Error Message When Recording

Hello I am constantly getting an error when I try to record in Adobe Audition CS5.5. It keeps saying the input and output device sample rates don't match. So I cannot record my voice. What do I do?

You'll need to make sure that the sample rate for your input and output channels of your device match.
1. Right-click on the speaker icon in the lower-right corner of your desktop and choose Recording Devices
2. Right-click the Microphone (or desired input channel for the device) and choose Properties
3. Click the Advanced tab and verify or change the Default Format option
4. Click OK then click the Playback tab. Right-click on your default or desired output channel and choose Properties
5. Make sure the Default Format option matches what you selected for your recording channel. (You'll notice in this screenshot, my playback device is configured for 48,000Hz while my microphone was configured for 44,100Hz. These need to match.)
6. In Audition, create a new session. For best results, ensure your session sample rate matches the sample rates you selected for your decices. Audition will attempt to convert the sample rate of your recording on-the-fly to match the session sample rate, but it's always recommended to work at a single, consistent sample rate to ensure no change to the audio signal takes place.

Similar Messages

Error message when recording video

Have QT 7 Pro and it sees my camera, I set up hit record and I see the audio bar moving but the screen is black. When I stop the recording I get this error message:
*RECORDING FAILED BECAUSE NO DATA WAS RECEIVED*
*Make sure that the media input source is turned on and playing.*
Well the device is plugged in and turned on and the Mac sees it on the QT program because when I choose 'Movie Inspector' my camera is chosen as the source. Also the A/V settings are greyed out as to not be able to adjust.

Check that your video drivers are up to date.

System Overload/Core Audio Error Message when recording/playback

Well ive been experience this problem for a while now but ive read up on it and done some troubleshooting and think i may have found a solution.
Well what happens is ill be recording say one track or 2 tracks in mono or stereo or playing back about 3 or 4 tracks and logic will stop everything and give me an error message which either says system overload or core audio overload or something. Well i figured i was overloading my cpu so what i tried doing was restarting my computer and then only operating logic as the only program. this worked temporarily sometimes but not in the long run. well i did research and came to this.
apparently its too overbearing for my Powerbook processor to record in 24 bit/96 Khz which is kind of a bummer because it was one of my attractions to my i/o box that i could do that. also freezing tracks will help greatly apparently which i have yet to try but hope will work too.
also i recently deleted about half of the stuff on my internal drive and put my 42.41 GB of music onto my external HD so now i have 54.6 GB on my internal HD which holds about 93 GB total. should this help me greatly? or will it only be a minute difference?
well any more solutions/suggestions as to what i can do to better my situation? also am i correct as to why i think i get those error messages.
ps: sorry for the uncapitalization, i got a bit lazy here
thanks
-Mike

Mike,
Bit depth is more important for recording quality than huge sample rates. If you're going to change your settings, I'd stick with 24 bit, but reduce sample rate to 48 kHz.
When you say you've put all your music on the external drive, what exactly do you mean--your Logic files or your mp3/AAC files? Normally you would want to use an external drive to record onto from Logic. That way your internal HD can run the OS and Logic, while the external is free for all the fast recording tasks. (This assumes your external HD is pretty fast, and ideally is firewire.)
Freezing works wonders, too, if you're processing tracks.
-Eric

Error message when loading BALTB record

I am receiving the following error message when trying to load the BALTB record.
Unexpected record type.
Key of data record which caused termination:
Client = ,
Company Code = 1000,
Asset Class = 153000,
Old main number = 99948,
Old subnumber = ,
Transaction = AS91,
Record type = B . 
I have search the forum for answers but I can't seem to find any resolutions. Has anybody encountered this problem and were you able to correct it?
thank you in advance for the help.

BALTB seems to be a structure , can you explain how you r trying to loadd
The error may be the Record type B is invalid , the last field is record type , chk whether B exists or not

I updated my itunes to 11 and found out my phone and ipod were not compatible. I uninstalled it and reinstalled 10.7 but now I get an error message when I try to open itunes saying "the file cannot be read because it was created by a newer verison"

I updated my itunes to 11 and found out my phone and ipod were not compatible. I uninstalled it and reinstalled 10.7 but now I get an error message when I try to open itunes saying "the file cannot be read because it was created by a newer verison" What do I do?

