Error Message linked to satellite ISP?

Hi,
So glad to have found this forum, as I am very frustrated.
I live in a rural area, and recently went into contract with a satellite ISP. It's hughes net, actually, and since having done so, I'm having trouble with uploading my sites to .mac.
When I click "publish", it begins to log in to my mac account, then it uploads the start page of my first site (I have two) and then, I get this message: "Error - shapeimage_2.png" and it doesn't finish uploading.
I have tried to take all the photos off my site, I have tried deleting all the new info since my last good upload - I have done almost everything I can think of. My iweb has gone from publishing without issue when I first started using it last fall, to publishing only if there are no other programs open, and I'm not even breathing close to it. So tempermental lately! And now, with this new satellite, (which is a hundred times faster than the dial-up we were using) it won't finish publishing.
I did notice that, somehow, the start page on my first site, online, was update with my changes. But nothing else. The blog which I updated at the same time, was not uploaded, so it seems that it did put the start page up, but didn't update the rest of the site, once it gave me the error message. It does not update the start page of my second site, at all.
Can anyone help? I'm really in a pinch, as I need to update my sites and get them current. If it's connected to the satellite internet, how do I get around it, so I can continue my sites?
Thanks!
G4 iBook Mac OS X (10.4) Running Tiger

Thanks for your input, QTK, but yeah, this is a totally unacceptable option for me. I don't have any other place to upload this website - I work from home, don't even know of any public place (nor friend/relative/neighbor) using macs in my area, except for some schools and they aren't using iWeb, according to my IT guy. I have a hard time believing apple is so far behind the times, they can't figure out something to bridge the gap...especially since broadband satellite isn't a brand-spanking new idea. It would have been nice to have been able to read a warning or something, before I paid for the yearly subscription to .mac.
I've narrowed it down to a "network" problem, after consulting the apple help people. Network = Broadband satellite connection, I'm assuming. It would be helpful to know what "shapeimage_2" is on my site, but I haven't seen anything to lead me to believe that I can get that information. I guess it doesn't matter, since it's all going back to the connection.
I am really ****** about this. I had no reason to think that of all my connections in my house and what not, this one dinky website program would be the thing that wouldn't mesh with my apparently alien satellite ISP. If I'm able to figure anything out about this - which I'm not expecting to, because it seems I've tapped all the apple resources on this gig - I'll come back and post the solution.
g4 Mac OS X (10.4)

Similar Messages

Error message starting up Satellite L730

Hey guys, I've encountered a problem with my satelitte L730.
Whenever it turn the laptop on, an error message comes up
Saying:
For Atheros PCIE Ethernet controller V2.0.2.3
Check Cable connection
PXE-MOF: exiting intel PXE ROM.
No bootable device -- insert boot disk and press any key.
Intel undi, PXE-2.0.
Could not link picture but this happens everytime I start the laptop.
Any advice/ recommendations that anyone could offer would be great.
Thanks.
Message was edited by: Meemu

Now whenever I turn the Laptop on, that screen does not pop up, just gets stuck on the toshiba boot up screen and the whirring noises inside the Laptop are getting louder and louder, close to a grinding sound.
Any information on this would be a real help, thanks

Error message linking to field

Hi guys,
I'm trying to generate an error message that links to the field when clicked on.
My problem is this. This error message is for a dropdown list. When user choose a blank selection, it will generate the error message to "fill in the mandatory field", with the link to the dropdown box.
I tried lo_message_manager->report_attribute_error_message but it gives an error dump for null values (due to blank selection).
I have also tried cl_wd_dynamic_tool=>check_mandatory_attr_on_view. This works fine for the other inputfields, but it doesn't work for the dropdown list.
Please advise. Thank you very much.

