Error in virtual machine event log "disk 1 has been surprise removed"
I have setup hyper-v server 2012 on my server. there is only 1 VM running with 4 GB ram & 1.5 TB expanding hard drive.
I have found error in guest os "disk 1 has been surprise removed"
can any one tell me what is this error exactly. after this error i have checked hyper-v manager & found machine is showing
"Merge In Progress"
i never saw "disk 1 has been surprise removed"
error. is this error occur because of hyper-v server is not configured properly.
Also i have server 2008 R2 DC x64 which is working as hyper-v host. I have checked event logs of same and found following error.
"The disk signature of disk 2 is equal to the disk signature of disk 1."
what is this.
Akshay Pate
I use CA-ArcServer Backup. Their technical support just verified this "warning" can be ignored.
This applies to 2008 - 2012R2. The warning is from VSS. You can disable VSS to stop the warnings, but be forewarned you will cause system instability by disabling VSS.
This is caused by the backup process (specifically imaging) that runs with CA-ArcServe and Windows Backup (and probably others). For CA-ArcServer, you can disregard the other event that coincides with the event id: 157.
I also verified my backups are working, did a file/folder restore test, and restored some emails (I run Exchange 2013 SP1 on this 2012R2 server too), which all worked fine and these restores also caused the 157 warnings.
Hope this eases someone's mind. I get all edgy when I see errors I do not recognize or have never seen before.
Similar Messages
-
Error 10698 Virtual machine could not be live migrated to virtual machine host
Hi all,
I am running a fail over cluster of
Host:
2 x WS2008 R2 Data Centre
managed by VMM:
VMM 2008 R2
Virtual Host:
1x windows 2003 64bit guest host/virtual machine
I have attempted a live migration through VMM 2008 R2 and im presented withe the following error:
Error (10698)
Virtual machine XXXXX could not be live migrated to virtual machine host xxx-Host01 using this cluster configuration.
(Unspecified error (0x80004005))
What i have found when running the cluster validation:
1 out of the 2 hosts have an error with RPC related to network configuration:
An error occurred while executing the test.
Failed to connect to the service manager on 'xxx-Host02'.
The RPC server is unavailable
However there are no errors or events on host02 that are showing any probelms at all.
In fact the validation report goes on to showing the rest of the configuration information of both cluster hosts as ok.
See below:
List BIOS Information
List BIOS information from each node.
xxx-Host01
Gathering BIOS Information for xxx-Host01
Item Value
Name Phoenix ROM BIOS PLUS Version 1.10 1.1.6
Manufacturer Dell Inc.
SMBios Present True
SMBios Version 1.1.6
SMBios Major Version 2
SMBios Minor Version 5
Current Language en|US|iso8859-1
Release Date 3/23/2008 9:00:00 AM
Primary BIOS True
xxx-Host02
Gathering BIOS Information for xxx-Host02
Item Value
Name Phoenix ROM BIOS PLUS Version 1.10 1.1.6
Manufacturer Dell Inc.
SMBios Present True
SMBios Version 1.1.6
SMBios Major Version 2
SMBios Minor Version 5
Current Language en|US|iso8859-1
Release Date 3/23/2008 9:00:00 AM
Primary BIOS True
Back to Summary
Back to Top
List Cluster Core Groups
List information about the available storage group and the core group in the cluster.
Summary
Cluster Name: xxx-Cluster01
Total Groups: 2
Group Status Type
Cluster Group Online Core Cluster
Available Storage Offline Available Storage
Cluster Group
Description:
Status: Online
Current Owner: xxx-Host01
Preferred Owners: None
Failback Policy: No failback policy defined.
Resource Type Status Possible Owners
Cluster Disk 1 Physical Disk Online All Nodes
IP Address: 10.10.0.60 IP Address Online All Nodes
Name: xxx-Cluster01 Network Name Online All Nodes
Available Storage
Description:
Status: Offline
Current Owner: Per-Host02
Preferred Owners: None
Failback Policy: No failback policy defined.
Cluster Shared Volumes
Resource Type Status Possible Owners
Data Cluster Shared Volume Online All Nodes
Snapshots Cluster Shared Volume Online All Nodes
System Cluster Shared Volume Online All Nodes
Back to Summary
Back to Top
List Cluster Network Information
List cluster-specific network settings that are stored in the cluster configuration.
Network: Cluster Network 1
DHCP Enabled: False
Network Role: Internal and client use
Metric: 10000
Prefix Prefix Length
10.10.0.0 20
Network: Cluster Network 2
DHCP Enabled: False
Network Role: Internal use
Metric: 1000
Prefix Prefix Length
10.13.0.0 24
Subnet Delay
CrossSubnetDelay 1000
CrossSubnetThreshold 5
SameSubnetDelay 1000
SameSubnetThreshold 5
Validating that Network Load Balancing is not configured on node xxx-Host01.
