Error iviscope configure trigger

Good morning,
I have a problem with the Iviscope trigger configuration.
I'm using a PCI-5105 Digitizers/Oscilloscopes to acquire 3 channels simultaneously.
I use IVIscope vi to realize the program.
Channels configuration is ok. But when I want to acquire the signals some problem happen.
on version 1.1 of my program the 3 signals are ok but not at the same time. (frequency 1 kHz, voltage +4V, +1V and +2V)
you can see Front panel v1.1 and diagramme v1.1
I don't understand why the signals are not acquired at the same time ?
so I do a second version using trigger vi. (see diagramme1 v1.2 and diagramme2 v1.2)
in this case the signals are not correct (Front panel v1.2)
here I want to use channel3 to trig the 3 other channels.
and with this version, sometime an error message appear (error message Configure Trigger).
Why the trigger channel doesn't work?
Best regards
Florent
Attachments:
diagramme1 v1.2.JPG ‏117 KB
Front panel v1.1.JPG ‏186 KB
diagramme v1.1.JPG ‏149 KB

the other attach File
Attachments:
error message Configure Trigger.JPG ‏133 KB
diagramme2 v1.2.JPG ‏94 KB
Front panel v1.2.JPG ‏225 KB

Similar Messages

NiScope Configure Trigger Edge sending error to niScope Initiate Acquisition

I'm getting an error from my Trigger off of my scope that keeps failing the program. The error code is -1074135022,
it says
niScope Initiate Acquisition.vi:1<ERR>Attribute or property not supported.
Device: NI_Scope
Property: Trigger Holdoff
Status Code: -200197
I'm using an NI-5133, running Labview 2011 and scope 3.9.4
Thank you for you help!
Wolley
Attachments:
Test2.vi ‏69 KB

Upon doing so, I now have an error that I think is due to it trying to trigger while collection is still taking place. I may very well be wrong in this, though. It comes out of the niScope MultiRead block, and says
niScope Multi Read WDT.vi:1<ERR>A previous acquisition is still in progress. If you are attempting to change an attribute, note you can only change fetch attributes while an acquisition is still in progress.
Status Code: -1074118647
Attached is the current state of the VI. I don't think the minor changes I've added in should be causing the error.
Thanks,
Wolley
Attachments:
Test2.vi ‏73 KB

What it the valid trigger delay value for "niScope Configure Trigger Digital.vi" ?

Hello:
I am using "niScope Configure Trigger Digital.vi" in LabView 5.1.1 for NI5911 scope card.
The trigger source is RFI1.
I am trying to specify the trigger delay, but it looks like the only accpted value is 0.0s.
For example: setting delay time to 1ms (1.0m) results in the error message stating that invalid value had been passed for trigger delay.
Thank you.
--daevper

The NI 5911 high speed digitizer does not support trigger delay; therefore its only valid input parameter for trigger delay is zero. The two high speed digitizers which do support trigger delay are the NI 5112 and the NI 5122.
There is a helpful listing in the NI High-Speed Digitizers Help which displays the features supported by each device (Start >> All Programs >> National Instruments >> NI-Scope >> Documentation >> NI High-Speed Digitizers Help >> Content tab >> Devices >> Features Supported by Device). If you did not install the documentation along with the driver, you can also download this support file here.
I hop
e this helps!
Regards,
Sonya Wornson
Applications Engineer
National Instruments

