Error in ODS to Cube extraction

Hi All
We are in QA system. We transported our BW confing from Dev to QA system. Basically we are loading data from R3 to ODS and ODS to Cubes.
From R3 system to ODS extraction works fine we are getting data to ODS. From ODS to InfoCube the extraction fails and gives the following error message.
Error 8 when startingthe extraction program
Message no. R3019
Diagnosis
Error 8 occurred whenstarting the data extraction program.
System response
The data extraction is terminated.
Procedure
Check for relevant OSS Notes, or create a problem message of your own.
Please let me know to correct this error.
Your response in this regard is highly appreciated and its very urgent too.
Regards

HI,
Check this OSS Note : 147104
and also have a relevant thread..
Data uload to ODS ending up with an error. URGENT HELP NEEDED!!!!!!
Thanks

Similar Messages

Date load error From ODS to Cube?

Guru's,
Here is a status of data load and suggest me.
Actually we are loading data from ODS to Cube which is full load.This loading is done thorugh process chain and it is loaded for every half an hour.Every time the earlier load will be deleted and next load will be taken to cube.Two days ago the load had gone wrong.When I tried to see cause for the failure in Monitor details I could see Update missing and processing missing.When I see in process chains log view I got info stating some invalid characterstic had appeared.But when I search in PSA the whole of the data packets are green.If there is any invalid characterstics PSA should show a red status.But it is not showing.Please guide me how could I solve this?
point will be definitely awarded for the proper answers.
Thanks in advance.
vasu.

Hi Vasuvasu
Once the edit is done and reloade the sata it wont show u the records in Red..
Hope itz Helps..!
Regards
KISHORE M REDDY
**Winners Don't Do Different things,They Do things Differently...!**
> I dont whink this is with Disk space Y because after
> every full load we are deleting data.

Error with calendar date being extracted : PSA - ODS - cubes correction

Hello to all,
I have an issue with incorrect calendar date being captured by BW.
Here is the analysis:
We have red request into the invoice cubes because of incorrect calendar date. It has been found that the process is done via PSA -> ODS -> Cubes
How will I do the correction? Kindly specify on whether or not to change the status of the red QM status in the cubes. Also with the data mart status of ODS and the request of ODS? What status(has to be changed)? what request has to be deleted? Thanks.

Hi,
What I did:
changed QM status to green of the Info Cubes
deleted the green status of requests in the Info Cubes
deleted the Data Mart status of ODS
deleted the request of ODS
edited manually the data into the PSA
started the update immediately
Then....
I will wait if the request will be updated in ODS?
Then
I will check if the delta job from ODS to cube will proceed right?
Please advise. Thanks.

Error while loading data from write optimized ODS to cube

Hi All,
I am loading data from a write optimized ODS to cube
I have done Generate Export Datasource
schedulled the info packge with 1 selection for full load
then it gave me following error in Transfer IDOCs & TRFC
Info IDOC 1: IDOC with errors added
Info IDOC 2: IDOC with errors added
Info IDOC 3: IDOC with errors added
Info IDOC 4: IDOC with errors added
Data packege 1 arrived in BW Processing : selected number does not agree with transferred number
Processing below is green
shows update of 4 new records to Datapackage 1.
Please provide inputs for the resolution
Thanks & Regards,
Rashmi.

please let me know, What more details you need?
If I click F1 for error details i get following message
Messages from source system
see also Processing Steps Request
These messages are sent by IDoc from the source system. Both the extractor itself as well as the service API can send messages. When errors occur, several messages are usually sent together.
From the source system, there are several types of messages that can be differentiated by the so-called Info-IDoc-Status. The IDoc with status 2 plays a particular role here; it describes the number of records that have been extracted in a source system and sent to BI. The number of the records received in BI is checked against this information.
Thanks & Regards,
Rashmi.

Error when trying to load data from ODS to CUBE

hi,
Iam getting a short dump when trying to load data from ODS to CUBE. The Run time error is 'TYPELOAD_NEW_VERSION' and the short text is 'A newer version of data type "/BIC/AZODS_CA00" was found than one required.please help me out.

Hi,
Check this thread.........Ajeet Singh has given a good solution here.........
Re: Error With Data Load-Getting Canceled Right Away
Also check SAP note: 382480..................for ur reference............
Symptom
A DART extraction job terminates with runtime error TYPELOAD_NEW_VERSION and error message:
Data type "TXW_INDEX" was found in a newer version than required.
The termination occurs in the ABAP/4 program "SAPLTXW2 " in "TXW_SEGMENT_RECORD_EXPORT".
Additional key words
RTXWCF01, LTXW2U01, TXW_INDEX
Cause and prerequisites
This problem seems to happen when several DART extraction jobs are running in parallel, and both jobs access table TXW_INDEX.
Solution
If possible, avoid running DART extractions in parallel.
If you do plan to run such jobs in parallel, please consider the following points:
In the DART Extract configuration, increase the value of the parameter "Maximum memory allocation for index (MB)" if possible. You can estimate reasonable values with the "File size worksheet" utility.
Run parallel DART jobs on different application servers.
As an alternative, please apply note 400195.
It may help u.........
Regards,
Debjani.......

