orad01 dba 1790 Nov 9 11:38 ceenjvuv.sta
-rw-r--r-- 1 orad01 dba 143103 Nov 9 11:40 ceenjwnr.sta
-rw-r--r-- 1 d01adm sapsys 521 Nov 16 14:46 ceeosxxw.sta
-rw-r--r-- 1 d01adm sapsys 521 Nov 16 14:49 ceeosydo.sta
-rw-r--r-- 1 d01adm sapsys 521 Nov 16 14:54 ceeosyqi.sta
-rw-r--r-- 1 d01adm sapsys 521 Nov 16 15:57 ceeotefd.sta
-rw-r--r-- 1 orad01 dba 18530 Nov 16 16:27 ceeotgun.sta
-rw-r--r-- 1 orad01 dba 996 Nov 16 16:27 connD01.log
In DB13 at details error, it show the following statements:
Job executado
Etapa 001 executada (program.RSDBAJOB, variante &0000000000016, nome usuário XNSJAD)
Execução do comando lógico BRCONNECT No host segoviad04
Parâmetros: -u / -jid STATS20101123153214 -c -f stats -t ALL
BR0801I BRCONNECT 7.20 (7)
BR0301E SQL error -2133 at location BrOraThrEnable-1, SQL statement:
'ENABLE THREADS'
BR0806I End of BRCONNECT processing: ceeqbmqh.sta2010-11-23 15.32.15
BR0280I BRCONNECT time stamp: 2010-11-23 15.32.15
BR0804I BRCONNECT terminated with errors
External program terminated with exit code 3
BRCONNECT returned error status E
Job encerrado
Can you help me please!? I do not know how to solve this situation...
Best regards,
João Dimas - PortugalThis wasn´t a new installation... this was a migration from windows/sql server to linux/oracle... and after that migration process I made an oracle upgrade to 11.2g and during this oracle upgrade we upgrade the BRtools to 7.20 version.
I set up other job from DB13 (Verify database) and also it not ran well, it show an error too, but a diferent one:
Parameters:-u / -jid VERIF20101110030000 -c force -w only_dbv -p initD01.sap -m ALL
BR0051I BRBACKUP 7.20 (7)
BR0055I Start of database backup: beeqitms.dbv 2010-11-25 03.00.06
BR0484I BRBACKUP log file: /oracle/D01/sapbackup/beeqitms.dbv
BR0477I Oracle pfile /oracle/D01/112_64/dbs/initD01.ora created from spfile /oracle/D01/112_64/dbs/spfileD01.ora
BR0068E SAP system is running or SAP user is connected to database D01 - database cannot be shut down
BR1025I Please shut down SAP system first or use the 'offline_force' option
BR0056I End of database backup: beeqitms.dbv 2010-11-25 03.00.09
BR0280I BRBACKUP time stamp: 2010-11-25 03.00.09
BR0054I BRBACKUP terminated with errors
External program terminated with exit code 3
BRBACKUP returned error status E
I also checked the permissions in /usr/sap folder and sub folders as per the link you put here... and everything is well... but tell me one thing which owner/group must have set in /usr/sap/ directory? In that help sap link it doesn´t show any suggestion in this column, so I don´t know in this case which owner and group must have set... In my case the /usr/sap/ and dba as group:
drwxr-xr-x 28 orad01 dba 4096 Nov 23 15:20 D01
Kind regards,
João Dimas - Portugal -
Error when scheduling backup job in OEM
We have Oracle 11.2 RAC on Redhat Linux. I was creating an customized backup job and get the errorsORA-01476: divisor is equal to zero
ORA-06512: at "SYSMAN.MGMT_JOB_ENGINE", line 7544
ORA-06512: at "SYSMAN.MGMT_JOB_ENGINE", line 7699
ORA-06512: at "SYSMAN.MGMT_JOB_ENGINE", line 8211
ORA-06512: at "SYSMAN.MGMT_JOB_ENGINE", line 8342
ORA-06512: at "SYSMAN.MGMT_JOB_ENGINE", line 8503
ORA-06512: at "SYSMAN.MGMT_JOB_ENGINE", line 8570
ORA-06512: at "SYSMAN.MGMT_JOBS", line 273
ORA-06512: at "SYSMAN.MGMT_JOBS", line 86
ORA-06512: at line 1 The backup command is created by OEM as backup incremental level 0 cumulative device type disk filesperset = 5 tag '%TAG' section size 500 M database;
backup device type disk filesperset = 500 tag '%TAG' section size 500 M archivelog all not backed up;
allocate channel for maintenance type disk;
delete noprompt obsolete device type disk;
release channel; Actually using other ommand also get the same error.
