Error Installing RAC11gR2 on AIX
Hi
I am installing RAC11gR2 on AIX. when the ASM instance is going to be created on the node 2, there is an error related the devices where the ASM is going to be located. The name devices are different in each node. In node 1. The devices for the RAC are hdisk3, hdisk10 & hdisk11. On the node 2 the disk devices are: hdisk3, hdisk4 & hdisk5.
Node 1
# lsdev -Ccdisk
hdisk0 Available 2d-08-00-8,0 16 Bit LVD SCSI Disk Drive
hdisk1 Available 2d-08-00-9,0 16 Bit LVD SCSI Disk Drive
hdisk2 Available 2d-08-00-10,0 16 Bit LVD SCSI Disk Drive
hdisk3 Available 1D-08-02 MPIO Other FC SCSI Disk Drive
hdisk4 Defined 1n-08-02 MPIO Other FC SCSI Disk Drive
hdisk5 Defined 11-08-02 MPIO Other FC SCSI Disk Drive
hdisk6 Defined 2R-08-02 MPIO Other FC SCSI Disk Drive
hdisk7 Defined 25-08-00-8,0 16 Bit LVD SCSI Disk Drive
hdisk8 Defined 25-08-00-9,0 16 Bit LVD SCSI Disk Drive
hdisk9 Defined 25-08-00-10,0 16 Bit LVD SCSI Disk Drive
hdisk10 Available 1D-08-02 MPIO Other FC SCSI Disk Drive
hdisk11 Available 1D-08-02 MPIO Other FC SCSI Disk Drive
Node 2
# lsdev -Ccdisk
hdisk0 Available 25-08-00-8,0 16 Bit LVD SCSI Disk Drive
hdisk1 Available 25-08-00-9,0 16 Bit LVD SCSI Disk Drive
hdisk2 Available 25-08-00-10,0 16 Bit LVD SCSI Disk Drive
hdisk3 Available 1n-08-02 MPIO Other FC SCSI Disk Drive
hdisk4 Available 1n-08-02 MPIO Other FC SCSI Disk Drive
hdisk5 Available 1n-08-02 MPIO Other FC SCSI Disk Drive
I have got an error creating the ASM on the node 2.
The question is: all the devices has to be the same name on both nodes ?
Thanks
Hi Dude
I am carrying out an installation on a server where RAC was installed. I uninstall all but the raw devices has still information of the past ASM files... etc. I need to format these partitions for having the initial condiction for the new fresh installation. Do you have the commands or any article or link to do that ?
I am on AIX.
Thanks
Similar Messages
-
Error installing ECC6 on AIX 6.1
i am installing ECC6 on AIX 6.1, when i run sapint it gives me error:
iauxsysex.c:318: child /tmp/sapinst_exe.209324.1256978362/sapinst (pid 266368) has crashed. Executable directory is /tmp/sapinst_exe.209324.1256978362. Contact Support.
iaextract.c:895: child has signaled an exec error. Keeping directory /tmp/sapinst_exe.209324.1256978362
I am executing it by user rootHi,
Please verify that you are using the latest sapinst patch as per note 929929.
Also check that your userlimits are set to unlimited, expecially for DATA ,STACK ,CORE and MEMORY
Best regards,
Warren -
Error in installing CCB on AIX
Hello,
I am trying to install CCB on AIX .Getting error while installling the Framework. Seek support on this
Environment Configuration CCB1DEMO
1. Environment Description
Environment Description: CCB1DEMO
2. Business App Server Configuration
Business Server Host: dstindiap05
JVM Child process starting Port Number: 6503
Number of JVM Child processes: 2
Bootstrap port: 2814
WebSphere Server Name: DEMO
WebSphere Application Name: SPLService
WebSphere Deployment userid: cissys
WebSphere Deployment password: cissys
3. Web Server Configuration
Web Server Host: dstindiap05
Web Server Port Number: 6500
WebSphere Server Name: DEMO
WebSphere Application Name: SPLWeb
WebSphere Deployment userid: cissys
WebSphere Deployment password: cissys
Is this environment will be used for development: false
Deploy appViewer module to the Web Server: true
Exploded directory (true) or archive format (false): false
Preload All Pages on startup: false
Maximum age of a cache entry for text (s): 28800
Maximum age of a cache entry for images (s): 28800
To switch to basic Login Page enter: BASIC: FORM
Application Admin Userid : SYSUSER
Application Admin Userid Password: sysuser00
4. Database Configuration
USERID of the User of the Database: cisadm
Password of the User of the Database: CISADM
Oracle Database Name: CCB1DEMO
Oracle Client Character Set NLS_LANG: AMERICAN_AMERICA.UTF8
Host name of database server: dstindiap05
Port name for database connection: 1521
5. Environment Configuration
MPL Admin Port: 6502
MPL Automatic startup: N
XAI Startup "wait" time seconds: 90
JVM Child Memory Allocation: 512
Batch Server Enabled: true
Batch Threads Number: 5
Batch Scheduler Daemon: true
P. Write Configuration File
X. Exit (without save)
Each item in the above list should be configured for a successful install.