Hi,
how is your dropdown done? by key/index?
because with an indexed one, none is selected, thus returning a dump when you try to have
an attribute error message (initial selected element).
Greetz,
Koen

Strange error message - linked lists (again)

I have to keep at this linked list thing if I'm ever going to really understand it!!
I have created a method to create a linked list via user input. I'm receiving only one strange ERROR, which states:
"This method must return a result of of type ListADT.Node."
And I have just started building my class ListADT...
class ListADT{
public Node createList(int aNumber){     // THIS IS WHERE THE ERROR POINTS
      * integer variable aNumber is the length of the list user wishes to create.
     Scanner console = new Scanner(System.in);
     int number;                    // declare variable number as an integer.
     Node newNode = new Node();          // declare and initialize newNode.
     Node first = new Node();          // declare and initialize first.
     Node last = new Node();               // delcare and initizlize last.
     try
          for(int i = 0; i <= aNumber; i++){               // for loop to enter numbers to build list.
          System.out.println("Please enter an integer: ");     // prompt user.
          number = console.nextInt();                    // assign user input to variable number.
          newNode.info = number;          // assign number to newNode;
          if(first == null){               // checks to see if Node first is a null value.
               first = newNode;          // if true, then this node is the first and last node in the list.
               last = newNode;
          else{                              // if first is not null, then newNode is placed at the end of the list.
               last.link = newNode;
               last = newNode;
          return first;
     catch (InputMismatchException imeRef)     //Catches non-integer values
          System.out.println("You entered a non-Integer! " + imeRef.toString());     //Prints error message

Now why can't the error messages help
out a little more? I would have never guessed that
there was a problem with the catch block not
returning anything!!The message was pretty informative -- it told you what was wrong. If the compiler could be so smart as to be able to tell you exactly what to fix, then the compiler would be able to write code all by itself -- and then you'd be out of a job.

32bit Windows 7 and error message shown on Satellite T series

Help needed for this computer dummy.
I started to install 64 bit windows 7 then clicked cancel midway through, after I realised that perhaps this might require too much RAM.
Now getting persistent error message (F3- F200-0002). What should I do? (need explicit instructions as relatively inept)

It is really stupid situation now.
As far as I know this notebook has no optical disc drive so for OS installation you must try to use HDD image.
Try again to install it using F8 at start-up.
If this will not work I am afraid you have destroyed recovery image and only solution for you is to order new one under https://backupmedia.toshiba.eu/landing.aspx
You can install it if you connect external USB optical disc drive.

Idoc Import phrase - error message link to language

Hi all,
I configured an ALE betwenn 2 SAP systems.
I received some idocs in oder to import phrase in the target system.
When I proccess the idoc i have the following error message: "Cannot create phrase text in source language" and the second one is "Phrase language 5 does not exist in Customizing".
Anybody can help me please?
Thanks
/Ludo

yes, some languages are not present in the target system regarging source target.
The problem is that the source system is unicode and the target is no unicode system and i am not able to add language in the target system.
I will try to apply filter in the source system.
Thanks for your reply!
/Ludo

Error message on startup Satellite C655-S5068

Error C++runtime library C:\windows\system32 spoolsv.exe. also an error stating that NET. Framework 2.0 is missing but when you download it from microsoft it says that its already installed . Tried downloading Net. 4 to no avail. Have also reloaded Lexmark printer driver(disc and over the internet (Lexmark site) more than once to no avail(Lexmark 5600-6600 series) Help

Satellite C655-S5068
Error C++runtime library C:\windows\system32 spoolsv.exe.
also an error stating that NET. Framework 2.0 is missing
It does look like that spoolsv.exe file is corrupt.
I would first try a System Restore to before the problems occurred.
   What is System Restore?
Whether or not that fixes things, you should burn a repair disc if you haven't yet.
   Create a system repair disc
If necessary, use it to boot to the Windows Recovery Environment and run Startup Repair.
   How to Use a System Repair Disc to Restore Windows 7
Let us know how it goes.
-Jerry

Error message when booting Satellite P series - "Exiting PXE-ROM"