Validating that Network Load Balancing is not configured on node xxx-Host02.
An error occurred while executing the test.
Failed to connect to the service manager on 'xxx-Host02'.
The RPC server is unavailable
Back to Summary
Back to Top
If it was an RPC connection issue, then i shouldnt be able to mstsc, explorer shares to host02. Well i can access them, which makes the report above is a bit misleading.
I have also checked the rpc service and it has started.
If there is anyone that can shed some light or advice me oany other option for trouble shooting this, that would be greatley appreciated.
Kind regards,
ChuckyHi all,
I am running a fail over cluster of
Host:
2 x WS2008 R2 Data Centre
managed by VMM:
VMM 2008 R2
Virtual Host:
1x windows 2003 64bit guest host/virtual machine
I have attempted a live migration through VMM 2008 R2 and im presented withe the following error:
Error (10698)
Virtual machine XXXXX could not be live migrated to virtual machine host xxx-Host01 using this cluster configuration.
(Unspecified error (0x80004005))
What i have found when running the cluster validation:
1 out of the 2 hosts have an error with RPC related to network configuration:
An error occurred while executing the test.
Failed to connect to the service manager on 'xxx-Host02'.
The RPC server is unavailable
However there are no errors or events on host02 that are showing any probelms at all.
In fact the validation report goes on to showing the rest of the configuration information of both cluster hosts as ok.
See below:
List BIOS Information
List BIOS information from each node.
xxx-Host01
Gathering BIOS Information for xxx-Host01
Item Value
Name Phoenix ROM BIOS PLUS Version 1.10 1.1.6
Manufacturer Dell Inc.
SMBios Present True
SMBios Version 1.1.6
SMBios Major Version 2
SMBios Minor Version 5
Current Language en|US|iso8859-1
Release Date 3/23/2008 9:00:00 AM
Primary BIOS True
xxx-Host02
Gathering BIOS Information for xxx-Host02
Item Value
Name Phoenix ROM BIOS PLUS Version 1.10 1.1.6
Manufacturer Dell Inc.
SMBios Present True
SMBios Version 1.1.6
SMBios Major Version 2
SMBios Minor Version 5
Current Language en|US|iso8859-1
Release Date 3/23/2008 9:00:00 AM
Primary BIOS True
Back to Summary
Back to Top
List Cluster Core Groups
List information about the available storage group and the core group in the cluster.
Summary
Cluster Name: xxx-Cluster01
Total Groups: 2
Group Status Type
Cluster Group Online Core Cluster
Available Storage Offline Available Storage
Cluster Group
Description:
Status: Online
Current Owner: xxx-Host01
Preferred Owners: None
Failback Policy: No failback policy defined.
Resource Type Status Possible Owners
Cluster Disk 1 Physical Disk Online All Nodes
IP Address: 10.10.0.60 IP Address Online All Nodes
Name: xxx-Cluster01 Network Name Online All Nodes
Available Storage
Description:
Status: Offline
Current Owner: Per-Host02
Preferred Owners: None
Failback Policy: No failback policy defined.
Cluster Shared Volumes
Resource Type Status Possible Owners
Data Cluster Shared Volume Online All Nodes
Snapshots Cluster Shared Volume Online All Nodes
System Cluster Shared Volume Online All Nodes
Back to Summary
Back to Top
List Cluster Network Information
List cluster-specific network settings that are stored in the cluster configuration.
Network: Cluster Network 1
DHCP Enabled: False
Network Role: Internal and client use
Metric: 10000
Prefix Prefix Length
10.10.0.0 20
Network: Cluster Network 2
DHCP Enabled: False
Network Role: Internal use
Metric: 1000
Prefix Prefix Length
10.13.0.0 24
Subnet Delay
CrossSubnetDelay 1000
CrossSubnetThreshold 5
SameSubnetDelay 1000
SameSubnetThreshold 5
Validating that Network Load Balancing is not configured on node xxx-Host01.
Validating that Network Load Balancing is not configured on node xxx-Host02.
An error occurred while executing the test.
Failed to connect to the service manager on 'xxx-Host02'.
The RPC server is unavailable
Back to Summary
Back to Top
If it was an RPC connection issue, then i shouldnt be able to mstsc, explorer shares to host02. Well i can access them, which makes the report above is a bit misleading.
I have also checked the rpc service and it has started.
If there is anyone that can shed some light or advice me oany other option for trouble shooting this, that would be greatley appreciated.
Kind regards,
Chucky
Raja. B -
Error creating virtual machine on ESX host
We are running SCVMM 2012 R2, ESX and vCenter 5.1. I have created a vmdk using VMWare's Virtual Disk utility.