Error reading configuration file

I've setup the Adobe Access 4.0 trial license server and when I run the Validator.bat with -g -r on the Tomcat install dir \licenseserver I get an 'Error reading configuration file' message. Here is the log dump:
[] 2012-12-20 22:46:32,176 INFO [[Partition(flashaccessserver)].com.adobe.flashaccess.server.license.context.SimpleContex tFactory] Creating class loader for partition 'flashaccessserver' with libraries '[file:/c:/Tomcat6/licenseserver/flashaccessserver/libs/, file:/c:/Tomcat6/licenseserver/flashaccessserver/libs/flashaccess-license-server-ext-samp le.jar]'
[] 2012-12-20 22:46:32,582 ERROR [[Partition(flashaccessserver)].com.adobe.flashaccess.server.license.tools.Validator] Failed to validate tenant deployment 'flashaccessserver/sampletenant'
com.adobe.flashaccess.server.common.configuration.ConfigurationException: Error reading configuration file
          at com.adobe.flashaccess.server.license.configuration.commonsadapter.Constants.parseTenantCo nfigurationStream(Constants.java:139)
          at com.adobe.flashaccess.server.license.configuration.commonsadapter.TenantConfigurationImpl .<init>(TenantConfigurationImpl.java:110)
          at com.adobe.flashaccess.server.license.configuration.commonsadapter.CommonsConfigurationBas edFactory.getTenantConfiguration(CommonsConfigurationBasedFactory.java:90)
          at com.adobe.flashaccess.server.license.tools.Validator.validateTenantDeployment(Validator.j ava:255)
          at com.adobe.flashaccess.server.license.tools.Validator.validatePartitionDeployment(Validato r.java:283)
          at com.adobe.flashaccess.server.license.tools.Validator.validateGlobalDeployment(Validator.j ava:301)
          at com.adobe.flashaccess.server.license.tools.Validator.process(Validator.java:173)
          at com.adobe.flashaccess.server.license.tools.Validator.main(Validator.java:117)
Caused by: org.apache.commons.configuration.ConfigurationException: Unable to load the configuration
          at org.apache.commons.configuration.XMLConfiguration.load(XMLConfiguration.java:863)
          at org.apache.commons.configuration.XMLConfiguration.load(XMLConfiguration.java:821)
          at com.adobe.flashaccess.server.license.configuration.commonsadapter.Constants.parseTenantCo nfigurationStream(Constants.java:134)
          ... 7 more
Caused by: org.xml.sax.SAXParseException; lineNumber: 121; columnNumber: 16; cvc-complex-type.2.4.b: The content of element 'KeyServer' is not complete. One of '{"http://licenseserver.flashaccess.adobe.com/tenant":File}' is expected.
          at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.createSAXParseException(Unkno wn Source)
          at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.error(Unknown Source)
          at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(Unknown Source)
          at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(Unknown Source)
          at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(Unknown Source)
          at com.sun.org.apache.xerces.internal.impl.xs.XMLSchemaValidator$XSIErrorReporter.reportErro r(Unknown Source)
          at com.sun.org.apache.xerces.internal.impl.xs.XMLSchemaValidator.reportSchemaError(Unknown Source)
          at com.sun.org.apache.xerces.internal.impl.xs.XMLSchemaValidator.elementLocallyValidComplexT ype(Unknown Source)
          at com.sun.org.apache.xerces.internal.impl.xs.XMLSchemaValidator.elementLocallyValidType(Unk nown Source)
          at com.sun.org.apache.xerces.internal.impl.xs.XMLSchemaValidator.processElementContent(Unkno wn Source)
          at com.sun.org.apache.xerces.internal.impl.xs.XMLSchemaValidator.handleEndElement(Unknown Source)
          at com.sun.org.apache.xerces.internal.impl.xs.XMLSchemaValidator.endElement(Unknown Source)
          at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanEndElement(Unk nown Source)
          at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl$FragmentContentDri ver.next(Unknown Source)
          at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl.next(Unknown Source)
          at com.sun.org.apache.xerces.internal.impl.XMLNSDocumentScannerImpl.next(Unknown Source)
          at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanDocument(Unkno wn Source)
          at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(Unknown Source)
          at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(Unknown Source)
          at com.sun.org.apache.xerces.internal.parsers.XMLParser.parse(Unknown Source)
          at com.sun.org.apache.xerces.internal.parsers.DOMParser.parse(Unknown Source)
          at com.sun.org.apache.xerces.internal.jaxp.DocumentBuilderImpl.parse(Unknown Source)
          at org.apache.commons.configuration.XMLConfiguration.load(XMLConfiguration.java:855)
          ... 9 more
I'm using a relative path to my .pfx file for both the transportServerCredential and licenseServerCredential in the flashaccess-tenant.xml and my password has been scrambled using the Scrambler.bat.
Also, when I verify setup using http://<LicenseServer>:8080/flashaccessserver/flashaccess/license/v2 I get the message 'License server is setup correctly.'
Any ideas of why the Validator.bat can't read the configuration file?

