Error message popping up over and over for no reason
I keep getting an error message that says my USB has been disabled because it was drawing too much power. This happened the first time when nothing was in the USB port and it happens over and over even when my computer is plugged in and not using and USB ports. Sometimes when I turn my computer on there are 3-4 messages all saying that same thing on the screen. I tried restarted and turning off for a while and turning back on but it's still doing it over a week later! Help!
Try Resetting the System Management Controller (SMC)
Follow the Steps here
http://support.apple.com/kb/HT3964
Similar Messages
-
Getting an Error Message: AA 698 ANLB and ANLC for asset not in Sync
Hi all Experts
I know there were previous thread on the similar issue. I read those and tried to follow the procedure mentioned but didn't work. First of all We are working on ECC 6.0 verion. We have couple of assets Which is giving a problem even when we display the asset. The error message AA 698 ANLB and ANLC for asset not in Sync.
We added a new depreciation area which was added to all the assets. the depreciation calculation for the new depreciation area is not updated in table ANLB. The asset were capitalized in 2009. I think the asset transfer was done using AS91. I initially thought it was fiscal year change problem but now as i open fiscal year 2009 and try to calculate the depreciation it keeps giving me the same error AA 698. There were various OSS notes mentioned which are all implementd in our system.
One more thing I see is that on the depreciation area which has issue which is not populated in ANLB table doesnot have ordinary depreciation start date. Which I tried to maintain using AS92 and reran the depreciation caluclation (AFAR) this also didn't work as its giving me the same error. Also this depreciation area doesn't have Operational rediness date, I think this date should populate from the value date of the asset.
Please let me know if you have suggestion
Thanks
RajanHi bernhard,
thanks for your reply. Below are my observation
1) Have ANLB-LGJAN and ANLC-GJAHR the same depreciaiton areas:
I had checked this earlier....ANLC doesnot have an entry for that specific deprectiation area. ANLB has an entry. This is where all the issue started.
2) Is the field T082AVIEWB-AUTHORITY on 2 (note 900767).
This note has been applied and the view is on 2
3)Are the following fields synchrone: ANLC-GJAHR = T093C-LGJAHR
These field are not synchrone: ANLC doesn't have an entry for depreciation area 82 other depreciation area are at 2009 in ANLC and in T093C-LGJAHR is in 2010. How can we sysnc these tables? Also how can I get depreciation area into ANLC table?
Thanks
RDK007 -
MG3250 Printer throws up error message - Scangear cannot communicate with scanner for these reasons
Hi
I have an MG 3250 printer running off an HP Pavilion Laptop using Windows 8.1. Every time I try to scan I get an error message that 'cannot communicate with scanner for these reasons...........etc'. The only way I can get the printer / scanner to work is by going through the Control Panel / Hardware & Printers route. This seems terribly slow and time consuming. What is wrong and what needs to be done to correct the problem?
ThanksI have the exact same problem as you with my new Canon LiDE 120. The errors I get are: 2, 156, 182, 55 and sometimes 77 when using it on my Windows 8.1 (64 Bit) desktop PC. I have tried installing and uninstalling the drivers multiple times, used different ports and still nothing. It does however work properly on a Windows 7 device.
My PC's specification is as follows:
Windows 8.1 (64 Bit) - With latest updates
Avast Premier
Malwarebytes
ASUS z87 Pro
Intel 4770k
ASUS GTX 670 (4GB)
8GB 1600MHz Kingston RAM
Things I have done
Tried different ports (USB 2.0 and 3.0)
Installed all software & driver from CD
Installed all software & driver from Canon Website
Installed only the latest driver from Canon Website (April 2015)
Tried to use Windows Fax & Scan, Scan, IJ Scan Utility, Scangear and Vuescan.
What happens
The physical buttons on the device are unresponsive
The computer says it is warming up, but nothing happens
It starts to scan for a few seconds and then comes to an abrupt end - this can happen at 10% of the scan or even at 91%.
Surely the problem cannot be with Windows 8.1 since the device was only released last year. What could be the issue? I called their support line and was advised to clear the drivers of previous scanners used by my system, I did this and there still is no change. Could somebody please help me! -
Error message pops up again after right correction of input
Dear experts:
I am doing a list using ALV control (OO), I put my validation logic in data changed handler. The validation is simple, to check whether a field is blank or not, if it is blank, pup up error messages and let the user to correct his/her input. But the strange thing is that after the error message firstly pops up, I close the error window,and input something in the field and press enter. No error message should be popped up. But the same error message pops up again. I debug the program found that after the first error, even I input something in the field, but the program does not get the value I input, so the same checking failed, and the error message pops up. And after the second popping up window has been closed, no further error message pops up when press Enter.