Choose option to configure or (P) to process or confirm configuration: P
Configuration file /opt/spl/ccb/CCB1DEMO/etc/ENVIRON.INI is created.
Execute splenviron.sh -e CCB1DEMO to setup environment variables.
Error - No license key detected. Application Server requires
a license key in order to execute.
Please refer to your application supplier.
Version ................ (SPLVERSION) : V2.2.0
Database Type ............... (SPLDB) : oracle
ORACLE_SID ............. (ORACLE_SID) : CCB1DEMO
NLS_LANG ................. (NLS_LANG) : AMERICAN_AMERICA.UTF8
Environment Name ....... (SPLENVIRON) : CCB1DEMO
Environment Code Directory (SPLEBASE) : /opt/spl/ccb/CCB1DEMO
App Output Dir - Logs ... (SPLOUTPUT) : /opt/spl/ccb/sploutput/CCB1DEMO
Build Directory .......... (SPLBUILD) : /opt/spl/ccb/CCB1DEMO/cobol/build
Runtime Directory .......... (SPLRUN) : /opt/spl/ccb/CCB1DEMO/runtime
100203.02:22:58 <info> Template generation step.
100203:022303 <info> No value is set for optional parameter DOC1HOSTDIR, ignoring it.
100203:022304 <info> No value is set for optional parameter DOC1HOSTDIR, ignoring it.
100203.02:23:04 <info> FW template generation step.
100203.02:23:04 <info> /opt/spl/ccb/CCB1DEMO/bin/genwasstubs.sh : Generate Stubs Started Wed Feb 3 02:23:04 CST 2010
100203.02:23:04 <info> Environment CCB1DEMO
100203.02:23:04 <info> Build servicebean jar
Buildfile: /opt/spl/ccb/CCB1DEMO/etc/jarservice.xml
Thanks and Regards
Amityes i have already installed the temporary licenses.
and nothing changes.
i recreate the microfocus database (with aslmdbrecover) and nothing changes.
i´m still getting the same error .
Thx.
Diego -
FRM-92102: A network error has occured [IBM AIX 5.3]
Hi All,
I have deployed my oracle forms application on Oracle 10g(10.1.2.0.2) Application Server installed on IBM AIX 5.3 Server. Forms developed on Developer Suite 10g.
When I login to the application and start working, The FRM-92102 Error pops up and I have to quit, without any other option
Soon, when I check the opmnctl status, I see OC4J_BI_Forms moved into "init" state. After sometime the state gets into "Alive”. Then i run my application again only to get the same pop again.
The pop up occurs randomly. Neither specific form nor operation invokes it! I don’t know why the Status of OC4J_BI_Forms suddenly gets into "init" state? Since it’s in "init" state the Application is loosing a connection to forms service and popping up the above error.
Pls find the detailed logs in below link
http://www.mediafire.com/?ywnyid4xhr5
I have a dead line to meet in Next weekend. Any help is highly appreciated.
Humble Regards,
SAMHi All,
I resolved this by editing opmn.xml file.
Change
<data id="/reports/rwservlet/pingserver?start=auto" value="20000"/>
to
<data id="/reports/rwservlet/" value="20000"/>
Regards,
SAM -
Hello,
I am trying to install an add-on package lme4 into the R distribution and got the following error:
* installing to library '/usr/lib/R/library'
* installing *source* package 'lme4' ...
** package 'lme4' successfully unpacked and MD5 sums checked
** libs
/systemr/port/AIX/comp/oraxlc.shx -F/systemr/port/AIX/comp/xlc.cfg -I/usr/lib/R/include -DNDEBUG -I/systemr/port/AIX/include -I/opt/freeware/include -I/usr/linux/include -I/usr/local/include -I/usr/lpp/X11/include/X11 -I"/usr/lib/R/library/Matrix/include" -I"/usr/lib/R/library/stats/include" -O -qstrict -qnoldbl128 -c init.c -o init.o
/bin/sh: /systemr/port/AIX/comp/oraxlc.shx: not found.
make: 1254-004 The error code from the last command is 127.
The command I am using is:
R CMD INSTALL lme4_0.999999-2.tar.gz
I am pretty sure that the server does not have XLC installed; neither does the directory /systemr. The compiler I have is gcc. I tried to set the environment variable CC to the right gcc value but R keeps getting me the same problem. Is there a way in R to specify the compiler?
Any help is highly appreciated.The trick worked ... Now R can find gcc as the compiler. Many thanks!