I agree with you that if I can successfully playback content the license serve is setup successfully. Here is what I've tried and how I've set things up:
I have my license server setup (its the Protected Streaming version).
I'm using Adobe Media Server as my content/packaging server. I successfully served Vanilla PHLS sample streams to the sample Adobe Access player on iOS devices.
I have configured the Adobe Media Server to point to the license server and certificates as per the documenation and this Adobe Dev article (http://www.adobe.com/devnet/adobe-media-server/articles/content-protection-using-phds-phls .html). Since I am using a trial version of Adobe Access my .der files are the same for transport and packaging.
I am using the local key mode to remove one more variable (I have setup a remote key server as well).
I have placed a copy of the 'vod-policy.pol' policy file from the reference license server resources directory in my Adobe Media Server 'creds' directory and used the relative path '..creds/vod-policy.pol' in the httpd.conf file.
When I attempt to load the sample stream http://<mymediaserver>/hls-vod/sample2_1000kbps.f4v.m3u8 using the Adobe Access sample player on my iOS device I receive the following errors in the player:
DRM error Major[3363] minor:[0] NSError:(null)]
From my knowledge of working with the Adobe Access Objective C library to create a PhoneGap plugin it appears that a decrypted playlist is not being returned by the Adobe Media Server. Additionally, I can find no information in the Adobe Media Server or Adobe Access logs that pertain to my setup.
I would love to have someone from Adobe speak to the problems I am having. I find the documentation to be hit and miss and most of my successful results during this proofing process have been from piecing together disparate pieces of information and trial and error. Information on using the Adobe Media Server with Adobe Access is limited to one Devnet article (above) and the help in Adobe Media Server that doesn't explain pathing to the license server or Java policy files in any detail.
Colour me frustrated

I just installed LV2011 and one dll from my vi won't load with the error "application configuration is incorrect"

I just installed LV2011 and one dll from my vi won't load with the error "application configuration is incorrect", which is Windows lingo for "missing package dependencies". All the computers at my company with 2010 loaded seem to do OK. When I do a Dependencies Walk I get missing Visual C debug dll's missing plus IEshims and wer which both have a whole tree of dependencies missing on my machine. The Windows install is the same "Windows XP version 2002 Service Pack 3" on my PC and the working PC's. So I'm thinking I have to uninstall 2011 and go back to 2010. Is this correct? Those VC debug dll's were installed on the machines with 2010 in them but were not installed in mine.
I've heard the advice to recompile the dll with debug turned off but I don't have access to the source code.
Thanks in advance.

u87 wrote:
Thanks for the reply. This at least tells me that going back to LV2010 is not likely to solve the problem. The missing dll's are:
MFC90D.dll
MSVCR90D.dll
IESHMS.dll
WER.dll
And, once again, IESHMS and WER have other dependencies. So perhaps i need to install the Visual C++ development environment.
IESHIMS.dll is an Internet Explorer DLL that gets usually delay loaded by shdocvw.dll. As delay load it can not cause DLL load errors but only runtime errors. Maybe your DLL has it as direct dependency but that is unlikely since it does not have a documented interface.
WER.dll is Windows error reporting for Vista/Win7.
MFC90D.dll is the Microsoft Foundation classes and MSVCR90D.dll is the MS C runtime library, both as debug variant.
So all the DLLs you mention are actually MS DLLs! You haven't identified the DLL that you try to access in LabVIEW that causes these error messages. IESHIMS and WER are usually delay loaded by any component that needs it and should not likely be used by non MS code.
What is the DLL you try to load into LabVIEW and by whom? Get the provider of that DLL to provide you a non Debug build of the DLL. Installing Visual C on all the machines just to make the DLL load is not a solution, besides that it is likely not legal since I doubt you have that many licenses.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

