Error in RAID Configuration

Now I am receiving this message: Your device My Passport (S/N: ***************) has RAID configuration issues.Please launch the WD Drive Utilities software to get more information. My options are to click on run wd drive utilities which i uninstalled...

Am experiencing exactly the same problem that e_silio describes on my MacBook Pro (late 2008 running Yosemite 10.10.4). I also have a DROBO (a "better-than-RAID" backup system) attached to Firewire port on which I have my Time Machine and an Archive partition. With the WD software installed the drive mounts for about 10 seconds then dismounts and the LED goes off. With the WD software uninstalled the drive mounts, then dismounts but LED continues powered (blinking), and the "Error in RAID Configuration" popup displays as already described. However, when I dismount the DROBO, uninstall the WD software <reboot>, the drive stays mounted!  BUT... When I install the WD Drive Utilities, let the app update to the current version (2.0.2.18 May 19, 2015), and run the "Quick Drive Test", THEN the drive dismounts. Now, disconnect the drive and re-connect: it remounts four about a minute and then dismounts again. Uninstall WD Drive Utilities, reconnect the drive, then the "Error in Raid..." message returns. (The DROBO is still disconnected from the computer). It is quite frustrating to need to fuss with such a basic device. 

Similar Messages

  • Bios not install error and Raid Configuration not showing physcial HDD in Lenovo

    Is this a SATA hard drive by any chance?  Sounds like you have an Adaptec SCSI controller, but no hard drive attached to it.  Are you booting an install DVD of some sort?

    Bios not install error and Raid Configuration not showing physcial HDD in Lenovo RD 120 Server (New)
    updated bios still same error
    and at array configuration it is not showing any hard disk
    hard disk utility it is showing hard disk 
    we are trying to install OS with single hard disk in Lenovo RD 120 Server
    This topic first appeared in the Spiceworks Community

  • VM Server installer does not recognize RAID configuration in Intel ESRT2

    Hello,
    I'm having a big issue here trying to deploy my third Oracle VM Server.
    I have:
    - A Intel Server Board S3420GPLC
    - A Intel Xeon X3440 processor
    - 16GB DDR3 ECC Memory
    - Six 1TB Hard Drives
    What I'm trying to do:
    - Create a RAID array using Intel ESRT2 (Embedded Server RAID Technology II) using all the discs (done)
    - Install Oracle VM Server into the array
    - Install some VMs....
    The problems:
    - When I boot the VM Server installer from USB stick I got an error saying that there is not enought memory. This issue is solved by typing "linux mem=15GB"
    - I got a screen per disk warning me about that the discs need to be initialized and all the data will be lost
    - When I go to the disk partitioning screen all the disks are listed separated, the installer simply don't recognize the RAID configured before.
    What I already tryied:
    - Change the RAID controller from ESRT2 to Intel Matrix
    -> Didn't solve.
    - Create a Driver Disk with the disk images supplied by Intel here
    -> I launch the installer using "linux mem=15GB noprobe=ata1 noprobe=ata2 ....". When Im asked by the installer to load the drivers it doesn't recognize the disk, so i couldn't load the drivers.
    Now, the questions:
    - Is there another driver I can use do make the vm server installer recognize the RAId configured?
    - Is there a better way to setup this server, considering that it needs to be "self contanied" (store and run vms)?
    Edited by: xyp on 14/10/2010 11:37

    So...
    - I have installed VM Server into ordinary linux partitions on the first disk.
    - I have created a big partition in the first disc with the space not used for the VM Server
    - I have created five equal partitions on the other discs
    - I have configured software raid 10 using mdadm
    Now the problem seems to be solved, i have a storage repository with almost 3TB and can deploy my VMs.
    Unfortunatelly only my windows 2008 r2 hardware virtualized vm is working, the linux paravitualized guests not. but this new issue will be a subject for another topic.