Does any1 have any idea?
Vincent
CODE:
METHOD HANDLE_DATA_CHANGED. "#EC NEEDED
DATA: LW_INS TYPE LVC_S_MOCE,
LV_FNAME TYPE LVC_FNAME,
LT_MOD TYPE LVC_T_MODI,
LW_MOD TYPE LVC_S_MODI,
LV_TEXT(10) TYPE C,
LV_MAX TYPE I,
LV_ROWID TYPE I,
LV_RES(12) TYPE C,
LW_LIST TYPE ZTSRE007.
LT_MOD] = ER_DATA_CHANGED->MT_MOD_CELLS[.
LOOP AT LT_MOD INTO LW_MOD.
IF LW_MOD-FIELDNAME = CNS_ZZTTSN.
LV_FNAME = CNS_ZZTTSN.
CALL METHOD ER_DATA_CHANGED->GET_CELL_VALUE
EXPORTING
I_ROW_ID = LW_MOD-ROW_ID
I_FIELDNAME = LV_FNAME
IMPORTING
E_VALUE = LV_RES
IF LV_RES IS INITIAL.
LV_ROWID = LW_MOD-ROW_ID.
CALL METHOD ER_DATA_CHANGED->ADD_PROTOCOL_ENTRY
EXPORTING
I_MSGID = CNS_MSGID
I_MSGTY = CNS_MSGTY
I_MSGNO = CNS_MSGNO
I_FIELDNAME = LV_FNAME
I_ROW_ID = LW_MOD-ROW_ID
ENDIF.
ENDIF.
CLEAR: LV_ROWID,
LV_FNAME.
ENDLOOP.
ENDMETHOD. "handle_data_changed
Moderator message - Cross post locked
Edited by: Rob Burbank on Sep 1, 2009 9:07 AMHi,
I am not sure how this is functioning but i am just trying to visualise your proble.
I feel that after you input the value after the first pop up of the error message; the PAI is not getting called and thats the reason why the new data is not transferred to the internal table.
What i suggest is after you input the data; press enter and check if the message is getting popped up again.
Also call the method CHECK_CHANGED_DATA in your PAI.
Just try with this. If not then probably there should be some thing else.
Can you share your code if possible??
Regards,
Ankur Parab -
I have a problem syncing iCal on my Macbook air (10.7.5) and my iPhone 4s (5.1.1) over iCloud. The following server error message comes up "The request (CalDAVAccountRefreshQueueableOperation) for account “iCloud” failed." Been to Apple Store - no luck instore, or with Super genius over the phone when with genius in store, taking data in real time via ethernet!
I had to do a full wipe of my system because of time machine back up issues 2 weeks ago, and the error has only occured at some point since then. I only did a drag and drop of my user account folders/files into an External HDD rather than a copy of my user account (advised by the staff in store at Apple to do this) and when reimported, the Mail folders are all present but each message is in a sub-sub-sub folder that is numerically named. I do not have a mirror image of the hard disk prior to the wipe, only a time machine back up from 2 weeks prior to it being done. I am uncertain if this reinstall has caused the issue.
I am not happy to upgrade the software in my iPhone until I have the calendars working. I have purchased Mountain Lion, but again am concerned about upgrading until the issues are sorted.
I have tried the other solutions on here with no luck. HELP please.
Many Thanks.Progress Update.
I made a back of what existing phtos and Videos I had on my Iplhone. I used Image capture to do this making an entire back up of photos and videoa that were still intact on the phone.
Image capture is god for this purpose, as it does exactly what you ask it to do without applying any rules or squishing the files back into iphote (which might also be corupted)
Image capture wil do the basic function of retriving the contents of the phone and save them as native files on your hard drive.
Once I did this I erased my iphone, and re intitialised it restoring an older back up from icloud.
As the retore was happneing - I did retreive the missing files that cuased the intial beviour as above, and I could play the videos that were missing in the above scenerio. The wierd ting was however that even though the source files were now back on the device, the thumbnail previews were missing. Where I ahd balck thumb nails for server portions of the resotred content.
I then went to bed as the restore is a long process. When I woke up the library had library had cleaned itself up. Mysteriously the prcess had deleted the files missing the their thumbnails.
This is very perculiar and bad behavior.
I am now repeating the process, and will attempt to download the missing content as it is restored and prior to the phone trying to fix itself.
Here are the lessons learned.