One of my dll's in my vi doesn't run with the error "application configuration is incorrect"

I just installed LV2011 and one dll from my vi won't load with the error "application configuration is incorrect", which is Windows lingo for "missing package dependencies". All the computers at my company with 2010 loaded seem to do OK. When I do a Dependencies Walk I get missing Visual C debug dll's missing plus IEshims and wer which both have a whole tree of dependencies missing on my machine. The Windows install is the same "Windows XP version 2002 Service Pack 3" So I'm thinking I have to uninstall 2011 and go back to 2010. Is this correct? Those VC debug dll's were installed on the machines with 2010 in them but were not installed in mine.
Thanks in advance.

Hm,
it seems that you might have more success in the LabVIEW forum here; this one is for LabWindows/CVI...

Error -- No Such Trigger('when-button-pressed')

Hi,
I am getting the error ""No Such Trigger('when-button-pressed')"",
when I am executing the code EXECUTE_TRIGGER( 'WHEN-BUTTON-PRESSED' );
on some item(Key-Next-Item), although WHEN-BUTTON-PRESSED trigger exists.
What could be the problem ?. It worked till yesterday, giving error from today, I havent
changed any thing.
Thanks in Advance
Devender

Steve's tip is the only good solution for this case.
The problem in your case for example is:
Let's say you have a block-trigger, which fires after your execute-trigger.
Now a colleague of you, which don't know your code, create a WHEN-BUTTON-PRESSED on an item, then the new code is started and not the block-trigger-code.
So, don't ever do this. Write your code in a package-function or -procedure and call it from the trigger. So you can re-user the functionality
Gerd

Error 1070023 Configured Disk volume does not exist.

Hi
I installed Essbase 11.1.1.2 in stand alone mode. When I am trying to start Sample.Basic, I am getting the below error
Error 1002097 Unable to load database Basic.
The App log showed the following error
Error 1070023 Configured Disk volume does not exist.
Please help..

So everything works when the volume is set to E?
If so, you might be able to use DISKVOLUMES E in the essbase.cfg file which sets a default (for BSO cubes, at least), but you shouldn't have to do that.
The DISKVOLUMES documentation says that the volume that contains your ARBORPATH is the one used by default. Not completely sure I trust that it's up to date, and isn't now ESSBASEPATH or something else, but regardless, do those variable all look to be set correctly? To be honest, that's a longshot, as I'd be surprised if a missing / incorrect value there wouldn't cause bigger problems...

Good afternoon.I have a computer with W Vista 8, Windows office home and business 2013. I recently tried to install Photoshop Elements by CD with serial number but on the desktop appears the following message: error 1 (configuration problem) try to uninst

What's error 1 in adobe photoshop elements configuration? I have a computer with W Vista 8, Windows office home and business 2013. I recently tried to install Photoshop Elements by CD with serial number but on the desktop appears the following message: error 1 (configuration problem) try to uninstall and reinstall. I have done this but the message continues to appear

You haven't mentioned which version of PSE. If it is PSE 13, that requires a minimum of windows 7.

Getting error while creating trigger!!

Hi Guys,
I am getting the following error while creating trigger in Oracle10g Database in TOAD environment.
Error: PLS-00306: wrong number or types of arguments in call to '='
Table details:
One of the column having BLOB Data type in the table.
In the trigger, I have compared :old and :new values.
CREATE OR REPLACE TRIGGER INPL.trigger_new
AFTER INSERT OR UPDATE OR DELETE
ON TABLE_NEW REFERENCING NEW AS NEW OLD AS OLD
FOR EACH ROW
DECLARE
action_flag VARCHAR2(1);
new_image BLOB;
BEGIN
IF UPDATING
THEN
action_flag := 'U';
ELSIF DELETING
THEN
action_flag := 'D';
ELSIF INSERTING
THEN
action_flag := 'I';
END IF;
IF (:NEW.image = :OLD.image)
THEN
new_image := '';
ELSE
new_image := :NEW.image;
END IF;
INSERT INTO TABLE_NEW(action_flag, date_changed,nimage,oimage) values(new_image,:old.image);
end;
Any one knows about this issue, please let me know with the proper solution.
Thanks for your immediate response!
Regards,
Lakshman