  • Is RAID configuration possible on MSI GX660 266NE gaming laptop

    [ ERROR: SPECIFIED ATTACHMENT MISSING ] Hello
    I have a GX660 266NE laptop that came installed with a single harddrive. I have now replaced it with 2 Kingston SSDNow 240 GB SSD harddrives. I have also flashed BIOS to the latest on MSI support that includes the option for RAID configuration. In BIOS I have enabled RAID but when I save this BIOS configuration I do not get the option to press ctrl+I to enter Intel Rapid Storage Tech RAID configuration.
    Any ideas of what i am missing? or is it simply not possible to make RAID running on this laptop?
    Thanks in advance and english it not my native language so excuse me for any misspelling and not correct sentences :-)

    Hi, Is your BIOS updated to version 30L?
    http://www.msi.com/support/nb/GX660.html#down-bios
    I saw a successful example on Youtube:

  • UCS 220: FlexFlash showing Raid configured on HV partition

    Does someone knows how to remove a raid configured on a FlexFlash HV partition  on UCS 220M3?
    Thanks        

    Hi Sean,
    This is a expected behavior since we have only SD card present.
    This condition is filed under this defect:CSCuh20203. The fault is cosmetic.
    UCSC 1.5 release notes should specify RAID degraded with 1 SD card.
    Symptom:
    FlexFlash Degraded RAID message with only 1 SD card
    Conditions:
    C220 M3, 1.5(1f) firmware
    Workaround:
    1) Remove all the SD cards from the system and reboot CIMC once, this error will go.
    2)  If CIMC reboot is not possible, then you need to put 2 SD cards in the  system (if it had 1), launch SCU and do a Hypervisor SYNC, this error  will go
    Chris,

  • Error while deploying configurable sku

    Error while deploying configurable sku in BCC server when i give ready for review and all it gives and INFO msg as
    Can't find display name resource and price in bundle and finally when i give accept for deployment the following error displayed .Please help me to resolve it thanks in advance waiting for your reply soon.
    12:38:11,828 ERROR [DynamoServlet]
    java.lang.NullPointerException
    at atg.bizui.activity.ActivityManager.getProcessInfo(ActivityManager.ja
    a:382)
    at atg.bizui.activity.ActivityManager.getProcessInfo(ActivityManager.ja
    a:441)
    at atg.bizui.taglib.GetProcessURLTag.doStartTag(GetProcessURLTag.java:1
    6)
    at atg.bizui.taglib.elwrap.GetProcessURLTagWrapper.doStartTag(Unknown S
    urce)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getTasks_jsp._jspx_meth_b
    z_005fgetProcessURL_005f0(getTasks_jsp.java:1615)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getTasks_jsp._jspService(
    etTasks_jsp.java:359)
    at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:70)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
    at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrappe
    .java:369)
    at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:
    22)
    at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:249)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
    at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(App
    icationFilterChain.java:290)
    at org.apache.catalina.core.ApplicationFilterChain.doFilter(Application
    ilterChain.java:206)
    at org.apache.catalina.core.ApplicationDispatcher.invoke(ApplicationDis
    atcher.java:638)
    at org.apache.catalina.core.ApplicationDispatcher.doInclude(Application
    ispatcher.java:543)
    at org.apache.catalina.core.ApplicationDispatcher.include(ApplicationDi
    patcher.java:480)
    at atg.servlet.WrappingRequestDispatcher.include(WrappingRequestDispatc
    er.java:94)
    at atg.servlet.ServletUtil.invokeInclude(ServletUtil.java:3552)
    at atg.taglib.dspjsp.IncludeTag.doEndTag(IncludeTag.java:757)
    at atg.taglib.dspjsp.elwrap.IncludeTagWrapper.doEndTag(IncludeTagWrappe
    .java:41)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getProjects_jsp._jspx_met
    dspel005finclude_005f0(getProjects_jsp.java:1192)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getProjects_jsp._jspx_met
    c005fif_005f5(getProjects_jsp.java:1119)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getProjects_jsp._jspx_met
    c005fforEach_005f0(getProjects_jsp.java:1077)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getProjects_jsp._jspx_met
    c005fwhen_005f1(getProjects_jsp.java:1036)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getProjects_jsp._jspx_met
    c005fchoose_005f1(getProjects_jsp.java:1000)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getProjects_jsp._jspServi
    e(getProjects_jsp.java:244)
    at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:70)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
    at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrappe
    .java:369)
    at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:
    22)
    at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:249)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
    at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(App
    icationFilterChain.java:290)
    at org.apache.catalina.core.ApplicationFilterChain.doFilter(Application
    ilterChain.java:206)
    at org.apache.catalina.core.ApplicationDispatcher.invoke(ApplicationDis
    atcher.java:638)
    at org.apache.catalina.core.ApplicationDispatcher.doInclude(Application
    ispatcher.java:543)
    at org.apache.catalina.core.ApplicationDispatcher.include(ApplicationDi
    patcher.java:480)
    at atg.servlet.WrappingRequestDispatcher.include(WrappingRequestDispatc
    er.java:94)
    at atg.taglib.dspjsp.IncludeTag.doEndTag(IncludeTag.java:780)
    at atg.taglib.dspjsp.elwrap.IncludeTagWrapper.doEndTag(IncludeTagWrappe
    .java:41)
    at org.apache.jsp.portlets.ProjectTodoPortlet.index_jsp._jspx_meth_dspe
    _005finclude_005f0(index_jsp.java:2712)
    at org.apache.jsp.portlets.ProjectTodoPortlet.index_jsp._jspService(ind
    x_jsp.java:381)
    at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:70)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
    at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrappe
    .java:369)
    at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:
    22)
    at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:249)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
    at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(App
    icationFilterChain.java:290)