I also found that the configuration file for package installation is Makeconf under /usr/lib/R/etc. It seems to me that people can modify that file to use the right compiler/compiler options.
Version of R distribution package: 2.15.2
Version of AIX: 6
Hope this helps -
Error installing tuxedo12.1.1 32-bit on AIX7.1
I'm getting this error installing Tuxedo12.1.1 on AIX
I'm logged in via XTerm to AIX machine. (Used same method/login as when i installed Oracle12c DB client)
Is "oui/instImages/images.properties" Not part of my Oracle database install?
can I copy file from Oracle11.1 or does it need to be installed?
$ cd install
$ ls
addLangs.sh oneclick.properties runInstaller
attachHome.sh oraparam.ini runSSHSetup.sh
clusterparam.ini oraparam.ini.orig unzip
detachHome.sh oraparamsilent.ini
lsnodes resource
$ ./runInstaller
Starting Oracle Universal Installer...
Checking swap space: must be greater than 500 MB. Actual 4096 MB Passed
Checking monitor: must be configured to display at least 256 colors. Actual 256 Passed
Preparing to launch Oracle Universal Installer from /tmp/OraInstall2014-12-15_11-29-23AM. Please wait ...$ Oracle Universal Installer, Version 12.1.0.1.0 Production
Copyright (C) 1999, 2013, Oracle. All rights reserved.
java.io.FileNotFoundException: /tmp/OraInstall2014-12-15_11-29-23AM/oui/instImages/images.properties (No such file or directory)
at java.io.FileInputStream.<init>(FileInputStream.java:137)
at java.io.FileInputStream.<init>(FileInputStream.java:96)
at oracle.sysman.oii.oiif.oiifm.OiifmSplashScreen.loadProperties(OiifmSp
lashScreen.java:490)
at oracle.sysman.oii.oiif.oiifm.OiifmSplashScreen.<clinit>(OiifmSplashSc
reen.java:95)
at java.lang.J9VMInternals.initializeImpl(Native Method)
at java.lang.J9VMInternals.initialize(J9VMInternals.java:200)
at oracle.sysman.oii.oiif.oiifm.OiifmGraphicInterfaceManager.<init>(Oiif
mGraphicInterfaceManager.java:280)
at java.lang.J9VMInternals.newInstanceImpl(Native Method)
at java.lang.Class.newInstance(Class.java:1474)Well...seems some time now, but here goes :
Firstly, your installation should work with the free MS VC++ Express Edition which is free, at least mine did.
Secondly, there is NO Free / Trial version of MKS Developers (as I think its called now) or ToolKit (as widely known), but there is a bit of good news, there is an alternative now in Cygwin which is free, and you can download this at http://www.cygwin.com , however, you have to read the Metalink document regarding this, as the installation of all its component is not advised, so you have to know the right utilities to include as options during installation
Thirdly, if you attempt staging with the adautostage.pl ( The perl script for staging an area for the installation files) it does not matter which you unzip first. This script arranges the installation folders as intended by Oracle.
If you have further queries, let us know.
Good Luck -
ERROR INSTALLING OC4J CONFIGURATION FILES
Hi,
Steps:
1. Downloaded Oracle11g Rel2 from download.oracle
2.Installed Software only option and completed installation on my laptop Windows7 ultimate. Selected Enterprise Version, unchecked OLAP,DATA MINING.
Error message during installation, some files missing .jar files. I have opted to ignore and continue and finally got success installation message.
3.Configured DB using DBCA.
4.Able to connect as SYS, SYSTEM.
Problem.
I tried to reconfigure DB using DBCA for OEM, received the msg
ERROR INSTALLING OC4J CONFIGURATION FILES. The summary error log is here. Appreciate any help.