What is wrong? I scheduled backup job before on this server and it worked.This may be due to that the schedule frequecy is not set. Make sure Frequency Type and Repeat Every boxes get filled properly.
-
Re: Schedule Backup: Initialisation Error
Hi all,
The oracle database I am using now is 11G R2 and I am having problems doing schedule backup. I have already looked up the forums and some of the solutions posted included
1) Restarting EM
2) Recreate the schedule
The link to the forum post is here. Re: Initialization error stopping execution of scheduled backup
However, I would like to know what is the root cause for this problem, and why this is happening.
Could it be due to the database experiencing ORA-12519 issues? (http://www.dadbm.com/2011/11/oracle-listener-refused-connection-ora-12519-troubleshooting/)Hi,
See if these docs can help you solve the issue.
Troubleshooting Guide TNS - 12519 TNS - 12516 ORA -12519 ORA - 12516 [ID 552765.1]
Intermittent TNS-12516 or TNS-12519 Errors When Connecting Via Oracle Net [ID 240710.1]
Master Note for Oracle Net Services [ID 1479212.1]
What happens when you connect from sqlplus with service_name when you find this error .
What is the output of "lsnrctl status"
What is the full error message?
Did you try backing up with RMAN ?
Regards
Yoonas -
TFS 2012 Scheduled Backups - Permission error
Hi All,
I am trying to configure auto backup using the Schedule Backups wizard. However, I get the below erros during the Readiness Checks step. I have check the SQL databases but couldn't figure out which one is having issue. Need some help. Thanks
[Info @20:37:34.839] +-+-+-+-+-| Running VerifySqlServerPermissionsGranted: Verifying TFS Job Agent has permissions to create and alter databases |+-+-+-+-+-
[Info @20:37:34.839]
[Info @20:37:34.839] +-+-+-+-+-| Verifying TFS Job Agent has permissions to create and alter databases |+-+-+-+-+-
[Info @20:37:34.839] Starting Node: ALTERCREATEDATABASE
[Info @20:37:34.839] NodePath : Container/Progress/ALTERCREATEDATABASE
[Info @20:37:34.846] Node returned: Error
[Error @20:37:34.846] User does not have permission to perform this action.
[Info @20:37:34.846] Completed VerifySqlServerPermissionsGranted: Error
[Info @20:37:34.846] -----------------------------------------------------Hi Ultragc88,
Thanks for your post.
What’s the detailed version of your TFS 2012?
To create Backup plan, you must be a member of both of the following groups:
1
The Administrators security group on the server that is running the administration console for Team Foundation.
2
The SQL Server System Administrator security group. In addition, the service account for TFS (TFSService) must have
SQL Server Perform Back Up and Create Maintenance Plan permissions set to
Allow on each instance of SQL Server that hosts the databases that you want to back up.
3
The Farm Administrators group in SharePoint Foundation 2010, or an account with the permissions required to back up the farm.
If you ensure you have the above permissions correctly, but still occur the same error, please share the full backup plan creating log here.
For more information about create TFS 2012 backup plan, please refer to this document:
http://msdn.microsoft.com/en-us/library/vstudio/hh561429.aspx.
John Qiao [MSFT]
<THE CONTENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS OR IMPLIED>
Thanks
MSDN Community Support
Please remember to "Mark as Answer" the responses that resolved your issue. It is a common way to recognize those who have helped you, and makes it easier for other visitors to find the resolution later. -
Set up schedule backup error in Oracle 10g EM
Hi Friends,
I try to set up a schedule backup for oracle10g release 2 in window2003.
I got an error message when i enter ID and PW for log into host PC.