    Error while deploying configurable sku in BCC server when i give ready for review and all it gives and INFO msg as
    Can't find display name resource and price in bundle and finally when i give accept for deployment the following error displayed .Please help me to resolve it thanks in advance waiting for your reply soon.
    12:38:11,828 ERROR [DynamoServlet]
    java.lang.NullPointerException
    at atg.bizui.activity.ActivityManager.getProcessInfo(ActivityManager.ja
    a:382)
    at atg.bizui.activity.ActivityManager.getProcessInfo(ActivityManager.ja
    a:441)
    at atg.bizui.taglib.GetProcessURLTag.doStartTag(GetProcessURLTag.java:1
    6)
    at atg.bizui.taglib.elwrap.GetProcessURLTagWrapper.doStartTag(Unknown S
    urce)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getTasks_jsp._jspx_meth_b
    z_005fgetProcessURL_005f0(getTasks_jsp.java:1615)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getTasks_jsp._jspService(
    etTasks_jsp.java:359)
    at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:70)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
    at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrappe
    .java:369)
    at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:
    22)
    at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:249)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
    at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(App
    icationFilterChain.java:290)
    at org.apache.catalina.core.ApplicationFilterChain.doFilter(Application
    ilterChain.java:206)
    at org.apache.catalina.core.ApplicationDispatcher.invoke(ApplicationDis
    atcher.java:638)
    at org.apache.catalina.core.ApplicationDispatcher.doInclude(Application
    ispatcher.java:543)
    at org.apache.catalina.core.ApplicationDispatcher.include(ApplicationDi
    patcher.java:480)
    at atg.servlet.WrappingRequestDispatcher.include(WrappingRequestDispatc
    er.java:94)
    at atg.servlet.ServletUtil.invokeInclude(ServletUtil.java:3552)
    at atg.taglib.dspjsp.IncludeTag.doEndTag(IncludeTag.java:757)
    at atg.taglib.dspjsp.elwrap.IncludeTagWrapper.doEndTag(IncludeTagWrappe
    .java:41)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getProjects_jsp._jspx_met
    dspel005finclude_005f0(getProjects_jsp.java:1192)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getProjects_jsp._jspx_met
    c005fif_005f5(getProjects_jsp.java:1119)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getProjects_jsp._jspx_met
    c005fforEach_005f0(getProjects_jsp.java:1077)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getProjects_jsp._jspx_met
    c005fwhen_005f1(getProjects_jsp.java:1036)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getProjects_jsp._jspx_met
    c005fchoose_005f1(getProjects_jsp.java:1000)
    at org.apache.jsp.portlets.ProjectTodoPortlet.getProjects_jsp._jspServi
    e(getProjects_jsp.java:244)
    at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:70)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
    at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrappe
    .java:369)
    at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:
    22)
    at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:249)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
    at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(App
    icationFilterChain.java:290)
    at org.apache.catalina.core.ApplicationFilterChain.doFilter(Application
    ilterChain.java:206)
    at org.apache.catalina.core.ApplicationDispatcher.invoke(ApplicationDis
    atcher.java:638)
    at org.apache.catalina.core.ApplicationDispatcher.doInclude(Application
    ispatcher.java:543)
    at org.apache.catalina.core.ApplicationDispatcher.include(ApplicationDi
    patcher.java:480)
    at atg.servlet.WrappingRequestDispatcher.include(WrappingRequestDispatc
    er.java:94)
    at atg.taglib.dspjsp.IncludeTag.doEndTag(IncludeTag.java:780)
    at atg.taglib.dspjsp.elwrap.IncludeTagWrapper.doEndTag(IncludeTagWrappe
    .java:41)
    at org.apache.jsp.portlets.ProjectTodoPortlet.index_jsp._jspx_meth_dspe
    _005finclude_005f0(index_jsp.java:2712)
    at org.apache.jsp.portlets.ProjectTodoPortlet.index_jsp._jspService(ind
    x_jsp.java:381)
    at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:70)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
    at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrappe
    .java:369)
    at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:
    22)
    at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:249)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
    at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(App
    icationFilterChain.java:290)

  • Raid Utility Error Message "raid utility is not supported on this computer"

    I am not doing anything that I know of, but Raid Utility keeps opening up on its own, and a message pops up multiple times a day telling me "raid utility is not supported on this computer"
    Anyone have any idea how to fix this?