java.io.FileNotFoundException: C:\app\Administrator\product\11.2.0\dbhome_1\oc4j\j2ee\OC4J_DBConsole\config\jms.xml (The system cannot find the file specified)
java.io.FileNotFoundException: C:\app\Administrator\product\11.2.0\dbhome_1\oc4j\j2ee\OC4J_DBConsole\config\rmi.xml (The system cannot find the file specified)
CONFIG: Could not find or correctly parse file C:\app\Administrator\product\11.2.0\dbhome_1\oc4j\j2ee\OC4J_DBConsole\config\http-web-site.xml in searching for tag web-site with attribute port
java.io.FileNotFoundException: C:\app\Administrator\product\11.2.0\dbhome_1\oc4j\j2ee\OC4J_DBConsole\config\http-web-site.xml (The system cannot find the file specified)
java.io.FileNotFoundException: C:\app\Administrator\product\11.2.0\dbhome_1\oc4j\j2ee\OC4J_DBConsole\config\server.xml (The system cannot find the file specified)
Mar 8, 2014 9:15:42 AM oracle.sysman.emcp.EMDBCConfig instantiateOC4JConfigFiles
CONFIG: Failed to set value in server.xml for application-server tag
Mar 8, 2014 9:15:42 AM oracle.sysman.emcp.EMConfig perform
oracle.sysman.emcp.exception.EMConfigException: Error instantiating OC4J configuration files
CONFIG: Could not find or correctly parse file C:\app\Administrator\product\11.2.0\dbhome_1\oc4j\j2ee\OC4J_DBConsole\config\jms.xml in searching for tag jms-server with attribute port
java.io.FileNotFoundException: C:\app\Administrator\product\11.2.0\dbhome_1\oc4j\j2ee\OC4J_DBConsole\config\jms.xml (The system cannot find the file specified)
CONFIG: Could not find or correctly parse file C:\app\Administrator\product\11.2.0\dbhome_1\oc4j\j2ee\OC4J_DBConsole\config\rmi.xml in searching for tag rmi-server with attribute port
thanks
RamHi,
Seems you have not extracted downloaded zip files into same directory. In that case you get error like
java.io.FileNotFoundException:
/Disk2/database/stage/Components/oracle.rsf.hybrid/11.1.0.6.0/1/DataFiles/filegroup12.jar (A file or directory in the path name does not exist.)
java.io.FileNotFoundException:
/Disk2/database/stage/Components/oracle.rsf.hybrid/11.1.0.6.0/1/DataFiles/filegroup5.jar (A file or directory in the path name does not exist.)
Also after installation dbca will throw error.
Try the below
For AIX platform:
unzip in the same folder
$ mkdir 1120
$ mv aix.ppc64_11g_database_1of2.zip 1120
$ mv aix.ppc64_11g_database_2of2.zip 1120
$ cd 1120
$ unzip aix.ppc64_11g_database_1of2.zip
$ unzip aix.ppc64_11g_database_2of2.zip
$ cd database
$ ./runInstaller
This is true for all platforms on which you get two .zip files to download
For Windows 64 bit example on 11.2.0.1 you can do the following :
- create a directory C:\tmp\1120
- copy winx64_11g_database_1of2.zip and winx64_11g_database_2of2.zip under C:\tmp\1120
- unzip winx64_11g_database_1of2.zip and winx64_11g_database_2of2.zipunder C:\tmp\1120
Thanks,
Krishna -
Error installing Adobe Flash 11 "launchfail" after enable AppLocker
Error installing Adobe Flash 11 "launchfail" after enable AppLocker please help. I have allow everyone from publisher for .exe and .msi
I'll ask around, but I don't have any experience with AppLocker. Have you gone through all of the documentation here?
http://technet.microsoft.com/en-us/library/dd723678(v=ws.10).aspx -
When trying to update my CC apps, the update fails. I get this error: Update Failed. There was an error installing this update. Please try again later or connect customer support. This is currently happening for InDesign, Photoshop and Bridge. I had this problem previous and was able to fix by doing a complete wipe of my computer and reinstalling CC. However, I should not have to wipe my computer clean everytime I need to do a CC update. HELP!
Hi,
Please download the updates directly from the link below:
WIN: All Adobe CC 2014 Updates: The Direct Download Links for Windows | ProDesignTools
MAC: All Adobe CC 2014 Updates: The Direct Download Links for Mac OS | ProDesignTools
Regards,
Sheena -
I have not been able to reinstall Acrobat Pro on my laptop. I have Suite 6 Design & Web Premium on my HP laptop. I have Windows 7 operating system. All of a sudden Acrobat Pro will not open so I uninstalled and tried to reinstall the program.
The error messages I get are:
ERROR: Error 2203.Database: C:\Windows\Installer\12102c.ipi. Cannot open database file. System error -2147287035.
ERROR: Install MSI payload failed with error: 1603 - Fatal error during installation.
MSI Error message: Error 2203.atabase: C:\Windows\Installer\12102c.ipi. Cannot open database file. System error - 2147287035.
ERROR: Third party payload installer AcroPro.msi failed with exit code: 1603
Help PLEASE!Hi Patricia ,
For error 2203 ,please refer to the following link.
https://helpx.adobe.com/creative-suite/kb/error-2203-install-creative-suite.html
For error 1603 ,refer to this link.
https://helpx.adobe.com/creative-suite/kb/error-1603-install-cs3-cs4.html
Let us know if this solves the issue .If required ,we"ll surely assist you further.
Regards
Sukrit Dhingra -
Error: installing Java Add-in for Central instance
Dear experts,
i've installed the SCS and the Java Add-in for DB successful. While trying to install the java add-in for the central instance i get the following error:
An error occurred while processing service SAP NetWeaver 7.0 Support Release 3 > Software Life-Cycle Options > Java Add-In for ABAP > MaxDB > Central System > Central Instance Java Add-In ( Last error reported by the step :TypeError: instance has no properties (in script NW_Addin_CI|ind|ind|ind|ind, line 109346: ???)