I am attempting to create a VM from this blank vmdk and receive the following error:
Error (2947)
Virtual Machine Manager cannot complete the VirtualCenter action on the server <esx-hostname> because of the following error: Failed to open disk scsi0:0: Unsupported or invalid disk type 7. Ensure that the disk has been imported..
Unknown error (0x194)
Recommended Action
Resolve the issue and then try the operation again.
I do not understand the problem as the disk has been imported in SCVMM and created using VMware's own disk creation utility. Any assistance is greatly appreciated.It looks like your disk drive may have bad sectors on it, and when the dd copy reaches those bad sectors, it reports an error. Check /var/log/messages on the OVM server to see if it reports disk errors.
-
Error: no boot disk has been detected or the disk has failed!(pavilion 20)
Error: no boot disk has been detected or the disk has failed!(pavilion 20-b014 . The machine came originally with windows 8. I upgraded to windows 8.1 and put new hard disk. So the hard disk is fine.
However if I turn the machine off for a day and start the next day I get the "Error: no boot disk has been detected or the disk has failed".
I made the hard disk the first to boot the machine will boot and works. Is there a way to upadate the BIOS on
HP pavilion 20-b014? my bios version is 12/4/2012 v.8.09.
I do not understand why the intermittment above error showing on and off.
Please help. ThanksHello @Samya,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that your desktop computer is giving you an error message stating that the boot disk could not be detected, and I would be happy to assist you in this matter!
To ensure that your hard drive you computer is trying to boot from is in working order, I recommend following the steps in this document on Testing for Hardware Failures (Windows 8). This should help determine if there is a fault with the hard drive.
If the hard drive passes all of the required tests, I recommend returning the BIOS back to its default settings by following this document on Recovering the BIOS.
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping! -
"ERROR: No boot disk has been detected or the disk has failed." On HP Envy 20
Hello - I have an ENVY 20 All-in-One PC and up until yesterday it was running fine. When I turned on my PC, a black screen appeared with the message: "ERROR: No boot disk has been detected or the disk has failed." I followed the directions on this post and ran a Hard Disk Test in BIOS. I've run both the Quick Check and the Extensive Check and both were passed. I'm not sure what to do now. Any solutions? Thanks,mgmartinelli
Mgmartinelli, welcome to the forum. It appears that you may be getting some conflicting information. The error message that you first received is normally attributed to a failed/ing hard drive. You may want to disconnect the drive and reconnect it to see if that helps. Please click the "Thumbs up + button" if I have helped you and click "Accept as Solution" if your problem is solved.
-
Microsoft Virtual Machine Bus Network Adapter has a yellow !
Hi in my device manager the Microsoft Virtual Machine Bus Network Adapter ? the Microsoft Virtual Machine Bus Network Adapter has a yellow !
Does anyone know how to fix this?Hi
Firsly try to run Windows updates and see if it can be detected by Windows update and install apprpriate driver ..
Secondly if that did not work try to RIGHT click the Microsoft Virtual Machine Bus Network Adapter and click update driver and choose let Windows look for driver .
Post me your findings
Checkurtech
****Click the White Kudos star to say thanks****
****Please mark Accept As Solution if it solves your problem**** -
Hello,
We are getting this error on one of our DFSR shares and am not sure how to get this fixed. We have over 30 different shares replicating and all of them are fine except for one. I have tried to remove the Replication and the namespace and have recreated them
both and continue to get the same error. This is what is in the event logs on the server;
The DFS Replication service stopped replication on the replicated folder at local path E:\SHARE\Sharelocation.
Additional Information:
Error: 9098 (A tombstoned content set deletion has been scheduled)
Additional context of the error:
Replicated Folder Name: Sharelocation
Replicated Folder ID: 9BDA3E5A-8103-481F-84B2-269AE8A3BBC8
Replication Group Name: SHARE
Replication Group ID: C25E73B7-5B65-4299-A1BE-76E723443B02
Member ID: 568CC517-3329-42A4-ABAD-633CB3D1EF2E
If anyone has any suggestion on how to get this working again it would be greatly appreciated.Here is a short summary of what I did:
Look in Event Viewer and identify all the replication groups/folders that are giving the tombstone error. Once you have them identified, go into DFS Management GUI and completely delete the replication group
associated with that folder. You do not need to delete the DFS Namespace for that folder, just the replication functionality of that namespace folder. If you have other replication groups in your DFS-R that do not get the 9098 errors, then you do not have
to do this for these folders.
Stop DFSR services (you may need to kill the service using the taskkill command if it hangs when it tries to stop).
Give yourself permissions to the hidden System Volume Information folder. If you're account is under the domain admins group, you can simply add the security group.
This folder exists on all servers that is a member of the replication group. In my situation, 2 of the 3 servers didn't show this folder as existing even when I enabled to see hidden folders. If this happens to you,
the server is lying to you that it's not there. It is there. Don't listen to it. My suggestion is to download and use the 7-zip file manager. It will see the folder and will help you set the permissions to
it as well as delete files that are longer than 256 characters, which is an issue if you do the next step from the command line).