    Network startup is if you want to start your macbook using a network drive.
    Keep your startup settings at your current drive.
    Raid utility doesn't apply to you since you only have one hard drive installed, unless you installed another hard drive in your optical bay.
    Fibre Channel is another type of hard drive connection via network connection.
    You can't access things you don't have installed in your macbook.  Those are there in case you decide to have a network drive start up options, a raid configuration of a fibre channel network drive.

  • Windows Server Essentials error occurred while configuring on Windows Server 2012 R2 Standard

     am attempting to install the Windows Server Essentials on a new domain controller in a new domain and forest.   I go to add roles and features and select essentials.  The config wizard says it is Updating and Preparing the Server and
    That is all the information that you need to provide. Your server is being prepared for use and may restart more than once. This may take up to 30 minutes.
    It goes to 3% and the encounters an error saying An error occurred while configuring Windows Server Essentials. Please try again.  I don't seem to find anything in the log to indicate why it fails.

    Hi boe_d,
    Based on your description, did you mean that this error was occurred in process of installing the Windows Server
    Essentials Experience Role on Windows Server 2012 R2 Standard? If I misunderstand, please don’t hesitate to let me know.
    If it is, have you re-tried the role installation? Please check if still go to 3% and then get the same error
    message.
    In addition, please add
    ServerAdmin$ account to the Logon as a service Group Policy, and then monitor the result. For more details, please refer to the following article.
    You may be unable to run post-deployment configuration wizard after you install the Windows Server Essentials
    Experience role
    http://blogs.technet.com/b/sbs/archive/2013/12/04/you-may-be-unable-to-run-post-deployment-configuration-wizard-after-you-install-the-windows-server-essentials-experience-role.aspx
    If this issue still exists, please navigate to: %windir%\Logs\CBS folder and check the CBS log file if you
    can find any error that depend on the Essentials Experience Role setup time.
    Hope this helps.
    Best regards,
    Justin Gu

  • Is there a way to run a external ssd with my mid 2011 iMac hdd in a raid configuration and basically have a fusion drive

    is there a way to run a external ssd with my mid 2011 iMac hdd in a raid configuration and basically have a fusion drive

    A Fusion Drive is not a RAID; it's a CoreStorage logical volume group. While it's technically possible to do as you suggest, there would be little or no benefit from it.

  • Creating a planned order with error "Material requires configuration"

    Dear All,
    I am facing a problem for creation of a planned order with error "Material requires configuration".
    To follow the note 180317, I change Account Assignment Category to "U" (Unknown).
    However, the system still does display the same error.
    Could you please help provide possible solution for this?
    Regards,
    Phong

    See also the following blog post:
    Configurable planned order for material variants: Exception "53: No BOM explosion due to missing configuration"
    BR
    Caetano

  • While configuring speed 1000 i am getting error as sw2-storage-vdc(config-if)# speed 1000 ERROR: Ethernet2/6: Configuration does not match the port capability.