Thanks in advance.
DanielHi,
Check below thread:
Error installing SAP NetWeaver 2004s Java Trial Version (SP9)
Thanks
Sunny -
Steve Jobs obviously was "the man" because every update or install now gives me problems... i can no longer download anything to my iphone.. giving me errors of "cannot install at this time" and i get an error installing itunes on my other laptop... wth is going on!??!
ok so the download problem with my iphone.. what could be the cause of that? ive restarted and deleted the "undownloaded app" over 10 times already. and restarted the iphone 10 times... next thing i know i cant install itunes on my laptop.... geez man..
obviously there is a fix which someone will help... but why should i have to go through all that crap to install a so called uncomplicated software... when you think about it this really shouldnt even be an issue.
normally if the thing dosent work. normally with most programs you just uninstall the uncompleted software and just reinstall and everything is usually good to go.. help!ive never had any problems with ap[ple products in the past... this is a first and a stupid problem if you ask me
-
unable to update itunes. help. error message when trying to update to latest version of itunes. "the installer has encountered an unexpected error installing this package. this may indicate a problem with this package. error code 2721"
Hello chae84swangin,
I recommend following the steps in the article below when getting an error message trying to install iTunes:
Trouble installing iTunes or QuickTime for Windows
http://support.apple.com/kb/HT1926
Thank you for using Apple Support Communities.
Best,
Sheila M. -
I tried updating iTunes to version 11.1.1, but installation fails each time even when I did it manually as was suggested. The message I receive is: "The installer has encountered an unexpected error installing this package. This may indicate a problem with this package. The error code is 2324."
Hi hongkongpom,
Just wanted to say that after posting the problem, I had a chat with an iTunes' Tech Support, her name is Rebekah. My problem was resolved after that. Will list the chat history below in hopes that it may help you as well.
Good luck!
Samia
Chat Transcript
Friday, October 4, 2013 05:55 AM
Duration: 81 minutes 28 seconds
Rebekah:
Welcome to AppleCare chat support. Please give me a moment to look over your information.
Rebekah:
Hi, Samia! My name is Rebekah. If we get disconnected, please chat us back. http://www.apple.com/support/ipod/contactEnter the case number from the initial email we sent you. This gives the next advisor you chat with immediate access to your case history.
Rebekah:
Could you please confirm your serial number? I want to be sure we provide the best service possible for you, Samia!
SAMIA:
Sure, it's 8L8395UY2C5
SAMIA:
My problem is with iTunes.
Rebekah:
Thanks for that confirmation. Just a heads up, this is iOS Tech Support. We do support iPod touches, iPads, and iPhones, but not the iPod classic. But no worries! I can get you in touch with a phone Advisor who can get you in touch with the department that specializes in iPod classics and would be able to better assist you. Would that be OK?
SAMIA:
I wasn't able to install the new version of iTunes (version 11.1.1). The installation keeps failing. The they suggested the I install it manually and that failed too. I will attach the message I received.
SAMIA:
I don't have a problem with iPod.
SAMIA:
Just iTunes
Rebekah:
No problem! We can certainly troubleshoot iTunes as much as possible. It may come to the point that you may have to transferred, but we can do as much as possible during this chat!
Rebekah:
Thanks for the screenshot. It is a bit small so I am unable to fully see the message that you are receiving. What is the error message you are receiving?
SAMIA:
This is the message I received in case you weren't able to open the attachment: "The installer has encountered an unexpected error installing this package. This may indicate a problem with this package. The error code is 2324."
Rebekah:
Thanks for that info!
SAMIA:
Pleasure!
Rebekah:
What version of Windows (XP, Vista, 7) do you have?
SAMIA:
Windows 7
SAMIA:
Windows 7 Home Premium
Rebekah:
Thanks for that confirmation. I do apologize for the delay, Samia. I am researching this error code now. You mentioned trying to install iTunes manually. To be sure I am on the same page, what steps did you take to do that?
SAMIA:
Well when the indsatalltion failed I was given instructions to select Download Only from Tools and then install manually. When I did it, I window popped up with the following items: - AppleApplicationSupport
SAMIA:
- AppleMobileDeviceSupport64
SAMIA:
- Bonjour64
SAMIA:
iTunes64
SAMIA:
SetupAdmin
SAMIA:
I selected Repair in all of them instead of Remove and all worked but iTunes64
SAMIA:
That's when I received the message that I sent you earlier.
SAMIA:
By the way, this is the fir st time something like this occured. I never had problems with installation before.