Note, after you set the permissions, it might tell you that you still don't have access to that folder. Just close out of 7-zip and open it back up. It should let you in that folder as well as its subfolders.
Once you have access to that folder, go ahead and delete the DFSR folder that resides underneath it. You will want to do this on all servers that has the DFSR role installed and is a member to any replication
groups. You can use the command line command "rmdir", but it fails to delete files/folders that are longer than 256 characters. This is why the 7-zip file manager is a better option to delete the DFSR folder under System Volume Information. However,
there are instances where 7-zip is unable to delete a file or folder. If you run in that scenario, use the rmdir command in an elevated command prompt. Essentially, a combination of these two will eventually clear out everything you need to clear out.
Turn DFSR services back on. This will begin the process of recreating the DFSR hash and virtual tree that you had just deleted.
Recreate the replication group that you want.
On the replication groups that you did not delete, you may get the warning: "The DFS Replication service initialized the replicated folder at local path <path> and is waiting to perform initial
replication. The replicated folder will remain in this state until it has received replicated data, directly or indirectly, from the designated primary member."
If you do, what you need to do is run the command line to set one of the DFSR servers as the primary server for that replication group, and then once set - this
is important - you will have to go in the DFS Management GUI, click on the replication group with the associated warning, select the connections tab, and then right click the the sending member that
you just made as primary and choose "Replicate now..." This will initialize the replication and you will have to do this just that once for it to replicate here on out. You will need to do choose the "Replicate now..." option for each receiving
member that the sending member/primary member server is attached to in that replication group.
Wait about 5-10 minutes and run the dfsrdiag backlog command on each replicationgroup and see if a backlog for replication/sync gets created. Run this command each 5 to 10 minutes to see if the backlog file count value decreases. If it does, it's syncing/replicating.
Don't forget that when testing replication, you cannot create test files via the local path and see if it replicates. You must create it in the DFS Namespace (\domain\folder\share) to see if replication works. Otherwise
you get false negatives and you think replication is still broken. Just an FYI. -
Touchsmart 610, windos 7 64, Error message: PXE-E61: Media tet failure, check cable. PXE-MOF: Existing PXROM ERROR: No boot disk has been detected or the disk has failed.
I used external HD, stop working , not responding, so i turn off.
HP Vision Hardware Diagnostics
Poduct: Rfrb 610-1180qd
SKU: LL606AAR
S/N: [Personal Information Removed]
Testing CPU-Passed
Hard Drive Connection Test - Passed
Boot Test - Failed Error Code - BIOHD4
Warning: Boot Sector Corrupted/ Not Found
How can i solve this problem, without using my windows vista boot disk, because i lost my windows 7 boot disk.
Thanks
G.Thank´s for your help, but i live in Brazil, so i will try the suport of HP here. I will need luck.
-
Render log file has been written to Drive :\u(200101)
Hi
I am setting up a ADS server. (NW2004s)
When I test using FP_PDF_TEST_00, it returns me the version information
(Version Information: 705.20051005114147.242570)
But when I test <b>FP_TEST_00</b>. I get the error
The render log file has been written to <Drive>:\u(200101)
Now in the server I went to <drive>:\usr\sap\<SID>\SYS\global\AdobeDocumentServices\renderErrorLog\errorFiles
I check the error file ithas the message <b>No Error Reported</b>
If there are no errors, then why is the program FP_TEST_00 is not displaying the result in pdf format?
Thanks for your help
Regards
smHi
Thanks Ramakrishna.
Now I could get the detailed trace. It given below, please let me know what could the issue
Begin trace
Adobe Document Services Wed Nov 29 10:33:23 CST 2006 Trace Results:
String: rp.script.uri = sap/SAPPDFDocument.rps
String: Trace = 4
String: Username = ABC123
Stream: PDFDocument
Stream: XFD
IIOP service is running
Created a Data Manager for this request
Locating stream: PDFDocument and loading into a DOM
PdfDocument bytes = 725
Processing PDFDocument instructions
Parsing the request
Checking request semantics
Request initialization (including DOM construction and validation) processing execution time = 16 ms.
Action: Identity
<Identity><Application> = SAFP
<Identity><Form> = FP_TEST_00
<Identity><SID> = AAA
<Identity><Client> = 110
<Identity><IsProductive> = 0
Action: Renderer
Using Template Template (xdp):
Source = URL
Name = dest:FP_ICF_DATA_AAA//sap/bc/fp/form/layout/FP_TEST_00.XDP?fp-language=DE
CacheInfo =
Setting PDFDynamic to default 0 for this PDF.
Stream = PDFOut
Input node: <Render><Output> = pdf
Data: XFD
No custom config file found.