A while ago, I accidentally deleted the active partition to my hard drive. OOps. That is not very nice, because even though I wanted to clean out the drive and start fresh, the laptop would not recognize a hard drive any more. I live in the british virgin islands where we've got lots of rum and sand but no computer parts! So I bought a new hard drive, and it did not solve the problem. Turns out that drive was no good. Bummer. I was recently in California (lots of computer parts there) and had some tech people confirmed the drive was bad and yet another drive was put in. Unfortunately the people there did not have time to fix the laptop before I left. Now I'm pretty certain that the Hard drive is good.
So now I have a good drive, but whenever I try to boot, I get stuck at the following message:
Intel UNDI, PXE-2.0 (build 082)
Copyright (C) 1997-2000 Intel Corporation
For Realtek RTL8139(X)/8130/810 PCI fast ethernet controller v2.13 (020326)
PXE-E61: Media test failure, check cable
PXE-MOF: Exiting PXE ROM.
NO matter what boot sequence I use (I can get to the setup), I can't get the computer to boot to any CD. I even tried to put a version of Ubuntu on a pen drive to try and boot to that. Nothing Every time I get the same message.
If I remove the hard drive, I get the same message, except it repeats itself every few seconds. With the HD in it only does it once.
What should I do now?

The PXE-ROM message appears because the notebook tries to boot from the LAN.
We can speculate why the notebook want to boot from the LAN.
Either the other devices like HDD and CD/DVD drive dont function correctly, controllers are not recognized by BIOS or there is a simply wrong booting order.
If you want to boot from the HDD or ODD you can press the F12 immediately after notebook starting and the boot menu should appears. Then you could choose the right boot device.
Anyway, if its not able to choose such device you should access the BIOS and should set the BIOS to the default settings and save these settings!
Good luck

Where or How to configure the error message linked to Browser compatibility

Hello,
I am looking for the way of changing this text :
" Could not open iView. The iView is not compatible with your browser, operating system, or device. Contact your system administrator for more information"
that appears when we try to open the portal with Opera browser.
Does anyone has an idea ?
I have looked into the UmLogonPage.jsp on the logon screen, but it seems to be checked before.
Thanks a lot.
Fabien.

Seems like we can't
Fabien.

Error while linking DMS document in cProject

Hi,
When I link the document of DMS in cProject an error message
`` Link Not Possible: The SAP R/3 DMS document info record contains orig( Message number 26 000)``
is appearing. I could search the list of documents . I am facing this issue only selecting and clicking the continue button under SAP DMS tab in cProject. RFC is doing well. Pls help me to solve the issue.
Regards,
Ramesh

Hi,
Please check after using following steps.
Goto - SPRO -
> Collaboration Projects---->Structure---> Define Project Type
Please select the your project type and check SAP DMS is selected under tab Active Function.
Regards

Handling Error Messages in Process Chain

Hi Gurus,
I am developing a process chain which contains more than 40 Master Data Objects. Those are connected serially with "always" link.
Start -> Load Data -> DTP -> Load Data -> DTP -
EX-OR (connected to all Processes for error message)
Here the EX-OR Process is not allowing me to connect with "Error" link to all processes (by default it is giving "Always" link). i.e i want to get the error message from EX-OR process only in the case of failure not always.
Can any one help me out.
Thanks in advance,
Chenna.

Greetings Chenna,
First we need to check why the "always" link is used to connect the process chain steps?
If you take such "always" link to connect the steps, we cannot raise an error message link to EXOR( by default it will also take "always" link)
Here we can explore an error message thru EXOR step whenever a failure occurs in the process.
Things we need to do:
1. Steps in the process chain should be connected only on "successful" option selected.
2. We need to link the required steps to the EXOR step with "errors" selected on the pop up.
3. Need to link an Error message to EXOR step by selecting "Create message" on EXOR step.
Now if any failure occurs in the process the error message will be raised.
this helps...

Object variable or With block variable not set error message

When processing the Rate application I get a "Object variable or With block variable not set error message" What is causing this error and how do I fix it?