Error in updating data from ODS to CUBE.

Hi,
I am tryin to load data manually from ODS to CUBE in NW2004s.
This is a flat file load from the datasource to the ODS and then from the ODS to the CUBE.
In the CUBE, I am trying to populate fields by using the ODS fields.
For eg.
In the ODS, a CHAR Infoobject has the data in the timestamp format(i.e. mm/dd/yyyy hh:mm ). I need to split this data and assign them to the two individual DATE and TIME Infoobject in the CUBE.
For this, I have done the coding in the Transfer Structure in the Rule Group.
The time field is gettin populated , but the date field is not getting populated.
I get an error as Eg:
Value '04052007' for CHAR 0DATE is not plausible
Due to this, the corresponding records is not getting displayed
Also, the records where the time id displayed, the date is not getting displayed inspite of the date being correct.
Please help me with a solution for this.
REMOVED
Thanks In Advance.
Hitesh Shetty

Hello Hitesh
SAP accepts the date format in YYYYMMDD, so in the routine where you have concatenate the day month year...just do it in reverse order.....
Thanks
Tripple k

Error while uploading data from ODS to Cube

Hi All,
Will you please help out this issue.As this is a priority high issue,please reply if you know the answers.
I am facing an error while loading the data from ODS to CUBE,the error
is
1.Name is not in the namespace for generated BW Metaobjects
2.Error 18 in the update
And this error is occuring only in quality server.
Thanks,
Ram.

HI RAM SIVA,
make sure that the Data source is replicated and tranfer rules r active.
And also check whether the all transport requests r imported properly.
hope it helps
bhaskar

Error while loading data from ODS to CUBE.

Hi friends,
When l am loading data from ODS to Cube with help of data mart, I am getting error in QA system , IN DM system ,every thing went well.IF i see the detail tab in monitor under Processing .
Its is showing like this .
Transfer Rules : Missing Massage.
Update PSA : missing massage.
Processing end : missing message.
I have checked the coding in update rules, everything is ok.
Plz any inputs.
hari
Message was edited by:
hari reddy

Might means that IDocs flow is not defined properly in your QA system for myself-SourceSystem.
Regards,
Vitaliy

Error in Data updation From ODS TO CUBE

hello Experts
We are working on BW 3.5
for FI GL line items we are loading the data to ODS and than to Cube.
earlier there was a process chain failure 2 months back so delta were stuck for 2 months now about 10 million records have been uploaded in ODS but when i am tryint to upload these records to CUBE via delta upload its giving Error
Value 'Ã
Â ABC100711396 ' (hex. 'C30DC2A04C4344313030373131333936 ') of characteristic 0REF_DOC_NO c
i would like to know how to correct this and from where this error is coming as the same data is loaded to ODS and there its OK and secondly as there is no PSA bw ODS and Cube Do i need to delete the request and upload again
what if same error appears again should i write a start routine in update rule Between ODS and CUBE for special characters
thanks for replies

Hi,
Goto All Elementary Tests in RSRV
Goto Master data
Select the required test
Select your Infoobject
Execute the test
You will get the result with errors or no errors
If you get errors, then you click "Correct Error" button.
Regrds,
Suman

ODS to CUBE error

Hi All, Please help me out with the following error while loading from ODS to CUBE (BW3.5)
Error message when processing in the Business Warehouse
Diagnosis
An error occurred in the SAP BW when processing the data. The error is documented in an error message.
System response
A caller 01, 02 or equal to or greater than 20 contains an error meesage.

Hi,
I will suggest you to check a few places where you can see the status
1) SM37 job log (In source system if load is from R/3 or in BW if its a datamart load) (give request name) and it should give you the details about the request. If its active make sure that the job log is getting updated at frequent intervals.
Also see if there is any 'sysfail' for any datapacket in SM37.
2) SM66 get the job details (server name PID etc from SM37) and see in SM66 if the job is running or not. (In source system if load is from R/3 or in BW if its a datamart load). See if its accessing/updating some tables or is not doing anything at all.
3) RSMO see what is available in details tab. It may be in update rules.
4) ST22 check if any short dump has occured.(In source system if load is from R/3 or in BW if its a datamart load)
5) SM58 and BD87 for pending tRFCs.
Once you identify you can rectify the error.
If all the records are in PSA you can pull it from the PSA to target. Else you may have to pull it again from source infoprovider.
If its running and if you are able to see it active in SM66 you can wait for some time to let it finish. You can also try SM50 / SM51 to see what is happening in the system level like reading/inserting tables etc.
If you feel its active and running you can verify by checking if the number of records has increased in the data tables.
Thanks,
JituK

Error while loading from ODS to CUBE

Hi guys,
I am loading data from source system to ODS and from ODS to CUBE. Ok. The data came successfully from Source System to ODS. But while coming to ODS to CUBE it is showing some error at Data Packet 13. Ok. In CUBE, I loaded the data by using update ODS data to data target, at that time it shows two options like FULL UPDATE and INIT UPDATE. Then I selected FULL UPDATE and then I checked in processing tab there is only one option enabled i.e. only data target. OK and then I loaded it. Now after getting the error where I can correct it. There is no PSA option in monitoring.
Other wise how I can change option in Processing tab of infopackage for PSA. But I know one point that when we load the data from one target to another the only one option available in processing tab is only data target. How can I change that option and how can I correct the error.
Thanks
Rajesh