Thank you for clarify I'm supposed to read the ENTIRE article. I thought I was just supposed to read the title and magically everything will fix itself. I appreciate you taking the time to help me however I do not appreciate the caps and the way you have addressed the situation. If you are not going to kindly help people/make suggestions just don't try! And for the record my conclusions are not illogical, the iOS7 thing is on the website in small font (which I got by reading the ENTIRE thing) and you should really find a new hobby because your socialization skills need some help! That goes for you too Chris. Not everyone is a tech nerd

Error message when trying to order on line

Anyone else getting the below error message when trying to order the iPad2 online in Europe?
An error has occurred during your session. Please return to the Store Menu to continue shopping.

Be aware that this happened to me and when I contacted my credit card company, they said Apple had contacted them to take the money, yet no order is appearing on my account so now I'm stuck in limbo - my credit card company has approved the transaction yet I have no record or order number with which to question apple about it
The guy at the call centre also said he had received several calls about apple over the last 30 mins so this is not an isolated incident
S.

Error message when importing data using Import and export wizard

Getting below error message when importing data using IMPORT and EXPORT WIZARD
Error 0xc0202009: Data Flow Task 1: SSIS Error Code DTS_E_OLEDBERROR. An OLE DB error has occurred. Error code: 0x80004005.
<dir>
<dir>
Messages
Error 0xc0202009: Data Flow Task 1: SSIS Error Code DTS_E_OLEDBERROR. An OLE DB error has occurred. Error code: 0x80004005.
An OLE DB record is available. Source: "Microsoft SQL Server Native Client 11.0" Hresult: 0x80004005 Description: "Could not allocate a new page for database REPORTING' because of insufficient disk space in filegroup 'PRIMARY'.
Create the necessary space by dropping objects in the filegroup, adding additional files to the filegroup, or setting autogrowth on for existing files in the filegroup.".
(SQL Server Import and Export Wizard)
Error 0xc0209029: Data Flow Task 1: SSIS Error Code DTS_E_INDUCEDTRANSFORMFAILUREONERROR. The "Destination - Buyer_.Inputs[Destination Input]" failed because error code 0xC020907B occurred, and the error row disposition on "Destination
- Buyer_First_Qtr.Inputs[Destination Input]" specifies failure on error. An error occurred on the specified object of the specified component. There may be error messages posted before this with more information about the failure.
(SQL Server Import and Export Wizard)
Error 0xc0047022: Data Flow Task 1: SSIS Error Code DTS_E_PROCESSINPUTFAILED. The ProcessInput method on component "Destination - Buyer" (28) failed with error code 0xC0209029 while processing input "Destination Input" (41). The
identified component returned an error from the ProcessInput method. The error is specific to the component, but the error is fatal and will cause the Data Flow task to stop running. There may be error messages posted before this with more information
about the failure.
(SQL Server Import and Export Wizard)
Error 0xc02020c4: Data Flow Task 1: The attempt to add a row to the Data Flow task buffer failed with error code 0xC0047020.
(SQL Server Import and Export Wizard)
</dir>
</dir>
Error 0xc0047038: Data Flow Task 1: SSIS Error Code DTS_E_PRIMEOUTPUTFAILED. The PrimeOutput method on Source - Buyer_First_Qtr returned error code 0xC02020C4. The component returned a failure code when the pipeline engine called PrimeOutput().
The meaning of the failure code is defined by the component, but the error is fatal and the pipeline stopped executing. There may be error messages posted before this with more information about the failure.
(SQL Server Import and Export Wizard)
Smash126

Hi Smash126,
Based on the error message” Could not allocate a new page for database REPORTING' because of insufficient disk space in filegroup 'PRIMARY'. Create the necessary space by dropping objects in the filegroup, adding additional files to the filegroup, or setting
autogrowth on for existing files in the filegroup”, we can know that the issue is caused by the there is no sufficient disk space in filegroup 'PRIMARY' for the ‘REPORTING’ database.
To fix this issue, we can add additional files to the filegroup by add a new file to the PRIMARY filegroup on Files page, or setting Autogrowth on for existing files in the filegroup to increase the necessary space.
The following document about Add Data or Log Files to a Database is for your reference:
http://msdn.microsoft.com/en-us/library/ms189253.aspx
If there are any other questions, please feel free to ask.
Thanks,
Katherine Xiong
Katherine Xiong
TechNet Community Support

