Error messahe re fire wire

when I plug my iPod in to my car charger, I get a error message words like " Can not connect using a fire wire connection, switch to a usb connection..." at the bottom is states "Push middle button to dismiss", What does this mean. Also when I push middle button the error message does not go away.

further to this post, this also happens when I sync to my computer. After the saync process and i disconnect, and try to play music this error shows. The actual wording is "Fireware connections are not supported. To transfer songs, connect the USB cable provided: and again at the bottpom is says "Press Center to dismess". And the error does not dismiss when I push center.

Similar Messages

Fire Wire Error Message:

If anybody has been following my posts, I have been wanting and needing a fire wire enclosure for large hard drives. I only have one of each. A Fire Wire enclosure and a 3.5 PATA drive. A Maxtor 160gb. I have other hard drives and they are smaller, and have issues. Fortunately OS 9 is able to mount these damaged drives.
I am very happy to have a fire wire enclousre and also a new hard drive for my files. =] =] And I still have like a bunch of files to organize but the most important thing right now is to get all of these files off of three messed up hard drives.
I have one hard drive connected to a USB enclosure and the new 160gb one is connected to the Fire Wire enclosure. (It also has a USB 2.0 port but I am connecting it to Fire Wire) and I am running OS 9 while operating all the external hard drives.
As for the fire wire enclosure: I get an error message:
A FireWire disk has stopped responding. The problem must be corrected to prevent damaging the disk's contents.
Please check all FireWIre connections. If you added, removed, or turned on a FireWire device on or off, try undoing what you did.
And so I turn off the drive and turn it back on. It acts like nothing has happened to it. But certainly something bad is happening!!! =S
Also it has done this in the middle of transferring files and then I turn it off and on and then it resumes moving THE SAME file!!!!!!! =S
????????????????

Could the problem have been the USB-only enclosures??????? I have tried to get it to work a few minutes ago and it would not turn on. I gave up on it and I disconnected it. I am moving files from the damaged hard drives onto that imac's internal hard drive, and then onto the new hard drive ... all using the same fire wire enclosure. I have one so far and not two... and that is kinda frustrating. =S }=S }=S
Even though I have to keep switching hard drives with one fire wire enclosure, the fire wire enclosure transfer speed is now FAST!!!!!!!!
=]

Unable to mount external fire-wire hard drive - help, please!

After working the last couple of days to resolve the failure of an internal drive, now one of my external drives (LaCie fire-wire) will not mount. I was using it to back up the bad internal drive, and probably forgot to eject the drive before turning it off; don't know if this really makes any difference, but just in case...
If I use Disk Utility I can see the LaCie drive, but it will not mount.
When I tried to verify the drive got the following message -
Invalid sibling link
The volume LaCie HD needs to be repaired
1 HFS volume checked - volume needs repair
Next I tried to repair the drive, and was told -
Invalid sibling link
Volume check failed
Error: The underlying task reported failure on exit
1 HFS volume checked
1 volume could not be repaired because of an error
This is where I stopped. I read another post somewhere in the forums about making a disk image of the drive, but I'm afraid of making things worse by proceeding without knowing what I'm doing. Any ideas on how I can somehow retrieve the data in the LaCie drive?
Once again, thanks in advance for any help!

Hi! Diskwarrior is always better at repairing drive directories which constitute 99% of all drive problems. I run it fairly regularly usually once a month. BUT I always run it at the first sign of weirdness or problems AND every time I have had a power failure or a forced restart or shutdown because those events usually always damage the drive's directory. Often even though the directory is damaged OSX can go ahead and mount it and it will work ok but eventually the damage builds every time one of those events occur and finally there is a failure to mount or boot. Tom

Fire wire cam doesnt work im messages chat

my fire wire Unibrain cam does not connect in messages chat and I cannot receive the other persons cam
. Are there settings I should correct. I am using 10.8.4