CREATE OR REPLACE TRIGGER INPL.trigger_new
AFTER INSERT OR UPDATE OR DELETE
ON TABLE_NEW REFERENCING NEW AS NEW OLD AS OLD
FOR EACH ROW
DECLARE
action_flag VARCHAR2(1);
new_image BLOB;
BEGIN
IF UPDATING
THEN
action_flag := 'U';
ELSIF DELETING
THEN
action_flag := 'D';
ELSIF INSERTING
THEN
action_flag := 'I';
END IF;
IF (:NEW.image = :OLD.image)
THEN
new_image := '';
ELSE
new_image := :NEW.image;
END IF;
INSERT INTO TABLE_AUD(action_flag, date_changed,nimage,oimage) values(new_image,:old.image);
end;
I am getting the error in line at If condition
Error: PLS-00306: Wrong number or tpyes of arguments in call '='
Please let me know if any one knows exact solution!
Thanks in advance!
Regards,
Lakshman

Getting an error while configuring VMM for System Center 2012. error - An internal error has occurred trying to contact an agent on the WIN-NTJU8CNU server: : . Ensure the agent is installed and running.

Hi,
I am trying to install "System Center 2012 - Virtual Machine Manager by Using a Pre-Configured VHD".
I downloaded install guide & the binaries from http://www.microsoft.com/en-us/download/details.aspx?displaylang=en&id=10712
I have followed the installation document & getting an error while configuring VMM for System Center 2012.
error details from log file given below:
01:12:24:VMMPostinstallProcessor threw an exception: Threw Exception.Type: Microsoft.Carmine.WSManWrappers.WSManProviderException, Exception.Message: An internal error has occurred trying to contact an agent on the WIN-NTJTNEJ1UCN.mydomain.com server: : .
Ensure the agent is installed and running. Ensure the WS-Management service is installed and running, then restart the agent.
01:12:24:StackTrace:   at Microsoft.Carmine.WSManWrappers.ErrorContextParameterHelper.ThrowTranslatedCarmineException(WsmanSoapFault fault, COMException ce)
   at Microsoft.Carmine.WSManWrappers.WsmanAPIWrapper.RetrieveUnderlyingWMIErrorAndThrow(SessionCacheElement sessionElement, COMException ce)
   at Microsoft.Carmine.WSManWrappers.WsmanAPIWrapper.Invoke(String actionUri, WSManUri targetUri, Hashtable parameters, Type returnType, Boolean isCarmineMethod, Boolean forceResponseCast)
   at Microsoft.Carmine.WSManWrappers.AgentManagement.AssociateLibrary(WsmanAPIWrapper wsmanObject, String CertificateSubjectName, String& ExportedCertificate, ErrorInfo& ErrorInfo)
   at Microsoft.VirtualManager.Setup.VirtualMachineManagerHelpers.AssociateAgentServer(String fullyQualifiedServerName)
   at Microsoft.VirtualManager.Setup.VirtualMachineManagerHelpers.AssociateDefaultLibraryServer()
   at Microsoft.VirtualManager.Setup.VirtualMachineManagerHelpers.SetupLibraryShare()
   at Microsoft.VirtualManager.Setup.InstallItemCustomDelegates.PangaeaServerPostinstallProcessor()
01:12:24:InnerException.Type: System.Runtime.InteropServices.COMException, InnerException.Message: There is a time and/or date difference between the client and server.
01:12:24:InnerException.StackTrace:   at WSManAutomation.IWSManSession.Invoke(String actionUri, Object resourceUri, String parameters, Int32 flags)
   at Microsoft.Carmine.WSManWrappers.MyIWSManSession.Invoke(String actionUri, Object resourceUri, String parameters, Int32 flags)
   at Microsoft.Carmine.WSManWrappers.WsmanAPIWrapper.Invoke(String actionUri, WSManUri targetUri, Hashtable parameters, Type returnType, Boolean isCarmineMethod, Boolean forceResponseCast)
01:12:24:ProcessInstalls: Running the PostProcessDelegate returned false.
01:12:24:ProcessInstalls: Running the PostProcessDelegate for PangaeaServer failed.... This is a fatal item. Setting rollback.
01:12:24:SetProgressScreen: FinishMinorStep.
01:12:24:ProcessInstalls: Rollback is set and we are not doing an uninstall so we will stop processing installs
I have completed MSSQL server configuration and while configuring VMM the below error displayed in the wizard:
An internal error has occurred trying to contact an agent on the WIN-NTJTNEJ1UCN.mydomain.com server: : .
Ensure the agent is installed and running. Ensure the WS-Management service is installed and running, then restart the agent.
I have checked that the following services are running:
1) Verified WS-Management srvice 2) MSSQL server + MSSQL (agent) 3)SC VM Manager Agent 4) Windows management instrumentation .
I have joined the VM (on which installing SC VMM) in a domain(as per install guide) and installing VMM using domain account & it is in local Administrators group.
Also I would like know if there is any stand alone SC VMM installer. If yes then please let me know the installer location & install guide.
thanks.
====