Error message when connecting 80GB Video iPod

I'm getting this error message when trying to connect my 80GB Video iPod:
"The iPod (name) cannot be synced. An unknown error occurred (-48)."
Never seen this one before.
I haven't synced this iPod for a few weeks but it always behaved fine before, taking a few seconds to appear in iTunes (v7.5) then syncing perfectly when I hit the Sync button (I have it set to manually sync only because sometimes I want to change the contents or only sync music).
Before syncing on this occasion, I did an iPod software update via iTunes - iTunes said there was a newer version (1.2.3). After the update, I disconnected the iPod for a few minutes (somehting I wanted to check content before syncing), then reconnected it. At first iPod took about a minute to show up in iTunes - way too long. I Reset the iPod and tried again but still LONG delay to appear in iTunes (again about 1 minute). I did another Reset - same result. Then I did a complete Restore, after which syncing to restore the contents gave problems - it refused to finish the sync. I had to disconnect and start again, syncing the data one section per sync session - Contacts, music, videos, iCal - which seemed to work fine. Then I disconnected, waited a few minutes then reconnected the iPod to check. It wouldn't connect at all. Did a Reset, tried o connect again and it did connect but then proceeded to resync all my contacts taking almost 30 minutes (way too long) to do so (I had made NO changes in Address Book since that data was put in there). I tried to reconnect again but then got the error message (above). Did another total Restore and the same shenannigans happened. Now, I have an iPod with data on it and works fine, but iTunes won't recognise it - just gives this error message every time.
By the way, my 8GB Nano (software 1.1.3) seems to sync fine on the same system, same computer.
Could this be the 1.2.3 iPod software giving issues? I appreciate any help because I also use this iPod for recording for my work, which getting a little urgent now.
Many thanks.

Thanks Zevoneer, but no real success. I did all that but when I tried to sync after it, it got partially through the sync (about 10% I'd guess) and presented an error message saying that the disk couldn't be read form or written to (sorry but I forgot the error number). I disconnected the iPod, waited a few minutes then reconnected and again got the message but then the ipod continued to finish the sync, even though almost all of the music and 2 of my 4 videos didn't go over to the iPod. I'm now thinking that this just isn't satisfactory reliability from the device since I use it a lot in my work and rely on it. But this new iPod is only a few months old, had very little use and only made about 12 recordings - In comparison, I've used the Nano heaps but now want to move over to the bigger one, basically for more capacity and bigger screen for video. I wonder if it's a hard drive failure in this iPod?
null

Virus on Hard Drive-Error Message When Trying to Backup Songs

I think I have finally figured out how to select all my songs including ones purchased through iTunes. When I click in the upper right with a CD-R, DVD-RW, CD-RW in the upper middle of iTunes I get the following error message:
Disc Recording Not Found
What does this mean? As a test, I took a file and copied it directly to the CD and it worked fine on the CD-R.
Also, when I copy these songs onto the CD will it copy the artwork as well for my Nano?
HELP! I need to reformat asap.

done

Error message when printing Sales Order

Hi,
I get following error message when printing out a sales order just created.
No matching records found 'Document' (RDOC) (ODBC-2028) (Message 131-183)
Logged in as super-user, posting periods is unlocked. It is a new company just created. With sand-box company no errors-it prints properly to same printer.
What could be the problem?
Thanks,
Ajay Audich

Have you tried with system PLD?
Thanks,
Gordon

How do I deal with this error message when burning DVD's: The disc can't be burned, because the device failed to calibrate the laser power level for this media.

I am getting this error message when trying to burn a DVD: The disc can’t be burned, because the device failed to calibrate the laser power level for this media. iMac, Mac OS X 10.6.8 Memorex DVD-R 12x Any ideas?