Error - Connection to host as user jimmy failed: ERROR: Wrong password for user
But I can use my name and password log into my server PC,
IN EM as
Host Credentials
To perform a backup, supply operating system login credentials to access the target database.* Username
* Password
I also try user oracle DBA id &PW. however, I got some error message,
What is worng? which ID and PW should I need to provide it?
Thanks for help!
JImHi,
I thought to answer the Question.. !!
But Anand had given the Perfect Link for your problem... You problem will be solved just follow the steps provided in the steps..!!
Anand.. Nice Reply with nice link.. !! :-)
- Pavan Kumar -
DB13 offline backup error post brools kernel upgrade
We are running a 4.6D system on Windows 2003 cluster. Recently we upgraded brtools and SAP kernel.
After that we are getting following error in our offline backup
BR0278E Command output of 'FSCMD OFFLINERESOURCE ORACLEALP
/CLUSTER=ALSTCLUS /OFFLINE=IMMEDIATE /USER=Administrator /DOMAIN=ATENA
/PWD=***************':
FS-10006: Unable to open the resource ORACLEALP
0x138F: The cluster resource could not be found.
Please advice on the same.
Nikhil
Edited by: Nikhil Deshpande on Sep 22, 2010 11:56 PMHi Nikhil
Please check this link : http://download.oracle.com/docs/html/B12071_01/messages.htm
It deals with oracle - windows cluster and the relevant error message.
Thanks
Rishi -
Schedule Backup in Web AS Java System
Hi
Can anybody tell me how to schedule DBA Activities (Like Database, Archive Log Backup) on SAP Java System as we do in ABAP System through T Code DB13 or DBACOCKPIT
Regards
Soumya DasguptaHi Warren
Thanks for your reply. I have followed that Notes. But I got stucked in the middle. Actually I am trying to connect our EP System (Which in a Java System only) to the ECC System (ABAP) for scheduling Backup Jobs and other DBA Activities through DBACOCKPIT. I am trying to add Remote System from the dbacockpit -> System Configuration -> Add Systems as follows
1. System : SID of the Remote System
2. Select Database Connection under the Remote System -> Create
3. Connection Name : Oracle
4. Database System : Oracle
5. User Name and Password : Oracle User Name and Password of Remote System
In DB Configuration Under Parameter I have given the TNS Name of of the Remote Database System.
Can you please validate the above details. Because after saving this enties I cannot run a successful test. Error : ORA-12154: TNS:could not resolve the connect identifier specified.
Pleaes help
Regards
Soumya Dasgupta -
Hi,
I am taking daily online backup from BRTOOLS on a disk(BACKUP SEVER).If I want to take the online backup through DB13 in the disk what is the procedure to be used(step by step)
Server ECC5.0
ORACLE 9.2.0.7.0
Regards
AAAHello All,
I have changed the follwing parameters in the initSID.sap profile
backup_dev_type = disk
backup_root_dir = <disk target>
stage_root_dir = <disk target>
After making changes, i schedule backup in DB13 and type
" disk " in place of tape name.
It is working fine in IDES but not working in Development system.
it is showing the below error log
Job started
Step 001 started (program RSDBAJOB, variant &0000000000013, user ID BASIS)
Execute logical command BRARCHIVE On host EFLTDS
Parameters: -u / -c force -p initEFD.sap -sd -v "DISK"
BR0002I BRARCHIVE 6.40 (15)
BR0282E Directory
Eflbackup\BACKUP\DEVBACKUP\sapbackup not found
BR0182E Checking parameter/option 'archive_copy_dir' failed
BR0007I End of offline redo log processing: adzbxsem.log 2008-10-22 11.30.36
But i am taking the backup by BRTOOLS in development system,it is working fine.
Waiting for reply.
Warm Regards
AAA -
I/O device error when trying to backup system image on my K330B running Windows 7 Home Premium
I set up my Idea Centre K330B to schedule complete system backups to an external HDD once a week. This worked fine for three months, then about a month ago a scheduled backup failed due to "device error encountered with either the source or the destination (0x8078012D)". It also gave "Additional information: The request could not be performed because of an I/O device error. (0x8007045D)"
I ran chkdsk/r on both the backup drive ( E: ) and the system drive ( C: ) and no problems were found. The backup drive has plenty of available space. I tried the backup to a freshly NTFS-formated external drive. I tried the backup with my BitDefender 2012 Anti-virus disabled. I tried the backup after booting in safe mode. Nothing works.