    storage-vdc(config-if)# show module
    Mod  Ports  Module-Type                         Model              Status
    2    32     1/10 Gbps Ethernet Module           N7K-F132XP-15      ok
    sw1-gd78(config-if)# sh module
    Mod  Ports  Module-Type                         Model              Status
    2    48     1/2/4/8 Gbps FC Module              DS-X9248-96K9      ok
    4    8      10 Gbps FCoE Module                 DS-X9708-K9        ok
    7    0      Supervisor/Fabric-2a                DS-X9530-SF2AK9    active *
    8    0      Supervisor/Fabric-2a                DS-X9530-SF2AK9    ha-standby
    10   22     4x1GE IPS, 18x1/2/4Gbps FC Module   DS-X9304-18K9      ok
    Mod  Sw              Hw      World-Wide-Name(s) (WWN)
    2    5.2(2)          1.1     20:41:00:0d:ec:fb:8a:00 to 20:70:00:0d:ec:fb:8a:00
    4    5.2(2)          0.107   --
    7    5.2(2)          1.8     --
    8    5.2(2)          1.8     --
    10   5.2(2)          1.3     22:41:00:0d:ec:fb:8a:00 to 22:52:00:0d:ec:fb:8a:00
    sw1-gd78(config-if)# sh run int ethernet4/6
    !Command: show running-config interface Ethernet4/6
    !Time: Mon Feb 20 22:56:12 2012
    version 5.2(2)
    interface Ethernet4/6
      no shutdown
    sw1-gd78(config-if)# no shut
    sw1-gd78(config-if)# speed 1000
    ERROR: Ethernet4/6: Configuration does not match the port capability.
    sw1-gd72# sh int ethernet4/6 capabilities
    Ethernet4/6
      Model:                 DS-X9708-K9
      Type (SFP capable):    10Gbase-SR
      Speed:                 1000,10000
      Duplex:                full
      Trunk encap. type:     802.1Q
      Channel:               yes
      Broadcast suppression: percentage(0-100)
      Flowcontrol:           rx-(off/on/desired),tx-(off/on/desired)
      Rate mode:             dedicated
      QOS scheduling:        rx-(2q4t),tx-(1p3q4t)
      CoS rewrite:           yes
      ToS rewrite:           yes
      SPAN:                  yes
      UDLD:                  yes
      Link Debounce:         yes
      Link Debounce Time:    yes
      MDIX:                  no
      Port Group Members:    none
      TDR capable:           no
      FabricPath capable:    yes
      Port mode:             Switched
    sw1-gd72# sh int ethernet4/6 transceiver details
    Ethernet4/6
        transceiver is present
        type is 10Gbase-SR
        name is CISCO-FINISAR
        part number is FTLX8571D3BCL-CS
        revision is C
        serial number is FNS12090EMJ
        nominal bitrate is 10300 MBit/sec
        Link length supported for 50/125um OM2 fiber is 82 m
        Link length supported for 50/125um OM3 fiber is 300 m
        Link length supported for 62.5/125um fiber is 26 m
        cisco id is --
        cisco extended id number is 4
               SFP Detail Diagnostics Information (internal calibration)
                                         Alarms                  Warnings
                                    High        Low         High          Low
      Temperature   36.21 C        75.00 C     -5.00 C     70.00 C        0.00 C
      Voltage        3.29 V         3.63 V      2.97 V      3.46 V        3.13 V
      Current        8.11 mA       11.80 mA     4.00 mA    10.80 mA       5.00 mA
      Tx Power       -2.65 dBm       1.49 dBm  -11.30 dBm   -1.50 dBm     -7.30 dBm
      Rx Power       -2.21 dBm       1.99 dBm  -13.97 dBm   -1.00 dBm     -9.91 dBm
      Transmit Fault Count = 0
      Note: ++  high-alarm; +  high-warning; --  low-alarm; -  low-warning

    Ankit,
    You are trying to set speed 1000 on a 10g sfp.
    type is 10Gbase-SR
    You will need to insert a 1gig sfp and then you will be able to set the speed.
    Also, I noticed that you posted first with interface 2/6 and the output you gave me was for 4/6. Are you sure you're in the right interface?

  • An error occurred while configuring server as a directory server.  Please check your network configuration and try again.