HI,
So you are getting video in to the App.
So any Firewire 400/800 issues are moot.
Next step.
In the Video Menu is the Video option dark and active text and is it ticked ?
In the View Menu is Show Video Status ticked ?
This Menu and the items from show Buddy Pics down rely on a Buddy list being "front" (More on that in sec).
The first of these makes sure the camera is On and the second makes sure the Buddy Lists display the Video icons.
If there is not enough Internet Speed for Video Chats then the Video items may be ticked but greyed out.
To make sure you can see the Buddy Lists go to the Window Menu.
If you have set up iMessages and nothing else except Enable the Bonjour account then the Buddies item will dispaly the Bonjour list.
If you have AIM, Jabber or Yahoo IDs set up as well then the Buddies item is a combined list.
You can unlink them in the General section of the Preferences.
The Window Menu will change to list the Buddy Lists by the Description Fields in the Accounts section
An AIM Buddy list for example should display green Video icons next to the Buddies.
In this my other logged in AIM valid Names show up under Family and an Apple Test accounts shows in Auto Responders (you can't Video with yourself but you an add the Buddy name to a Buddy list).
Only Jabber Buddy list will do this as well as the Yahoo option is Text only.
However it does have to be AIM to AIM or Jabber to Jabber.
AIM in this sense includes the Apple Issued IDs with the ending of @mac.com, @me.com and @icloud.com
Jabber ones can include GoogleTalk and Facebook IDs if you have Enabled Talk at Google or Chat at Facebook.
Sticking with the AIM case you would then click on the green video icon as one method of Starting a Video Chat.
As it is an AIM Buddy list the Buddy should be an AIM vlaid Buddy.
Note
Apple IDs obviously have an @ in them and in most cases are valid emails (or have been in the past)
They are valid with the AIM service
GoogleMail IDs are then valid Jabber IDs once you enable Talk in Products at Google. Facebook also uses the users email Address.
The can means that fro both services an email address is the valid ID.
Other Jabber IDs may not be email but do follow the [email protected] format.
This means it is possible to add the IDs or Screen Names from one service to the Buddy list of another.
The Buddy will appear Off line in these case but you will not be told they are not a valid Buddy.
If the chat fails at this point you normally get some sort of alert message.
It may even have pop up that can be expanded for more details.
You may see more in the Video Menu > Connection Doctor > Errors tab
If you have an AIM Buddy list then try adding the Apple Test Accounts. See table 1
There used to be 6 (three plain AIM names and three @mac.com versions).
It tends to be that only 1 or 2 are On at any one time now.
Can you connect to this "Buddy" ?
8:22 PM Wednesday; July 17, 2013
 iMac 2.5Ghz 5i 2011 (Mountain Lion 10.8.4)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad
"Limit the Logs to the Bits above Binary Images."  No, Seriously

Fire wire ports driving me batty

I have a late 2007 Intel iMac with a total of 7 Lacie external hard drives daisy chained together via the 800 fire wire ports. The externals are stacked one on top of the other. I cannot hook up the 8th hard drive to the 7th one (the hard drive on the top is #1, the one on the bottom is #7) without losing the 7th hard drive (I get an error message saying that the #7 hard drive hasn't been disconnected properly) and it disappears from the desktop. However, if I attach the 8th hard drive via the 400 fire wire port, all is well. I've switched the order of the hard drives and used different cables, but it always seems that the 7th hard drive has an issue with both 800 ports being used. Anyone have a suggestion (other than hooking up the 8th to the 400 port) or an answer to why this is happening? I think maybe heat might be a factor.
Message was edited by: Sunny's mommy

I don't think the hard drives have internal fans. Anyway, I've tried switching the order, like hooking up #1 & #2, with #2 on the bottom, then hooking up #7 to #2. Changed around the order - sometimes it works and sometimes it doesn't, but it's pretty consistent, that whenever one of the two 800 firewire ports on the bottom one is in use and I attach another hard drive to the free firewire port, it freaks out the bottom one. However, when I use the 400 firewire port, all is well. Anyway, in the grand scheme of things, I'm not going to lose sleep over it. Was just wondering if it's the way I'm setting things up. By the way, what is a bridge board?
Message was edited by: Sunny's mommy

Video out fire wire port from iTunes?