Hi,
i solved my question like the following.
Go to monitoring of the CUBE and select the option "read every thing as manually" -> then it shows another screen for correcting the records -> correct all the records and load the data again. ok
Thanks
Rajesh

Error when loading from ODS to Cube

Hello Friends,
I am having trouble loading data from ODS to Infocube in my 2004S system.When loading data i get this message
07/03/2007     13:10:25     Data target 'ODSXYZ ' removed from list of loadable targets; not loadable.
07/03/2007     13:28:42     Data target 'ODSXYZ ' is not active or is incorrect; no loading allowed
I checked for ODSXYZ in my data target but there is nothing by that name.Even the infopackage doesnt have it.What needs to be done.Please help.
Thanks.

Its a expected behavior. When you migrate ur DS, the infopacks associated with it, will grey out all the data targets that they were feeding before, that applies to any infopack you create even after the migration. You womt be able to delete it.
Having said this, this shouldnt impact ur loads from ODS to Cube. As this shoudl be taken care of by ur DTP's rather than ur infopacks.
A few questions:
How are you loading ur cube?
Did the data get thru fine to PSA with the infopack in question?
How did you load ur DSO(assuming the load was successful)?
Message was edited by:
        voodi

Lost Decimal Places when extracting value from ODS into Cube

Hi,
In short, we wish to transfer data from an ODS to a custom cube. One of the Key Figures is becoming an integer in the process.
Both the ODS and Cube use the same InfoObject which is defined as a Number with a Data Type of FLTP.
If I set a break-point in the update rules, I can see that it is reading the value into the communication structure correctly. Yet, when I browse the data in the Cube, it seems to have lost the decimal places in the update.
More details:
We have a custom ODS and cube which needs to store a Unit Price to four decimal places. In creating the InfoObject for Unit Price, we could not use a Data Type of Currency (Type = Amount) as this is limited to 2 decimal places.
Instead, I used a Data Type of FLTP (Floating Point) and a type of Number. All decimal places are loading correctly into the ODS, but are being lost when transferred to Cube.
Many thanks
Adrian

Hi Simon and Emmanuel,
Thanks for the suggestions.
Unfortunately the Query is returning the same integers as LISTCUBE.
Also, my key figure has the same definition in both the ODS and cube (uses the same InfoObject), and there is no transformation - just transfer.
I'd prefer not to create another currency. It could get a bit messy if I'm having to include the figure in calculation with other figures that use the real currency.
I had thought of making the key figure a standard type of Currency and multiplying the value by 100 before storing them in the cube - then I would simply divide the figures by 100 in the query. But again, not ideal.
I have logged a OSS note with SAP to see if there is any known issue with transferring a floating point number between the ODS and Cube.
Thanks
Adrian

Activating ODS to CUBE (urgent)

Hello Gurus,
I'm running an process chains where it loads data to ODS and activating ODS and loading data from ODS to CUBE ....
where my problem is while doing further processing for ODS to CUBE i'm getting an error as follows
1.Error 8 when starting the extraction program
2.Error in source system
3.Error occurred when updating data from ODS
Plz through some light urgent
Regards
Sandy

Hi,
Dont create manually from SU01, the best way is just goto SPRO -->SAP Business Information warehouse -->Automated processes --> Create User for Background Process...
The system prompts with BWREMOTE..just give a password and save it ..it would automatically pull up the necessary profiles.
Error in source systems was giving to me when i have an extractor which extraction job in R3 was cancelled.....this error is received in BW....also you can receive this error if the connection between systems is lost....check in Source Systems and check Connection in order to check if is a network problem...
ckeck the RFC connection once.
check if any dumps created ( i mean for detials)
If possible give some more details of your problem
there may be no connection with source system to BW system.
please check the same in RSA1 Source system tree for the source system, context menu, check the connection.
if not activate the transfer stru. of this object in BW system by replicating the datasource.
Check in RSRV for the prg that updates data for this ODS,Correct it if you find some errors
Goto RSRV, Select the test for ODS Updating program..give the ODS name and execute,if you get an error, you have the option to correct it there..
Hareesh

Restore failed delta from ODS to cube

Hi All,
I have started a delta load from ODS to cube but it has failed abruptly, for some reason, with out extracting even a single record.
I want to restart/re-schedule the load but I am confused how to do that(just a delta or repair/repeat delta).
Can someone please suggest how to proceed.
Rgds,
RPK.

Hi Ravi,
I had to stop the request because of some other issues and now I have to start it again. There is no particular error.
Hi PB,
Thanks a lot for the reply. Are you sure that I have to delete this failed request first? Will it prompt for a repeat delta when I try to schedule it again?
Sorry for asking these questions but just want to make sure about it.
Rgds,
RPK.

Error in ODS to Cube extraction

Similar Messages

Maybe you are looking for