DO NOT rely on Photo Stream to keep back ups and synchornise videos from you IOS device. IT DOES NOT SUPPORT THIS CAPBILITY
DO NOT rely on iCloud Back Up alone - always fd an occassional iTunes back up or more reliably still always take a back up of photos and video files using Image Capture to be doubly sure that you a have backd up any content.
DO THIS NOW - dont wait to loose your phone ofr have your phone repaired by replacement at the apple Store. (I did both :-( -
After I installed firefox four a pop up dialog box started showing imediatley and clicking OK made it dissappear and return a split second later, over and over again. I typed in my eamil address to contact firefox about it in the dialog box for that but clicking the send button didn't send the message. The three posts about it where incomplete so I could not do those. 90 people have reported this problem. Please advise. Thanks.
http://support.mozilla.com/en-US/kb/Changing+the+e-mail+program+used+by+Firefox
-
Trouble Downloading Updater receive error message OVER and over again
Hello! I have that little folder picture on my ipod and when I went to the support site, it said that I needed to download the updater. I signed in and clicked download. The next thing that happens is that I get this message:
Our apologies but there was an error with your session (perhaps you were away from your computer for a while). Click here to return to the download page. It happens over and over again and won't let me download the updater. I have a Compaq Presario V2000 laptop with Windows Xp. Any suggestions would be greatly appreciated! I hope this is the right forum to ask this
PC Windows XPIs your iPod connected while you're trying to download this file? If so, I'd try a different approach. Turn off your computer to get rid of all temporary files. Then, when you reboot, download the updater file to your desktop. (When the file starts to download, tell it to Save to your Desktop--it shouldn't "Run"--it should "Save" and then you can click on the down arrow and choose desktop.) After the download completes, then hook up your iPod and try to update it again. Is it successful now?
If you can update your iPod, save the update file to your computer, incase you have to go back to this version at some future point. Right click on the desktop icon and send the file to your preferred storage disk. -
I just bought v10.7lion but when I try to install it comes with this error message:"Install Failed"...try to install again. Now I've been restarting over and over again. What should I do?
JPPI-
Did you try it with the iTunes your Mac already has?
Try running Software Update in your System Preferences. That should bring your computer up to the latest software available for 10.4. You would end up with an older version of iTunes, but that may be good enough to activate your iPad.
Fred -
I can't open firefox after upgrading to 4.0
I get the message over and over again that i have to restart my computer for upgrading to firefox.
I tried new installation. But i got problems on all my accountsStart your '''Computer''' in safe mode. Then start Firefox. Try '''Safe''' web sites.
Starting The Computer In Safe Mode;
If running, turn your computer off.
Remove any disks and thumb drives that are in your hard drives or ports.
Now start your computer but also;
'''Windows; '''Press the <F8> key repeatedly.
'''Mac: '''Hold down the Shift key.
'''Linux; '''Using the command line, Linux/Unix computers can be booted
into various run levels that determine which resources are loaded.
For example, "runlevel 1" is typically the equivalent to Windows and
Mac safe modes.
* Source; '''[http://encyclopedia2.thefreedictionary.com/Linux+Safe+Mode Safe Mode; Free Online Encyclopedia]'''
When the '''Boot''' menu is displayed, release the key you were pressing.
You must now choose what mode to use. The most used are;
* Safe Mode; The computer runs with only a minimum set of programs.
* Safe Mode '''With '''Networking; Same as above, but with internet access. -
ITunes cannot play my rented movie. The timeline stops and no error message pop up.
I rented two movies from iTunes store yesterday. It's still valid. But my iTunes cannot play it. After I click on the 'play' button, the timeline does no move forward and the screen remains in black. No error message pops up. What's wrong with this iTunes player??
wiclee wrote:
It's always the case because iCloud is active all the time and if the device indicated Backup to iCloud an your computer indicated Backup to Computer, you may run into problem.
But this can never be a problem. When you select "Back up to computer" and press apply, iTunes "updates files" on the iphone. I'm not an engineer and my best guess is that by updating the files iTunes changes the device's settings to point to "Backup to Computer".
[Earlier: The sync button used to be visible only after the files were updated. Now, when "Back up to Computer" is selected and we press apply, iTunes indicates that its updating files but the option then shifts back to "Back up to iCloud"]
Incidentally, I was playing around with this and I clicked on encrypt local back and set a password and iTunes accepted that and updated the backup on my computer. This is pretty wierd considering its not accepting "Backup to computer" otherwise.
wiclee wrote:
I wonder how you were able to do that without turning off iCloud Backup on your device.