Final cut and Pro Tools LE both have the ability to send video from a G5 to a TV out of the fire wire port via a Canopus ADVC-110. Why doesn't iTunes? I understand that the new Mac TV gizmo plus an airport card will do this, but I already have all the hardware I need for this to work. I just need iTunes to take advantage of the same external video option that Final Cut and Pro Tools LE have. Anyone know of a patch or something that would make this happen. Or at least a stand alone player that will play the m4v iTunes video files and play video out fire wire port to my canopus which will then send it to the TV?

In an attempt to get my iTunes downloaded TV episodes to play on my TV without having to buy the Apple TV hardware and an airport card I have been trying to find a way to convert the m4v video files into a format that can be read by a stand alone player that allows me to output video playback through my fire wire port so my canopus box can then send it to my tv and stereo. I tried iSquint and it does not work. I get an AppleScript error "Can't make "" into type real. (-1700)" If you hit OK the program then spins it's wheels with the progress report "Preparing Audio for File 1..." It is still my belief that Apple should enable iTunes to output video through the fire wire port. Since Final Cut Pro and Pro Tools LE have that ability and it works I assume that it should work wth iTunes. Please send iTunes feedback from within iTunes and ask apple to add this option to iTunes.

Details on booting from a Fire Wire HD

Good day, all
I'm trying to make a bootable back up of my internal hard drive on my old iBook.
I used "Personal Backup X3" to "clone" my drive to a LaCie Fire Wire drive (which is partitioned into two 40 gig parts.
When I boot the iBook (with the LaCie connected) holding down the option key my screen shows my internal hard drive, one curved arrow, and one straight arrow. I infer that the curved arrow rechecks for bootable drives but is that correct? The straight arrow boots the computer from the selected drive.
Since I only see one icon (for my drive), I'm guessing there is a problem seeing the LaCie drive. Could this be because it's partitioned?
Let me know if I'm confused on how this works.
Thanks,
Hugh

Did you correctly partition and format this external drive? See the following:
Extended Hard Drive Preparation
1. Open Disk Utility in your Utilities folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to two. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
Repeat Steps 4-6 for the second volume.
Personally I would use the Restore option of DU to clone your iBook's drive but before you do I would do the following:
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger and Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger, and 4.1 for Leopard) and/or TechTool Pro (4.6.1 for Leopard) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
I would then boot the iBook to be sure that OS X starts up properly. If it does then clone the drive as follows:
How to Clone Using Restore Option of Disk Utility
1. Open Disk Utility from the Utilities folder.
2. Select the destination volume from the left side list.
3. Click on the Erase tab in the DU main window. Set the format type to Mac OS Extended (journaled, if available) and click on the Erase button. This step can be skipped if the destination has already been freshly erased.
4. Click on the Restore tab in the DU main window.
5. Select the destination volume from the left side list and drag it to the Destination entry field.
6. Select the source volume from the left side list and drag it to the Source entry field.
7. Double-check you got it right, then click on the Restore button.
Destination means the selected partition on the external drive.
Source means the iBook's drive.