Rebekah:
I completely understand what you're saying. Since that Repair did not resolve the issue, our best option is to uninstall iTunes and its components and redownload it. To do this, we will follow the steps in this article: Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
Rebekah:
First, we will want to quit iTunes and/or Apple Software Update if those are open at this time.
SAMIA:
Rebekah, the instructions you gave says, "For Windows XP, follow these steps to remove and reinstall iTunes and other software components for Windows XP."
SAMIA:
I closed all applications
SAMIA:
Also, my iTunes doesn't open anymore after the new failed installation.
Rebekah:
The section that says "For Windows XP…" is in case we opened up the wrong article, as we have the one for Windows Vista, 7, or 8. There is a link to click ("these steps") in those directions that would take us to the article for uninstalling on a Windows XP.
Rebekah:
So no worries! We have the right article!
Rebekah:
On the computer, we will want to click on Start > Control Panel. In Control Panel, we will click the "Uninstall a program" link.
SAMIA:
I thought so after doing a little exploration.
SAMIA:
done
Rebekah:
Alright, we'll want to select iTunes from the list of currently installed programs. Then we will click Uninstall. When asked if you would like to remove iTunes, let's click Yes.
Rebekah:
After the uninstallation is complete, we don't want to restart your computer if you're prompted.
SAMIA:
Done
Rebekah:
Then if you see other iTunes entries on the list, we'll want to remove them the same way.
Rebekah:
Then we will remove all instances of Apple Software Update the same way you removed iTunes.
SAMIA:
Okay, but do I have to remoce iCloud as well?
SAMIA:
Rebekah, I received the same error message again when uninstalling
Rebekah:
We actually do not need to remove iCloud. After the Apple Software Update, we will want to remove all instances of Apple Mobile Device Support
Rebekah:
How strange! Are you able to click past that and allow the process to continue or has it stopped it completely?
SAMIA:
I am unable to uninstall iTunes either
SAMIA:
Stopped completely
SAMIA:
I treied clicking Repair
Rebekah:
Alright, after trying the Repair option, let's see if it will allow us to continue uninstalling or not.
SAMIA:
I tried that but unfortunately, it isn't working. I still get that same message with error code 2324.
Rebekah:
This error code is not something that I am finding in my sources, Samia. So there is a chance that it is being caused with the Windows computer itself. However, I did find a link that may be able to help with uninstalling iTunes from Windows' support site: http://support.microsoft.com/mats/Program_Install_and_Uninstall
SAMIA:
Rebekah, you're a genius! It worked! iTunes is no longer there. What next?
Rebekah:
Awesome! I'm glad that worked!
Rebekah:
To be sure I am on the same page, what was the last component we uninstalled?
SAMIA:
iTunes
SAMIA:
Shall I remove the Apple Application Support, Apple Mobile Device Support, and Apple Software Update
Rebekah:
That is correct! However, we do want to uninstall it in the order I mentioned above. So Apple Software Update first, Apple Mobile Device Support next, and then Apple Mobile Device Support.
SAMIA:
Got it, but is the second one to uninstall Apple Mobile Device Support OR Apple pplication Support?
Rebekah:
The second one is Apple Mobile Device Support.
Rebekah:
The Application Support will be the last component we uninstall.
SAMIA:
Thanks! I'm on it.
SAMIA:
Done! ll 3 are gone, well 4 with iTunes. Now what?
Rebekah:
Awesome! Also, I just noticed that I accidentally typed Apple Mobile Device Support twice, I do apologize for any confusion! Now we will remove all instances of Bonjour and then remove all instances of Apple Application Support.
SAMIA:
There was only 1 instance with Bonjour. I don't know what the instances are for Apple Application Support
Rebekah:
Yes, Bonjour is often only listed once. Is the Apple Application Support listed at all?
SAMIA:
No
SAMIA:
Since I removed it
Rebekah:
Oh, perfect! If it was removed, we should be set!
Rebekah:
We have removed iTunes and its components now! From here, our next step is to restart the computer. Then once you reboot, you can redownload iTunes from apple.com/itunes
Rebekah:
That should allow you to download iTunes!
SAMIA:
Shall I downloaad the latest vesion?
Rebekah:
You will want to first restart the computer as shown in the article. That will ensure that this process goes smoothly and that everything was removed correctly! Then you can try downloading iTunes again.
SAMIA:
Okay, thanks Rebekah!
Rebekah:
You're very welcome! I'm glad I could help! And of course if you have any issue after the reboot and download, you can always chat us back, as chat is open 24 hours! You will just need to give your case number and the next Advisor would have all my notes!
SAMIA:
Thanks again for all your help, for I couldn't have managed with out it. Have a nice day!
Rebekah:
You're very welcome! I know how important iTunes is and I'm glad we could get you on a path to resolution!
Rebekah:
I hope you have a lovely day!