Have you installed AppController on the same machine with VMM?

Error at configuring LDAP Synch by using post installation steps of OIM

Hi All ,
I am getting error while configuring LDAP synch.......
i am doing LDAP synch by using following link http://docs.oracle.com/cd/E27559_01/integration.1112/e27123/oid_oim.htm#IDMIG4357
While Running patch_weblogic.sh script i am getting following error
Error:
patch:
explode-archived-apps-was:
seed-ootb-jobs:
seed-ootb-jobs:
[echo] ----> SEEDING OUT OF THE BOX SCHEDULE JOBS AND TRIGGERS
[java] Exception in thread "main" java.lang.ClassNotFoundException: oracle.jdbc.xa.client.OracleXADataSource
BUILD FAILED
/apps/Oracle/Middleware/Oracle_IDM1/server/setup/deploy-files/setup.xml:21: The following error occurred while executing this line:
/apps/Oracle/Middleware/Oracle_IDM1/server/setup/deploy-files/setup.xml:84: The following error occurred while executing this line:
/apps/Oracle/Middleware/Oracle_IDM1/server/seed_data/seed-rcu-data.xml:37: Java returned: 1
Total time: 26 seconds
*********I can't trouble shoot this error.....because i am not able to find out oracle.iam.scheduler.seed.SeedSchedulerData class is in which jar.
Please help me to solve this problem
Regards,
idmr2

Open weblogic.profile and change the value for property operationsDB.driver to oracle.jdbc.OracleDriver and retest the issue.

Error while configuring work repository details in topology Manager

Hi,
Could anyone pls advice, is it possible creating more than one Master repository connection for the same instance.
When i try to do so, am getting the below error while configuring the work repository details in topology manager.
“A work repository already exists for this connection.
Enter the repository password to declare it in your Master Repository”
I tried with both the new master and work repository password. But no luck.
Previous Master & work details:
Master: PCS_MASTER
Work:PCS_WORKREP
New Details
Master: PCS_MASTER_INT
Work:PCS_WORKREP_INT
Instance: PCBID
Am trying to create new master repository for PCS_MASTER_INT.

In the same oracle schema you can have only 1 master and 1 work repository. Usually they take 2 schema (1 for each).
If you need 2 master repository you have to use 2 different jdbc path. I'm using a db with several master / work, each repo has got its schema..