Enabling VNC or Fire Wire booting

Hello Mac People,
Is there anyway to access "System Preferences" remotely?
I need to check and make sure that "Remote Management" is enabled on a FULL XSERVE server running 10.4.11.
I will be using a Mini-Mac also running 10.4.11; this is only going through a switch (same domain).
I have FULL administrator privileges and have no problem connecting using "Server Admin Tools". And I can telnet in just fine also.
Have tried approximately six GUI VNC applications (Chicken of the VNC, Tight VNC, etc.etc.) and ALL fail with vague error messages.
Also tried a known good PCI video card into this FULL headless server but then the operating system froze at start up. Yes the video card is compatible with 10.4.11.
I have also tied to "kick start" the service as well using:
sudo sh -c "/bin/echo -n enabled > /Library/Preferences/com.apple.ScreenSharing.launchd"
(and several syntax variations mentioned on the web) but the commands also fail.
This is a CRITICAL Mac server that is other wise working GREAT located at one of the companies that I support and of course they do not want to buy "Apple Remote Desktop". Gees .... this company is still running Office 2000 on most of there workstations. And seeing as how other VNC's are failing I'm not even sure ARD would install and then work anyway.
If there is no way to access "System Preferences" remotely. Would someone please be kind enough to explain or point me to a link on how to use a "Fire Wire" connection and a Mini-Mac to start this server.
I have seen it done before..... where a Mac system was started using the operating system on another Mac system. Do I need a particular application?
Thanks in advance <smile>

Thank you VERY much for your replies.
I'm thinking that the operating system on this server must be unstable. I know that Disk Warrior has been run on it in the past. Plus AFP (Apple File Protocol) failed to launch after a restart recently. But getting all of the updates fixed that.
Since this is a CRITICAL server I think what I will do is give them an estimate for a brand new main boot hard drive and set the current hard drive aside as a fall back position.
It looks like Snow Leopard (10.6.**) requires an Intel Processor.
This XSERVE is a G5, RackMac 3,1 with Dual 2.3 processors and it looks like they are not Intel based processors????? But "PowerPC" based processors?????
If that is correct I will see if I can locate there copy of Tiger Server. They just bought SEVEN IMac's running 10.6.2 Snow Leopard and you should be able to get more then six years on a VERY expensive full blade server like this.
Anyway, in the mean time, I really need to see how to boot this server from a known good G5, AKA "Target Disk Mode"
I found a link and will try it either this weekend or the next. I work on a lot of week ends at the companies that I support to stay out of the way of the end users.
http://blogs.techrepublic.com.com/helpdesk/?p=293
Once again thank you all VERY much ........ "Live long and prosper" <smile>

Migration Assistant Won't Recognize "old" MBP via Fire Wire

I purchased a new MacBook: 2.16 GHz, Intel Core 2 Duo, 1 GB 667MHz DDR2 SDRAM, 160 gig drive
As usual when I get a new Mac, I erased the drive installed OS X.4.11-Tiger and personalized the mac.
Along the way, something odd happened. I cannot double click on any application and open it—unless—I place its alias into the dock. Then it opens.
I have run disk repair as well as permissions repair to no avail.
Want to use Migration Assistant to transfer files from my MBP to the MB. However, when I connect the Fire Wire, restart the "old" MBP with the "T" key depressed, the firewire wheel shows—but—the MB will not recognize the MBP. So, I can't transfer any data.
MBP has OS 10.4.10 while the MB has OS 10.4.11. Could this be the issue?
Anyone have any ideas as to how I can get past this?
Thanks,
Tek

I have the exact same problem. When setting up the new MacBook, I attached the firewire cable and restarted the PowerBook into target disk mode. The Firewire symbol appears on the screen but the MacBook gives the error message "There are no versions of MacOS X available on your old Mac". I wanted to test if it is a problem with the MacBook, and found that the MacBook will recognize and mount a portable firewire hard drive. Furthermore, when I tried attaching it to an intel iMac, it recognized it and was ready to import files from it. Therefore it seems that the problem is that the OS X 10.4.11 on the PowerBook is somehow 'invisible' to the MacBook migration assistant. I tried repairing permissions on the old PowerBook, but that didn't help. In the meantime I also ran software update on the MacBook, which brought it up to the very latest version of Leopard.
Could it be that the version of OS X needs to be the same on both machines? Next I am going to backup the PowerBook, then upgrade it to Leopard, then try again. I am surprised more people haven't had this problem, at least I have seen few postings about it.

Problems using FW-7344 with Fire Wire Video Cameras

Is it a bad idea to use the FW-7344 with other devices on the same fire wire bus?
We are trying to use an FW-7344 with a fire wire video camera but we tend to get packet errors that force a reset of the controller. We suspect that the problem is related with the camera and controller being on the same fire wire bus.
We instantly see problems when we connect two FW7344s and one video camera on the same fire wire card.