Rebekah:
It's been a pleasure speaking with you! Thanks for chatting with us Samia. If you don't have any more questions, select End Chat from the upper left corner of the chat window.
SAMIA:
Will do, thanks. -
"Windows found driver software for your device but encountered an error installing"
I've spent hours researching this error - Seems like many people have the same issue although there is no difinitive fix or known cause.
I'm hoping someone here has an answer.
Windows 7 Home Premium x64 OEM (HP)
This is not an upgraded Vista system.
It's not a specific driver related issue as it's the same response/effect be it graphics/chip set/usb/printer drivers.
Please dont suggest to flatten and re-install or run a repair install - It's not an option, I only have remote access to the unit
as it's currently in field use.
This is a machine specific issue - identical machine purchased at the same time and configured the same has no issue.
So the story.
User has been fine for weeks - no hardware of software changes except Windows Updates.
A Camera/USB connection that was working no longer does.
Tried in all USB ports
Plug in - windows announces found new hardware, tries to install drivers then fails
with "Windows found software for your device but encountered an error installing ...."
Device manager finds and identifies device although it is in the 'Unknown Device" category.
Manually updating drivers via search/internet or point directly at a driver has exactly the same effect.
Thinking this was just the camera drivers - I researched and downloaded new drivers from camera manufacturers sites
Fuji and Canon.
Same effect.
Deleted/uninstalled drivers completely, deleted/uninstalled all USB root hub and USB devices (hidden and visible)
SFC /Scannow finds no error
Cold boot finds USB and chipset(?) devices on boot attempts to reinstall then we get
"Windows found driver software for your device but encountered an error installing"
So now I have no usb devices at all - memory stick/card reader/printer...... nada.
in fact if I try to update any device driver I get the same message generated.
Restore point does not help either.
After much trawling I found reference to a permisions issue and stale driver cache data.
(This is using an administrator account - not user with admin permissions?)
I'm willing to try anything at this time
I deleted the infcache.1 and other .dat files under c:\windows\system32\driverstore
Copied the usb .inf and .pnf from the appropriate FileRepository directory into c:\windows\inf
Uninstalled all the usb/unkown devices from device manager again.
Rebooted
Takes a little longer to boot as I take it it's rebuilding the driver cache then
a very short hurrah!!!
I can now use usb memory card and pen drives - no issue
Plug in a camera or printer...
"Windows found driver software for your device but encountered an error installing"
Several attempt at this trying different driver versions.
It should not be vendor specific, the other field machine that works is using Microsoft drivers for these devices.
I even copied the drivers from one machine to the other - repeated everything above...
"Windows found driver software for your device but encountered an error installing"
And then the nail in my sanity
Try windows update....
Reboot
"Windows found driver software for your device but encountered an error installing"
but this time its different.
The device it thinks it cannot install is the generic MTP-PTP drivers (Photo Transfer Protocol -so am I getting somewhere)
so it still finds but cannot install.
The cameras are always found but appear as 'unknown devices' and cannot be accessed
Uninstall all USB/unkown again - reboot..
Same message and this time I've lost all the USB again.
Restore point to before Win Update gets me USB back again although I still have no cameras - so theres an update issue as well.
This has to be tied down to a file access/ registry problem although I'm loath to go cutting about without some guidance.
I'm no great believer in 'registry cleaners' unless anyone can point to a definitive/no ad's/sales version that really works.
As I said above, flattening/rebuild at this time is not an option - the user is not best pleased and I'm completley stumped.
If anyone has experienced(manu of you have) and fixed(still to find one) this issue please let me know how as soon as possible.
ChrisI know I am replying to an old thread - but I have the answer and resolved this error, and since this message comes up first in search results, and part of my answer came from this thread, I wanted to help someone else as this took an extra
12 hours and a lot of technical insight to resolve. See below for detailed explanation that others ask for above.
My original issue was that iTunes didnt reinstall. generating this error that said I am trying to access an unavailable network resource and to browse to find itunes64setup (again). This may partly have been due to me deleting old install version folders.
Research led me to completely uninstall apple products and reinstall per their instruction and fixed the issue with iTunes. see
Remove and reinstall iTunes and related software components for Windows Vista, Windows 7, or Windows 8 - Apple Support
The SAME error I had while updating itunes recurred while uninstalling it from my Windows 7 SP1 system...so I went to microsoft Fixit and attempted to correct and it properly uninstalled iTunes for me, which allowed the reinstall.
What didnt work was my USB web root/ root hub, which partly involved my older system and USB 1.0, and the delete/reinstall existing drivers with the c:\windows\winsxs folder as source of drivers (thank you Magon Liu!!!) which I had to figure out what/why
and how.