If I specify to backup only C: and not the reserved partition the backup completes with no problems.
I get the same error condition whether I perform the backup with Windows or the Lenovo backup software.
Is it possible I have a disk corruption on the reserve partition that is not found and repaired by the chkdsk/r C: operation?
I'm thinking about saving all important user files and rebooting to the factory settings, but if the reserver partition is damaged I might end up with a dead 4-month-old PC.
I would greatly appreciate any help or advice as to how to get these backups going again.I just tried running the Lenovo Hard Drive Quick Test both in normal mode and in safe mode. Both times it indicated a failed read test on the HDD. The last two tests also failed. I forget what those tests were called.
I am really beginning to think I have a bad HDD and the problem just happens to be in the reserved partition where my factory system software resides. -
The Volume Shadow Copy service initially was running under the context of System, so we thought that ‘System’ doesn’t have permissions to access network shares.
When the Volume Shadow Copy service was running under the context of System, this was the error logged:
“failed with following error code '0x8078014B' (There was a failure in creating a directory on the backup storage location.).”
Which is likely due to not having permissions to write to the network location.
This is a scheduled backup trying to write to a network location, so we changes the service to run under the context of an account that does have permissions to write to the network share.
Then the error changed to this:
“failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).”
HRESULT 0x8078006b
DetailedHRESULT 0x8004230f
ErrorMessage %%2155348075
BackupState 12
VolumesInfo <VolumeInfo><VolumeInfoItem Name="C:" OriginalAccessPath="C:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="1" IsIncremental="0"
BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0"
TotalNoOfFiles="0" Flags="1604" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /><VolumeInfoItem Name="D:" OriginalAccessPath="D:" State="15" HResult="-2139619228"
DetailedHResult="0" PreviousState="0" IsCritical="0" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0"
FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="68" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0"
/></VolumeInfo>
We aren’t really seeing anything that gives any hint on what the issue is.
Any ideas? Thanks in advance!We are trying to back up folders/files from 2 local drives (C: & D:), both of which have only 10% space used, and 100 GB free.
We are attempting to back the files up to a Remote Shared File (and there is 100+ GB free space out there).
If we try another network location, we receive the exact same error.
This is Windows Server 2012, not running Hyper-V and is a physical server not a VM.
Thank you for the link.
Looking in:
Event Viewer / Application and Service Logs / Microsoft / Windows / Backup / Operational
But it doesn’t seem to give any more details:
Log Name:
Microsoft-Windows-Backup
Source:
Microsoft-Windows-Backup
Date:
7/8/2013 8:00:12 PM
Event ID:
5
Task Category: None
Level:
Error
Keywords:
User:
SYSTEM
Computer:
servername.edu
Description:
The backup operation that started at '2013-07-09T02:00:06.273000000Z' has failed with following error code '0x8078006B' (Windows Backup failed to create the shared protection point on the source volumes.).