Hi Brian,
I'm afraid that in some ways this reply won't be very helpful though it may help you save some time.
The error message you describe is a very generic one thrown by Microsoft .NET (the programming platform that SAP is written with, see the link at the bottom of this message) and not being 'handled' by SAP.
This means from a SAP perspective that any one of many unrelated things may be causing the error and that it gives you virtually no help in tracking the problem down in SAP.
We've plagued by this message quite a bit, my advice is to look for clues at to what may be happening elsewhere, e.g. try:
1. The windows event viewer, if you are in a multi-server environment then check the event log on all machines.
2. The SQL Server event log (this can be found in Management Studio - Management - SQL Server Logs assuming you're using SQL Server 2005)
3. IIS logs, usually these are text files in the following location -
HTTP.SYS Error Log - %windir%\System32\LogFiles\HTTPERR
IIS Website Log - %windir%\System32\LogFiles\W3SVC#
It is dull work trawling through all these places looking for error events with a timestamp similar to the time your error was encountered, but by doing this we've been able to troubleshoot some issues that otherwise would have taken us ages to rectify via trial and error.
Sorry that there is no definitive answer, but if itu2019s of any help there's many more of us out there who this error message causes trouble for.
Regards,
Iain
Microsoft "Object variable or With block variable not set" error message link:
http://support.microsoft.com/kb/316478

Image Capture Error Message Pain in the B*** after installing 10.4.10

I installed the 10.4.10 upgrade, and ever since then when I switch on my Brother DCP 115 printer, I get an error message linked to Image Capture that the connection to the machine has failed, that I should check the cables, switch it off and on an try again.
But there is no connection failure, the machine works just fine. But I'm stuck with this error message that won't disappear unless I reboot the Mac.
I tried everything already. Resetting the printer system, setting up a new connection, shutting of Image Capture from accessing the scanner, reinstalling the drivers and software, repairing permissions, nothing works.
Strange phenomenon: after a reboot, everything works fine. After my Mac has been switched of for a couple of hours, the problem returns.
Mac support in Holland doesn't know of anything. They suggested to archive and repair, promised to mail me a how-to article, which never arrived, and I don't have a clue.
Any ideas, anyone???

I installed the 10.4.10 upgrade, and ever since then
when I switch on my Brother DCP 115 printer, I get a
message that the connection to the machine has
failed, that I should check the cables, switch it off
and on an try again. In the upper left corner is a
picture of a camera...
But there is no connection failure, the machine works
fine. But I'm stuck with this error message that
won't disappear unless I reboot the Mac.
I tried everything already. Setting up a new
connection, reinstalling the drivers and software,
repairing permissions, nothing works.
Strange phenomenon: after a reboot, everything works
fine. After my Mac has been switched of for a couple
of hours, the problem returns.
Mac support in Holland doesn't know of anything. They
suggested to archive and repair, promised to mail me
a how-to article, which never arrived, and I don't
have a clue.
Any ideas, anyone???
I have the identical problem except my printer is a Brother MFC440CN, so the problem is not printer model specific, perhaps not even unique to Brother.
The really annoying thing is that I cannot get rid of the message without using Restart or Shutdown. The OK button doesn't close it. The error message is [MTW005]
I think Apple needs to get on this and other issues associated with 10.4.10.
BNC

Forms Error Message Documentation

Dear Colleague,
Could someone please give me a link to documentation that contains the explanations of the Forms Error Messages, e.g. FRM-99999 etc.
I have not been able to find it in OTN.
Kind regards,
Randy

Yes, there are all available from the online help of the Forms builder.
click the Summary panel, then the reference -> All Forms error messages link
Francois

Muse 2014.3 Crash and error message - Image frame thinks it belongs to the page

I am trying to update an asset in my assets panel, but every time I try to update the asset, relink the asset, or delete the object containing the asset Muse crashes with the following error message:
"Link updated. Image frame thinks it belongs to the page. but the page disagrees."
I've sent this file to the Adobe email and linked the forum per requested for this same file, and I've never heard back from Adobe.

Please send your muse file at [email protected] along with this forum link in subject line. We will try to check the file and will update you over email.
Thanks,
Sanjit

Error Message linked to satellite ISP?

Similar Messages

Maybe you are looking for