Using standard config file: AdobeDocumentServices\lib\xfa.xci
Config setup completed.
Processing exception during a "Renderer" operation.
Request start time: Wed Nov 29 10:33:23 CST 2006
com.adobe.ProcessingError: File not found on: URL location: dest:FP_ICF_DATA_AAA//sap/bc/fp/form/layout/FP_TEST_00.XDP?fp-language=DE
Exception Stack Trace:
com.adobe.ProcessingError: File not found on: URL location: dest:FP_ICF_DATA_AAA//sap/bc/fp/form/layout/FP_TEST_00.XDP?fp-language=DE
at com.adobe.ads.util.FileUtils.getPDFDataFromInput(FileUtils.java:210)
at com.adobe.ads.request.Template.setPDFData(Template.java:222)
at com.adobe.ads.request.Renderer.initializeTemplates(Renderer.java:468)
at com.adobe.ads.request.Renderer.execute(Renderer.java:395)
at com.adobe.BaseADSRequest.doWork(BaseADSRequest.java:111)
at com.adobe.AdobeDocumentServicesWorker.processRender(AdobeDocumentServicesWorker.java:1142)
at com.adobe.AdobeDocumentServicesWorker.execute(AdobeDocumentServicesWorker.java:598)
at com.adobe.AdobeDocumentServicesEJB.processRequest(AdobeDocumentServicesEJB.java:130)
at com.adobe.AdobeDocumentServicesEJB.rpData(AdobeDocumentServicesEJB.java:108)
at com.adobe.AdobeDocumentServicesLocalLocalObjectImpl0.rpData(AdobeDocumentServicesLocalLocalObjectImpl0.java:120)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:324)
at com.sap.engine.services.webservices.runtime.EJBImplementationContainer.invokeMethod(EJBImplementationContainer.java:126)
at com.sap.engine.services.webservices.runtime.RuntimeProcessor.process(RuntimeProcessor.java:157)
at com.sap.engine.services.webservices.runtime.RuntimeProcessor.process(RuntimeProcessor.java:79)
at com.sap.engine.services.webservices.runtime.servlet.ServletDispatcherImpl.doPost(ServletDispatcherImpl.java:92)
at SoapServlet.doPost(SoapServlet.java:51)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:390)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:264)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:347)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:325)
at com.sap.engine.services.httpserver.server.RequestAnalizer.invokeWebContainer(RequestAnalizer.java:887)
at com.sap.engine.services.httpserver.server.RequestAnalizer.handle(RequestAnalizer.java:241)
at com.sap.engine.services.httpserver.server.Client.handle(Client.java:92)
at com.sap.engine.services.httpserver.server.Processor.request(Processor.java:148)
at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)
at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
at java.security.AccessController.doPrivileged(Native Method)
at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:100)
at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:170)
Caused by: java.io.FileNotFoundException: Destination exception while retrieving destination
at com.adobe.ads.util.FileUtils.getURLStream(FileUtils.java:452)
at com.adobe.ads.util.FileUtils.getPDFDataFromURL(FileUtils.java:572)
at com.adobe.ads.util.FileUtils.getPDFDataFromInput(FileUtils.java:200)
... 34 more
Caused by: com.sap.security.core.server.destinations.api.DestinationException: [destination_0001] The properties for destination FP_ICF_DATA_AAA of type HTTP could not be located.
at com.sap.security.core.server.destinations.service.DestinationServiceImpl.getDestination(DestinationServiceImpl.java:166)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:324)
at com.sap.engine.services.rmi_p4.reflect.LocalInvocationHandler.invokeInternal(LocalInvocationHandler.java:77)
at com.sap.engine.services.rmi_p4.reflect.AbstractInvocationHandler.invoke(AbstractInvocationHandler.java:53)
at $Proxy103.getDestination(Unknown Source)
at com.adobe.ads.util.FileUtils.getURLStream(FileUtils.java:444)
... 36 more
Caused by: com.sap.exception.io.SAPIOException: <Localization failed: ResourceBundle='com.sap.exception.io.IOResourceBundle', ID='No such destination FP_ICF_DATA_AAA of type HTTP exists ', Arguments: []> : Can't find resource for bundle java.util.PropertyResourceBundle, key No such destination FP_ICF_DATA_AAA of type HTTP exists
at com.sap.security.core.server.destinations.io.ConfigurationManagerStorage.get(ConfigurationManagerStorage.java:123)
at com.sap.security.core.server.destinations.service.DestinationServiceImpl.getDestination(DestinationServiceImpl.java:136)
... 44 more
Merging log data with log.pdf
Merge result: Success with information
Successfully merged data into dataless log.pdf.