I guess the older versions of itunes supported that. This problem cropped up after updating to 10.6.0.4
wiclee wrote:
iTunes 'open when this iPhone is connected' works only when you connect using USB cable.
With Sync over wifi enabled iTunes used to open automatically for me whenever my iPhone logged onto the wifi network. Which was a very useful feature for me. I'm extremely disappointed that this is not working now. -
Guys,
my iphone 4s is not working. I tried to restore it but an error (1) message appears over and over again and No serial number is display, shows as n/a in itunes.
my serial number is C38HGK63DTD2
please help
Regards
Manuela CostaError 1 indicates a serious hardware failure. Take the device to Apple for evaluation.
-
I updated my ipad but had to skip the update to the icloud because it was not finished within 2 hours. The ipad worked fine then, but I turned it off. When I tried to turn it on again, it kept asking for the password over and over. What do I do now?
iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
How to Reset a Forgotten Password for an iOS Device
http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
Saw this solution on another post about an iPad in a school enviroment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just cancelling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
Cheers, Tom -
Could Not Open Key Error over and over and over
Error Message- "Could Not Open Key HKEYLOCALMACHINE\SOFTWARE\CLASSES\QuickTimePlayerLib.QuickTimePlayerApp\CLSID"
Just got a new IPOD for Xmas but can't install Itunes. I think the problem is Quicktime. I have been searching in this discussion for people with the same problem and I have tried everything. I tried giving myself access in the registry editor but it won't let me. It says "Cannot save permission changes.......Access is denied." I tried deleting all the Quicktime files but it says "cannot delete files.....error while deleting." I have even tried the response to the 1400's error messages but nothing works. Also installing Quicktime by itself, same thing. Same error message over and over. Please help!!!!
Compaq PC Windows XPoh my god please help!!
-
Can't use the Adobe PDF pack I paid for. Asks me to subscribe over and over!
i have been subscribed to the Adobe PDF for a couple months now, but for about two weeks now, the app won't let me convert word documents to PDF -which is what i pad for. Instead, whenever I click on the little icon, the subscribe for 9.99 dollar pops up, over and over again! I click subscribe, and a message appears, saying I'm already subscribed and that my service will be renewed every month (June 12 I believe) AND the service is still being paid for! how can you solve that?
In the Reader home screen, could you make sure that you are signed in with the Adobe ID that was used to pay for the subscription? (Please do not reveal your Adobe ID on this pubic forum here.)
-
"Sign In To iCloud" keeps popping up over and over again - HELP!
Hi,
Recently I have been having trouble trying to fix my issue with my second hand iPhone 5 (32gb). About 5 months ago I had bought this iPhone and everything was fine. Until yesterday a message popped up stating that I need to sign in to iCloud. The apple ID was not mine nor did I know this email so I tried pressing cancel but it kept popping up over and over again. I cannot do anything to my phone right now and had tried searching up for a solution to this extremely annoying problem but found no fix. My phone is connected to Wifi and I've tried rebooting, but haven't restored and reset since I'm scared that it might turn up to be an activation lock. I have tried contacting Apple Support but they've put me to hold for a very long time which I can't do anything about and I'm afraid that I have come to a dead end. Also, I've tried contacting the owner of the iCloud account but they haven't replied yet so I'm anxiously waiting for a solution. Please, PLEASE PLEASE help me since I'm desperate for an answer and will need a phone in the next few days.
Best regards,
Andy- iPhone 5, iOS 7.1I have the loop issue solved. It seems it was as simple as turning the wifi back on. It got shut off and I was unaware. It was really hard to go through the settings menu with the sign in box continually popping up. Thanks for offering to help.
Maybe you are looking for
-
Which is better verizon or att for cellular?
which is better verizon or att for cellular?
-
Duplicate entries missing using for all entries in select query.
Hi Gurus, Is there any way to avoid missing duplicate entries in an internal table if you use for all entries in select statement? Note : i am selecting two tables using non key fields and i have to aggregate the data. I want only 2 data fields and o
-
SQL Developer: Right-click format doesn't work right with DATE datatype
Hi All! Currently I'm using version SQL Developer Version 3.1.05. Got a question regarding the 'auto-format' of syntax whenever writing in the code editor. If you take this snippet of code and drop it into a worksheet, then highlight it, right click
-
Can I create a private iCal event in iOS?
Can someone tell me how to mark an event as private with iCal using iOS? Thanks!
-
I'm just starting to learn Java and I've been using NetBeans 7.3 I was trying to test out JavaFX but when I tried to import different class files from the JavaFX library it says javafx does not exist. I installed Java JDK 7 which has javafx installed