Please review the event details for a solution, and then rerun the backup operation once the issue is resolved.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-Backup" Guid="{1DB28F2E-8F80-4027-8C5A-A11F7F10F62D}" />
<EventID>5</EventID>
<Version>3</Version>
<Level>2</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x4000000000000000</Keywords>
<TimeCreated SystemTime="2013-07-09T02:00:12.872602100Z" />
<EventRecordID>30</EventRecordID>
<Correlation />
<Execution ProcessID="3028" ThreadID="3996" />
<Channel>Microsoft-Windows-Backup</Channel>
<Computer>servername.edu</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data Name="BackupTemplateID">{A421E864-A115-4288-8D12-F4878CF8A248}</Data>
<Data Name="HRESULT">0x8078006b</Data>
<Data Name="DetailedHRESULT">0x8004230f</Data>
<Data Name="ErrorMessage">%%2155348075</Data>
<Data Name="BackupState">12</Data>
<Data Name="BackupTime">2013-07-09T02:00:06.273000000Z</Data>
<Data Name="BackupTarget">\\servername\BACKUP</Data>
<Data Name="NumOfVolumes">2</Data>
<Data Name="VolumesInfo"><VolumeInfo><VolumeInfoItem Name="C:" OriginalAccessPath="C:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="1" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0"
IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0" NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="1604" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /><VolumeInfoItem
Name="D:" OriginalAccessPath="D:" State="15" HResult="-2139619228" DetailedHResult="0" PreviousState="0" IsCritical="0" IsIncremental="0" BlockLevel="0" HasFiles="1" HasSystemState="0" IsCompacted="0" IsPruned="0" IsRecreateVhd="0" FullBackupReason="0" DataTransferred="0"
NumUnreadableBytes="0" TotalSize="0" TotalNoOfFiles="0" Flags="68" BackupTypeDetermined="0" SSBTotalNoOfFiles="0" SSBTotalSizeOnDisk="0" /></VolumeInfo></Data>
<Data Name="SourceSnapStartTime">2013-07-09T02:00:06.289250300Z</Data>
<Data Name="SourceSnapEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="PrepareBackupStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="PrepareBackupEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="BackupWriteStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="BackupWriteEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="TargetSnapStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="TargetSnapEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="DVDFormatStartTime"><TimesList></TimesList></Data>
<Data Name="DVDFormatEndTime"><TimesList></TimesList></Data>
<Data Name="MediaVerifyStartTime"><TimesList></TimesList></Data>
<Data Name="MediaVerifyEndTime"><TimesList></TimesList></Data>
<Data Name="BackupPreviousState">2</Data>
<Data Name="ComponentStatus"><ComponentStatus></ComponentStatus></Data>
<Data Name="ComponentInfo"><ComponentInfo></ComponentInfo></Data>
<Data Name="SSBEnumerateStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBEnumerateEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBVhdCreationStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBVhdCreationEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBBackupStartTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SSBBackupEndTime">1601-01-01T00:00:00.000000000Z</Data>
<Data Name="SystemStateBackup"><SystemState IsPresent="0" HResult="0" DetailedHResult="0" /></Data>
<Data Name="BMR"><BMR IsPresent="0" HResult="0" DetailedHResult="0" /></Data>
<Data Name="VssFullBackup">false</Data>
<Data Name="UserInputBMR">false</Data>
<Data Name="UserInputSSB">false</Data>
<Data Name="BackupSuccessLogPath">
</Data>
<Data Name="BackupFailureLogPath">
</Data>
<Data Name="EnumerateBackupStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="EnumerateBackupEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="PruneBackupStartTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="PruneBackupEndTime"><TimesList><Time Time="1601-01-01T00:00:00.000Z" /><Time Time="1601-01-01T00:00:00.000Z" /></TimesList></Data>
<Data Name="BackupFlags">0x9</Data>
<Data Name="ComponentInfoSummary"><ComponentInfoSummary ComponentInfoArrayPresent="1" TotalComponents="0" SucceededComponents="0" /></Data>
</EventData>
</Event> -
Scheduled Backup & Manual Backup not Inintiating for CM
I am trying to do a Backup for CM. But it is not getting started it showd the error "Backup initiation timed out. Master agent might still be processing this operation or may be down.". I checked the DRF Master and Local services- it was up and running. I Restarted the service and tried, still it shows the same error and does not backup. The Backup device, scheduler is all configured and the Backups took place till last week. The Backup server is up and other backups for different sites are successful.
Guys please help me out as an upgrade is scheduled later tomorrow for that server. Thank You.Hi Bijoy Jack.
I had the same problem, and I stopped the antivirus protection service on my FTP server, after this solved my problem.
Maybe you need try this if you have a firewall or other protection file or network.
Regards.
Mariano. -
Error using Window Server Backup on 2012R2 Hyper-V to network share
Hi
I have a Windows 2012 R2 Hyper-V server. It runs a Windows 2012 R2 VM (called
server-1).
I want to backup the VM to a network location (\\network-1\server-1_backup$). To do this, I installed Windows Server Backup from the command line and configured a backup to look like this:
C:\Users\admin>wbadmin enable backup
wbadmin 1.0 - Backup command-line tool
(C) Copyright 2013 Microsoft Corporation. All rights reserved.