Error while configuring Vintella SSO

Hi,
I'm trying to implement SSO with Vintela in BO XI3.1 SP3
AD Authentication is working corectly.
I'm getting the following error after configuring Vintela, the error shows when trying to login:
"HTTP Status 500 - com.wedgetail.idm.sso.ProtocolException: com.wedgetail.idm.spnego.server.SpnegoException: GSSException: Failure unspecified at GSS-API level (Mechanism level: com.dstc.security.kerberos.KerberosException: Successfully matched service principal "HTTP/SERVER" but not key type (23) + KVNO (143) in this entry: Principal: HTTP/SERVER Type: 1 TimeStamp: Wed Dec 31 18:00:00 CST 1969 KVNO: -1 Key: 3, ad c1 7f df e3 61 9e 9e )"
I have also tried to use :
-Dcom.wedgetail.idm.sso.password=Password in the Java configuration, (commenting the keytab entry on Web.xml) but when I comment the idm.keytab in the web.xml, I can't even reach the Infoview login page, It shows a 404 error
Any help will be appreciated
Thanks,
Akhil

Hi Michelle
I have changed the Client in Java from 000 to 001. I have added the certificate to ACL in 001 in my ABAP system. After doing that, I am getting the following error message.
N Comparing certificates ...N *** ERROR => ASN.1 blob lengths are not identical. 575 769. [ssoxxkrn.c   2074]
Leaving VerifyOwnSystemInfo...
N HMskiVerifyOwnSystemInfo failed with rc=19.
N *** ERROR => Neither was ticket issued by myself nor can I find issuer in TWPSSO2ACL (see note 1055856). [ssoxxkrn.c   1067]
N dy_signi_ext: issuer not trusted
M *** ERROR => SosIAnchorArrayCreatable: T42/M0 in state cancel [thxxtool2.c 947]
My TWPSSO2ACL Entries Client 001.
============================
MANDT WPS_SYSID WPS_MANDT
001                 BWD       001
The Production client in ABAP is 100 and not 001. when I have changed the Clinet 100 in Java, then also I am getting the error message mentioned in my main question.
So I am confused as to where I can make the changes in the system. Please advise!!!!!!!!!!

Error while configuring Enterprise manager

Hello,
I want to configure enterprise manager, while creating a new database using database configuration assistant in oracle 11g i am getting following error message
*"Configuring database with database control requires a listener to be configured in the current oracle home.
You need to run Netca to configure a listener before you can procede. Otherwise you may choose o continue with out Database control configuration"*
My OS is Windows 7
is there any other way to configure Enterprise manager OR do i need to install any specific package
Thank you friends.

Hi, Finally i created a listener "KUMAR"
*Microsoft Windows [Version 6.1.7600]*
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Users\praveen kumar gogula>lsnrctl status
LSNRCTL for 64-bit Windows: Version 11.2.0.1.0 - Production on 22-SEP-2011 17:50
*:44*
Copyright (c) 1991, 2010, Oracle. All rights reserved.
Connecting to (ADDRESS=(PROTOCOL=tcp)(HOST=)(PORT=1521))
STATUS of the LISTENER
Alias                     KUMAR
Version                   TNSLSNR for 64-bit Windows: Version 11.2.0.1.0 - Produ
ction
Start Date                22-SEP-2011 17:44:58
Uptime                    0 days 0 hr. 5 min. 48 sec
Trace Level               off
Security                  ON: Local OS Authentication
SNMP                      OFF
Listener Parameter File   C:\oracle\product\11.2.0\dbhome_1\network\admin\listen
er.ora
Listener Log File         c:\oracle\diag\tnslsnr\praveenkumarg\kumar\alert\log.x
ml
Listening Endpoints Summary...
*(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=praveenkumarg)(PORT=1521)))*
*(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1521ipc)))*
Services Summary...
Service "CLRExtProc" has 1 instance(s).
Instance "CLRExtProc", status UNKNOWN, has 1 handler(s) for this service...
Service "praveen" has 1 instance(s).
Instance "praveen", status READY, has 1 handler(s) for this service...
Service "praveenXDB" has 1 instance(s).
Instance "praveen", status READY, has 1 handler(s) for this service...
The command completed successfully
C:\Users\praveen kumar gogula>
What to do next?

Error iviscope configure trigger

Similar Messages

Maybe you are looking for