    Hi there,
    My Mac OS X Server 8.2 got buggered after I did the following steps:
    Wiped Profile manager using "/Applications/Server.app/Contents/ServerRoot/usr/share/devicemgr/backend/wipeD B.sh"
    Clicking the Off button in the Profile Manager section of the Server.app
    Clicking the On button of the same
    Clicking on asks if I want to create a new directory master, but I know that one already exists.  Trying to continue confirms this.  So, I go and destroy it to start again, but afterward, I get the following error when trying to create the directory master:
    I've done this enough times while watching the system log to see the actual error thrown, which is:
    Nov 12 22:01:24 srv.domain.com Server[279]: An error occurred while configuring srv as a directory server:
        Error Domain=XSActionErrorDomain Code=-1 "A child action failed" UserInfo=0x7fee9516c0f0 {XSActionErrorActionsKey=(
            "Creating Open Directory master"
        ), NSLocalizedDescription=A child action failed}
    I have Googled the above and have discovered only a few entries here in these Apple communities, but have found no joy.
    Here's a similar threads: 
    https://discussions.apple.com/message/19237429#19237429
    Interestingly/confusingly, this server has been working just fine as a domain master using different domain names (on separate occasions/setups).  It was only after having clicked the OFF button in Profile Manager (after a wipe) that things stopped working.
    I could rebuild this server, as I have a backup image of it that I can restore, but I'd rather find out what's broken and fix it so as to hopefully be able to fix it if/when this ever happens to me again, learning something in the process.
    That said, I perform the following steps prior to running the Open Directory setup on a the server to try and clean it up as best possible.
    Clean up steps:
    Delete the DNS zone (and all entries).
    Turn off all server services
    Delete all file server sharepoints
    Change the host name at Hardware => SRV => Network tab.  This runs the Change Host Name program.
    Close Server.app
    Throw Server.app in the trash / Empty trash (I've also just trashed and put back with same result)
    Delete the /Library/Server directory
    Clear and recreate System keychain using "systemkeychain -vfcC" to clear out all the certs related to old host name.
    Delete all the entries in the Login keychain
    Reboot (probably don't have to)
    Re-download and install Server.app
    Run Server.app, which actually retains some settings from the last setup, though I don't know where to clean those.
    After Server setup, confirm that the host name from step 4 is what I want.
    Running "changeip -checkhostname" shows "Success".  I'm using an Internet domain name so pinging the "internal" zone (srv.domain.com) resolves with the correct internal IP, and pinging the "external" zone resolves to the correct external address on the Internet.
    It would seem like I'm all good to go, but when I try to turn on Open Directory and go through the setup prompts, I get the same "Confirm Settings" error as above.
    The *only* way that I've come close to "fixing" this is to cancel out of the Profile Manager.  Then, go destroy the open directory that already exists.  Then create the domain via the Profile Manager enabling process.  At present, this only seems work to for a "private" domain.  Neither of the two Internet domain names that I've used successfully in the past work with this (or any) method. 
    Any advice or clues you can throw my way would be most appreciated.
    Thanks,
    Kim

    Had the same problem found the answer here:
    https://discussions.apple.com/thread/3264944?start=0&tstart=0

  • Error in importing Configuration objects of PI 7.0 to PI 7.1

    Hi All,
    My server is upgraded from PI 7.0 to PI 7.1.
    I am getting Error while  importing Configuration objects of PI 7.0 to PI 7.1 now.
    Pls see the below error
    Attempt to access the 1 requested objects on 1 failed. Detailed information:  com.sap.aii.ib.core.roa.RoaObjectAccessException: Attempt to read object Adapter Metadata Mail | http://sap.com/xi/XI/System, type AdapterMetaData from application REPOSITORY on system REPOSITORY failed. Object does not exist. Detailed informatio n: Software component version with key ID: b38bcd00e47111d7afacde420a1145a5 not found
    Pls suggest

    Hi,
    It seems that adapter metadata has not been loaded into integration repository and because of that when you are trying to import configuration objects in ID then you are getting the error.
    The SAP adapter metadata objects are located under the namespace http://sap.com/xi/XI/System of software component SAP BASIS.
    What you can do is, if you have installation dvd's then you can copy from their or you can simply [_DOWNLOAD_|https://websmp205.sap-ag.de/~form/handler?_APP=00200682500000001943&_EVENT=SEARCH&HIDE=&SEARCH_SPAT=X&SEARCH_BPAT=X&SEARCH_CD=X&SEARCH_P=X&SEARCH_PV=X&SEARCH_C=X&SEARCH_CV=X&SEARCH_TA=&SEARCH_V=&HIDE_EXPERT_SEARCH=X&SEARCH_MAX_RESULT=20 ] from sap market place (refer this [thread|how to import Adapter metadata;) (you must have S-user id for this) and then after you need to do as mentioned below...
    1. First unzip the file (if it is zipped) and then put it in the import directory: \usr\sap\<SID>\SYS\global\xi\repository_server\import\
    2. Now login to IR and then from menu TOOLS ---> Import design objects and import it.
    3. After that in ID, Environment ---> Clear SLD Data Cache
    4. Now you can try to import configuration objects...
    Regards,
    Sarvesh

  • Error in the configuration for sap logon tickets

    Hi Forum,
    I use Tcode crmd_order_bp to see the BP cockpit and the error message displays as
    <b>Error in the configuration for SAP logon tickets</b>
    But if I click "Yes", system displays cockpit.
    How can I avoid this error.
    Thanks in advance
    Regards
    Shridhar

    You will still need to configure SSO (either by logon ticket or username/password). The data source access is done using the username/password configured in the UM Config dialog box.
    I can see where you're coming from with your thinking, however logon-ticket-based SSO is probably the best approach.
    Cheers,
    Darren.