First, try a different batch of recordable DVDs. If you still have problems, you may want to make an appointment at the genius bar and have it checked. The drive may be failing.

Error message when opening adobe premier 10 saved film file , this file is not supported or required codec not installed

Hi
Can any one help, keep getting error message,error message when opening adobe premier 10 film file , this file is not supported or required codec not installed,
Thanks
Colin65

Steve,
Not to sure what type AVI files they are, the storage devise is at present offshore on a job.
Can you clarify, if you edit/import video footage with adobe premiere 10 and then create a file, the file or the original raw footage is not stored on computer for re-use, if it is stored, is it stored in the original format.
Also please find details of storage devise,
Dogcam Portable Media Center PMC-500r
Quick DetailsModel Number:PMC-500R
SpecificationsPMC-500R20G/40G Portable Multimedia PlayerPMC-500R 20G/40G Portable Multimedia Player, Supports
PMC-500R20G/40G Portable Multimedia PlayerPMC-500R 20G/40G Portable Multimedia Player, Supports MPEG-4 File FormatsKey Specifications/Special Features:Video recorder: supports digital video recoding in MPEG4 from Line-in Video playback: supports MPEG4 (AVI), MPEG1 (.MPG), DVD (MPEG2,.VOB) Supports MPEG4 with 720 x 480 at 30 Frames/s MPEG4 movie playing with Fast Forward, Fast Reverse, Time search function Music playback: supports MP3, WMA, WAV Music playing with play list function MP3 ID3 information and sorting, LRC Music playing with repeat, shuffle playing function Photos view: supports JPEG and slide show, rotate, nail view Easy backup of photos in digital camera -USB OTG technology Audio recording: continues recording for over 40 hours High resolution output for HDTV (Y, U, V output; 704 x 480 (N) or 704 x 576 (P), at 25/30 frames/s) Super dlim size: 126 x 79 x 22.5 mm Games E-book with bookmark, auto turning page, page search function File browser function with Copy, Delete, HDD capacity information With 3.5" LCD QVGA TFT panel (960 x 240) Long time battery running (over 5 hours for video, and 9 hours for audio) 1.8" 20G/40G storage capacity High fidelity sound with good earphoneCompass Electronics Co.,

Error Message When Loading FLV

I'm getting this error message when I run this movie -
"Error #2044: Unhandled AsyncErrorEvent:. text=Error #2095:
flash.net.NetStream was unable to invoke callback onMetaData.
error=ReferenceError: Error #1069: Property onMetaData not found on
flash.net.NetStream and there is no default value.at
Slide_GB_05_fla::MainTimeline/frame1()".
My code to load the five FLV's is -
var nc1:NetConnection = new NetConnection();
nc1.connect(null);
var ns1:NetStream = new NetStream(nc1);
theVideo1.attachNetStream(ns1);
ns1.play("Safety.flv");
var nc5:NetConnection = new NetConnection();
nc5.connect(null);
var ns5:NetStream = new NetStream(nc5);
theVideo5.attachNetStream(ns5);
ns5.play("Dutyfree_3.flv");
var nc3:NetConnection = new NetConnection();
nc3.connect(null);
var ns3:NetStream = new NetStream(nc3);
theVideo3.attachNetStream(ns3);
ns3.play("Hawaii.flv");
var nc4:NetConnection = new NetConnection();
nc4.connect(null);
var ns4:NetStream = new NetStream(nc4);
theVideo4.attachNetStream(ns4);
ns4.play("CatWoman_1.flv");
//ns4.seek(10);
//ns4.pause();
var nc2:NetConnection = new NetConnection();
nc2.connect(null);
var ns2:NetStream = new NetStream(nc2);
theVideo2.attachNetStream(ns2);
ns2.play("CITA_1.flv");
ta1.textField.background = true;
ta1.textField.backgroundColor = 0xC9C1B8;
//ta1.htmlText = "Kinds of PAVES
entertainment:<ul><li>Audio
channels</li><li>Video
programs</li><li>Airshow</li></ul> Examples
of video
programs:<ul><li>Safety</li><li>Comfort
in
Flight</li><li>Destinations</li><li>Movies</li><li>Advertisements</li></ul>";
var lessonInfoXML:XML;
var lessonInfo:URLLoader = new URLLoader();
var smartGraphicFile:String;
lessonInfo.addEventListener(Event.COMPLETE,
onCompleteLessonInfo);
lessonInfo.load(new URLRequest("Slide_Information.xml"));
function onCompleteLessonInfo(evt:Event) {
lessonInfoXML = new XML(lessonInfo.data);
smartGraphicFile = lessonInfoXML.slide5.narration;
ta1.htmlText = smartGraphicFile;
The FLV's load, and I can dismiss the error messages. Any
idea what I'm doing wrong?