The NIMax program reads Packet Error. I can't recall the first error that our program reads, but I think it typically says something about not being able to communicate return values from the controller to the host computer.
This makes me think that the NI driver on the host does not retry after failing to get return data from the controller. This assumption may be valid with the PCI version, but probably is not with the FireWire version.
It only takes one camera for this problem to happen, but the problem is intermittent.

How do I connect Apple 20" Cinema Display to orignal MacBook Air which does not have a Fire-Wire port. Is this possible? Any advice would be appreciated. I have the Micro-DVI to DVI adapter. Norm

I Wish to connect my 6 year old Apple 20" Cinema Display to an orignal MacBook Air which does not have a Fire-Wire port. Is this possible? Any advice would be appreciated. I have the Micro-DVI to DVI adapter. Norm

The FireWire cable is just for the FireWire ports on the display. The display will run without it.

How do you hook up a fire wire video camera to the 13 inch aluminum macbook

I have a 13 inch mac book with only USB, but a video camera that only has a fire wire output jack.
How can I hook up the camera with fire wire out to the USB in on the new 13 inch MB?
Is there an accessory I can buy that will do this? Link to the product?
Thanks!

There is no option/accessory to do this. You'll need to get a different camera, or use a computer with firewire.

I'm using iTunes 10.6.1 on an iMac 2,66 Ghz intel core Duo with8GB DDR3 and Lion 10.7.3 I hav 260000 mp3 stored on A My Book 3 TB external Fire wire 800 Drive - when I play songs I get short interuptions every 20 to 30 seconds. Can't iTunes handle that?

I'm using iTunes 10.6.1 on an iMac 2,66 Ghz intel core Duo with8GB DDR3 and Lion 10.7.3 I have 260000 mp3 stored on a My Book 3 TB external fire wire 800 Drive - when I play songs I get short interruptions every 20 to 30 seconds. Can't iTunes handle that number of songs?

I'm using iTunes 10.6.1 on an iMac 2,66 Ghz intel core Duo with8GB DDR3 and Lion 10.7.3 I have 260000 mp3 stored on a My Book 3 TB external fire wire 800 Drive - when I play songs I get short interruptions every 20 to 30 seconds. Can't iTunes handle that number of songs?

IMac can't running any two fire wire hard disks at the same time . which

iMac can’t running any two fire wire hard disks at the same time . which two hard disks have extra power from power socket . If i just insert one of them .No problem . If connect two Hds at the same time. Leopard cant find it and the Hds seem no problem. the machine must be restarted and then use one . No problem . I have formated the HD many times .even if which format is Fat 32 or Mac issue persists .Boot from installation CD used the disk utility . Issue stills . If i used one fire wire HD that get power from power socket and used one fire wire device . Leopard was no problem during this time . Whether is this design problem or my machine hardware problem?My Mac has been changed the logic board by Apple service . Do you have similar case in here????
Message was edited by: KennyG1983

Hi KennyG1983-
How are you connecting these drives?
This may help: What to do if your computer won't recognize a FireWire or USB device
Luck-
-DaddyPaycheck

Install OS 10.2.1 on Fire Wire Drive

If I purchase a Fire Wire Drive and cable, connect to my Pismo, can I install OSX 10.2.4 from a Software Install and Restore disk and use this drive for OSX activity? How should it be set up? Where can I find instructions for such a task?
Mac PowerBook G3 (Pismo), 400MHz, 10GB HD, 320MB Ram, DVD Drive, 2 USB & FireWal Mac OS 9.0.x

Homer, welcome, yes you can, however, I would highly recommend using Carbon Copy Cloner to make a bootable backup of your OS on a separate partition on that external.
Joe
Power Mac G4 Gigabit Ethernet Mac OS X (10.3.9)

Error messahe re fire wire

Similar Messages

Maybe you are looking for