  • "Template import error: No VM configure file found" on brand new setup

    Previously, I posted Console does not launch OVM 3.1.1, Win7x32 Firefox15/IE8 - Empty .jnlp file which was about VM Console not launching. Since this is a new installation, and it seemed to be a unique problem, I scratched the whole installation and started again from scratch. Everything, including the NFS file server, was re-installed from scratch CD OS installation.
    The process is pretty straightforward once you're used to it, and in less than three hours I was ready again to import my first template (a template I had imported before). But now, I submit the the request, and almost immediately the process aborts. (You can see in the information below, that 1 second passes between the Import request (06:32:36) and the failure.)
    Thing is, it takes about three minutes, even locally on the web server, to get an index of that large file (tar tzf), and at completion, the vm config file is listed.
    Am I misreading the error? My web searches for enlightenment found only one good hit on this error, and in that case it appeared to be an "out of space" issue. In this case, though, I'm importing a 5GB tarfile into a 390GB, otherwise-empty file system, so I don't think that is the issue. The failure in ovs-agent.log is below. What other information may I provide to get to the bottom of this? (Thanks for any guidance/help, of course!)
    [2012-10-31 06:31:40 3341] DEBUG (monitor:36) Cluster state changed from [Heartbeating] to [DLM_Ready]
    [2012-10-31 06:31:40 3341] INFO (notification:67) Notification sent: {CLUSTER} {MONITOR} Cluster state changed from [Heartbeating] to [DLM_Ready]
    [2012-10-31 06:31:40 3338] INFO (notification:193) Sending notification: {CLUSTER} {MONITOR} Cluster state changed from [Heartbeating] to [DLM_Ready]
    [2012-10-31 06:31:48 4914] DEBUG (service:77) discover_cluster: ()
    [2012-10-31 06:31:48 4914] DEBUG (service:85) discover_cluster: call completed.
    [2012-10-31 06:32:03 4926] DEBUG (service:77) storage_plugin_mount: ('oracle.generic.NFSPlugin.GenericNFSPlugin', {'status': '', 'admin_user': None, 'admin_host': None, 'uuid': '0004fb00000900003cf41964f3476788', 'total_sz': 0, 'admin_passwd': '******', 'storage_desc': '', 'free_sz': 0, 'access_host': 'filesrv.ps.***.com', 'storage_type': 'FileSys', 'alloc_sz': 0, 'access_grps': [], 'used_sz': 0, 'name': '0004fb00000900003cf41964f3476788'}, {'status': '', 'uuid': 'fc3564eb-ce8b-489c-96bc-df6de2cc8a11', 'ss_uuid': '0004fb00000900003cf41964f3476788', 'size': '330279518208', 'free_sz': '330075340800', 'state': 2, 'access_grp_names': [], 'access_path': 'filesrv.ps.***.com:/mnt/ps_big/repo/repo', 'name': 'nfs:/mnt/ps_big/repo/repo'}, '/OVS/Repositories/0004fb0000030000659e0ce6f2ecfb55', None, True, [])
    [2012-10-31 06:32:03 4926] INFO (storageplugin:108) storage_plugin_mount(oracle.generic.NFSPlugin.GenericNFSPlugin)
    [2012-10-31 06:32:03 4926] DEBUG (NFSPlugin:353) cmd = ['mount', '-t', 'nfs', 'filesrv.ps.***.com:/mnt/ps_big/repo/repo', '/OVS/Repositories/0004fb0000030000659e0ce6f2ecfb55']
    [2012-10-31 06:32:03 4926] DEBUG (service:85) storage_plugin_mount: call completed.
    [2012-10-31 06:32:03 4931] DEBUG (service:77) add_repository: ('filesrv.ps.***.com:/mnt/ps_big/repo/repo', '0004fb0000030000659e0ce6f2ecfb55')
    [2012-10-31 06:32:03 4931] DEBUG (service:85) add_repository: call completed.
    [2012-10-31 06:32:36 4972] DEBUG (linux:847) async call function: import_template
    [2012-10-31 06:32:36 4975] DEBUG (service:77) import_template: ('0004fb0000030000659e0ce6f2ecfb55', '0004fb0000140000fdc18a572a244015', ['http://aspire/pstop/OVM_EL5U7_X86_64_TOOLS8_52_06_PVM.tgz'])
    [2012-10-31 06:32:37 4975] INFO (notification:74) async_proc_prog: notification {ASYNC_PROC} progress PID 4975 status {'OBJECT': 'template', 'TOTAL_OBJECT_COUNT': 1, 'CURRENT_OBJECT_COUNT': 1, 'TOTAL_BYTES': 0L, 'CURRENT_BYTES': 613L, 'OPERATION': 'download'}
    [2012-10-31 06:32:37 4975] INFO (notification:67) Notification sent: {ASYNC_PROC} progress PID 4975
    [2012-10-31 06:32:37 3338] INFO (notification:193) Sending notification: {ASYNC_PROC} progress PID 4975
    [2012-10-31 06:32:37 4975] ERROR (service:96) catch_error: Template import error: No VM configure file found.
    Traceback (most recent call last):
    File "/usr/lib64/python2.4/site-packages/agent/service.py", line 94, in wrapper
    return func(*args)
    File "/usr/lib64/python2.4/site-packages/agent/hypervisor/xenxm.py", line 1041, in import_template
    raise RuntimeError('Template import error: %s' % err)
    RuntimeError: Template import error: No VM configure file found.
    [2012-10-31 06:32:37 4975] DEBUG (linux:879) ovs_async_proc: pid 4975 status 1 output Template import error: No VM configure file found.
    [2012-10-31 06:32:37 4975] INFO (notification:67) Notification sent: {ASYNC_PROC} exit PID 4975
    [2012-10-31 06:32:37 3338] INFO (notification:193) Sending notification: {ASYNC_PROC} exit PID 4975
    [2012-10-31 06:32:39 4987] DEBUG (service:77) storage_plugin_listFileSystems: ('oracle.generic.NFSPlugin.GenericNFSPlugin', {'status': '', 'admin_user': None, 'admin_host': None, 'uuid': '0004fb00000900003cf41964f3476788', 'total_sz': 0, 'admin_passwd': '******', 'storage_desc': '', 'free_sz': 0, 'access_host': 'filesrv.ps.***.com', 'storage_type': 'FileSys', 'alloc_sz': 0, 'access_grps': [], 'used_sz': 0, 'name': '0004fb00000900003cf41964f3476788'}, True)
    [2012-10-31 06:32:39 4987] INFO (storageplugin:108) storage_plugin_listFileSystems(oracle.generic.NFSPlugin.GenericNFSPlugin)
    [2012-10-31 06:32:39 4987] DEBUG (NFSPlugin:142) ENTER: listFileSysytems()
    [2012-10-31 06:32:39 4987] DEBUG (NFSPlugin:257) EXIT : listFileSysytems()
    [2012-10-31 06:32:39 4987] DEBUG (service:85) storage_plugin_listFileSystems: call completed.
    [2012-10-31 06:32:39 5005] DEBUG (service:77) discover_pool_filesystem: ()
    [2012-10-31 06:32:39 5005] DEBUG (service:85) discover_pool_filesystem: call completed.