The scheduled backup settings:
Bare metal recovery : Not Included
System state backup: Not Included
Volumes in backup: (null)
Components in backup: HyperV\server-1
Files excluded: (null)
Advanced settings: VSS Backup Option (FULL)
Location to store backup: \\network-1\server-1_backup$\
Times of day to run backup: 04:00
But when I run this backup manually, I get the following error:
C:\Users\admin>wbadmin start backup
wbadmin 1.0 - Backup command-line tool
(C) Copyright 2013 Microsoft Corporation. All rights reserved.
Do you want to create a backup using the same configuration that you use for
scheduled backups?
[Y] Yes [N] No y
The backup operation to Scheduled backup target is starting.
Creating a shadow copy of the volumes specified for backup...
Summary of the backup operation:
The backup operation stopped before completing.
The backup operation stopped before completing.
Detailed error: A component critical volume failed to snapshot.
Log of files successfully backed up:
C:\Windows\Logs\WindowsServerBackup\Backup-23-02-2015_08-49-55.log
Log of files for which backup failed:
C:\Windows\Logs\WindowsServerBackup\Backup_Error-23-02-2015_08-49-55.log
ERROR - The shared restore point operation failed with error (0x8100010c)
No valid component or volume to snapshot.
A component critical volume failed to snapshot.
The log file then looks like this:
Writer Failures
Writer Id: {66841CD4-6DED-4F4B-8F17-FD23F8DDC3DE}
Instance Id: {3976D373-854E-4527-B85D-7B61924C8597}
Writer Name: Microsoft Hyper-V VSS Writer
Writer State: 0
Failure Result: 81000112
Application Result: 0
Application Message: (null)
Component: 1DAF1C56-0635-4043-A933-E97A62EBC139
Logical Path:
Component Result: 8100010D
Component Message: Component reports path on network share which cannot be snapshotted. (0x8100010D)
Component: 30144C93-56A2-4259-B276-86D59AC767E9
Application backup
Writer Id: {66841CD4-6DED-4F4B-8F17-FD23F8DDC3DE}
Component: 1DAF1C56-0635-4043-A933-E97A62EBC139
Caption : Offline\server-1
Logical Path:
Error : 8078001D
Error Message : The operation ended before completion.
The odd thing is that if I set this up from a Windows 2012 Server using the GUI to exactly the same network destination, the backup works no problem. It just doesn't work when using Server 2012 R2 Hyper-V configured through a command line.
Any help appreciated,
AndrewHi Andrew,
I tested this in my lab server 2012R2 , but there's no error .
I would suggest you to create a new share folder on other server then check if the issue persists .
Writer Name: Microsoft Hyper-V VSS Writer
Writer State: 0
Failure Result: 81000112
Application Result: 0
Application Message: (null)
Component: 1DAF1C56-0635-4043-A933-E97A62EBC139
Logical Path:
Component Result: 8100010D
Component Message: Component reports path on network share which cannot be snapshotted. (0x8100010D)"
According to this error , please check if the VM's resource (such as VHD file) was restored on network share .
I also searched the error "ERROR - The shared restore point operation failed with error (0x8100010c)" , but I can not find it within following article :
http://blogs.technet.com/b/filecab/archive/2009/09/16/diagnosing-failures-in-windows-server-backup-part-1-vss-spp-errors.aspx
Any further information please feel free to let us know .
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .
Maybe you are looking for
-
Can't change desktop pictures(error)
When i try to change pictures on my decktop, error comes out. i can only see the message "Loading images" but i can't click any button. Please help me to solve this problem.
-
Hi Does anyone know a quicker way to do a mass check on whether 'line item dimension' has been defined in InfoCubes? Please share if you do. Many thanks, Anthony
-
CS4 Printing in an Action creates a negative image print
I have CS4 on a Windows platform, as a trial. I wanted to see if the printing issues that keep me from using CS3 in production were solved before I bought it. Pretty much right out of the chute, I ran into problems. I use actions to get photos format
-
when i click on update box the processs stops at 2.4 mb and it gets paused which the process takes 249 mb to be complete but it dosen,t change and stays at 2.4 mb , i tried even from support website >http://support.apple.com/kb/dl1640, with that when
-
Hi all How do i create a user to a new recruiter in order to let him enter the Recruiter URL in E- Recruiting? (This user has of course R/3 user) Thanks Sharona