Action: Render Error Log
Embedding file/stream: pdfDocument.xml using ID: pdf doc MimeType: Description: Document Services Control Stream into PDF: C:\WINDOWS\Temp\adobewa_GAD_29997650\DM-1666978463314757527.dir\DM-6806111980545081106.tmp
Instantiate PDFMM CORBA connection execution time = 0 ms.
Error embedding request inputs in error log.:
java.lang.NullPointerException
Thanks,
SM -
Internet Download error message: the connection with the server has been reset
With an WRT54GS v6 firmware v 1.50.9 on Windows XP SP2 with Internet Explorer 7, Intel wireless internal adaptor w/ 802.11b, I was getting the error message "The connection with the server has been reset" when downloading most anything from the Internet. My IP address would then be reset and download would be interrupted. To resolve, I turned off the WZC (Wireless Zero Configuration) Services, and this seems to correct the problem.
Control Panel > Admin Tools > Services > Wireless Zero Configuration > Disable
Hopes this helps.Hi!
Im using Windows 7.... I tried looking for the Wireless Config - but it isn't in the Services options!
So, what can I do now?
Thanx -
Getting error while calling this BAPI:Field MATNR has been transferred inco
Hi,
I have a rquirement to upload material master data into sap for Plant 1251.(For plant 1251 we need to upload both Basi veiw and Extended View).
I am getting the following error while calling this BAPI.Field MATNR has been transferred inconsistently or is blank
the errror is :Field MATNR has been transferred inconsistently or is blank.
I have written the below logic in the program to upload material master data into SAP.
Please help me out to resolve this issue.
Thanks in advance.
Program logic which i have wriiten in the program is
LOOP AT it_rpt.
CLEAR lwa_return.
v_tabix = sy-tabix.
IF ( it_rpt-werks EQ p_werks AND
it_rpt-matnr IS INITIAL ).
retrieve internal number
PERFORM get_internal_number USING lc_mtart
lc_mbrsh
CHANGING it_rpt-matnr.
ENDIF.
IF NOT it_rpt-matnr IS INITIAL.
PERFORM convert_field_input CHANGING it_rpt-matnr.
ENDIF.
Header data
CLEAR lwa_headdata.
lwa_headdata-material = it_rpt-matnr.
lwa_headdata-ind_sector = lc_mbrsh.
lwa_headdata-matl_type = lc_mtart.
lwa_headdata-basic_view = 'X'.
IF NOT it_rpt-vkorg IS INITIAL.
lwa_headdata-sales_view = 'X'.
ENDIF.
lwa_headdata-purchase_view = 'X'.
lwa_headdata-mrp_view = 'X'.
lwa_headdata-storage_view = 'X'.
lwa_headdata-forecast_view = 'X'.
lwa_headdata-work_sched_view = 'X'.
lwa_headdata-account_view = 'X'.
lwa_headdata-cost_view = 'X'.
*Client data
CLEAR: lwa_clientdata, lwa_clientdatax.
IF it_rpt-werks EQ c_1251.
lwa_clientdata-matl_group = it_rpt-matkl.
lwa_clientdata-old_mat_no = it_rpt-bismt.
lwa_clientdata-base_uom = it_rpt-meins.
lwa_clientdata-manu_mat = it_rpt-mfrpn.
lwa_clientdata-mfr_no = it_rpt-mfrnr.
ENDIF.
lwa_clientdata-division = it_rpt-spart.
lwa_clientdata-unit_of_wt = lc_gewei.
lwa_clientdata-trans_grp = lc_tragr.
IF it_rpt-werks EQ c_1251.
lwa_clientdatax-matl_group = 'X'.
lwa_clientdatax-old_mat_no = 'X'.
lwa_clientdatax-base_uom = 'X'.
lwa_clientdatax-manu_mat = 'X'.
lwa_clientdatax-mfr_no = 'X'.
ENDIF.
lwa_clientdatax-unit_of_wt = 'X'.
lwa_clientdatax-trans_grp = 'X'.
lwa_clientdatax-division = 'X'.
Material Description
IF it_rpt-werks EQ c_1251.
lt_matdesc-langu = sy-langu.
lt_matdesc-matl_desc = it_rpt-maktx.
APPEND lt_matdesc.
ENDIF.
*Plant data
CLEAR lwa_plantdata.
lwa_plantdata-plant = it_rpt-werks.
lwa_plantdata-availcheck = lc_mtvfp.
lwa_plantdata-mrp_type = lc_dismm.
lwa_plantdata-mrp_group = lc_disgr.
lwa_plantdata-auto_p_ord = 'X'.
lwa_plantdata-proc_type = 'F'.
IF it_rpt-werks EQ c_1251.
it_rpt-prctr = lc_prctr. "1252
ELSEIF it_rpt-werks EQ c_1261.
it_rpt-prctr = lc_prctr1. "1262
ENDIF.
lwa_plantdata-profit_ctr = it_rpt-prctr.
lwa_plantdata-period_ind = lc_perkz.
lwa_plantdata-max_stock = it_rpt-stawn.
lwa_plantdata-countryori = it_rpt-herkl.
lwa_plantdata-sloc_exprc = it_rpt-lgfsb.