BALTB seems to be a structure , can you explain how you r trying to loadd
The error may be the Record type B is invalid , the last field is record type , chk whether B exists or not

T4i Rebel error message "movie recording has stopped automatically"

I was recording my client when suddenly I got a this error message "movie recording has stopped automatically" and I could not record video anymore. I am recording on a class 10 sandisk Ultra card. 720/60, EFS18-135mm lens. Never had any problems in the past. First I get a small veterical meter on the frame and then after 5 secs the recording stops with this error message. Please tell me it is opeartor error...I have had this camera for 2 years now and never had a problem. I tried multiple cards.
thanks for the help,
DM

Either you or the person you spoke to at Canon was confused.
What the camera requires for video purposes is a card which is "at least" Class 6 or faster. The class designation is an indicator of the cards data transfer speed. Class 6 actually means the card is capable of transfering data (either reading or writing) at "at least" 6 megabytes per second. A Class 10 card can transfer data at "at least" 10 megabytes per second.
The T4i is also compatible with "UHS-1" cards... which are significantly faster than eithe Class 6 or 10.
The reason for requiring "at least" Class 6 has to do with how fast the camera is attempting to capture and save frames of video to the card. The camera actually has an internal memory buffer which is very fast. When you start recording, the data is being saved to that buffer... and simultaneously the camera also starts taking the data from the buffer and saving it to the memory card (which is slower). If the camera is recording video only slightly faster than the card can record, then it will actually take a few minutes before the buffer is completely filled. But at that point the camera has no choice but to stop recording because it has absolutely no place to save data ... the internal buffer is full and it can't empty the buffer because the memory card can't save data as fast as new frames of video are coming in.
Faster is always better.
Memory cards do actually wear out and develop errors over time. This is normal. A good card will re-map the bad blocks so they aren't used anymore... and this is why you should do a low-level format IN CAMERA (not using the computer). Good cards also have a "memory leveling" technology to try to use all the blocks roughly an equal number amount. This extends the userful life of the card.
When replacing the card, do not skimp on quality! I cannot emphasize that point enough. Most times when someone brings up this issue... it's the card that is having problems and not the camera.
It's easy to produce forgery cards which look like a good brand but are not. Buy GOOD cards from REPUTABLE dealers. Do not shop for the cheapest website on the Internet with a questionable reputation in order to save a couple of bucks.
Lexar brand and SanDisk brand are good.
When buying memory cards, I only buy cards from Lexar and SanDisk. I also buy their highest end cards (by speed performance... not necessarily their biggest capactiy cards). I buy the cards from dealers with a solid reputation. This avoids the unpleasant error messages which always seem to happen at the worst possible time.
Tim Campbell
5D II, 5D III, 60Da

Licence error message when using automation software

Error message when using Rational Functional Tester 7.0.1.1
to record a Flex application. The message seemed to come from the
Flex application.
I can record a fiew step in the application, then I have the
message : "Licence are not present. Eith the trial version only
limited record are allowed". But, my license of my Rational
Functional Tester application is activated.
I am using a Flex builder 3 trial version and the trial is
not over.
Is there any problem to get the license in the File compiler
with "D:\apps\IBM\SDP70\FunctionalTester\bin\rft.swc"? That RFT
file is supposed to be included in the flex application once
compile

Does anyone know how to build with automation support in a
linux environment?
We simply run an ant script build and have the SDK installed.
We purchased Flex Builder Professional, but cannot install on Linux
(we don't want to use the alpha version).
Thanks for any pointers :)

Error Message When Recording

Similar Messages

Maybe you are looking for