Then I had an intel chipset issue...my new Iphone wasn't recognizing in plug and play, and there was an error with installing the device drivers for my new iphone 6. Manual applications didn't work, even though a generic device showed in control panel -
device manager with a yellow !
Per above blog answer - I tried to remove and reinstall my USB controller or update the drivers (I have an Alienware M15 laptop - a few years old.) I discovered that the USB host controller - an Intel(R) 5 Series / 3400 Series Chipset family USB Enhanced
Host controller - (port) was not covered by current Intel chipset programs which are Series 6 and later, but did have an update (8/20/2009 v9.1.1.1020) that supported USB 2.0 (and therefore 3.0 backwards compatibility which as an issue with my new iPhone
and some USB thumb drives.) To find this I had to look at the Support - Downloads and Drivers - browse for drivers and somewhere found an option to look for older no longer supported drivers. I found infinst_autol.exe for my case.
Once downloaded I tried to install and failed. Found the log in C:\Intel\Logs and contains:
[InstallDev]
[Device]
Driver = C:\Users\DAVIDS~1\AppData\Local\Temp\IPMx7\WIN7\ibexusb.inf
INF = C:\Users\DAVIDS~1\AppData\Local\Temp\IPMx7\WIN7\ibexusb.inf
Installed INF =
Previous driver package =
! Warning 0xE0000235: DriverPackageGetPath failed.
Difx = 64 bit
Execute command: C:\Users\DAVIDS~1\AppData\Local\Temp\IPMx7\x64\Difx64.exe -DriverInf "C:\Users\DAVIDS~1\AppData\Local\Temp\IPMx7\WIN7\ibexusb.inf" -Flags 20 -KeyPath "Software\Intel\Difx64"
Using RegDeleteKeyEx
!!! ERROR 0xE0000246: DriverPackageInstall generated an unexpected error
HERE'S THE ADDED EXPLANATION TO BRIAN'S POST THAT EXPLAINS THE SECURITY ISSUE:
This turned out to be an error for two reasons. First, after manually running the command in an "run as administrator" window (same error result), thinking it related to my anti-virus (turned that off/disabled firewall and A/V), and from this thread
granting my user administrative rights to files in an install folder and trying to reinstall inf files and drivers from C:\Windows\winsxs vs my copied infinst_autol.exe expansion (as found from log in C:\Users\David Samuels\AppData\Local\Temp\IPMx7\WIN7 folder).....that
there was an easier solution as the reason this error actually happens is a permissions problem.
To access the proper windows system folders - you have to be the TrustedInstaller service - not just in the administrator group...or you have to be the actual "Administrator" account. To become actual administrator on
your own laptop, Open a command window "run CMD.exe as administrator", then execute command
> net user administrator /active:yes
This creates a local PC Administrator account with no password. Coincidentally it has proper permissions to windows directories for installing drivers. Log in as this user, go to device manager and update the USB hub and any other drivers. if updating the
USB root - it doesn't replace it right away as the system cant disable the currently resident in memory "running" driver - you have to update, then restart the system, log in as administrator and repeat at the next lower layer that has issues.
Once completed - log in as yourself again and disable the administrator account in a command window with > net user administrator /active:no
This in my case enabled all my USB 2.0 and 3.0 devices on my originally only USB 1.0 laptop and everything else works properly again - I hope this helps many of you to resolve your own issues that were difficult to find and resolve and that got as far as
this thread. Good luck!
Regards,
Dave Samuels
Maybe you are looking for
-
How to find a specific day in a range of dates
Hi ! Can someone help me with this I would like to find if there is a Saturday in a range of dates: ex: OpenDate:2012-01-19 to CurrentDate, should return 2012-01-21 OpenDate 2012-01-23 to CurrentDate, should return null field Thank you
-
80GB Classic not syncing to iTunes 9 on New MacBook Pro
I have owned my new 15" MacBook Pro for one whole week since my previous iBook screen display went out on me a few months ago. Extremely excited about my new purchase I carefully transferred items from an older external hard drive to a new external h
-
Two SAP production systems in a single physical server
Dear All, Is SAP support installing two SAP production systems like SAP ECC 6.0 of one customer and ECC 6.0 with a different SID and instance no. for another customer in a single physical server? Would like to know from the experts is this possible?
-
Can't view mts videos in Photoshop Elements 9
I've been trying to view mts formatted videos on PSE9 with no luck. They imported fine and I can see thumbnails, but when I click on one to view, it opens a window to start playing the video, but the window just freezes. I'm running the trial versi
-
Does BB Pearl 8120 os work on the Pearl 8100?
Hi, I have a t-mobile blackberry pearl 8100 os ver 4.2, I would like to upgrade it to a os 4.5 so I can take advantage of some of the blackberry apps but the only phone I found was a pearl 8120 os ver 4.5 that I downloaded from the t-mobile site will