    How did you get the template to where you staged it?
    I'd say the template is corrupt or you only have a partial template.
    I did notice the call to the template is based on the short name of the host. Can you confirm the VM manager can access the http path via short name?

Maybe you are looking for

  • Suddenly, non of all my projects are starting when opening my Premier Pro 6.0. What is the problem, all of a sudden?...

    HI! Please help me! I'm a kind of desperate since my Premiere Pro suddenly doesn't seen to want to open all my files I'm working on. A message appears instead: "This project could not be loaded, it may be damaged or containing outdated elements." I d

  • Create an Image in JDialog

    Hi, I am using Eclipse to create a GUI application. My problem is this... When I run it in Eclipse it finds the images just fine and they show up perfectly... But when I export to a JAR file, the image files either are distorted or don't show up at a

  • Inserting into empty resultSet

    hey every one; iam trying to make an insert iont table using ResultSet the result set was empty (No Data retieved from the DB because of a condition or an empty table. the code was : ResultSet rs22=null; try Driver Manager.RegisterDriver(new oracle.j

  • Solaris 9 IPSec support

    I am currently attempting to activate IPSecurity on Solaris and I am having a host of issues. I am hoping someone on the forums have done this before. Here are the steps that I have figured out: 1) Create Certificates and add them into the database:

  • I've deleted ThotKey using a third-party tool on my Tecra notebook

    Hello, My laptop was slow. So I used hijackthis and found few suspicious entries. I deleted them. One of them was thotkey. Now my function keys are not working. So FN + F1 to FN + F12 is not working. I have Tecra A series with XP 32-bit OS. From wher