CLEAR lwa_plantdatax.
lwa_plantdatax-plant = it_rpt-werks.
lwa_plantdatax-availcheck = 'X'.
lwa_plantdatax-mrp_type = 'X'.
lwa_plantdatax-mrp_group = 'X'.
lwa_plantdatax-auto_p_ord = 'X'.
lwa_plantdatax-proc_type = 'X'.
lwa_plantdatax-profit_ctr = 'X'.
lwa_plantdata-period_ind = 'X'.
lwa_plantdatax-max_stock = 'X'.
lwa_plantdatax-countryori = 'X'.
lwa_plantdatax-sloc_exprc = 'X'.
*Valuation data
CLEAR lwa_valuationdata.
lwa_valuationdata-val_area = it_rpt-werks.
lwa_valuationdata-price_ctrl = lc_vprsv.
lwa_valuationdata-price_unit = lc_peinh.
lwa_valuationdata-val_class = it_rpt-bklas.
CLEAR lwa_valuationdatax.
lwa_valuationdatax-val_area = it_rpt-werks.
lwa_valuationdatax-price_ctrl = 'X'.
lwa_valuationdatax-price_unit = 'X'.
lwa_valuationdatax-val_class = 'X'.
*Storage location
CLEAR lwa_storagelocation.
lwa_storagelocation-plant = it_rpt-werks.
lwa_storagelocation-stge_loc = it_rpt-lgort.
CLEAR lwa_storagelocationx.
lwa_storagelocationx-plant = it_rpt-werks.
lwa_storagelocationx-stge_loc = it_rpt-lgort.
*Tax Classifications
IF it_rpt-werks EQ c_1251.
it_rpt-tatyp = lc_tatyp. "u2018MWSTu2019
ELSEIF it_rpt-werks EQ c_1261.
it_rpt-tatyp = lc_tatyp1. "u2018UTXJu2019
ENDIF.
lt_taxclass-tax_type_1 = it_rpt-tatyp.
lt_taxclass-taxclass_1 = lc_taxkm.
lt_taxclass-tax_ind = lc_taxim.
APPEND lt_taxclass.
*Sales data
CLEAR: lwa_salesdata, lwa_salesdatax.
IF it_rpt-werks EQ c_1251.
it_rpt-vkorg = lc_vkorg.
ELSEIF it_rpt-werks EQ c_1261.
it_rpt-vkorg = lc_vkorg1.
ENDIF.
lwa_salesdata-sales_org = it_rpt-vkorg.
lwa_salesdata-distr_chan = lc_vtweg.
lwa_salesdata-cash_disc = lc_sktof.
lwa_salesdata-item_cat = lc_mtpos.
lwa_salesdatax-sales_org = it_rpt-vkorg.
lwa_salesdatax-distr_chan = lc_vtweg.
lwa_salesdatax-cash_disc = 'X'.
lwa_salesdatax-item_cat = 'X'.
*Forecast parameters
CLEAR: lwa_forecast, lwa_forecastx.
lwa_forecast-plant = it_rpt-werks.
lwa_forecast-fore_model = lc_prmod.
lwa_forecast-fore_pds = lc_anzpr.
lwa_forecast-hist_vals = lc_peran.
lwa_forecastx-plant = it_rpt-werks.
lwa_forecastx-fore_model = 'X'.
lwa_forecastx-fore_pds = 'X'.
lwa_forecastx-hist_vals = 'X'.
Purchasing long text
IF it_rpt-werks EQ c_1251.
IF it_rpt-tdline1 <> ' '.
lv_tdobject = 'MATERIAL'.
lv_tdid = 'BEST'.
lv_tdname = it_rpt-matnr.
PERFORM fill_longtext TABLES lt_longtext
USING lv_tdobject
lv_tdname
lv_tdid
sy-langu
it_rpt-tdline1.
ENDIF.
Basic long text
IF it_rpt-tdline2 <> ' '.
lv_tdobject = 'MATERIAL'.
lv_tdid = 'GRUN'.
lv_tdname = it_rpt-matnr.
PERFORM fill_longtext TABLES lt_longtext
USING lv_tdobject
lv_tdname
lv_tdid
sy-langu
it_rpt-tdline2.
ENDIF.
*Units of measure
CLEAR : lt_uom,lt_uomx.
lt_uom-alt_unit = it_rpt-meins.
lt_uom-alt_unit_iso = it_rpt-meins.
lt_uom-unit_of_wt = it_rpt-gewei.
APPEND lt_uom.
lt_uomx-alt_unit = it_rpt-meins.
lt_uomx-alt_unit_iso = it_rpt-meins.
lt_uomx-unit_of_wt = 'X'.
APPEND lt_uomx.
ENDIF.
CALL FUNCTION 'BAPI_MATERIAL_SAVEDATA'
EXPORTING
headdata = lwa_headdata
clientdata = lwa_clientdata
clientdatax = lwa_clientdatax
plantdata = lwa_plantdata
plantdatax = lwa_plantdatax
forecastparameters = lwa_forecast
forecastparametersx = lwa_forecastx
storagelocationdata = lwa_storagelocation
storagelocationdatax = lwa_storagelocationx
valuationdata = lwa_valuationdata
valuationdatax = lwa_valuationdatax
salesdata = lwa_salesdata
salesdatax = lwa_salesdatax
IMPORTING
return = lwa_return
TABLES
materialdescription = lt_matdesc
unitsofmeasure = lt_uom
unitsofmeasurex = lt_uomx
materiallongtext = lt_longtext
taxclassifications = lt_taxclass
returnmessages = it_messages.
Regards,
ReddyCan you check with below code .
CALL FUNCTION 'CONVERSION_EXIT_MATN1_INPUT'
EXPORTING
INPUT = it_rpt-matnr
IMPORTING
OUTPUT = it_rpt-matnr
EXCEPTIONS
LENGTH_ERROR = 1
OTHERS = 2.
IF SY-SUBRC <> 0.
* MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
* WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
Move it_rpt-matnr to lwa_headdata-material .
Regard's
Smruti -
Re-Installtion of Issue with iMac (circa 2009) - disk has been reformatted
imac circa 2008 /2009 - I have downloaded maverics and have it on a usb drive that has been reformatted GUID.
the imac disk has been reformatted GUID
Startup manager is not showing up?
(earlier tried MC OS Show Leopard instal disk - that would hot load to install screen)
How do I get MAC os back onto this imac please?Thank you Eric for engaging:
Both the USB and the Internal Drives have been formatted GUID and OS Extended (journaled) (but I'm going to go through the process again so there cannot be any question)
When I use (option) Start up manager - the USB drive is NOT being presented as an option. Only the DVD Show Leopard - when I pursue that option it takes it's time and then I eventually get that MultiLanguage White text on dark rectangle in the centre of the screen - forcing you to crash out. (it does not launch the disk at all)
The USB drive is a WD Elements 2GB - but it does NOT have it's own power source - might that be an issue?
I will also repair permission on both drives -
What is going on here. I've waited 4 weeks for my ipad which will not do anything untill I've downloaded the latest version of itunes which I can't do because this message keeps appearing,
Our apologies but there was an unexpected error with the application.
This problem has been noted, and an email has been sent to the administrators.
Please check back in a few hours to try the download again.
Reading another post, someone is still trying after two days!
Anyone got a solution to this please, or, if not, does anyone know how to email itunes.
Thanks, AllanFound this
http://www.v3.co.uk/v3-uk/download-review/1955243/apple-itunes-1011
Hope it helps -
hello,i have updated to the new 11,and now i tunes will not open,error pops up,says Data Execution Prevention,and other error we can not complete ur i tune request,unknown error 4002,i have uninstalled and reinstalled ,has been no help.
- Try restoring on another computer.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
Trying to access an epub book downloaded from local public library on my PC laptop with windows 8.1. I keep getting Error!Check Activation. My ID has been authorized, how do I fix this?
Trying to access an epub book downloaded from local public library on my PC laptop with windows 8.1. I keep getting Error!Check Activation. My ID has been authorized, how do I fix this?
Maybe you are looking for
-
ITunes Store not working on Windows 8.1
I upgraded my laptop to Windows 8.1 from Windows 8. iTunes works fine as in the music plays etc. But when I click on 'iTunes Store', it doesn't load and says that iTunes has stopped working. Can someone please find a solution to this problem ASAP. Th
-
Is there a way to pass data between 2 seperate programs?
I realize you can pass values to a program on boot but is there a way to pass information to a program after it's loaded? I want to make it so two seperate programs running on the same PC could exchange data back and forth. Where one program can call
-
Sales order confirmation form in Adobe Forms-Urgent
Hi Experts, I have to create an adobe form for Sales order Confirmation. I have worked on ABAP but no idea about Adobe forms. I am new for this. Could you please tell me what are are the things required to delelop an adobe forms What are the steps i
-
Hi, I have a problem with my itunes account. My girlfriend bought me my ipod and put it under her account. I recently got a new computer and tried listening to songs and such but she already has her account authorized on 5 computers. However, what I
-
My first IPod and I don't know what to do
Just got an iPod nano, and need some help,thanks in advance for any help you can give. Now onto my problem,when I plug my nano into my PC it appears as a removeable disk in the My Computer file, I open up the removeable file and four folders appear.